Whirlpool 400011543529 Manuel utilisateur

User and maintenance manual

Bedienungs- und Wartungsanleitung

Manuel d'utilisation et d'entretien

Handleiding voor gebruik en onderhoud

Manual de utilização e manutenção

EN

DE

NL

PT

EN1

These instructions shall also be available on website: docs.whirlpool.eu

YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

All safety warnings give specific details of the potential risk present and

indicate how to reduce risk of injury, damage and electric shock

resulting from improper use of the appliance. Carefully observe the

following instructions:

- Keep these instructions close at hand for future reference.

- Use protective gloves to perform all unpacking and installation

operations.

- The appliance must be handled and installed by two or more

persons.

- The appliance must be disconnected from the power supply before

carrying out any installation work.

- Installation and maintenance must be carried out by a qualified

technician, in compliance with the manufacturer’s instructions and

local safety regulations. Do not repair or replace any part of the

appliance unless specifically stated in the user manual.

- Power cable replacement must be carried out by a qualified

electrician. Contact an authorized service centre.

- Regulations require that the appliance is earthed.

- The power cable must be long enough for connecting the

appliance, once fitted in its housing, to the main power supply.

- For installation to comply with current safety regulations, an

omnipolar switch with minimum contact gap of 3 mm must be

utilized.

- Do not use extension leads, multiple socket adapters.

- Do not connect the appliance to a socket which can be operated by

remote control or timer.

- Do not pull the power supply cable.

- The electrical components must not be accessible to the user after

installation.

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING Indicates a hazardous situation which, if not avoided, could cause serious injury.

EN2

- If the surface of the induction plate is cracked, do not use it and

switch off the appliance to avoid the possibility of electric shock

(only for models with induction function).

- Do not touch the appliance with any wet part of the body and do

not operate it when barefoot.

-

This appliance is designed solely for use as a domestic appliance for

cooking food. No other type of use is permitted (e.g.: heating rooms).

The Manufacturer declines any liability for injury to persons or

animals or damage to property if these advices and precautions are

not respected.

- The appliance and its accessible parts become hot during use.

Care should be taken to avoid touching heating elements.

Very young (0-3 years) and young children (3-8 years) shall be kept

away unless continuously supervised.

- Children from 8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of experience and

knowledge can use this appliance only if they are supervised or

have been given instructions on safe appliance use and if they

understand the hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall not be made by

children without supervision.

- During and after use, do not touch the heating elements or interior

surfaces of the appliance - risk of burns.

Do not allow the appliance to come into contact with cloths or

other flammable materials until all the components have cooled

down completely.

- At the end of cooking, exercise caution when opening the

appliance door, letting the hot air or steam exit gradually before

accessing the oven. When the appliance door is shut, hot air is

vented from the aperture above the control panel. Do not obstruct

the vent apertures.

- Use oven gloves to remove pans and accessories, taking care not to

touch the heating elements.

- Do not place flammable materials in or near the appliance: a fire

may break out if the appliance is inadvertently switched on.

- Do not heat or cook sealed jars or containers in the appliance.

The pressure that builds up inside might cause the jar to explode,

damaging the appliance.

- Do not use containers made of synthetic materials.

EN3

- Overheated oils and fats catch fire easily. Always remain vigilant

when cooking foods rich in fat and oil.

- Never leave the appliance unattended during food drying.

- If alcoholic beverages are used when cooking foods (e.g. rum,

cognac, wine), remember that alcohol evaporates at high

temperatures. As a result, there is a risk that vapours released by the

alcohol may catch fire upon coming into contact with the electrical

heating element.

- Overheated oils and fats catch fire easily. Always remain vigilant

when cooking foods rich in fat, oil or alcohol (e.g. rum, cognac, wine).

- Never use steam cleaning equipment.

- Do not touch the oven during the pyrolysis cycle. Keep children

away from the oven during the pyrolysis cycle. For optimum

cleaning results, remove excessive residuals inside the cavity and

clean the inner door glass before using the Pyro function.

