Kenwood DPX305MBT Guide d'installation

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

For your records

Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the model and serial

numbers whenever you call upon your Kenwood dealer for information or service on the product.

Model DPX395MBT/DPX305MBT

Serial number

US Residents Only

Register Online

Register your Kenwood product at https://www.kenwood.com/usa/

DPX395MBT

DPX305MBT

DUAL DIN SIZED DIGITAL MEDIA RECEIVER

INSTRUCTION MANUAL

AUTORADIO MULTIMÉDIA NUMÉRIQUE DEUX DIN

MODE D’EMPLOI

RECEPTOR DE MEDIOS DIGITALES TAMAÑO DOBLE DIN

MANUAL DE INSTRUCCIONES

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd 1DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd 1 7/5/2021 4:34:08 PM7/5/2021 4:34:08 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

i

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that interference will not occur

in a particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

– Consult the dealer or an experienced radio/TV technician for help.

Información acerca de la eliminación de equipos eléctricos y electrónicos al final de la vida

útil (aplicable a los países que hayan adoptado sistemas independientes de recogida de

residuos)

Los productos con el símbolo de un contenedor con ruedas tachado no podrán ser

desechados como residuos domésticos. Los equipos eléctricos y electrónicos al final

de la vida útil, deberán ser reciclados en instalaciones que puedan dar el tratamiento

adecuado a estos productos y a sus subproductos residuales correspondientes.

Póngase en contacto con su administración local para obtener información sobre el

punto de recogida más cercano. Un tratamiento correcto del reciclaje y la eliminación

de residuos ayuda a conservar los recursos y evita al mismo tiempo efectos

perjudiciales en la salud y el medio ambiente.

Supplier's Declaration of Conformity

Trade Name: KENWOOD

Products: DUAL DIN SIZED DIGITAL MEDIA RECEIVER

Model Name: DPX395MBT/DPX305MBT

Responsible Party: JVCKENWOOD USA CORPORATION

4001 Worsham Avenue, Long Beach, CA 90808, U.S.A.

PHONE: 1-800-252-5722

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING

TWO CONDITIONS:

(1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

ISED Caution

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science

and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two

conditions:

1. This device may not cause interference.

2. This device must accept any interference, including interference that may cause undesired

operation of the device.

Attention de ‘ISED

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR

d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts

de licence. L’exploitation est autorisée aux deux conditions suivantes :

1. L’appareil ne doit pas produire de brouillage.

2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

DPX395MBT_K_B5A-3890-00_Cover_5th Draft.indd iDPX395MBT_K_B5A-3890-00_Cover_5th Draft.indd i 1/11/2022 1:53:04 PM1/11/2022 1:53:04 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

ii

Contains Bluetooth Module FCC ID: ZWY88112

IC ID: 12033A-88112

This transmitter must not be co-located or operated in conjunction with any other antenna or

transmitter.

CAUTION

This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled

environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio

frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at

least 20 cm or more away from person’s body.

ATTENTION

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un

environnement non contrôlé et respecte les règles les radioélectriques (RF) de la FCC lignes directrices

d’exposition et d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’ISED. Cet équipement

doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps

humain.

Para cumplimiento de la IFT:

“La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada”

SOFTWARE LICENSE AGREEMENT

The software embedded in the Product (hereinafter the "Licensed Software") provided by Licensor is

copyrighted to or sublicensable by the Licensor, and this Agreement provides for the terms and conditions

which Users shall follow in order to use the Licensed Software.

The User shall use the Licensed Software by agreeing with the terms of this Software License Agreement.

This Agreement shall be deemed completed at the time the User (hereinafter the "User") initially used the

Product in which the "Licensed Software" is embedded.

The Licensed Software may include the software which has been licensed to the Licensor directly or

indirectly from any third party. In such case, some third parties require the Users to follow their conditions

for use separately from this Software License Agreement. Such software shall not be subject to this

Agreement, and the Users are urged to read the "Important Notice concerning the Software" to be provided

separately below.

Article 1 General Provision

The Licensor shall grant to the User a non-exclusive and non-transferable (other than the exceptional case

referred to in Article 3, Paragraph 1) licensed to use the Licensed Software within the country of the User.

(the country where the User bought the Product (hereinafter the "Country")

Article 2 License

1. The license granted under this Agreement shall be the right to use the Licensed Software in the

Product.

2. The User shall not duplicate, copy, modify, add, translate or otherwise alter, or lease the Licensed

Software and any related documents, whether in whole or in part.

3. The use of the Licensed Software shall be limited to personal purpose, and the Licensed Software shall

not be distributed, licensed or sub-licensed whether it is for commercial purpose or not.

