VTech DM111 Manuel utilisateur

Marque: VTech

Modèle: DM111

Catégorie: Babyphones

Taper: Manuel utilisateur

Note

• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and

should not be used as such.

Test your baby monitor

You may test the baby monitor before initial use, and at regular times thereafter.

Caution

• For hearing protection, make sure the parent

unit is more than 3 feet (1 meter) away from the

baby unit. If you hear any high-pitched noise,

move the parent unit further until the noise

stops. You can also press on the parent unit to

lower or mute the noise.

1. Make sure your baby unit and parent unit

are on.

2. Speak towards the microphone of the baby

unit. You will hear the sound at the parent unit,

and see the visual sound indicators light up.

Note

• When the POWER/LINK LED light ﬂashes, move the parent unit closer to the baby unit (observe

the minimum distance of 3 feet / 1 meter). You can also check if the baby unit is connected to a

live power socket and switched on.

Tip

• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the

baby unit.

Positioning the baby monitor

Caution

• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the

baby’s crib or playpen.

1. Place the baby units more than 3 feet (1 meter) away from

your baby.

2. Place the parent unit more than 3 feet (1 meter) away from the

baby unit to avoid screeching noise.

Caution

• The default volume of your parent unit is level 3, and the maximum

volume is level 5. If you experience high-pitched screeching noise from

your baby monitor while positioning:

- Make sure your baby units and parent unit are more than

3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit.

Operating range

The operating range of the baby monitor is up to

1000 feet (300 meters) outdoors or 160 feet (50

meters) indoors. The actual operating range may vary

depending on the environmental conditions and

other interferences such as walls, doors and other

obstructions.

DM111 / DM111-2

DM112 / DM112-2

Digital Audio Monitor

Go to www.vtechphones.com

to register your product for

enhanced warranty support and

the latest VTech product news.

Congratulations

on purchasing your new VTech product.

Before using this product, please read Important safety instructions.

This manual has all the feature operations and troubleshooting necessary to install and operate

your new VTech product. Please review this manual thoroughly to ensure proper installation and

operation of this innovative and feature-rich VTech product.

For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.

1 set for DM111 / DM112

2 sets for DM111-2 / DM112-2

1 Connect the baby monitor

What’s in the box

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 902.7 MHz - 927.1 MHz

Parent unit: 902.7 MHz - 927.1 MHz

Channels 62

Nominal effective range Maximum power allowed by FCC and IC. Actual operating range

may vary according to environmental conditions at the time of use.

Power requirements Baby unit adapter: Output: 6V DC @ 400mA

Parent unit adapter: Output: 6V DC @ 400mA

Parent unit battery: 2.4V NiMH battery

Technical specications

Speciﬁcations are subject to change without notice.

V22_900mhz

Power on or off the baby unit

• Press to turn on the baby unit. The POWER LED light turns

on.

• Press again to turn off the baby unit. The POWER LED light

turns off.

Power on or off the parent unit

• Press to turn on the parent unit. The

POWER / LINK LED light turns on.

• Press again to turn off the parent unit. The

POWER / LINK LED light turns off.

POWER POWER

Before use

Using the baby monitor

User’s manual DM111 DM112

For more support information

Important safety instructions

Install the parent unit battery

The parent unit runs on rechargeable battery or AC power. To continuously monitor your

baby, make sure you use both battery and AC power at the same time. With the battery

alone, the parent unit can cordlessly run for a short time only.

NOTESNOTE

• Use only the battery supplied with this product.

• If the parent unit will not be used for a long time, disconnect and remove the battery to prevent

possible leakage.

Replace the battery

To replace the battery, press down on the battery compartment cover and pull it out, then

follow the steps above to install the battery.

Connect the baby monitor

NOTESNOTE

• Use only the power adapters supplied with this product.

• Make sure the baby monitor is not connected to a switch controlled electric outlet.

• Connect the power adapters in a vertical or ﬂoor mount position only. The adapters’ prongs are not

designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,

or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children.

Charge the parent unit battery

When you have connected and turned on the baby unit and all the parent units, they will

enter pairing mode automatically. It takes around 10 minutes for the pairing process to

complete. When the parent unit and baby unit are successfully paired, both their power

LEDs are on steadily. The baby monitor is ready to use.