- During and after the pyrolysis cycle, the animals have to be kept

away from the area of the appliance location (only for ovens with

Pyrolysis function).

- Only use the temperature probe recommended for this oven.

- Do not use harsh abrasive cleaners or sharp metal scrapers to clean

the oven door glass since they can scratch the surface, which may

result in shattering of the glass.

- Ensure that the appliance is switched off before replacing the lamp

to avoid the possibility of electric shock.

- Do not use aluminium foil to cover food in the cooking vessel (only

for ovens with cooking vessel supplied).

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with

local waste disposal regulations. Before scrapping, cut off the power supply cable.

- For further information on the treatment, recovery and recycling of household electrical appliances,

contact your competent local authority, the collection service for household waste or the store where

you purchased the appliance.

After unpacking the oven, make sure that it has not been damaged during transport and that the oven

door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. To

prevent any damage, only remove the oven from its polystyrene foam base at the time of installation.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all

wood chips and sawdust.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the

upper edge of the oven.

INSTALLATION

EN4

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The

dataplate is on the front edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm2) must be carried out by a qualified electrician.

Contact an authorized service centre.

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective film and adhesive labels from accessories.

- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell

and fumes from the insulating materials and protective grease.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Never pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become

trapped in the door.

- Do not expose the oven to atmospheric agents.

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of

the packing must therefore be disposed of responsibly and in full compliance with local authority

regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and

Electronic Equipment (WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

- The symbol on the product or on the accompanying documentation indicates that it should not be

treated as domestic waste but must be taken to an appropriate collection centre for the recycling of

electrical and electronic equipment.

Energy saving tips

- Only pre-heat the oven if specified in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

- Switch the oven off 10/15 minutes before the set cooking time. Food requiring prolonged cooking will

continue to cook even once the oven is switched off.

- This appliance has been designed, constructed and distributed in compliance with the requirements

of European Directives: LVD 2014/35/ EU, EMC 2014/30/EU and RoHS 2011/65/ EU.

- This appliance, which is intended to come into contact with foodstuffs, complies with European

Regulation n.1935/2004.

- This appliance meets the Eco Design requirements of European Regulations n. 65/2014, and n. 66/

2014 in conformity to the European standard EN 60350-1.

SAFEGUARDING THE ENVIRONMENT

DECLARATION OF CONFORMITY

EN5

The oven does not work:

• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.

• Turn off the oven and restart it to see if the fault persists.

The door will not open:

• Turn off the oven and restart it to see if the fault persists.

•Important: during self-cleaning, the oven door will not open. Wait until it unlocks automatically (see

paragraph “Cleaning cycle of ovens with pyrolysis function”).

The electronic programmer does not work:

• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service.

Specify in this case the number that follows the letter “ ”.

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the

“Troubleshooting guide“.

2. Switch the appliance off and back on again it to see if the fault persists.

If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right hand

edge of the oven cavity (visible when the oven door is open). The service number is also indicated on

the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-sales Service (to guarantee that original

spare parts will be used and repairs carried out correctly).

Oven exterior

IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally

comes into contact with the appliance, clean immediately with a damp microfibre cloth.

• Clean the surfaces with a damp microfibre cloth. If it is very dirty, add a few drops of washing up

detergent to the water. Finish off with a dry cloth.

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

CLEANING

WARNING - Never use steam cleaning equipment.

- Only clean the oven when it is cool to the touch.

- Disconnect the appliance from the power supply.

EN6

Oven interior

IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin

enamelled surfaces and the oven door glass.

• After every use, allow the oven to cool then clean it preferably while it is still warm in order to remove

built-up dirt and stains caused by food residues (e.g. food with a high sugar content).

• Use proprietary oven detergents and follow the manufacturer’s instructions to the letter.

• Clean the door glass with a suitable liquid detergent. The oven door can be removed to facilitate

cleaning (see MAINTENANCE).

• The top heating element of the grill (see MAINTENANCE) can be lowered (some models only) to clean

the roof of the oven.

