1
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
2
3
4
5
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
SID 2A12
en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1
fr Notice d'utilisation originale . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 28
pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 1
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a
prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and
on the product.
• Always keep the operating instructions with the product and make sure
that the operating instructions are with the product when it is given to
other persons.
1.2 Explanation of symbols used
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the
product. The following signal words are used:
DANGER
DANGER !
▶ Draws attention to imminent danger that will lead to serious personal
injury or fatality.
WARNING
WARNING !
▶ Draws attention to a potential threat of danger that can lead to serious
injury or fatality.
CAUTION
CAUTION !
▶ Draws attention to a potentially dangerous situation that could lead to
slight personal injury or damage to the equipment or other property.
1.2.2 Symbols in the documentation
The following symbols are used in this document:
Read the operating instructions before use.
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household
waste
1.2.3 Symbols in the illustrations
The following symbols are used in illustrations:
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
2 English 2235359
*2235359*
These numbers refer to the corresponding illustrations found at the
beginning of these operating instructions
The numbering reflects the sequence of operations shown in the
illustrations and may deviate from the steps described in the text
Item reference numbers are used in the overview illustrations and
refer to the numbers used in the product overview section
This symbol is intended to draw special attention to certain points
when handling the product.
1.3 Product-dependent symbols
1.3.1 Symbols on the product
The following symbols can be used on the product:
The power tool supports near-field communication (NFC) technol-
ogy, which is compatible with iOS and Android platforms.
Li-ion battery
Hilti Li-ion battery type series used. Observe the information given in
the section headed Intended use.
Never use the battery as a striking tool.
Do not drop the battery. Never use a battery that has suffered an
impact or is damaged in any other way.
Direct current (DC)
Rated speed
Forward rotation
Reverse rotation
1.4 Product information
products are designed for professional users and only trained,
authorized personnel are permitted to operate, service and maintain the
products. This personnel must be specifically informed about the possible
hazards. The product and its ancillary equipment can present hazards if
used incorrectly by untrained personnel or if used not in accordance with
the intended use.
The type designation and serial number are printed on the rating plate.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 3
▶ Write down the serial number in the table below. You will be required to
state the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
Type: SID 2-A12
Generation: 02
Serial no.:
1.5 Declaration of conformity
We declare, on our sole responsibility, that the product described here
complies with the applicable directives and standards. A copy of the
declaration issued by the certification department can be found at the end
of this documentation.
The technical documentation is filed here:
Hilti Entwicklungsgesellschaft mbH | Tool Certification | Hiltistrasse 6 | 86916
Kaufering, Germany
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all instruc-
tions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
▶ Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
▶ Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
▶ Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Electrical safety
▶ Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will reduce risk of electric
shock.
▶ Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
4 English 2235359
*2235359*
▶ Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
▶ Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
▶ When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk
of electric shock.
▶ If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
Personal safety
▶ Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal
injury.
▶ Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate conditions will reduce
personal injuries.
▶ Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your finger on the switch
or energising power tools that have the switch on invites accidents.
▶ Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
▶ Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
▶ Dress properly. Do not wear loose clothing or jewellery. Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts.
▶ If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
▶ Do not let familiarity gained from frequent use of tools allow you
to become complacent and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a second.
Power tool use and care
▶ Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 5
▶ Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
▶ Disconnect the plug from the power source and/or remove the
battery pack, if detachable, from the power tool before making
any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
▶ Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands of
untrained users.
▶ Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
▶ Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
▶ Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
▶ Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
Battery tool use and care
▶ Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
▶ Use power tools only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury and fire.
▶ When battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a
fire.
▶ Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
▶
Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
6 English 2235359
*2235359*
▶ Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130° C (265 °F) may cause
explosion.
▶ Follow all charging instructions and do not charge the battery pack
or tool outside the temperature range specified in the instructions.
Charging improperly or at temperatures outside the specified range may
damage the battery and increase the risk of fire.
Service
▶ Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
▶ Never service damaged battery packs. Service of battery packs should
only be performed by the manufacturer or authorized service providers.
2.2 Drill/driver safety warnings
▶ Hold the power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring. Fasteners
contacting a "live" wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
2.3 Additional safety instructions
Personal safety
▶ Use the product only when it is in perfect working order.