NOTESNOTE

Notes

• Before using the baby monitor for the ﬁrst time, charge the parent unit battery for 12 hours.

• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,

turn the parent unit off while charging.

• The standby time varies depending on the sensitivity level you set, your actual use and the age of the

battery.

• The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the battery is low.

harge the parent unit battery

without interruption

for at least 30 minutes.

• To keep the battery charged, connect it to AC power when not in use.

1 Connect the baby monitor (Cont’d)

POWER

> 3ft (1m)

3ft (1m)

POWER

> 3ft (1m)

3ft (1m)

POWER

> 3ft (1m)

The applied nameplate is located in the battery compartment of

the baby and parent units.

When using your equipment, basic safety precautions should

always be followed to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the baby unit at a height above 2

meters.

4. This product is not a substitute for adult supervision of the

infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and

therefore you should not assume it will continue working

properly for any given period of time. Further, this is not a

medical device and should not be used as such. This product

is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, do not use

it next to a bath tub, wash bowl, kitchen sink, laundry tub or

swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the batteries provided. There may be

a risk of explosion if a wrong type of battery is used for the

parent unit. The batteries cannot be subjected to high or low

extreme temperature and low air pressure at high altitude

during use, storage or transportation. Disposal of batteries

into ﬁre or a hot oven, or mechanically crushing or cutting or

the batteries can result in an explosion. Leaving the batteries

in an extremely high temperature surrounding environment

can result in an explosion or the leakage of ﬂammable liquid

of gas. Batteries subjected to extremely low air pressure may

result in an explosion or the leakage of ﬂammable liquid or

gas. Dispose of used battery according to the information

in The RBRC seal.

6. Use only the adapters included with this product. Incorrect

adapter polarity or voltage can seriously damage the

product.

7. Use only adaptors and batteries listed below.

Power adapter information:

Output: 6V DC 400mA

VTECH TELECOMMUNICATIONS LTD.

Model: VT05UUS06040

Rechargeable battery information:

2.4V NiMH battery

YIYANG CORUN BATTERY CO LTD.

Model: NI-MH AAA750*2

8. The power adapters are intended to be correctly oriented in a

vertical or ﬂoor mount position. The prongs are not designed

to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed

near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning.

Do not use liquid or aerosol cleaners. Use a damp cloth for

cleaning.

11. Unplug the power cords before replacing batteries.

12. Do not cut off the power adapters to replace them with other

plugs, as this causes a hazardous situation.

13. Do not allow anything to rest on the power cords. Do not

install this product where the cords may be walked on or

crimped.

14. This product should be operated only from the type of power

source indicated on the marking label. If you are not sure of

the type of power supply in your home, consult your dealer

or local power company.

15. Do not overload wall outlets or use an extension cord.

16. Do not place this product on an unstable table, shelf, stand

or other unstable surfaces.

17. This product should not be placed in any area where proper

ventilation is not provided. Slots and openings in the back

or bottom of this product are provided for ventilation.

To protect them from overheating, these openings must not

be blocked by placing the product on a soft surface such as a

bed, sofa or rug. This product should never be placed near

or over a radiator or heat register.

18. Never push objects of any kind into this product through

the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the

product.

19. To reduce the risk of electric shock, do not disassemble this

product, but take it to an authorized service facility. Opening

or removing parts of the product other than speciﬁed access

doors may expose you to dangerous voltages or other risks.

Incorrect reassembling can cause electric shock when the

product is subsequently used.

20. You should test the sound reception every time you turn on

the units or move one of the components.

21. Periodically examine all components for damage.

22. There is a very low risk of privacy loss when using certain

electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the

product has never been used before purchase, reset the baby

monitor periodically by powering off and then powering on

the units, and power off the baby monitor if you will not use

it for some time.

23. Children should be supervised to ensure that they do not

play with the product.

24. The product is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

1. Use and store the product at a temperature between 32oF

and 104oF.

2. Do not expose the product to extreme cold, heat or direct

sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as

bright sunshine or ﬁre.

4. Warning—Strangulation Hazard—Children

have STRANGLED in cords. Keep this cord out

of the reach of children (more than 3 ft (0.9 m)

away). Do not remove this tag.

5. Never place the baby unit inside the baby’s crib

or playpen. Never cover the baby unit or parent unit with

anything such as a towel or a blanket.