N.B.: during prolonged cooking of foods with a high water content (e.g. pizza, vegetables, etc.)

condensation may form on the inside of the door and around the seal. When the oven is cold, dry the

inside of the door with a cloth or sponge.

Accessories:

• Soak the accessories in water with washing up detergent immediately after use, handling them with

oven gloves if still hot.

• Food residues can be easily removed using a brush or sponge.

Cleaning the rear wall and catalytic side panels of the oven (if present):

IMPORTANT: do not use corrosive or abrasive detergents, coarse brushes, pot scourers or oven

sprays which could damage the catalytic surface and ruin its self-cleaning properties.

• Operate the oven empty with the fan-assisted function at 200°C for about one hour

• Next, leave the appliance to cool down before removing any food residue with a sponge.

Cleaning cycle of ovens with pyrolysis function:

This function burns off spatters produced inside the oven during cooking at a high temperature. At this

high temperature, the deposits turn into a light ash which can be easily wiped away with a damp cloth,

when the oven is cool. Do not select the pyrolysis function after every use, only when the oven is very dirty

or produces smoke or fumes while preheating or cooking.

• If the oven is installed below a hob, make sure that all burners or electric hotplates are switched off

during the self-cleaning (pyrolysis) function.

• Remove all accessories before running the pyrolysis function (also the lateral grids).

• For optimum cleaning results, remove excessive residuals inside the cavity and clean the inner door

glass before using the Pyro function.

The appliance is equipped with 2 pyrolysis functions:

1. Energy-saving cycle (PYRO EXPRESS/ECO): which consumes approximately 25% less energy than the

standard cycle. Select it at regular intervals (after cooking meat on 2 or 3 consecutive occasions).

2. Standard cycle (PYRO): which is suitable for cleaning a very dirty oven.

• In any case, after a certain number of uses and depending on how dirty the oven is, a message on the

oven display advises you to run a self-cleaning cycle.

N.B.: during the pyrolysis function, the oven door will not open; it will remain locked until the

temperature inside the oven has returned to an acceptably safe level.

WARNING - Do not touch the oven during the pyrolysis cycle.

- Keep children away from the oven during the pyrolysis cycle.

EN7

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (Fig. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).

To refit the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

TO REMOVE THE SIDE GRILLES

In some models, the side accessory holder grilles are equipped with fixing screws (Fig. 3) for optimum

stability.

1. Remove the screws and relative plates on the right and left with the aid of a coin or tool (Fig. 4).

2. To remove the grilles, lift the up (1) and turn them (2) as shown in Fig. 5.

MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles.

2. Pull the heating element out a little (Fig. 6) and lower it (Fig. 7).

3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to

rest on the lateral supports.

MAINTENANCE

WARNING - Use protective gloves.

- Ensure the oven is cold before carrying out the following operations.

- Disconnect the appliance from the power supply.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

Fig. 6 Fig. 7

2

1

EN8

REPLACING THE OVEN LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the power supply.

2. Unscrew the lamp cover (Fig. 8), replace the lamp (see note for lamp type) and screw the lamp cover

back on.

3. Reconnect the oven to the power supply.

To replace the side lamp (if present):

1. Disconnect the oven from the power supply.

2. Remove the side accessory holder grilles, if present.

3. Use a screwdriver to prise off the lamp cover.

4. Replace the lamp (see note for lamp type).

5. Refit the lamp cover, pushing it on firmly until it clicks into place.

6. Refit the side accessory holder grilles.

7. Reconnect the oven to the power supply.

N.B:

- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C

halogen lamps.

- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for

household room illumination (Commission Regulation (EC) No 244/2009).

- Lamps are available from our After-sales Service.

IMPORTANT:

- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.

- Do not use the oven until the lamp cover has been repositioned.

Fig. 8 Fig. 9 Fig. 10 Fig. 11

EN9

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Dataplate (not to be removed)

5. Lamp

6. Circular heating element (not visible)

7. Fan

8. Turnspit

9. Lower heating element (not visible)

10. Door

11. Position of shelves (the number of shelves is indicated on the front of the oven)

12. Rear wall

N.B.:

- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a

while.