4. The User shall use the Licensed Software according to the directions described in the operation

manual or help file, and is prohibited to use or duplicate any data in a manner violating the Copyright

Law or any other laws and regulations by applying whole or a part of the Licensed Software.

Article 3 Conditions for Grant of License

1. When the User transfers the Product, it may also transfer the license to use the Licensed Software

embedded in the Product (including any related materials, updates and upgrades) on condition that

no original, copies or related materials continue in the possession of the User, and that the User shall

cause the transferee to comply with this Software License Agreement.

2. The User shall not carry out reverse engineering, disassembling, decompiling or any other code

analysis works in connection with the Licensed Software.

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd iiDPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd ii 7/5/2021 4:34:12 PM7/5/2021 4:34:12 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

iii

Article 4 Right pertaining to the Licensed Software

Any and all copyrights and other rights pertaining to the Licensed Software and related documents

shall belong to the Licensor or the original holder of the right who granted to the Licensor the license or

sublicense for the Licensed Software (hereinafter the "Original Rightholder"), and the User shall not be

entitled to any right other than the license granted hereunder, in respect of the Licensed Software and any

related documents.

Article 5 Indemnification of Licensor

1. Neither the Licensor nor the Original Rightholder shall be liable for any damage incurred by the User

or any third party due to the exercise of the license granted to the User under this Agreement, unless

otherwise restricted by law.

2. The Licensor will offer no guarantee for the merchantability, convertibility and consistency with

certain objective of the Licensed Software.

Article 6 Liability to Third Party

If any dispute has arisen with any third party due to an infringement upon a copyright, patent or any

other intellectual property right that was caused by the User's use of the Licensed Software, the User shall

settle such dispute at its own cost and hold the Licensor and the Original Rightholder harmless from any

inconvenience it may cause.

Article 7 Confidentiality

The User shall keep the confidentiality of such portion of the Licensed Software, related documents thereof

or any other information to be granted under this Agreement, as well as the conditions of this Agreement

as has not yet entered the public domain, and shall not disclose or divulge the same to any third party

without approval of the Licensor.

Article 8 Termination

In case the User falls under any of the events described in the following items, the Licensor may

immediately terminate this Agreement or claim that the User compensates for the damage incurred by the

Licensor due to such event:

(1) when the User violated any provision of this Agreement; or

(2) when a petition has been filed against the User for an attachment, provisional attachment,

provisional disposition or any other compulsory execution.

Article 9 Destruction of the Licensed Software

If this Agreement is terminated pursuant to the provision of Article 8, the User shall destroy the Licensed

Software, any related documents and copies thereof within two (2) weeks from such date of termination.

Article 10 Protection of Copyright

1. The copyright and all the other intellectual property rights relating to the Licensed Software

shall belong to the Licensor and the Original Rightholder, and in no event shall they be under the

ownership of the User.

2. The User shall, whenever it uses the Licensed Software, comply with any laws relating to the

copyright and other intellectual property rights.

Article 11 Export Restriction

1. It is prohibited to export the Licensed Software and any related documents outside the country

of the User (including transmission thereof outside the country of the User via Internet of other

communication tools).

2. The User shall understand that the Licensed Software shall be subject to the export restrictions

adopted by the country of User and any other countries.

3. The User shall agree that the software will be subject to any and all applicable international and

domestic laws (including the export control regulation of the country of User and any other countries,

and any restrictions concerning the end-users, the use by end-users and importing countries to be

provided by the country of User and any other countries, and any other governmental authorities).

Article 12 Miscellaneous

1. In the event any part of this Agreement is invalidated by operation of law, the residual provisions

shall continue in force.

2. Matters not stipulated in this Agreement or any ambiguity or question raised in the construction of

this Agreement shall be provided or settled upon good-faith consultation between the Licensor and

the User.

3. The Licensor and the User hereby agree that this Agreement is governed by the laws of Japan, and

any dispute arising from, and relating to the rights and obligations under, this Agreement shall be

submitted to the exclusive jurisdiction of the Tokyo District Court for its first instance.

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd iiiDPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd iii 7/5/2021 4:34:12 PM7/5/2021 4:34:12 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

iv

Important Notice concerning the Software

-jansson

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

-cJSON

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

-CMP

The MIT License (MIT)

Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated

documentation files (the "Software"), to deal in the Software without restriction, including without

limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the

Software, and to permit persons to whom the Software is furnished to do so, subject to the following

conditions:

The above copyright notice and this permission notice shall be included in all copies or substantial portions

of the Software.

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

nanopb

This software is provided 'as-is', without any express or implied warranty. In no event will the authors be

held liable for any damages arising from the use of this software.

Permission is granted to anyone to use this software for any purpose, including commercial applications,

and to alter it and redistribute it freely, subject to the following restrictions:

1. The origin of this software must not be misrepresented; you must not claim that you wrote

the original software. If you use this software in a product, an acknowledgment in the product

documentation would be appreciated but is not required.