6. Other electronic products may cause interference with your

baby monitor. Try installing your baby monitor as far away

from these electronic devices as possible: wireless routers,

radios, cellular telephones, intercoms, room monitors,

televisions, personal computers, kitchen appliances and

cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent

research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted

cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the

pacemaker.

• Should NOT place wireless devices directly over the

pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with

pacemakers from other persons using wireless devices.

Electromagnetic ﬁelds (EMF)

This VTech product complies with all standards regarding

electromagnetic ﬁelds (EMF). If handled properly and

according to the instructions in this user’s manual, the product is

safe to be used based on scientiﬁc evidence available today.

CABLE MANAGEMENT

1 2 3

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby

monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install

and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is

paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging.

To keep this product working well and looking good, follow these guidelines:

• Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or

ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the baby unit and parent unit are dry before you connect them to the mains again.

When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the

adapters in a cool and dry place.

Below are the questions most frequently asked about the baby monitor. If you cannot ﬁnd the answer to your question,

visit our website at www.vtechphones.com, or contact 1 (800) 595-9511 for customer service.

Why doesn’t the POWER

light on the baby unit turn on

when I switch on the units?

Perhaps the baby unit is not connected to the power supply. Connect the baby unit to

power supply. The baby unit turns on.

Why doesn’t the POWER

/ LINK light on the parent

unit turn on when I switch

on the units?

Perhaps the battery of the parent unit is depleted and the parent unit is not connected

to power supply. Connect the parent unit to power supply and charge the parent unit

battery. The parent unit turns on and establishes connection with the baby unit.

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit.

2. Remove the battery from the parent unit.

3. Connect the baby unit to the power supply again. The baby unit turns on.

4. Connect the parent unit to the power supply again. The parent unit turns on.

5. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for

this to take place.

6. Press or to adjust the speaker volume on the parent unit.

Why does the baby

monitor produce a

high-pitched noise?

The parent units and baby unit may be too close to each other.

• Move the parent unit away from the baby units until the noise stops; OR

• Turn down the volume of your parent unit.

Why does the parent unit

beep?

The parent unit beeps three times every 30 seconds when the baby unit is out of range.

Move the parent units closer to the baby unit (but not less than 3 feet).

The parent unit may not have enough charge for the parent unit to perform normally.

Charge the battery in the parent unit for at least 30 minutes.

Why don’t I hear a sound/

Why can’t I hear my baby

cry?

Make sure that both baby unit and parent unit are on. If you see the visual sound indicators

light up, but there is no sound, then you may have muted the volume or set it to a lower

level. Adjust the volume to a higher level.

If the visual sound indicators do not light up, and you cannot hear any sound, it is because

the sound is too low for the baby unit to detect. This is normal. Place the baby unit at least

3 feet / 1 meter away from your baby.

Why does the light on

the parent unit ﬂash?

The parent unit beeps twice every 10 minutes and the light ﬂashes in red when the

battery is low. Connect the parent unit to the power supply and charge the battery for at

least 30 minutes.

Why can’t I establish a

connection? Why is the

connection lost every now

and then? Why are there

sound interruptions?

The baby unit may be out of range. Move the parent units closer to the baby unit (but not

less than 3 feet).

Other electronic products may cause interference with your baby monitor. Try installing

your baby monitor as far away from these electronic devices as possible.

Frequently asked questions

California Energy Commission battery

charging testing mode

General product care

Storage

Parent unit overview

1Visual sound indicators

The visual sound indicators can show

the sound level detected by the

baby unit or the volume level during

speaker volume setting.

Sound level detected by the baby

unit

•

One to three green lights indicate a

moderate sound level detected by

the baby unit.

•

Additional red lights indicate a

higher sound level detected by the

baby unit (e.g. baby crying loudly).

Speaker volume level

•

One to three green lights indicate

Level 1 to Level 3 of the speaker

volume setting.

•

Additional red lights indicate Level

4 to Level 5 of the speaker volume

setting.

2POWER / LINK

• Lights on steadily in green when

the parent unit is on and linked to

the baby unit.

• Flashes in green when there is no link

between the baby unit and parent

unit, or when the parent unit is out of

range from the baby unit.

• Steady on in red when the parent

unit is charging.

• Flashes in red when the battery is low.

4 (Volume down)

• Press to decrease the parent unit

speaker volume.