- When the oven door is opened during cooking, the heating elements switch off.

ACCESSORIES SUPPLIED

A. WIRE SHELF: the wire shelf can be used to grill food or as a support for pans, cake tins and other

ovenproof cooking receptacles.

B. DRIP TRAY: the drip tray is designed to be positioned under the wire shelf in order to collect fat or as

an oven tray for cooking meat, fish, vegetables, focaccia, etc.

C. TURNSPIT: for even roasting of large pieces of meat and poultry.

The number of accessories may vary according to which model is purchased.

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-sales Service.

INSTRUCTIONS FOR OVEN USE

Fig. A Fig. B Fig. C

EN10

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).

2. Other accessories, such as the drip tray and baking tray, are inserted in the same way as the wire shelf

(Fig. 2).

CONTROL PANEL DESCRIPTION

ELECTRONIC PROGRAMMER

1. FUNCTION SELECTOR KNOB: On/off and function selector knob

2. BROWSE KNOB: for browsing the menu and adjusting pre-set values

3. SELECTION/CONFIRMATION BUTTON

N.B.:the display shows for indications regarding this button.

LIST OF FUNCTIONS

Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the

associated submenus.

The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,

SETTINGS, BREAD/PIZZA, AUTOMATIC OVEN CLEANING.

N.B.:for the list and description of functions, see the specific table at page15.

DESCRIPTION OF DISPLAY

A. Display of heating elements activated during the various cooking functions

B. Time management symbols: timer, cooking time, end of cooking time, time

C. Information regarding selected functions

D. Automatic BREAD/PIZZA function selected

E. Indication of door locked during automatic cleaning cycle (pyro-cleaning)

F. Internal oven temperature

G. Pyrolisis function

H. Browning

I. Special functions: Defrost, Keep Warm, Rising

Fig. 1 Fig. 2

A

DISPLAY

1 23

A

B C D

E

I H G F

EN11

STARTING THE OVEN - SETTING LANGUAGE

At the first switch on of the oven, display shows ENGLISH.

Turn the “Browse” knob until the desired language is displayed then press the button to confirm.

SETTING THE TIME

After setting the language, the time must be set on the clock. The two hour digits flash on the display.

1. Turn the “Browse” knob to display the correct hour.

2. Press the button to confirm; the two minute digits flash on the display.

3. Turn the “Browse” knob to display the correct minutes.

4. Press button to confirm.

To change the time, for example following a power cut, see the next paragraph (SETTINGS).

SELECTING COOKING FUNCTIONS

1. Turn the “Functions” knob to the desired function: the cooking settings are shown on the display.

2. If the values shown are those desired, press . To change them, proceed as indicated below.

SETTING THE TEMPERATURE/OUTPUT OF THE GRILL

To change the temperature or output of the grill, proceed as follows:

1. Turn the “Browse” knob to display the desired value.

2. Press button to confirm.

The oven automatically confirms your selection 10 seconds after the last operation.

FAST PREHEATING

1. Turn the “Functions” knob to the symbol to select the fast preheating function.

2. Confirm by pressing : the settings are shown on the display.

3. If the proposed temperature is that desired, press button . To change the temperature, proceed as

described in previous paragraphs. The message PRE appears on the display. When the set

temperature is reached, the corresponding value (e.g. 200°) and an acoustic signal will sound. At the

end of preheating, the oven automatically selects the conventional function .

At this point food can be placed in the oven for cooking.

4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired

function.

3

PRE

3

EN12

SETTING COOKING TIME

This function can be used to cook food for a set length of time, from a minimum of 1 minute to the

maximum time allowed by the selected function, after which the oven switches off automatically.

1. Once the temperature is confirmed, the symbol flashes.

2. Turn the adjustment knob to display the desired cooking time.

3. To confirm the cooking time, press button .

SETTING END OF COOKING TIME/START DELAYED

IMPORTANT:the start delayed setting is not available for the following functions: FAST

PREHEATING, BREAD/PIZZA, GENTLE CONVECTION BAKE.

