Quick Installation Guide
Pro Series
Battery-powered Remote
Water Sensing Pod Add-on
for the Whole Home Smart Wi-Fi Water Leak Sensor Kit
DCH-S163 A1
Setup Code
This is your device’s Setup Code.
Please keep it as future reference
for your device.
Simple Setup
Get the mydlink app on the App Store
or on Google Play. Launch the app, then
Sign In or Create a New Account.
1
mydlink
2Tap then tap Add a Device.
Note: Make sure that your DCH-S162 hub is
set up and functioning properly beforehand.
3Tap Scan, then scan the Setup Code
located in the Setup Code section.
Follow the app instructions to set up
your device with your DCH-S162 hub.
Note: This is an add-on to the Pro Series Whole
Home Smart Wi-Fi Water Leak Sensor Starter Kit. The
DCH-S162 is required for this device to function.
(pre-installed)
What do I do if my device is not
working properly?
Reset and reinstall your device. During
installation, ensure that:
•Your router is connected to the
Internet and Wi-Fi is enabled
•Your mobile device is connected to
your router’s Wi-Fi and Bluetooth is
enabled
•Your mydlink device is in range of
your Wi-Fi network
•Ensure that your DCH-S162 hub is
powered on and installed correctly
How do I reset my device?
DCH-S163: Press and hold the Reset
button until it blinks red.
Reset button
How do I install additional DCH-S163
units?
In the mydlink app,
tap then tap
Add a Device.
Tap Scan, then scan
the Setup Code located on the device.
Follow the app instructions to set up
the additional DCH-S163 units with
your DCH-S162 hub.
Status LED
Paired to the hub
Connection failed
Power saving mode
Water leak detected
LED Behavior FAQ
Need Help?
Having trouble installing your new
product? D-Link’s support website
contains live chat, video tutorials,
commonly asked questions, the
latest user documentation and
software updates for D-Link products.
Contact Us
http://support.dlink.ca
(800) 361-5265
Waiting to pair
2020/12/02 Ver 1.00(CA)_65x55
Setup and How To videos available here:
YouTube.com/DLinkTutorials
Attention
FCC:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help. This device must
not be co-located or operating in conjunction with any other antenna or transmitter.
Operation is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS
NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
IC：
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux
appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
The device meets the exemption from the routine evaluation limits in section 2.5 of
RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian
information on RF exposure and compliance.
(3) Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la
section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut
obtenir l'information canadienne sur l'exposition et la conformité de rf.
-
1
-
2
-
3