2. Altered source versions must be plainly marked as such, and must not be misrepresented as being the

original software.

3. This notice may not be removed or altered from any source distribution.

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd ivDPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd iv 7/5/2021 4:34:12 PM7/5/2021 4:34:12 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

v

sha2

AUTHOR: Aaron D. Gifford - http://www.aarongifford.com/

You may obtain a copy of the license at

https://opensource.org/licenses/BSD-3-Clause

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Posix

Redistribution and use in source and binary forms, with or without modification, are permitted provided

that the following conditions are met:

1. Redistributions of source code must retain the above copyright notice, this list of conditions and the

following disclaimer.

2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and

the following disclaimer in the documentation and/or other materials provided with the distribution.

3. All advertising materials mentioning features or use of this software must display the following

acknowledgement:

This product includes software developed by the University of California, Berkeley and its contributors.

4. Neither the name of the University nor the names of its contributors may be used to endorse or

promote products derived from this software without specific prior written permission.

Developed at SunPro, a Sun Microsystems, Inc. business.

Permission to use, copy, modify, and distribute this software is freely granted, provided that this notice is

preserved.

License to copy and use this software is granted provided that it is identified as the “RSA Data Security, Inc.

MD4 Message-Digest Algorithm” in all material mentioning or referencing this software or this function.

Author: Chris G. Demetriou

Permission to use, copy, modify and distribute this software and its documentation is hereby granted,

provided that both the copyright notice and this permission notice appear in all copies of the software,

derivative works or modified versions, and any portions thereof, and that both notices appear in supporting

documentation.

CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" CONDITION. CARNEGIE MELLON

DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF

THIS SOFTWARE.

Carnegie Mellon requests users of this software to return to

Software Distribution Coordinator or [email protected]

School of Computer Science

Carnegie Mellon University

Pittsburgh PA 15213-3890

any improvements or extensions that they make and grant Carnegie the rights to redistribute these

changes.

License is also granted to make and use derivative works provided that such works are identified as

"derived from the RSA Data Security, Inc. MD4 Message-Digest Algorithm" in all material mentioning or

referencing the derived work.

RSA Data Security, Inc. makes no representations concerning either the merchantability of this software or

the suitability of this software for any particular purpose. It is provided "as is" without express or implied

warranty of any kind.

You may redistribute unmodified or modified versions of this source code provided that the above

copyright notice and this and the following conditions are retained.

This software is provided ``as is'', and comes with no warranties of any kind. I shall in no event be liable for

anything that happens to anyone/anything when using this software.

These notices must be retained in any copies of any part of this documentation and/or software.

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd vDPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd v 7/5/2021 4:34:12 PM7/5/2021 4:34:12 PM

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

vi

T-Kernel 2.0

This product uses the source code of T-Kernel 2.0 under T-License 2.0 granted by T-Engine Forum

(www.tron.org)

BSD-3-Clause

You may obtain a copy of the license at

https://opensource.org/licenses/BSD-3-Clause

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

LFS Subsystem

You may obtain a copy of the license at

https://directory.fsf.org/wiki/License:BSD-4-Clause

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

Accordo2 Player

Apache License

Licensed under the Apache License,

Version 2.0, January 2004(the "License");

You may obtain a copy of the license at

http://www.apache.org/licenses/LICENSE-2.0

THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING

BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND

NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,

DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING

FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.

DPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd viDPX395MBT_K_B5A-3890-00_Cover_1st Draft.indd vi 7/5/2021 4:34:12 PM7/5/2021 4:34:12 PM

2ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Contents

Before Use ................................................................................................. 3

Basics ......................................................................................................... 3

Getting Started ........................................................................................ 4

1 Select the display language and cancel the demonstration

2 Set the clock and date

3 Set the other optional settings

Radio .......................................................................................................... 6

USB/iPod ................................................................................................... 8

SiriusXM® Radio ..................................................................................... 11

AUX........................................................................................................... 14

KENWOOD Remote Application ......................................................... 14

Bluetooth® .............................................................................................. 15

Bluetooth – Connection

Bluetooth – Mobile phone

Bluetooth – Audio

AMAZON ALEXA .................................................................................... 21

Audio Settings ........................................................................................ 24

Display Settings ..................................................................................... 27

Installation/Connection ....................................................................... 28

References .............................................................................................. 32

Maintenance

More information

Change the display information

Troubleshooting .................................................................................... 34

Specifications ......................................................................................... 37

How to read this manual

• The displays and faceplates shown in this manual are examples used to

provide clear explanations of the operations. For this reason, they may

be different from the actual displays or faceplates.

• Operations are explained mainly using buttons on the faceplate of

.