▶ Never tamper with or modify the tool in any way.
▶ Do not look directly into the light source (LEDs) integrated in the drill/driver
and do not direct the light at other persons’ faces. This presents a risk of
dazzling or eye damage.
▶ Avoid touching rotating parts. Switch the power tool on only after bringing
it into position at the workpiece. Touching rotating parts, especially
rotating accessory tools, may lead to injury.
▶ Wear protective gloves also when changing the accessory tool. Touching
the accessory tool presents a risk of injury (cuts or burns).
▶ Always hold the tool securely by the grip. If the accessory tool (e.g. the
drill bit) sticks and stalls, the power tool, due to its high torque, may
tend to rotate about its own axis in the direction opposite to that of the
accessory tool.
▶ Make sure that the workplace is well ventilated and, where necessary,
wear a respirator appropriate for the type of dust generated. Contact with
or inhalation of the dust may cause allergic reactions and/or respiratory
or other diseases to the operator or bystanders. Certain kinds of dust
are classified as carcinogenic such as oak and beech dust, especially
in conjunction with additives for wood conditioning (chromate, wood
preservative). Material containing asbestos may be handled only by
specialists.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 7
▶ Take breaks and exercise your fingers to improve the blood circulation.
Exposure to vibration during long periods of work can lead to disorders
of the blood vessels and nervous system in the fingers, hands and wrists.
Electrical safety
▶ Before beginning work, check the working area for concealed electric
cables or gas and water pipes. External metal parts of the power tool may
give you an electric shock if you damage an electric cable accidentally.
Power tool use and care
▶ Secure the workpiece. Use clamps or a vice to hold the workpiece in
position. The workpiece is thus held more securely than by hand and both
hands remain free to operate the power tool.
▶ Immediately switch off the power tool if the accessory tool jams. The
power tool might twist off-line.
▶ Wait until the power tool stops completely before you lay it down.
2.4 Battery use and care
▶ Observe the special regulations and instructions applicable to the trans-
port, storage and use of Li-ion batteries.
▶ Do not expose batteries to high temperatures, direct sunlight or fire.
▶ Do not disassemble, crush or incinerate batteries and do not subject them
to temperatures over 80 °C.
▶ Do not use or charge batteries that have suffered mechanical impact,
have been dropped from a height or show signs of damage. In this case,
always contact your Hilti Service.
▶ If the battery is too hot to touch it may be defective. In this case, place the
product in a non-flammable location, well away from flammable materials,
where it can be kept under observation and allowed to cool down. In this
case, always contact your Hilti Service.
3 Description
3.1 Product overview 1
@
Forward / reverse switch
;
Grip
=
Illumination
%
Belt hook (optional)
&
Battery state of charge indica-
tor
(
Battery release button
)
Control switch
+
Hex. socket
3.2 Intended use
The product described is a hand-held cordless impact screwdriver. It is
designed for tightening and releasing nuts, bolts, anchors and wood screws.
Use the cordless screwdriver only for applications that do not require a
precise/specified torque.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
8 English 2235359
*2235359*
▶ Use only Hilti LiIon batteries of the B 12 series with this product.
▶ Use only Hilti battery chargers of the C4/12 series for charging these
batteries.
3.3 Charge state display
The charge state of the Liion battery is displayed after pressing one of the
release buttons lightly (press only until slight resistance is felt).
Status Meaning
4 LEDs light. Charge state: 75 % to 100 %
3 LEDs light. Charge state: 50 % to 75 %
2 LEDs light. Charge state: 25 % to 50 %
1 LED lights. Charge state: 10 % to 25 %
1 LED blinks. Charge state: < 10 %
Battery charge state cannot be displayed while the control switch is
pressed and for up to 5 seconds after releasing the control switch.
3.4 Items supplied
Impact screwdriver/wrench, operating instructions.