N.B.:with this setting, the selected temperature is reached in a more gradual way, so cooking times

will be slightly longer than stated in the cooking table.

N.B.: Delay to start functionality is not available for Grill and Turbo Grill functions.

The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and 59

minutes. This can only be done once cooking time has been set.

After setting cooking time, the display shows the end of cooking time (for example 15:45) and the

symbol flashes.

To delay the end of cooking time, and thus also the cooking start time, proceed as follows:

1. Turn the “Browse” knob to display the time you wish cooking to end (for example 16:00).

2. Confirm the selected value by pressing button : the two dots of end of cooking time flash,

indicating that the setting has been made correctly.

3. The oven will automatically delay the start of cooking so as to finish cooking at the set time.

TIMER

This function can be used only with the oven switched off and is useful, for example, for monitoring the

cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes.

1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time.

2. Press button to start the countdown. When the set time has elapsed, the display will show “END”

and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day

appears on the display).

SELECTING SPECIAL FUNCTIONS

Turn the “Functions” knob indicator to the symbol to access a submenu containing special functions.

To browse, select and start one of these functions, proceed as follows:

1. Turn the “Functions” knob to symbol : the display shows “ DEFROST” along with this function’s

corresponding symbol.

2. Turn the “Browse” knob to scroll the list of functions; DEFROST, KEEP WARM, RISING.

3. Press button to confirm.

3

DEFRO WARM RISIN

3

EN13

BROWNING

At the end of cooking, with certain functions, the display indicates the possibility of browning. This

function can only be used when cooking time has been set.

At the end of cooking time, the display shows: “PRESS TO BROWN”. Press button , and the oven starts

a 5 minute browning cycle. This function can be selected consecutively a maximum of twice.

BREAD/PIZZA FUNCTION SELECTION

Turn the “Functions” knob indicator to the symbol to access a submenu containing two automatic

cooking functions for “bread” and “pizza”.

Bread

1. Turn the “Functions” knob to symbol : the display shows “BREAD” and AUTO at the side.

2. Press to select the function.

3. Turn the “Browse” knob to set the required temperature (between 180°C and 220°C) and confirm with

button .

4. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

Pizza

1. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function,

proceed as follows:

2. Turn the “Browse” knob: “PIZZA” appears on the display.

3. Press to select the function.

4. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with

button .

5. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

PRESS

3

BREAD

3

PIZZA

3

EN14

SETTINGS

Turn the “Functions” knob indicator to the symbol to access a submenu containing five display settings

which can be changed.

Language

1. Turn the “Browse” knob to display “LANGUAGE”.

2. Press to access the setting.

3. Turn the “Browse” knob to select the desired language and confirm by pressing button .

Clock

Turn the “Browse” knob to display CLOCK. To change the time, see the previous section (SETTING THE

CURRENT TIME).

Eco

With the ECO mode selected (ON), the display reduces the brightness, showing the clock when the oven is

on standby position from 3 minutes. Also, the oven light is switched off during cooking. To view

information on the display and switch the light on again, just press the button or turn one of the knobs.

1. Turn the “Browse” knob to display “ECO.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

4. During a cooking function, if the Eco Mode is activated, the cavity lamp will be switched off after

1 minute of cooking and reactivated for each user interaction.

Acoustic signal

To activate or deactivate the acoustic signal, proceed as follows:

1. Turn the “Browse” knob to display “SOUND.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

Brightness

To change the display brightness, proceed as follows:

1. Turn the “Browse” knob to display “BRIGHTNESS.

2. Press button : number 1 appears on the display.

3. Turn the “Browse” knob to increase or decrease brightness and confirm by pressing .

AUTOMATIC OVEN CLEANING

For the description of this function, see the chapter CLEANING and the functions table at page15.