• English indications are used for the purpose of explanation. You can

select the display language from the

[FUNCTION]

menu. (Page6)

•

[XX]

indicates the selected items.

• (PageXX) indicates references are available on the stated page.

This symbol on the product means there are important

operating and maintenance instructions in this manual.

Be sure to carefully read instructions in this manual.

DPX395MBT_K_B5A-3890-00_EN_5th Draft.indd 2DPX395MBT_K_B5A-3890-00_EN_5th Draft.indd 2 1/11/2022 2:10:40 PM1/11/2022 2:10:40 PM

ENGLISH 3

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Before Use

IMPORTANT

• To ensure proper use, please read through this manual before using

this product. It is especially important that you read and observe

Warnings and Cautions in this manual.

• Please keep the manual in a safe and accessible place for future

reference.

WARNING

• Do not operate any function that takes your attention away

from safe driving.

CAUTION

Volume setting:

• Adjust the volume so that you can hear sounds outside the car to

prevent accidents.

• Lower the volume before playing digital sources to avoid damaging

the speakers by the sudden increase of the output level.

General:

• Avoid using the external device if it might hinder safe driving.

• Make sure all important data has been backed up. We shall bear no

responsibility for any loss of recorded data.

• Never put or leave any metallic objects (such as coins or metal tools)

inside the unit to prevent a short circuit.

• Depending on the types of cars, the antenna will automatically

extend when you turn on the unit with the antenna control wire

connected (page31). Turn off the unit or change the source to

STANDBY when parking at a low ceiling area.

Basics

Faceplate

Display window*

Volume knob

* Only for illustration purpose.

How to reset

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 3DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 3 7/14/2021 4:58:29 PM7/14/2021 4:58:29 PM

4ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

To On the faceplate

Turn on the power Press B SRC.

• Press and hold to turn off the power.

Adjust the volume Turn the volume knob.

Select a source • Press B SRC repeatedly.

• Press B SRC, then turn the volume

knob within 2 seconds.

Change the display information Press DISP repeatedly. (Page 33)

Getting Started

1 Select the display language and cancel the demonstration

When you turn on the power for the first time (or

[FACTORY RESET]

is set to

[YES]

, see page6), the display shows: “SEL LANGUAGE” “PRESS”

“VOLUME KNOB”

1 Turn the volume knob to select

[ENG]

(English) /

[SPA]

(Spanish) /

[FRE]

(French), then press the knob.

[ENG]

is selected for the initial setup.

Then, the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”.

3 Press the volume knob again.

[YES]

is selected for the initial setup.

4 Press the volume knob again.

“DEMO OFF” appears.

2 Set the clock and date

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select

[CLOCK]

, then press the knob.

Basics

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 4DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 4 7/14/2021 4:58:29 PM7/14/2021 4:58:29 PM

ENGLISH 5

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

To adjust the clock

3 Turn the volume knob to select

[CLOCKADJUST]

, then press the knob.

4 Turn the volume knob to make the settings, then press the knob.

Set the time in the order of “Hour” “Minute”.

5 Turn the volume knob to select

[CLOCK FORMAT]

, then press the knob.

6 Turn the volume knob to select

[12H]

or

[24H]

, then press the knob.

To set the date

7 Turn the volume knob to select

[DATEFORMAT]

, then press the knob.

8 Turn the volume knob to select

[DD/MM/YY]

or

[MM/DD/YY]

, then press

the knob.

9 Turn the volume knob to select

[DATESET]

, then press the knob.

10 Turn the volume knob to make the settings, then press the knob.

Set the date in the order of “Day” “Month” “Year” or “Month” “Day”

“Year”.

11 Press and hold to exit.

To return to the previous setting item, press .

3 Set the other optional settings

You can only set the following items while the unit is in STANDBY source.

1 Press B SRC repeatedly to enter STANDBY.

2 Press the volume knob to enter

[FUNCTION]

.

3 Turn the volume knob to select an item (see the following table), then

press the knob.

4 Repeat step 3 until the desired item is selected or activated.

5 Press and hold to exit.

To return to the previous setting item, press .

Getting Started

Default: [XX]

[DISPLAY]

[EASY MENU] When entering [FUNCTION]...

[ON]: [LCD DISPLAY] illumination changes to white color. ;

[OFF]: [LCD DISPLAY] illumination remains as [COLOR SELECT] color.

(Page 28)

• [KEY 1] and [KEY 2] illuminations change to light blue color when you

enter [FUNCTION], irregardless of the [EASY MENU] setting.

• Refer to the illustration on page 27 for zone identification.

[TUNER SETTING]

[PRESET TYPE] [NORMAL]: Memorizes one station for each preset button in each band

(FM1/FM2/FM3/AM). ; [MIX]: Memorizes one station or SiriusXM channel

for each preset button, regardless of the selected band or SiriusXM

channel.