5Belt clip

6 (On/off)

• Press to turn on or off the parent

unit.

7Power jack

8 (Volume up)

• Press to increase the parent unit

speaker volume.

9Speaker

Parent unit alert tones

Low battery tone • Beeps twice every 10 minutes when the battery is low.

Out of range tone • Beeps three times every 30 seconds when there is no link

between the baby unit and parent unit, or when the parent

unit is out of range from the baby unit.

Adjust parent unit speaker volume

The speaker volume is preset to level 3, and the maximum

volume is level 5. You can adjust it to your preferred volume

level.

• Press or on the parent unit to adjust the speaker volume.

Note

• If you continue to press or when the volume reaches the

minimum or maximum setting, the parent unit will beep twice.

To mute the speaker volume:

• Press repeatedly until the volume reaches the minimum.

Notes

• When the parent unit is in mute, the visual sound indicator will still

indicate the sound detected from the baby unit.

• To unmute, press repeatedly until it reaches your desired volume.

1POWER light

• On steadily in green when the

baby unit is powered on.

• Off when the baby unit is

powered off.

2 (On/off)

• Press to turn on or off the baby

unit.

3Microphone

4Power jack

Baby unit overview

Using the baby monitor (Cont’d)

POWER

The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in

an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of

service within the United States and Canada.

The program provides a convenient alternative to placing used Ni-MH batteries into the trash or municipal

waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at

authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our

environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

The RBRC seal

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the

holder of a valid proof of purchase (“Consumer” or “you”)

that the Product and all accessories provided in the sales

package (“Product”) are free from defects in material

and workmanship, pursuant to the following terms and

conditions, when installed and used normally and in

accordance with the Product operating instructions. This

limited warranty extends only to the Consumer for Products

purchased and used in the United States of America and

Canada.

What will VTech do if the Product is not free from defects

in materials and workmanship during the limited warranty

period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized

service representative will replace at VTech’s option, without

charge, a Materially Defective Product. If we choose to

replace the Product, we may replace it with a new or

refurbished Product of the same or similar design. We will

retain defective parts, modules, or equipment. Replacement

of the Product, at VTech’s option, is your exclusive remedy.

VTech will return the replacement Products to you in

working condition. You should expect the replacement to

take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for

ONE (1) YEAR from the date of purchase (90 days on

products purchased as Refurbished*). This limited warranty

also applies to the replacement Product for a period of

either (a) 90 days from the date the replacement Product

is shipped to you or (b) the time remaining on the original

one-year warranty (90-day limited warranty on products

that are purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store

carry a 90-day replacement warranty.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident,

shipping or other physical damage, improper installation,

abnormal operation or handling, neglect, inundation,

ﬁre, water or other liquid intrusion; or

2. Product that has been damaged due to repair, alteration

or modiﬁcation by anyone other than an authorized

service representative of VTech; or

3. Product to the extent that the problem experienced is

caused by signal conditions, network reliability, or cable or

antenna systems; or

4. Product to the extent that the problem is caused by use

with non-VTech accessories; or

5. Product whose warranty/quality stickers, product serial

number plates or electronic serial numbers have been

removed, altered or rendered illegible; or

6. Product purchased, used, serviced, or shipped for repair

from outside the United States of America or Canada, or

used for commercial or institutional purposes (including

but not limited to Products used for rental purposes); or

7. Product returned without a valid proof of purchase (see

item 2 below); or

8. Charges for installation or set up, adjustment of customer

controls, and installation or repair of systems outside the

unit.

How do you get warranty service?

To obtain warranty service in the USA, please visit our

website at www.vtechphones.com or call 1 (800) 595-

9511. In Canada, go to www.vtechcanada.com or call

1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s

manual - a check of the Product’s controls and features may

save you a service call.

Except as provided by applicable law, you assume the risk

of loss or damage during transit and transportation and are

responsible for delivery or handling charges incurred in the

transport of the Product(s) to the service location. VTech

will return replaced Product under this limited warranty.

Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in

transit.

What must you return with the Product to get warranty

service?

1. Return the entire original package and contents

including the Product to the VTech service location along

with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt)

identifying the Product purchased (Product model) and

the date of purchase or receipt; and

3. Provide your name, complete and correct mailing

address, and telephone number.

