Modern Forms FR-W2001 Renegade 66 Mode d'emploi

Renegade

Installation Instructions

works with the

Google Assistant

FR-W2001

Renegade Instructions2

Please read and

save these instructions

before installation

DO NOT RETURN TO STORE

FR-W2001 Renegade Instructions 3

General Inquiries

For all questions about your ceiling fan please read all included

instructions, installation procedures, troubleshooting guidelines

and warranty information before starting installation.

For missing parts or general inquiries call our trained technical staﬀ at:

1-866-810-6615 option 1

MON-FRI 8AM-8PM EST

Email:

customerservice@modernforms.com

Or live chat at modernforms.com

Fan Support

For fast service have the following information below when you call:

1. Model Name and Number

2. Part Number and Part Description

3. Date Of Purchase and Purchase Location

1-866-810-6615 option 2

MON-FRI 8AM-8PM EST

Email:

fansupport@modernforms.com

FR-W2001

Renegade Instructions4

For operation, maintenance, and troubleshooting information,

visit http://modernforms.com/fan-support/

To reduce the risk of electric shock, ensure electricity has been turned oﬀ at the circuit breaker

before beginning. All wiring must be in accordance with the National Electrical Code “ANSI/NFPA

70” and local electrical codes. Electrical installation should be performed by a licensed electrician.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from the trailing edge of

the fan blades to the floor and a minimum of 1.5 ft (0.5m) from the edge of the fan blades to the

surrounding walls. Never place objects in the path of the fan blades. To avoid personal injury or

damage to the fan and other items, please be cautious when working around or cleaning the fan.

To avoid electrical shock or damage to the motor or ﬁnish, do not use water or chemicals

when cleaning the fan or fan blades. A dry cloth or lightly dampened cloth will be suitable

for most cleaning.

After making electrical connections, spliced conductors should be turned upward and pushed

carefully up into the outlet box. The wires should be spread apart with the grounded conductor and

the equipment-grounding conductor on one side of the outlet box, and the ungrounded conductor

on the other side of the outlet box.

All set screws must be checked and re-tightened

where necessary before installation.

Safety Rules

FR-W2001 Renegade Instructions 5

WARNING: Do not install or use your fan if any part(s) is/are damaged or missing. This product

is designed for use only with the supplied parts and/or accessories designated for use with this

product by Modern Forms. Substitution of parts or accessories not designated for use with this

product by Modern Forms could result in personal injury or property damage and will void the

warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

WARNING: To reduce the risk of electric shock, this fan must

be installed and operated with the supplied wall control, or controlled from the Modern Forms app

or Wi-Fi Touch Panel Wall Control (not included).

WARNING: Do not use power tools to assemble or install your fan. Using power tools can result in

improper assembly which can lead to noise or fan damage,personal injury or property damage.

WARNING: To reduce the risk of personal injury, do not bend the blade arms when installing the

brackets, balancing the blades or cleaning the fan.

WARNING: Do not insert foreign objects between rotating fan blades.

WARNING: Do not operate fan unless fan blades are in place. Noise and fan damage can occur

WARNING: This appliance is not intended for use by young children without supervision.

WARNING: To reduce the risk of ﬁre, electric shock, personal injury or damage to the fan or other

items, the outlet box and support structure must be securely mounted and capable of reliably

supporting a minimum of 35 Ibs (15.9 kg). Use only UL/cUL listed outlet boxes marked “FOR FAN

SUPPORT.” Use only the screws and washers provided with the outlet box.

CAUTION: Before assembling your fan, refer to the “Making the Electrical Connections“

section. If you feel you do not have enough wiring knowledge or experience, have your fan

installed by a licensed electrician.

NOTE: Before servicing or cleaning the fan, switch power oﬀ at the circuit breaker.

FR-W2001

Renegade Instructions6

Get Smart...