[SYSTEM]

[KEY BEEP] [ON]: Activates the keypress tone. ; [OFF]: Deactivates.

[SOURCE SELECT]

[BT AUDIO SRC] [ON]: Enables BT AUDIO in source selection. ; [OFF]: Disables. (Page 20)

[BUILT-IN AUX] [ON]: Enables AUX in source selection. ; [OFF]: Disables. (Page 14)

[F/W UPDATE]

[UPDATE SYSTEM]

[F/W UP xxxx] [YES]: Starts upgrading the firmware. ; [NO]: Cancels (upgrading is not

activated).

For details on how to update the firmware, visit

<https://www.kenwood.com/cs/ce/>.

• Once you have upgraded the firmware, you are unable to downgrade

the firmware.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 5DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 5 7/14/2021 4:58:29 PM7/14/2021 4:58:29 PM

6ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

[FACTORY RESET] [YES]: Resets the settings to default (except the stored station). ;

[NO]: Cancels.

[ENGLISH] Select the display language for [FUNCTION] menu and music information

if applicable.

By default, [ENGLISH] is selected.

[ESPANOL]

[FRANCAIS]

Getting Started Radio

• “ST” indicator lights up when receiving an FM stereo broadcast with

sufficient signal strength.

• The unit switches to FM alarm automatically when receiving an alarm

signal from FM broadcast.

Search for a station

1 Press B SRC repeatedly to select RADIO.

2 Press BAND repeatedly to select FM1/FM2/FM3/AM.

3 Press S / T to search for a station.

You can store up to 18 stations for FM and 6 stations for AM.

• To store a station: Press and hold one of the number buttons (1 to 6).

• To select a stored station:

Press one of the number buttons (1 to 6).

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 6DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 6 7/14/2021 4:58:29 PM7/14/2021 4:58:29 PM

ENGLISH 7

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

Other settings

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default: [XX]

[TUNER SETTING]

[SEEK MODE] Selects the searching method for

S

/

T

buttons when pressed.

[AUTO1]: Automatically search for a station. ; [AUTO2]: Search for a preset

station. ; [MANUAL]: Manually search for a station.

[AUTO MEMORY] [YES]: Automatically starts memorizing 6 stations with good reception. ;

[NO]: Cancels.

• Selectable only if [NORMAL] is selected for [PRESET TYPE]. (Page 5)

[MONO SET] [ON]: Improves the FM reception, but the stereo effect will be lost. ;

[OFF]: Cancels.

[TI] [ON]: Allows the unit to temporarily switch to Traffic Information if

available (“TI” indicator lights up) while listening to all sources except in

AM. ; [OFF]: Cancels.

[PTY SEARCH] Select the available Program Type (see the following “Available Program

Type for [PTY SEARCH]”), then press

S

/

T

to start.

[CLOCK]

[TIME SYNC] [ON]: Synchronizes the unit’s time to the Radio Broadcast Data System

station time. ; [OFF]: Cancels.

Radio

•

[MONO SET]

/

[TI]

/

[PTY SEARCH]

is selectable only when the band is FM1/FM2/

FM3.

• If the volume is adjusted during reception of traffic information, alarm or

news bulletin, the adjusted volume is memorized automatically. It will be

applied the next time traffic information, alarm or news bulletin is turned

on.

Available Program Type for [PTY SEARCH]

[SPEECH]:

[NEWS], [INFORM] (information), [SPORTS], [TALK], [LANGUAGE], [REL TALK] (religious talk),

[PERSNLTY] (personality), [PUBLIC], [COLLEGE], [HABL ESP] (spanish talk), [WEATHER]

[MUSIC]:

[ROCK], [CLS ROCK] (classic rock), [ADLT HIT] (adult hits), [SOFT RCK] (softrock), [TOP 40],

[COUNTRY], [OLDIES], [SOFT], [NOSTALGA] (nostalgia), [JAZZ], [CLASSICL] (classical),

[R & B] (rhythm and blues), [SOFT R&B] (soft rhythm and blues), [REL MUSC] (religious music),

[MUSC ESP] (spanish music), [HIP HOP]

The unit will search for the Program Type categorized under

[SPEECH]

or

[MUSIC]

if selected.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 7DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 7 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

8ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

USB/iPod

Basic operations

Selectable source: USB/iPod USB or iPod BT

For playable audio file, see “Playable files” on page 32.

To On the faceplate

Play back/pause Press 6 IW.

Reverse/Fast-forward Press and hold S / T.

Select a file Press S / T.

Select a folder* Press 1 / 2 .

Repeat play Press 4 repeatedly.

[FILE REPEAT]

/

[FOLDER REPEAT]

/

[ALL REPEAT]

: MP3/

WMA/AAC/WAV/FLAC file

[REPEAT ONE]

/

[REPEAT ALL]

/

[REPEAT OFF]

: iPod

Connect a USB device

USB device

USB input terminal

USB type A cable*

(general products)

The source changes to USB automatically and playback starts.

* Do not leave the cable inside the car when not in use.

Connect an iPod/iPhone

USB input terminal

KCA-iP103*1 (optional accessory)

or accessory of the iPod/iPhone*2

iPod/

iPhone

See “Set the playable source for iPod/iPhone” on page 9 to start playback.

• You can also connect iPod/iPhone via Bluetooth. (Page16)

*1 KCA-iP103: Lightning type

*2 Do not leave the cable inside the car when not in use.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 8DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 8 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

ENGLISH 9

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

USB/iPod

To On the faceplate

Random play Press 3 repeatedly.

[FOLDERRANDOM]

/

[RANDOM OFF]

: MP3/WMA/AAC/

WAV/FLAC file

[SHUFFLE ON]

/

[SHUFFLE OFF]

: iPod

Press and hold 3 to select

[ALL RANDOM]

.*

* This does not work for iPod.

Select music drive

While in USB source, press 5 repeatedly.

Stored songs in the following drive will be played back.

• Selected internal or external memory of a smartphone (Mass Storage

Class).

• Selected drive of a multiple drive device. (This unit can support multiple

drive device of up to 4 drives. However, this unit may take some time to

read if three or more cards are connected.)

You can also select the music drive from the

[FUNCTION]

menu.

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select

[USB]

, then press the knob.

3 Turn the volume knob to select

[MUSIC DRIVE]

, then press the knob.

4 Turn the volume knob to select

[DRIVE CHANGE]

, then press the knob.

The next drive (

[DRIVE 1]

to

[DRIVE 4]

) is selected automatically and

playback starts.

5 Repeat step 1 to step 4 to select the following drives.

6 Press and hold to exit.

To return to the previous setting item, press .

Set the playable source for iPod/iPhone

You can make the following setting at all sources except at iPod USB source

and iPod BT source.

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated.

4 Press and hold to exit.

To return to the previous setting item, press .

Default: [XX]

[USB]

[IPHONE SETUP] [BT]: iPod BT source is available if iPod/iPhone is connected via

Bluetooth.

• If you connect the iPod/iPhone via USB input terminal, iPod USB source

is not available.

However, once the Bluetooth is disconnected, iPod USB source will

become available. ;

[USB]: iPod USB source is available if iPod/iPhone is connected via USB

input terminal, regardless of whether Bluetooth connection is available

or not.

• Alexa mobile application cannot be used when iPod USB source is

selected.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 9DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 9 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

10 ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

USB/iPod

[SKIP SEARCH] setting

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select

[USB]

, then press the knob.

3 Turn the volume knob to select

[SKIP SEARCH]

, then press the knob.

4 Turn the volume knob to select the skip search ratio, then press the

knob.

[0.5%]

(default)/

[1%]

/

[5%]

/

[10%]

The skip search ratio is shown as a percentage of the total files.

5 Press and hold to exit.

Alphabet search

(applicable only for iPodUSB source and iPodBT source)

You can search for a file according to the first character.

1 Press .

2 Turn the volume knob to select a list, then press the knob.

3 Turn the volume knob quickly to enter character search.

4 Turn the volume knob to select the character.

• Select “

* ” to search for a character other than A to Z, 0 to 9.

5 Press S / T to move to the entry position.

• You can enter up to 3 characters.

6 Press the volume knob to start searching.

7 Turn the volume knob to select a file, then press the knob.

Selected file starts playing.

• To return to the root folder/first file/top menu, press 5. (Not applicable for

BT AUDIO source.)

• To return to the previous setting item, press .

• To cancel, press and hold .

Select a file to play

From a folder or list

1 Press .

2 Turn the volume knob to select a folder/list, then press the knob.

3 Turn the volume knob to select a file, then press the knob.

Selected file starts playing.

Quick search

(applicable only for USB source)

If you have many files, you can search through them quickly.

1 Press .

2 Turn the volume knob to select a folder/list, then press the knob.

3 Turn the volume knob quickly to browse through the list quickly.

4 Turn the volume knob to select a file, then press the knob.

Selected file starts playing.

Skip search

(applicable only for iPodUSB source and iPodBT source)

If you have many files in the selected list, you can perform the following to

search for a file by skipping through the list at a rate selected in

[SKIP SEARCH]

.

1 Press .

2 Turn the volume knob to select a list, then press the knob.

3 Press S / T to search at a preset skip search ratio.

• Pressing and holding S / T searches at a 10% ratio irregardless of

the

[SKIP SEARCH]

settings.