Spare parts, consumables and accessories approved by Hilti for use
with the product can be found at your local Hilti Store or online at:
www.hilti.group
4 Technical data
4.1 Technical data
SID 2A12
Rated voltage
10.8 V
Weight
1.1 kg
(2.4 lb)
Rated speed under no load
0 /min …
2,750 /min
Ambient temperature for operation
−17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
Storage temperature
−20 ℃ … 70 ℃
(−4 ℉ … 158 ℉)
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 9
4.2 Battery
Battery operating voltage
10.8 V
Ambient temperature for operation
−17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
Storage temperature
−20 ℃ … 40 ℃
(−4 ℉ … 104 ℉)
Battery charging starting temperature
−10 ℃ … 45 ℃
(14 ℉ … 113 ℉)
5 Preparations at the workplace
CAUTION
Risk of injury by inadvertent starting!
▶ Before inserting the battery, make sure that the product is switched off.
▶ Remove the battery before making any adjustments to the power tool or
before changing accessories.
Observe the safety instructions and warnings in this documentation and on
the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the
charger.
2. Make sure that the contacts on the battery and the contacts on the
charger are clean and dry.
3. Use an approved charger to charge the battery.
5.2 Inserting the battery
CAUTION
Risk of injury by short circuit or falling battery!
▶ Before inserting the battery, make sure that the contacts on the battery
and the contacts on the product are free of foreign matter.
▶ Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.
2. Push the battery into the battery holder until it engages with an audible
click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release buttons.
2. Remove the battery from the tool.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
10 English 2235359
*2235359*
5.4 Fitting the belt hook (optional) 2
CAUTION
Risk of injury by falling power tools!
▶ Check that the belt hook is fitted securely before beginning work.
The belt hook enables you to attach suitable power tools to your belt, where
they are close to your body. It can be fitted to allow attachment on the left
or right side of the body.
1. Remove the battery from the power tool.
2. Secure the belt hook with 2 screws to the base of the power tool.
3. Check that belt hook and power tool are secure.
6 Types of work
ATTENTION
Risk of damage by incorrect handling!
▶ Do not operate the switches for direction of rotation and/or function
selection during operation.
Observe the safety instructions and warnings in this documentation and on
the product.
6.1 Fitting the accessory tool 4
1. Set the forward/reverse switch to the middle position or remove the
battery from the power tool.
2. Insert the accessory tool into the chuck.
3. Check that the accessory tool is held securely.
6.2 Setting forward or reverse rotation 3
An interlock prevents switching while the motor is running.
The control switch is locked when the forward/reverse switch is in the
middle position (safety lock).
▶ Set the forward/reverse switch to the desired direction of rotation.
6.3 Switching on
▶ Press the control switch.
➥ Speed of rotation is regulated by the distance the control switch is
pressed in.
6.4 Switching off
▶ Release the control switch.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 11
6.5 Removing the accessory tool 5
1. Set the forward/reverse switch to the middle position or remove the
battery from the power tool.
2. Pull the accessory tool out of the chuck.
7 Care and maintenance
WARNING
Risk of injury with battery inserted !
▶ Always remove the battery before carrying out care and maintenance
tasks!
Care and maintenance of the tool
• Carefully remove stubborn dirt.
• Clean the air vents carefully with a dry brush.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning
agents containing silicone as these can attack the plastic parts.
Care of the Liion batteries
• Keep the battery free from oil and grease.
• Use only a slightly damp cloth to clean the casing. Do not use cleaning
agents containing silicone as these may attack the plastic parts.
• Avoid ingress of moisture.
Maintenance
• Check all visible parts and controls for signs of damage at regular intervals
and make sure that they all function correctly.
• Do not operate the product if signs of damage are found or if parts
malfunction. Have it repaired immediately by Hilti Service.
• After cleaning and maintenance, fit all guards or protective devices and
check that they function correctly.
To help ensure safe and reliable operation, use only genuine Hilti spare
parts and consumables. Spare parts, consumables and accessories
approved by Hilti for use with the product can be found at your local
Hilti Store or online at: www.hilti.group.
8 Transport and storage of cordless tools
Transport
CAUTION
Accidental starting during transport !
▶ Always transport your products with the batteries removed!