Other limitations

This warranty is the complete and exclusive agreement

between you and VTech. It supersedes all other written or

oral communications related to this Product. VTech provides

no other warranties for this Product. The warranty exclusively

describes all of VTech’s responsibilities regarding the

Product. There are no other express warranties. No one is

authorized to make modiﬁcations to this limited warranty and

you should not rely on any such modiﬁcation. State/Provincial

Law Rights: This warranty gives you speciﬁc legal rights, and

you may also have other rights, which vary from state to state

or province to province.

Limitations: Implied warranties, including those of ﬁtness

for a particular purpose and merchantability (an unwritten

warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.

In no event shall VTech be liable for any indirect, special,

incidental, consequential, or similar damages (including,

but not limited to lost proﬁts or revenue, inability to use

the Product or other associated equipment, the cost of

substitute equipment, and claims by third parties) resulting

from the use of this Product. Some states/provinces

do not allow the exclusion or limitation of incidental

or consequential damages, so the above limitation or

exclusion may not apply to you.

Please retain your original sales receipt as proof

of purchase.

Limited warranty

FCC Part 15

This equipment has been tested and found to comply with

the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio commu-

nications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interfer-

ence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

WARNING: Changes or modiﬁcations to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation is

FCC and IC regulations

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use

of this user’s manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by

third parties that may arise through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

subject to the following two conditions: (1) this device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause

undesired operation.

This Class B digital apparatus complies with Canadian require-

ment:

CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s)

that comply with Innovation, Science and Economic Devel-

opment Canada’s licence-exempt RSS(s). Operation is subject

to the following two conditions: (1) This device may not cause

interference. (2) This device must accept any interference,

including interference that may cause undesired operation of

the device.

The term ‘’IC:‘’ before the certiﬁcation/registration number only

signiﬁes that the Industry Canada technical speciﬁcations were

met.

This product meets the applicable Innovation, Science and

Economic Development Canada technical speciﬁcations.

RF radiation exposure statement

Caution: To maintain compliance with the FCC’s RF exposure

guidelines, place the baby unit at least 20cm from nearby

persons. The device has been tested and complies with FCC

and IC SAR limits.

Mesures de sécurité importantes

La plaque signalétique appliquée se trouve dans le compartiment à

piles des unités bébé et parents.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines

mesures de précaution de base aﬁn de réduire les risques d’incendie,

d’électrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur

l’appareil.

2. L’installation par un adulte est requise.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du nourrisson.

La supervision du nourrisson est la responsabilité du parent ou

de la personne qui s’occupe de l’enfant. Ce produit pourrait

cesser de fonctionner et, par conséquent, vous ne devriez pas

présumer qu’il continuera de fonctionner correctement pendant

une période de temps donnée. De plus, il ne s’agit pas d’un

instrument médical et ne devrait pas être utilisé comme tel. Ce

produit est destiné à vous aider à superviser votre bébé.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre source

d’humidité, par exemple, près d’une baignoire, cuve à lessive,

évier de cuisine, dans un sous-sol humide ni près d’une piscine,

dans un soussol humide ou une douche.

6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque

d’explosion pourrait survenir si un mauvais type de pile est

utilisé pour l’unité du parent. La pile ne peut pas être soumise

à des températures extrêmes élevées ou basses et à une faible

pression d’air à haute altitude pendant l’utilisation, l’entreposage

ou le transport. L’élimination de la pile dans le feu ou dans un

four chaud, ou l’écrasement ou le découpage mécanique de

la pile peuvent entraîner une explosion. Laisser la pile dans

un environnement à température extrêmement élevée peut

entraîner une explosion ou la fuite d’un liquide ou d’un gaz

inﬂammable. Une pile soumise à une pression d’air extrêmement

basse peut provoquer une explosion ou une fuite de liquide ou

de gaz inﬂammable. Éliminer la pile usagée conformément aux

informations du Sceau RBRC.

7. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation

d’un adaptateur dont la polarité ou la tension serait inadéquate

risque d’endommager sérieusement le produit et mettre

Informations sur les adaptateurs électriques :

Sortie : 6V CC 400mA

VTECH TELECOMMUNICATIONS LTD.

Modèle : VT05UUS06040

Informations sur les piles rechargeables :

2.4V NiMH battery

YIYANG CORUN BATTERY CO LTD.