Integrates

seamlessly with:

devices you already own

works with the

Google Assistant

Premium smart

features:

Accessories:

DC

MOTOR

complement high quality materials

personalize your experience

Quiet, reliable, and up to 70%

more ecient than AC fans

Wi-Fi and Bluetooth enabled

for exible control

Bluetooth Wall Control

Dims light to 1% | ON/OFF

6 fan speeds | Sold separately

F-WCBT-WT White

Bluetooth Remote Control

Dims light to 1% | ON/OFF

6 fan speeds

F-RCBT-WT White

Wet Location-listed to the strictest

UL/cUL safety regulations. Finished

and rated for interior and exterior use

FR-W2001 Renegade Instructions 7

Contents

Tools Required

1. Mounting Options 10

2. Installing the Mounting Bracket 12

3. Attaching the Fan Blade/Arms 12

3A. Attaching the Brush Nickel Blade/Arms 12

4. Hanging the Fan 14

5. Making the Electrical Connections 16

6. Installing the Wall Control (Optional) 18

7. Finishing the Installation 20

8. Installing the Luminaire Module 20

9. Controlling the Fan 22

10. Factory Reset 24

11. Breeze Mode 24

12. Application 24

13. Accessories 26

14. Troubleshooting 28-30

FR-W2001

Renegade Instructions8

Package Contents

7. Adapter Plate

8. Luminaire Module

F4IN-120V-R1-30

9. Luminiare Cover

RPL-F2001-COVER-**

10. Luminiare Glass

RPL-F2001-GLA

11. Control Receiver

w/Hardware

F-R3-2001-0**

12. Remote Control

F-RCBT-WT

Hardware Bag

RPL-F2001-PARTS

1. Blade Set of 8

RPL-F2001-*-BD-**

2. Blade Arms Set of 8

3. Downrod Assembly

Mounting Bracket

RPL-HGR-ASM-6-**

4. Canopy & Canopy

Screw Ring

RPL-CAN-CYL-**

5. Coupling Cover

6. Motor Asssembly

** Denotes ﬁnish code of fan/blade sweep of fan

Non-Brushed Nickel ﬁnishes come with diﬀerent blade arms, no decorative screw nuts

Decorative screw nuts come with brushed nickel ﬁnishes in the hardware bag

Before discarding packaging materials be certain all parts have been removed.

Place the parts from the hardware bag into a small container to keep them from being lost.

2

1

2

AMachine Screws (2)

Spring Washers (2)

Flat Washers (2)

BScrews and Nylon Washers (25/25)

CBlade Arm Screws

1/4” x 1/2” (16)

D

Wood Screw (1)

Spring Washer (1)

Flat Washer (1)

EWire Nuts (11)

2A.

2B.

RPL-F-2001-BARM-**

RPL-F-2001-BARM2-**

FR-W2001 Renegade Instructions 9

Non-Brushed Nickel ﬁnishes come with diﬀerent blade arms, no decorative screw nuts

24x Decorative screw nuts come with Brushed Nickel ﬁnishes located in the hardware bag

MAC ID

12

5

8

9

10

11

6

7

3

4

Hanging Weight: 35 lbs

IMPORTANT: Please make note of

the MAC ID on the receiver and

keep it in a safe place.

2A

2B

1

FR-W2001

Renegade Instructions10

1. Mounting Options

CAUTION: To prevent electrical shock, ensure electricity has been

turned oﬀ at the circuit breaker before beginning.

If there isn’t an existing UL/cUL listed outlet box, please refer to the

following instructions. Secure the outlet box directly to the building

structure. Use appropriate fasteners and building materials. The

outlet box and support structure must be able to fully support the

moving weight of the fan (at least 35 lbs/15.9 kg). Do not use plastic

outlet boxes. Use only UL/cUL listed outlet boxes marked

“FOR FAN SUPPORT.”

Secure the outlet box directly to the building structure.

Use appropriate fasteners and building materials. The outlet box

and its support must be able to fully support the moving weight

of the fan (at least 35 lbs). Do not use plastic outlet boxes.

Figures 1-1C are examples of diﬀerent ways to mount the

outlet box.

NOTE: To hang your fan where there is an existing ﬁxture but no

ceiling joist, you may need an installation hanger bar.

NOTE: Downrod fans can be suspended up to a maximum

recommended length of 72” using additional downrods

(sold separately) and the included 80” lead wire.

NOTE: The sloped ceiling kit (sold separately) is required for sloped

ceiling applications, and will accommodate slopes up to 45° (Fig. 1B).

NOTE: You may need a longer downrod to maintain proper blade

clearance when installing on a steep, sloped ceiling (Fig. 1B).