4 Turn the volume knob to select a file, then press the knob.

Selected file starts playing.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 10DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 10 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

ENGLISH 11

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

SiriusXM® Radio

Start listening

1 Press B SRC repeatedly to select SIRIUSXM.

2 Press BAND repeatedly to select a band.

3 Press .

“ ” indicator lights up.

4 Turn the volume knob to select a category, then press the knob.

If “ALL CHANNELS” is selected, all the available channels will be shown.

5 Turn the volume knob to select a channel, then press the knob.

• Pressing and holding 1/2 changes the channel rapidly.

• If no operation is done for 10 seconds, a channel will be selected

automatically.

(or)

Press S / T to search for a channel manually.

• Pressing and holding S / T changes the channel rapidly.

If a locked channel or a mature channel is selected, a pass code input

screen appears. Enter the pass code to receive the channel. (Page13)

Parental Control

The Parental Control feature allows you to limit access to any SiriusXM

channels, including those with mature content.

When enabled, the Parental Control feature requires you to enter a pass

code to tune to the locked channels.

• Information on setting up the pass code and locking channels can be

found on page 13.

Only SiriusXM® brings you more of what you love to listen to, all in one place.

Get over 140 channels, including commercial-free music plus the best sports,

news, talk, comedy and entertainment. Welcome to the world of satellite

radio.

A SiriusXM Vehicle Tuner and Subscription are required.

• For more information, visit <www.siriusxm.com>.

Preparation:

1 Connect the optional SiriusXM Vehicle Tuner (commercially available).

Antenna

Expansion port on

the rear panel

SiriusXM Vehicle Tuner

2 Check your Radio ID for activation.

The SiriusXM Radio ID is required for activation and can be found by

tuning to Channel 0 as well as on the label found on the SiriusXM Vehicle

Tuner and its packaging.

The Radio ID does not include the letters I, O, S or F.

3 Activate the subscription.

For users in the U.S.A.:

Online: Go to <www.siriusxm.com/activatenow>

Phone: Call 1-866-635-2349

For users in Canada:

Online: Go to <www.siriusxm.ca/activate>

Phone: Call 1-888-539-7474

4 Press B SRC repeatedly to select SIRIUSXM to start updating.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 11DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 11 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

12 ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

SiriusXM Keymode

Press and hold the volume knob to change the keymode (channel or

replay). (Default: Channel keymode)

“” indicator lights up when replay keymode is selected.

When channel keymode is selected...

To On the faceplate

Select a channel Press S / T.

Change a channel rapidly Press and hold S / T.

Store a channel of the current band Press and hold one of the number

buttons (1 to 6).

Select a stored channel of the

current band

Press one of the number buttons

(1 to 6).

When replay keymode is selected...

To On the faceplate

Play back/pause Press 6 IW.

Skip backward/forward Press S / T*.

Rewind/Fast-forward Press and hold S / T*.

Go to Live Press 1*.

* When Live is reached or selected, keymode is automatically changed to channel keymode.

SmartFavorites and TuneStart™

User stored channels are recognized as SmartFavorite channels*. The

SiriusXM Vehicle Tuner automatically buffers the broadcast content in the

background.

• SmartFavorites feature is available with SXV200 or later SiriusXM Vehicle

Tuner.

* SXV300 (and later) SiriusXM Vehicle Tuner can use all 18 stored channels as SmartFavorites.

The SXV200 SiriusXM Vehicle Tuner can use 6 stored channels from the current band as

SmartFavorites.

When you select a SmartFavorite channel, you can rewind and replay up to

30 minutes of any of the missed news, talk, sports or music content.

• Playback starts from the beginning of the song if

[TUNE START]

is set to

[ON]

(page 13) for most music channels stored as a SmartFavorite.

Press one of the number buttons (1 to 6) to select a stored channel.

TuneScan™

You can get a short preview of the songs that you have missed on each of

your SmartFavorites music channels or a music channel currently tuned into.

Press and hold BAND to start scanning the first 6 seconds of the recorded

music contents.

• To listen to the current song, press the volume knob to stop scanning. The

unit continues playing the current song.

• To select the previous/next song, press S / T.

• To cancel scanning, press and hold the volume knob. Playback returns to

the channel before you entered TuneScan.

• Pressing any button other than volume knob or S / T will interrupt

scanning and eventually stop scanning.

SiriusXM® Radio

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 12DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 12 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

ENGLISH 13

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

SiriusXM® Radio

SiriusXM settings

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select an item (see the following table), then

press the knob.

3 Repeat step 2 until the desired item is selected/activated or follow the

instructions stated on the selected item.

4 Press and hold to exit.

To return to the previous setting item, press .

Default: [XX]

[SIRIUS XM]

[SEEK MODE] Selects the tuning method for

S

/

T

buttons when pressed.