Modèle : NI-MH AAA750*2

8. Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches n’ont

pas été conçues pour supporter le poids du bloc d’alimentation

et le maintenir en place si celuici est branché dans une prise au

plafond, sous une table ou dans un meuble.

9. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la

prise de courant doit être installée près du produit, aﬁn d’assurer

une accessibilité sécuritaire à la prise de courant.

10. Débranchez ce produit de la prise de courant avant de procéder

au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un

chiffon humide pour le nettoyer.

11. Débranchez les cordons d’alimentation avant de remplacer le

bloc-piles.

12. Ne coupez pas les cordons d’alimentation pour remplacer les

ﬁches, car ceci peut présenter un danger potentiel.

13. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit où l’on

risque d’écraser le cordon d’alimentation ou de le piétiner.

14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation

indiqué sur l’étiquette. Si vous ne connaissez pas le type

d’alimentation que vous possédez à votre domicile, consultez

votre marchand ou votre compagnie locale d’électricité.

15. Ne surchargez pas les prises de courant murales ni les rallonges

électriques.

16. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

17. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil

ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de

surchauffer, ne bloquez sous aucun prétexte ces ouvertures et

n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur

un lit, divan, tapis ou toute autre surface similaire. De même, ne le

positionnez pas à proximité ni au-dessus d’une source de chaleur

ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit

avant de vous assurer qu’il y ait une bonne circulation d’air.

18. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

19. Aﬁn de réduire les risques d’électrocution, ne démontez pas cet

appareil, mais apportez-le dans un centre de service autorisé.

L’ouverture du boîtier ou le retrait de toutes pièces que contient

cet appareil, à l’exception de l’accès autorisé à certaines portes

ou ouvertures, risque de vous exposer à des points de tension

dangereux ou d’autres dangers. Un remontage incorrect peut par

la suite présenter des risques d’électrocution.

20. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

21. Examinez les composantes aﬁn de vériﬁer si celles-ci ne sont pas

endommagées.

22. Il existe un très faible risque de perte de conﬁdentialité avec

certains appareils électroniques (autres écoute-bébés, téléphones

sans ﬁls etc.). Pour l’éviter, s’assurer que le produit n’a jamais

été utilisé avant l’achat, réinitialiser l’unité de façon périodique,

éteindre l’écoute-bébé quand il n’est pas en cours d’utilisation.

23. Les enfants devraient être supervisés aﬁn de vous assurer qu’ils ne

jouent pas avec l’appareil.

24. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné sufﬁsamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚ C

(32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,

ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une

source de chauffage.

3. Le bloc-piles ne doit pas être exposé à la chaleur excessive telle

que la lumière du soleil ou au feu.

4. Avertissement - Risque de strangulation -

Les enfants se sont ÉTRANGLÉS dans des cordons.

Gardez ce cordon hors de portée des enfants (à

plus de 0,9 m). N’enlevez pas cette étiquette.

5. Ne jamais placer le moniteur à l’intérieur du

berceau ou du parc de bébé. Ne jamais couvrir le moniteur

ou l’unité (s) portative avec un article tel une serviette ou une

couverture.

6. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil, radios, téléphones

cellulaires, interphones, moniteurs, téléphones, ordinateurs

personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques

sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de

recherche indépendante, a mené une évaluation pluridisciplinaire des

interférences entre les téléphones sans fil portatifs et les stimulateurs

cardiaques implantés dans l’organisme. Appuyée par l’Administration

des aliments et drogues (FDA) des États-Unis, la firme WTR

recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six pouces

du simulateur cardiaque.

• Ils ne doivent PAS placer le téléphone sans fil directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque

pour les détenteurs de simulateurs cardiaques causés par les gens qui

utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant

aux champs électromagnétiques (EMF) standard. Si vous le manipulez

correctement en suivant les instructions de ce guide, son utilisation

sera sécuritaire pendant de nombreuses années, selon les meilleures

évidences scientifiques dont nous disposons aujourd’hui.

For cETL compliance only

VTech DM111 Manuel utilisateur

Marque: VTech

Modèle: DM111

Catégorie: Babyphones

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: VTech DM111 User manual

VTech DM111 Manuel utilisateur

VTech DM111 Manuel utilisateur

dans d''autres langues

Documents connexes