▶ Remove the battery.
▶ Never transport batteries in bulk form (loose, unprotected).
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
12 English 2235359
*2235359*
▶ Check the tool and batteries for damage before use after long periods of
transport.
Storage
CAUTION
Accidental damage caused by defective or leaking batteries !
▶ Always store your products with the batteries removed!
▶ Store the tool and batteries in a place that is as cool and dry as possible.
▶ Never store batteries in direct sunlight, on heating units or behind a
window pane.
▶ Store the tool and batteries in a place where they cannot be accessed by
children or unauthorized persons.
▶ Check the tool and batteries for damage before use after long periods of
storage.
9 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable
to remedy the problem by yourself, please contact Hilti Service.
Trouble or fault Possible cause Action to be taken
The power tool does
not work.
The battery is not fully
inserted.
▶ Insert the battery.
→ page 9
The control switch
cannot be pressed,
or is stuck.
The forward/reverse
selector switch is in the
middle position.
▶ Set the
forward/reverse
switch to the desired
position. → page 10
Running speed sud-
denly drops consid-
erably.
Low battery. ▶ Charge the battery.
→ page 9
The battery runs
down more quickly
than usual.
Very low ambient tem-
perature.
▶ Allow the battery to
warm up slowly to
room temperature.
The battery doesn’t
engage with an audi-
ble click.
The retaining lugs on the
battery are dirty.
▶ Clean the retaining
lugs and engage the
battery in the working
position.
The power tool or
the battery becomes
very warm.
Electrical fault. ▶ Switch the power
tool off immediately,
remove the battery,
keep it under obser-
vation, allow it to cool
down and contact
Hilti Service.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 English 13
Trouble or fault Possible cause Action to be taken
The power tool or
the battery becomes
very warm.
The tool is overloaded
(application limits ex-
ceeded).
▶ Select a suitable
power tool for the
application.
10 Disposal
Most of the materials from which Hilti tools and appliances are manu-
factured can be recycled. The materials must be correctly separated before
they can be recycled. In many countries, your old tools, machines or appli-
ances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti
representative for further information.
▶ Do not dispose of power tools, electronic equipment or batteries as
household waste!
11 Manufacturer’s warranty
▶ Please contact your local Hilti representative if you have questions about
the warranty conditions.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
14 Français 2235359
*2235359*
1 Indications relatives à la documentation
1.1 À propos de cette documentation
• Lire intégralement la présente documentation avant la mise en service.
C'est la condition préalablement requise pour assurer la sécurité du travail
et un maniement sans perturbations.
• Bien respecter les consignes de sécurité et les avertissements de la
présente documentation ainsi que celles figurant sur le produit.
• Toujours conserver le mode d'emploi à proximité du produit et uniquement
le transmettre à des tiers avec ce mode d'emploi.
1.2 Explication des symboles
1.2.1 Avertissements
Les avertissements attirent l'attention sur des dangers liés à l'utilisation du
produit. Les termes de signalisation suivants sont utilisés :
DANGER
DANGER !
▶ Pour un danger imminent qui peut entraîner de graves blessures corpo-
relles ou la mort.
AVERTISSEMENT
AVERTISSEMENT !
▶ Pour un danger potentiel qui peut entraîner de graves blessures corpo-
relles ou la mort.
ATTENTION
ATTENTION !
▶ Pour attirer l'attention sur une situation pouvant présenter des dangers
entraînant des blessures corporelles légères ou des dégâts matériels.
1.2.2 Symboles dans la documentation
Les symboles suivants sont utilisés dans la présente documentation :
Lire le mode d'emploi avant d'utiliser l'appareil
Pour des conseils d'utilisation et autres informations utiles
Maniement des matériaux recyclables
Ne pas jeter les appareils électriques et les accus dans les ordures
ménagères
1.2.3 Symboles dans les illustrations
Les symboles suivants sont utilisés dans les illustrations :
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
*2235359*
2235359 Français 15
Ces chiffres renvoient à l'illustration correspondante au début du
présent mode d'emploi
La numérotation détermine la séquence des étapes de travail dans
l'image et peut se différencier de celles des étapes de travail dans le
texte
Les numéros de position sont utilisés dans l'illustration Vue d’en-
semble et renvoient aux numéros des légendes dans la section Vue
d'ensemble du produit
Ce signe doit inviter à manier le produit en faisant particulièrement
attention.
1.3 Symboles spécifiques au produit
1.3.1 Symboles sur le produit
Les symboles suivants peuvent être utilisés sur le produit :
L'appareil prend en charge la technologie qui est compatible avec
les plates-formes iOS et Android.
Accu lithium-ions
Série de type d'accu Li-Ion Hilti utilisée. Observer les instructions au
chapitre Utilisation conforme à l'usage prévu.
Ne jamais utiliser l'accu comme outil de percussion.
Ne pas laisser tomber l'accu. Ne pas utiliser d'accu ayant subi un
choc ou d'autres dommages.
Courant continu
Vitesse de rotation de référence
Rotation droite
Rotation gauche
1.4 Informations produit
Les produits sont destinés aux professionnels et ne doivent
être utilisés, entretenus et réparés que par un personnel autorisé et formé.
Ce personnel doit être spécialement instruit quant aux dangers inhérents
à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer
dangereux s'ils sont utilisés de manière incorrecte par un personnel non
qualifié ou de manière non conforme à l'usage prévu.
La désignation du modèle et le numéro de série figurent sur sa plaque
signalétique.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
16 Français 2235359
*2235359*
▶ Inscrivez le numéro de série dans le tableau suivant. Les informations
produit vous seront demandées lorsque vous contactez nos revendeurs
ou services après-vente.
Caractéristiques produit
Type : SID 2-A12
Génération : 02
N° de série :
1.5 Déclaration de conformité
Nous déclarons sous notre seule et unique responsabilité que le produit
décrit ici est conforme aux directives et normes en vigueur. Une copie de
l'attestation délivrée par l'organisme de certification se trouve en fin de la
présente documentation.
Pour obtenir les documentations techniques, s'adresser à :
Hilti Entwicklungsgesellschaft mbH | Zulassung Geräte | Hiltistraße 6 | 86916
Kaufering, DE
2 Sécurité
2.1 Indications générales de sécurité pour les appareils électriques
AVERTISSEMENT Lire toutes les consignes de sécurité et instruc-
tions, illustrations et caractéristiques techniques, qui accompagnent
cet outil électroportatif. Tout manquement à l'observation des instruc-
tions suivantes risque de provoquer une électrocution, un incendie et/ou de
graves blessures.
Les consignes de sécurité et instructions doivent être intégralement
conservées pour les utilisations futures.
La notion d'« outil électroportatif » mentionnée dans les consignes de
sécurité se rapporte à des outils électriques raccordés au secteur (avec
câble d'alimentation) et à des outils électriques sur accu (sans câble
d'alimentation).
Sécurité sur le lieu de travail
▶ Conserver la zone de travail propre et bien éclairée. Un lieu de travail
en désordre ou mal éclairé augmente le risque d'accidents.
▶ Ne pas faire fonctionner les outils électriques en atmosphère ex-
plosive et où se trouvent des liquides, des gaz ou poussières in-
flammables. Les outils électriques produisent des étincelles qui peuvent
enflammer les poussières ou les fumées.
▶ Maintenir les enfants et les personnes présentes à l'écart pendant
l'utilisation de l'outil électroportatif. En cas d'inattention il y a risque de
perdre le contrôle de l'appareil.
Printed: 19.08.2019 | Doc-Nr: PUB / 5509360 / 000 / 00
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Hilti 2200201 Guide d'installation
- Catégorie
- Batteries rechargeables
- Taper
- Guide d'installation
dans d''autres langues
- español: Hilti 2200201 Guía de instalación
- português: Hilti 2200201 Guia de instalação
Documents connexes
-
Hilti 2109005 Manuel utilisateur
-
-
-
-
-
Hilti SD 5000-A22 Manuel utilisateur
-
Hilti C 4/12-50 Mode d'emploi
-
-
-