FR-W2001 Renegade Instructions 11

1

1A

1B

1C

1

2

1

2

3

1. Support Brace

2. Outer Box

3. Joist

1. Support Brace

2. Mounting Bracket

3. Recess Outlet Box

1. Outlet Box

1. Outer Box

Support Ceiling

Max 30° Angle

FR-W2001

Renegade Instructions12

3. Attaching the Fan Blades/Blade Arms

3A. Attaching the Fan Blades/Blade Arms (Brushed Nickel)

2. Installing the Mounting Bracket

Remember to disconnect the power at the circuit breaker.

1. Remove 1 of 2 screws from the bottom of the mounting bracket

and save for use in section 11. Loosen the other screw (Fig. 2).

2. Pass the 120-volt supply wires through the center hole in the

mounting bracket as shown (Fig. 2A).

3. Secure the mounting bracket to the ceiling outlet box with the

screws and washers provided with your outlet box. Use Part A if

needed

4. Before you install the blades/blade arms - remove and discard

the rubber motor stops from the motor housing.

NOTE: Make sure that mounting screws are tight.

1. Attach the blade to blade arm using the screws and washers as

shown in (Fig. 3). Use Part B.

2. Fasten blade/blade arm to the motor housing using the supplied

screws to motor using screws supplied (Fig.3). Use Part C.

1. Lay the side of the blade holder on a flat surface with the inside

of the blade holder facing up. Attach the blade to the blade holder

with the decorative screw nuts, flat washers, and screws. Make

sure to tighten screws. Use Part B. (Decorative screw nuts are

located in the hardware bag).

2. Attach assembled blades and blade holders to the motor housing

using the provided screws with lock washers. Make sure the

screws securing the blade holders to the motor housing are on

tight. (Fig. 3B) Use Part C.

(Brushed nickel version comes included with diﬀerent blade arms and decorative wire nuts. Skip to 3A if

you ordered the Brushed Nickel version of this fan.)

FR-W2001Renegade Instructions 13

3 3A

3B

2 2A

1. Mounting Bracket

2. Screw

1

2

3

1

To Switch A

A

B

(HOT)

(Neutral)

(HOT)/

Switch

(No Neutral)

(Ground)

*Bare or Green

(Ground)

*Bare or Green

To Switch

1. cUL Listed Electrical Box

2. Mounting Screws

(outlet box screws not included)

3. 120V Wires

For Brushed Nickel version

1

Decorative Screw Nuts

FR-W2001

Renegade Instructions14

1. Remove screw from hanger ball. Remove hanger ball

and cross pin.

2. Loosen 2 screws, clevis pin and cotter pin (Fig. 4A).

3. Install coupling cover, canopy screw ring, canopy and downrod

assembly into motor housing as shown (Fig. 4).

4. Align downrod and motor collar holes, re-insert pins and screws

(Fig. 4B).

5. Slip up canopy and canopy screw cover. Re-install hanger ball with

cross pin in correct place (Fig. 4).

6. Seat all into the mounting bracket. Rotate until ball drops and locks

into hanger bracket screw (Fig. 4A).

7. Secure the safety cable into the structure beams using the wood

screw, washers, and spring washers provided (Fig. 4B). Use Part D.

NOTE: Safety cable is required for all ceiling fan installations in Canada.

Safety cable is required for ceiling fan and light (combo) installations

over 35 lbs. in both flush and downrod models in the United States.

4. Hanging the Fan

FR-W2001 Renegade Instructions 15

4B

4 4A

FR-W2001

Renegade Instructions16

5. Making the Electrical Connections

WARNING: Installation of this fan requires that a three-conductor

cable (including ground wire) which should run between ceiling and

wall outlet box.

WARNING: Check to see that all connections are tight, including

ground, and that no bare wire is visible at the wire nuts,

except for the ground wire.

Insert the receiver into the mounting bracket with the flat side of the

receiver facing the ceiling (Fig. 5).

Motor to Receiver & Receiver to housing supply wires (Fig. 5A).

Use Part E.

1. Connect the hanger ball/downrod assembly ground wire,

mounting bracket ground wire and receiver ground wire to

the ground wire in outlet box.

WARNING: Failure to connect ground wires could result in

poor fan control functionality.

2. Connect the red wire from the fan to the red wire marked

“TO MOTOR” from the receiver.

3. Connect the grey wire from the fan to the grey wire marked

“TO MOTOR” from the receiver.

4. Connect the yellow wire from the fan to the yellow wire marked

“TO MOTOR” from the receiver.

5. Connect the white wire from the fan to the white wire marked

“FOR LIGHT” from the receiver.