To activate the oven’s automatic cleaning cycle (pyro-cleaning), proceed as follows:

1. Turn the “Functions” knob to symbol : the word PYRO appears on the display.

2. Press button to confirm your choice and start the pyro-cleaning cycle.

To select ECO pyro-cleaning, turn the “Browse” knob: the word ECO appears bottom right on the display.

Press button to start the shorter programme.

During pyro-cleaning, the oven door is automatically locked and the symbol appears on the display. The

door remains locked at the end of the cleaning cycle: “COOL” appears on the display, indicating the oven

is still cooling down. When the oven cools to a safe temperature, the symbol switches off and the display

shows “END”.

N.B.:the automatic door lock control procedure fails to execute properly, the symbol appears on the

display. If, on the other hand, the door remains closed due to a fault in the locking system, and “DOOR

LATCHED” appear on the display. In this case, contact the After-sales Service.

3

COOL

PYRO

3

EN15

OVEN FUNCTION DESCRIPTION TABLE

FUNCTIONS KNOB

OFF To stop cooking and switch off the oven.

LAMP To switch the oven interior light on/off.

SPECIALS

DEFROST

To speed up defrosting of food. Place food on the middle shelf. Leave food in

its packaging in order to prevent it from drying out on the outside.

KEEP WARM

For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).

Place food on the middle shelf. The function will not activate if the

temperature in the oven is above 65°C.

RISING

For optimal rising of sweet or savory dough. Place the dough on the 2nd

shelf. The oven does not have to be preheated. To safeguard the quality of

proving, do not activate the function if the oven is still hot after a cooking

cycle.

CONVENTIONAL To cook any kind of dish on one shelf only. Use the 2nd shelf. Preheat the

oven before placing food inside.

CONVECTION

BAKE

For baking cakes with liquid filling (sweet or savoury) on a single shelf. This

function can also be used for cooking on two shelves. Switch the position of

the dishes to cook food more evenly. Use the 2nd shelf to cook on one shelf

only, and the 1st and 3rd to cook on two shelves. Preheat the oven before

cooking.

GENTLE

CONVECTION

BAKE

To cook food requiring medium/low cooking temperatures on a maximum

of two shelves. This function is used to cook gently and slowly on two levels

without having to switch the position of the dishes during the cooking

process. Use the 2nd shelf to cook on one shelf only, and the 1st and 4th to

cook on two shelves. Preheat the oven before cooking.

GRILL

To grill steak, kebabs and sausages; to cook vegetables au gratin and toast

bread. Place food on the 4th shelf. When grilling meat, use the drip tray to

collect the cooking juices. Position it on the 3rd shelf, adding approx. half a

litre of water. The oven does not have to be preheated. During cooking the

oven door must remain closed.

TURBO GRILL

To roast large joints of meat (legs, roast beef, chickens). Position the food on

the middle shelves. Use the drip tray to collect the cooking juices. Position it

on the 1st/2nd shelf, adding approx. half a litre of water. The oven does not

have to be preheated. During cooking the oven door must remain closed.

With this function you can also use the turnspit, if provided.

MAXI COOKING

To cook large joints of meat (above 2.5 kg). Use the 1st or 3rd shelves,

depending on the size of the joint. The oven does not have to be preheated.

It is advisable to turn the meat over during cooking for more even

browning. It is best to baste the meat every now and again to prevent it

from drying out.

SETTINGS To set the display (language, time, brightness, buzzer volume, energy

saving).

EN16

BREAD/PIZZA

To bake different types and sizes of pizza and bread. This function contains

two programmes with predefined settings. Simply indicate the values

required (temperature and time) and the oven will manage the cooking

cycle automatically. Place the dough on the 2nd shelf after preheating the

oven.

AUTOMATIC OVEN

CLEANING

To burn off spatters produced during cooking with an extremely high

temperature cycle. Two auto-cleaning cycles are avaible: a complete cycle

(PYRO) and a shorter cycle (ECO). The complete cycle is best used only in

case of very dirty ovens, while the shorter cycle should be used at regular

intervals.

FAST PREHEATING To preheat the oven rapidly.

FUNCTIONS KNOB (Continued)

EN17

COOKING TABLE

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and

notes

Leavened cakes

Yes 2160-180 30-90 Cake tin on wire shelf

GENTLE

Yes 1-4 160-180 30-90

Shelf 4: cake tin on

wire shelf

Shelf 1: cake tin on

wire shelf

Filled pies

(cheesecake,

strudel, apple pie)

Yes 2160-200 30-85

Drip tray/baking tray

or cake tin on wire

shelf

Yes 1-3 160-200 35-90

Shelf 3: cake tin on

wire shelf (switch

levels halfway

through cooking)

Shelf 1: cake tin on

wire shelf

Biscuits / Tartlets

Yes 2170-180 15-45 Drip tray / baking

tray

GENTLE

Yes 1-4 160-170 20-45

Shelf 4: oven tray on

wire shelf

Shelf 1: drip tray /

baking tray

Choux buns

Yes 2180-200 30-40 Drip tray / baking

tray

GENTLE

Yes 1-4 180-190 35-45

Shelf 4: oven tray on

wire shelf

Shelf 1: drip tray /

baking tray

Meringues

Yes 290 110-150 Drip tray / baking

tray

GENTLE

Yes 1-4 90 130-150

Shelf 4: oven tray on

wire shelf

Shelf 1: drip tray /

baking tray

Bread / Pizza /

Focaccia

Yes 2 190-250 15-50 Drip tray / baking

tray

Yes 1-3 190-250 25-45

Shelf 3: oven tray on

wire shelf (switch

levels halfway

through cooking)

Shelf 1: drip tray /

baking tray

Bread (Bread) Yes 2180-220 30-50 Drip tray / baking

tray or wire shelf

Pizza (Pizza) Yes 2220-250 15-30 Drip tray / baking

tray

EN18

Frozen pizza

Yes 2250 10-15

Shelf 3: drip tray /

baking tray or wire

shelf

Yes 1-3 250 10-20

Shelf 3: oven tray on

wire shelf (switch

levels halfway

through cooking)

Shelf 1: drip tray /

baking tray

Savoury pies (veg-

etable pie, quiche)

Yes 2180-190 40-55 Cake tin on wire shelf

Yes 1-3 180-190 40-55

Shelf 3: cake tin on

wire shelf (switch

levels halfway

through cooking)

Shelf 1: cake tin on

wire shelf

Vols-au-vent / Puff

pastry crackers

Yes 2190-200 20-30 Drip tray / baking

tray

GENTLE

Yes 1-4 180-190 20-40

Shelf 4: oven tray on

wire shelf

Shelf 1: drip tray /

baking tray

Lasagne / Baked

pasta / Cannelloni

/ Flans

Yes 2190-200 45-65 Drip tray or oven tray

on wire shelf

Lamb / Veal / Beef

/ Pork 1 kg Yes 2190-200 70-100 Drip tray or oven tray

on wire shelf

Chicken / Rabbit /

Duck 1 kg Yes 2200-230 50-100 Drip tray or oven tray

on wire shelf

Turkey / Goose

3 kg Yes 1/2 190-200 80-130 Drip tray or oven tray

on wire shelf

Baked fish / en

papillote (fillet,

whole)

Yes 2180-200 40-60 Drip tray or oven tray

on wire shelf

Stuffed vegeta-

bles (tomatoes,

courgettes,

aubergines)

Yes 2180-200 50-60 Oven tray on wire

shelf

Toast - 4 High (3) 2-5 Wire shelf

Fish fillets / steaks - 4 Medium (2) 20-35

Shelf 4: wire shelf

(turn food halfway

through cooking)

Shelf 3: drip tray with

water

Sausages / Kebabs

/ Spare ribs /

Hamburgers

- 4 Medium - High (2-3) 15-40

Shelf 4: wire shelf

(turn food halfway

through cooking)

Shelf 3: drip tray with

water

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and

notes

La page charge ...

Whirlpool 400011543529 Manuel utilisateur

Whirlpool 400011543529 Manuel utilisateur

dans d''autres langues