[CHANNEL]: Manually search for a channel. ; [PRESET]: Search for a

preset channel of the selected band. (Automatically search for preset 1

channel if the current channel is not a preset channel.)

[CHANNEL LOCK] To unlock settings:

1

Turn the volume knob to select a number.

2

Press

S

/

T

to move to the entry position.

3

Repeat step 1 and step 2 to enter the current pass code.

(Initial pass code is 0000.)

4

Press the volume knob to confirm.

[CODESET]

1

Turn the volume knob to select a number.

2

Press

S

/

T

to move to the entry position.

3

Repeat step 1 and step 2 to enter a new 4-digit pass code.

4

Press the volume knob to confirm.

5

Repeat step 1 to step 4 to reconfirm the pass code.

• Make a note of the new pass code to enter channel lock settings for

next time.

[LOCK SETTING] [MATURE CH]: Selects the SiriusXM-defined lock setting. ;

[USER DEFINED]: Selects the individual channels the user wants to lock. ;

[OFF]: Cancels.

[CHANNEL EDIT]*1

1

Turn the volume knob to select a category, then press the knob.

2

Turn the volume knob to select a channel you want to lock, then press

the knob.

“L” appears in front of the channel number.

3

Press and hold to exit.

[CHANNEL

CLEAR]*1

[YES]: Clears all the locked channels. ; [NO]: Cancels.

[TUNE START]*2 [ON]: All qualified music channels in the SmartFavorites will start

playback from the beginning of the song. ; [OFF]: Cancels.

[SIGNAL LEVEL] Shows the strength ([NO SIGNAL]/[WEAK]/[GOOD]/[STRONG]) of the

current received signal.

[BUFFER USAGE] Shows the memory usage ([0%] to [100%]) for Replay buffer.

[SXM RESET] [YES]: Resets all SiriusXM settings to default. ; [NO]: Cancels.

*1 Displayed only when [LOCK SETTING] is set to [USER DEFINED].

*2 Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later which supports

SmartFavorites.

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 13DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 13 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

14 ENGLISH

Data Size: B6L (182 mm x 128 mm)

Book Size: B6L (182 mm x 128 mm)

You can listen to music from a portable audio player via the auxiliary input

jack.

Preparation:

Select

[ON]

for

[BUILT-IN AUX]

in

[SOURCESELECT]

. (Page5)

Start listening

1 Connect a portable audio player (commercially available).

Portable audio

player

3.5 mm (1/8”) stereo mini plug with “L”

shaped connector (commercially available)

Auxiliary input jack

2 Press B SRC repeatedly to select AUX.

3 Turn on the portable audio player and start playback.

Set the name of the external device

While listening to a portable audio player connected to the unit...

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select

[SYSTEM]

, then press the knob.

3 Turn the volume knob to select

[AUX NAME SET]

, then press the knob.

4 Turn the volume knob to select an item, then press the knob.

[AUX]

(default)/

[DVD]

/

[PORTABLE]

/

[GAME]

/

[VIDEO]

/

[TV]

5 Press and hold to exit.

To return to the previous setting item, press .

AUX KENWOOD Remote Application

You can control the KENWOOD car receiver from iPhone/iPod touch (via

Bluetooth or via USB input terminal) or Android device (via Bluetooth) using

KENWOOD Remote application.

• For more information, visit <https://www.kenwood.com/cs/ce/>.

Preparation:

Install the latest version of KENWOOD Remote application on your device

before connecting.

Start using KENWOOD Remote application

1 Start up the KENWOOD Remote application on your device.

2 Connect your device.

• For Android device:

Pair the Android device with this unit via Bluetooth. (Page 16)

• For iPhone/iPod touch:

Connect iPhone/iPod touch to the USB input terminal. (Page 8)

(or)

Pair the iPhone/iPod touch with this unit via Bluetooth. (Page 16)

(Make sure the USB input terminal is not connected to any device.)

3 Select the device to use from the

[FUNCTION]

menu.

See the following “ Settings to use KENWOOD Remote application”.

By default,

[ANDROID]

is selected. To use iPhone/iPod touch, select

[YES]

for

[IOS]

.

Settings to use KENWOOD Remote application

1 Press the volume knob to enter

[FUNCTION]

.

2 Turn the volume knob to select an item (page 15), then press the

knob.

3 Repeat step 2 until the desired item is selected or activated.

4 Press and hold to exit.

To return to the previous setting item, press .

DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 14DPX395MBT_K_B5A-3890-00_EN_1st Draft.indd 14 7/14/2021 4:58:30 PM7/14/2021 4:58:30 PM

La page charge ...

Kenwood DPX305MBT Guide d'installation

Kenwood DPX305MBT Guide d'installation

dans d''autres langues

Documents connexes

Autres documents