6. Connect the blue wire from the fan to the blue wire marked

“FOR LIGHT” from the receiver.

7. Connect the black (hot) wire from the ceiling to the black wire

marked “AC in L” from the receiver.

8. Connect the white (neutral) wire from the ceiling to the white

wire marked “AC in N” from the receiver.

FR-W2001 Renegade Instructions 17

Follow the steps above to connect the fan to your household wiring. Use the plastic wire nuts with your fan.

Secure the plastic wire nuts with electrical tape. Make sure there are no loose strands or connections.

Use Part E.

5

5A

Black(Hot)

can be RED from Switch leg

Black(Line in H)

RED(to Motor)

GREEN(Ground)

BLUE (to Light)

BLUE (for Light)

GREEN(GND Must Use)

GREEN(Hanger Bracket Ground)

RED(to Motor)

GREY(to Motor)

WHITE(Neutral)

WHITE(to Light)

WHITE(Neutral)

Safety Cable

GREY(to Motor)

YELLOW(to Motor)

WHITE(Line in N)

YELLOW(to Motor)

Outlet

Box

Receiver

Hanger Ball & Downrod

Hanger

Bracket

1

2

1. Mounting Bracket

2. Receiver

FR-W2001

Renegade Instructions18

6. Installing the Wall Control (Optional)

NOTE: Wall Control not included. A bluetooth wall control accessory

can be purchased separately.

1. Connect the green wire marked “GROUND” from the wall

control to the copper wire from the wall outlet box that

feeds back to the circuit breaker – important for proper

fan function (Fig. 6).

2. Connect the black wire marked “LINE IN” from the wall control to

the black LINE VOLTAGE wire from the wall outlet box that feeds

back to the circuit breaker (Fig. 6).

3. Connect the red wire from the wall control to the black wire from

the wall outlet box that feeds up to the fan (Fig. 6).

4. Connect the white wire from the wall control to the white

(neutral) wire from the wall outlet box (Fig. 6).

5. Carefully tuck the wire connections inside the outlet box.

Secure the wall control with the two (2) wall control screws

provided (Fig. 6A).

6. Attach the wall mounting plate over the wall switch and secure

with the two (2) wall mounting plate screws provided (Fig. 6A).

7. Fasten the wall plate to the wall mounting plate (Fig. 6A).

6

Wall Switch WiresHouse Wires

(Hot In)

(Neutral)

(Ground)

(Hot out to Fan)Fan Switch leg

(Copper/Ground)

(Neutral)

(Hot)

From Breaker

* Home Wiring may vary

to Fan

FR-W2001 Renegade Instructions 19

6A

Multi-location wiring

1 2 3

54

1. Wall Outlet

2. Wall Control

3. Wall Mounting Plate

4. Mounting Plate Screws

5. Wall Plate

Individually pair each of the wall controls with the fan

receiver using the pairing instruction. See page 25.

Line/Hot

Red

Green (Green or Bare)

Wall Controller 1 Wall controller 2 Wall Controller 3

If Applicable

FAN

Neutral/White

FR-W2001

Renegade Instructions20

7. Finishing the Installation

1. Secure wire connectors with supplied wire ties.

2. Install canopy to mounting bracket with the screw

removed in section 4 (Fig. 7).

3. Install canopy screw ring as shown (Fig. 7).

8. Installing the Luminaire Module

Installation of the Luminaire (Glass/Cover) is optional.

NOTE: Skip to step 6 if you are not installing the

(Glass Shade/LED module).

1. Remove 1 of 3 screws and loosen the others

(DO NOT REMOVE) from the motor assembly (Fig. 8).

2. Twist-lock the adapter plate into place.

3. Attach LED wires from motor assembly to luminaire module.

Blue from fan to blue from luminaire module and white from

fan to white from luminaire module (Fig. 8).

4. Secure the luminaire module with the 3 screws to the

adapter plate (Fig. 8).

5. Install Glass Shade without over-tightening (Fig. 8A/8B).

6. Install Metal Light cover as shown (Fig. 8A/8B).

NOTE: Add metal light cover if you do not need lighting function

or prefer a diﬀerent aesthetic.

NOTE: Do not connect the LED module if you are using the

metal light cover.

La page charge ...

Modern Forms FR-W2001 Renegade 66 Mode d'emploi

Ce manuel convient également à

Modern Forms FR-W2001 Renegade 66 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents