80024465USCN
Copyright © Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
BRIGGS & STRATTON is a registered
trademark of Briggs & Stratton Corporation.
Revision: A
Not For
Reproduction
Manual Contents:
General Information..............................................................2
Operator Safety.....................................................................2
Features and Controls..........................................................6
Operation...............................................................................8
Maintenance and Adjustment............................................13
Storage.................................................................................16
Troubleshooting..................................................................17
Specifications......................................................................18
General Information
For additional information, refer to the
Customer Contact Guide
and
Setup Instructions
included with the unit.
The illustrations in this document are representative. Your unit
may vary from the images shown.
LEFT
and
RIGHT
are
referenced from the operating position.
The use of Important and Note in the text indicates clarifications,
exceptions, or alternatives to the procedures given.
All language translations of this document are derived from the
original English source file.
All packaging, used oil, and batteries should be recycled
according to applicable government regulations.
Operator Safety
Save these instructions for future reference. This manual
contains safety information to make you aware of the hazards
and risks associated with the product and how to avoid them.
It also contains important instructions that should be followed
during the initial set-up, operation, and maintenance of the
product.
The snowthrower is designed and intended only for clearing of
snow from hard-surface ground-level walkways and driveways
and is not intended for any other purpose.
It is important that you read and understand these instructions
before attempting to start or operate this equipment.
Be thoroughly familiar with the controls and the proper use of
the snowthrower.
Know how to stop the unit and disengage controls quickly.
Safety Alert Symbol and Signal Words
The safety alert symbol identifies safety information about
hazards that can result in personal injury. A signal word
(DANGER, WARNING, or CAUTION) is used with the alert
symbol to indicate the likelihood and the potential severity of
injury. In addition, a hazard symbol may be used to represent
the type of hazard.
DANGER indicates a hazard which, if not avoided, will
result in death or serious injury.
WARNING indicates a hazard which, if not avoided, could
result in death or serious injury.
CAUTION indicates a hazard which, if not avoided, could
result in minor or moderate injury.
NOTICE
indicates an action that could result in damage to the
product.
Snowthrower Hazard Symbols
MeaningSymbolMeaningSymbol
Read and
understand the
operator's
manual before
operating or
servicing the unit.
Safety
information about
hazards that can
result in personal
injury.
Amputation
hazard - rotating
auger.
Remove the key
before performing
service. Read the
operator's
manual before
performing
service.
Thrown objects
hazard.
Amputation
hazard - do not
touch moving
parts.
Explosion
hazard.
Fire hazard
Toxic fume
hazard
Shock hazard
Kickback hazard.Hot surface
hazard.
2
Not For
Reproduction
MeaningSymbolMeaningSymbol
Keep children
away.
Keep a safe
distance
- - -- - -Wear safety
glasses
Safety Messages
DANGER
This snowthrower is capable of amputating hands and feet,
and throwing objects. Read and observe all the safety
instructions in this manual. Failure to do so could result in
death or serious injury.
Hand contact with the rotating auger inside the discharge
chute is the most common cause of injury associated with
snowthrowers.
WARNING
Read, understand, and follow all the instructions on the
snowthrower and in the operator's manual before operating
this unit. Failure to observe the safety instructions in this
manual could result in death or serious injury.
• Only allow operators who are responsible, trained, familiar
with the instructions and physically capable to operate
the machine.
WARNING
Always wear safety glasses or eye shields during operation
or while performing an adjustment or repair to protect eyes
from foreign objects that may be thrown from the machine.
WARNING
U.S.A. Models: Certain components in this product and its
related accessories contain chemicals known to the State of
California to cause cancer, birth defects, or other reproductive
harm. Wash hands after handling.
WARNING
U.S.A. Models: The engine exhaust from this product contains
chemicals known to the State of California to cause cancer,
birth defects, or other reproductive harm.
U.S.A. Models: It is a violation of California Public Resource
Code Section 4442 to use or operate the engine on any
forest-covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as defined
in Section 4442, maintained in effective working order. Other
states or federal jurisdictions may have similar laws. Contact
the original equipment manufacturer, retailer, or dealer to obtain
a spark arrester designed for the exhaust system installed on
this engine.
3
Not For
Reproduction
Safety Decals
To avoid injury, read and understand the safety decals on the
snowthrower before operating it. Match the call out letters in
Figure 1 to the decals listed in the accompanying table. If any
safety decals become worn, damaged, or illegible, contact an
authorized service dealer to order replacements.
1
A
B
4
Not For
Reproduction
C
5
Not For
Reproduction
FeaturesandControls
Match the call out letters in Figure 2 to the features and controls listed in the accompanying table.
2
Control Symbols and Meanings
Auger ControlA
Auger- - -B
Chute Control - Crank- - -C
Deflector Control - Button or Wing KnobD
Starter ButtonE
Electric Starter ReceptacleF
6
Not For
Reproduction
Starting Instructions DecalG
Choke Closed; Choke OpenH
Fuel Tank Cap- - -I
Oil Fill / Dipstick- - -J
Primer ButtonK
ON / OFF SwitchL
Starter Cord Handle- - -M
Oil Drain Plug- - -N
7
Not For
Reproduction
Operation
WARNING
This snowthrower is only as safe as the operator. If it is
misused, or not properly maintained, it can be dangerous.
Remember you are responsible for your safety and those
around you.
• When leaving the operating position always disengage
the auger, turn off the engine, and remove the key. Never
leave a running machine unattended.
• Never operate the snowthrower without proper guards,
and other safety protective devices in place and working.
• Be careful when operating on or crossing gravel drives,
walks, or roads. Stay alert for hidden hazards or traffic.
• Never operate the snowthrower without good visibility or
light. Always be sure of your footing, and keep a firm hold
on the handles. Walk; never run.
• Be careful to avoid slipping or falling, especially when
operating the snowthrower in reverse.
• Be careful when operating on slopes.
• After striking a foreign object, stop the engine, remove
the wire from the spark plug, thoroughly inspect the
snowthrower for any damage, and repair the damage
before restarting and operating the snowthrower.
• Do not operate the equipment without wearing adequate
winter garments. Avoid loose fitting clothing that can get
caught in moving parts. Wear footwear that will improve
footing on slippery surfaces.
• Never touch a hot muffler or engine. Allow muffler and
engine cylinder to cool before touching.
Operating Area
1. Familiarize yourself with the area in which you plan to
operate the snowthrower. Mark off all boundaries of
walkways and driveways.
2. Ensure the area to be cleared is free of debris or objects
that could be picked up by the auger and thrown from the
chute.
WARNING
This machine is capable of throwing objects that could injure
bystanders or cause damage to buildings.
3. Before starting the engine, move the snowthrower outdoors
and away from windows and doors.
WARNING
Engines give off carbon monoxide, an ordorless, colorless,
poison gas. Breathing carbon monoxide can cause nausea,
fainting, or death.
• Start and run engine outdoors.
• Do not run the engine in an enclosed area, even if doors
or windows are open.
4. Ensure the operating area is clear of bystanders, especially
children.
WARNING
This snowthrower is capable of amputating hands and feet,
and throwing objects. Read and observe all the safety
instructions in this manual. Failure to do so could result in
death or serious injury.
• Keep children out of the area during operation.
• Children are often attracted to the equipment. Be mindful
of all persons present.
• Be alert and turn the unit off if bystanders enter the area.
• Use extra care when approaching blind corners, shrubs,
tress, or other objects that may obscure vision.
Starting the Engine
Checking Oil
NOTICE
The engine was shipped from the factory without oil. Before
you start the engine, ensure that you add oil according to the
instructions in this manual. If you start the engine without oil,
it will be damaged beyond repair and will not be covered under
the warranty.
Use Briggs & Stratton Synthetic 5W-30 Warranty Certified oil
for best performance. Other high-quality detergent oils are
acceptable if classified for service SG, SH, SJ or higher. Do
not use any additives.
1. Place the unit on a level surface.
2. Clean the oil fill area of any moisture or debris.
3. Remove the oil dipstick (A, Figure 3) and wipe it with a clean
cloth.
4. Insert and tighten the dipstick, then remove it again to check
the oil level. It should be at the top of the full indicator (C)
5. To add oil, pour slowly into the engine oil fill (B). Do not
overfill.
6. Wait one minute before checking the oil level.
7. When the oil level is at the top of the full indicator (C), install
and tighten the dipstick.
8
Not For
Reproduction
3
Adding Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline
• A minimum of 87 octane / 87 AKI (90 RON)
• Up to 10% ethanol is acceptable
NOTICE
Do not use unapproved gasolines, such as E15 and E85. Do
not mix oil in gasoline or modify the engine to run on alternate
fuels. Use of unapproved fuels will cause engine damage that
will not be covered under warranty.
This engine is certified to operate on gasoline. The emissions
control system for this engine is EM (Engine Modifications).
At altitudes over 5,000 feet (1524 meters), a minimum 85 octane
/ 85 AKI (89 RON) gasoline is acceptable. To remain emissions
compliant, high altitude adjustment is required. Operation without
this adjustment will cause decreased performance, increased
fuel consumption, and increased emissions. See an authorized
service dealer for high altitude adjustment information. Operation
altitudes below 2,500 feet (762 meters) with the high altitude
adjustment is not recommended.
WARNING
Fuel and its vapors are extremely flammable and explosive.
Always handle fuel with extreme care.
Failure to observe these safety instructions can cause a fire
or explosion which could result in serve burns or death.
• Do not add fuel while engine is running. Let the engine
cool at least 2 minutes before adding fuel.
• Fill the fuel tank outdoors only, using an approved fuel
container with the unit directly on the ground.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Allow any spilled fuel to evaporate before starting the
engine.
• If fuel is spilled on clothing change clothing immediately.
1. Slowly remove the fuel cap (A, Figure 4) and fill the tank
(B) with fuel. Do not fill higher than the bottom of the fuel
tank neck (C).
2. Reinstall the fuel cap. Allow any spilled fuel to evaporate
before starting the engine.
4
9
Not For
Reproduction
Starting Engine
WARNING
Fuel and its vapors are extremely flammable and explosive.
Always handle fuel with extreme care.
Failure to observe these safety instructions can cause a fire
or explosion which could result in serve burns or death.
• Ensure that spark plug, muffler, fuel cap, and air cleaner
(if equipped) are in place and secured.
• Do not crank the engine with the spark plug removed.
• Do not use pressurized starting fluids because their
vapors are flammable.
• Do not over-prime the engine. Follow the engine starting
instructions in this manual.
• If the engine floods, set choke (if equipped) to
OPEN/RUN position, move throttle (if equipped) to FAST
position and crank until engine starts.
1. Ensure the auger control is disengaged.
2. Insert the ignition key (A, Figure 5) and turn it to the ON
position or push in the Push/Pull key.
3. Turn the choke control (B) to the Closed position.
Note:
Choke is usually not needed when starting a warm engine.
4. Press the primer (C) two times.
Note:
Primer is usually not needed when starting a warm engine.
5. Rewind start: Firmly hold the starter cord handle (D). Pull
the handle slowly until resistance is felt, then pull rapidly.
WARNING
Rapid retraction of the starter cord (kickback) will pull your
hand and arm toward the engine faster than you can let go.
Broken bones, fractures, bruises, or sprains could result.
5
6. Electric start: Connect the extension cord (E, Figure 6) to
the starter box (F) on the engine and then to the wall
receptacle. Press the starter box pushbutton (G). After the
engine starts, disconnect the extension cord from the wall
receptacle and then from the starter box.
WARNING
Damaged or ungrounded power cords could cause electric
shock. Electric shock could cause severe burns or death.
• Use only a three-conductor power cord properly
grounded to the power source.
• If the extension cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly
qualified person.
NOTICE
To extend the life of the starter, use short starting
cycles (five seconds maximum). Wait one minute between
starting attempts.
If the engine does not start after repeated attempts, contact
an authorized service dealer or go to our website.
7. Allow the engine to warm up for several minutes. Gradually
move the choke control to the Open position.
6
Stopping the Engine
1. Turn the ignition key (A, Figure 5) to the OFF position and
remove it or remove the Push /Pull key, if equipped.
2. Keep the key in a safe place out of the reach of children.
The engine cannot be started without the key.
10
Not For
Reproduction
Adjusting the Discharge Chute and
Deflector
WARNING
Ice, gravel, or other unintended objects can be picked up by
the auger and thrown from the chute with force. Objects thrown
from the chute could cause death, serious injury, or property
damage.
• Always be aware of the direction the snow is being thrown.
NOTICE
Do not use the chute deflector or the chute rotation
handle to lift the unit. These were designed for making needed
adjustment only.
Chute Rotation
1. Rotate the crank (A, Figure 7) in the clockwise direction to
move the discharge chute (B) to the right.
2. Rotate the crank in the counter-clockwise direction to move
the discharge chute to the left.
7
Deflector Adjustment
1. Squeeze and hold the button on the deflector control handle
(D), or loosen the wing knob (E)
2. Move the deflector (C) up or down to adjust the snow
discharge height and distance.
3. Release the button to lock the deflector in the desired
position, or tighten the wing knob.
Engaging the Auger
DANGER
The discharge chute contains a rotating auger to throw snow.
Fingers or feet can quickly become caught in the auger
resulting in traumatic amputation or severe laceration.
Failure to observe these safety instructions will result in
traumatic amputation or severe laceration.
1. Pull the auger control (A, Figure 8) against the handle to
engage the auger.
8
2. Release the auger control to disengage the auger. The
auger must stop within 5 seconds after the auger control is
released. If it does not;
• Adjust the control cable. See Adjusting the Auger
Control Cable.
• If the auger still does not stop within 5 seconds, see an
authorized dealer.
NOTICE
Do not overload the machine capacity by attempting
to clear snow at too fast of a rate.
11
Not For
Reproduction
Clearing a Clogged Discharge Chute
DANGER
The discharge chute contains a rotating auger to throw snow.
Fingers can quickly become caught in the auger resulting in
traumatic amputation or severe laceration. Never clear a
clogged discharge chute with your hands. Always use a
clean-out tool.
To safely clear a clogged discharge chute, follow these
instructions:
1. Stop the engine and remove the key.
2. Ensure that the auger has stopped rotating.
3. Use a clean-out tool to remove snow from the discharge
chute. Never clear a clogged discharge chute with your
hands!
12
Not For
Reproduction
Maintenance and Adjustment
We recommend contacting an authorized service dealer for all
maintenance, adjustments, and servicing of the unit. Some
routine maintenance tasks can be performed by the owner.
Refer to the maintenance schedule and procedures that follow.
CAUTION
All the components used to build this product must remain in
place for proper operation. Replacement parts must be of the
same design and installed in the same position as the orginial
parts. Other parts may not perform as well, may damage the
unit, and may result in injury.
WARNING
This snowthrower must be properly maintained to ensure safe
operation and performance. Failure to observe the safety
instructions in this manual could result in death or serious
injury.
• Before performing any maintenance or repairs on the
snowthrower, shut OFF the engine and remove the ignition
key or the Push/Pull key.
Maintenance Schedule
First 5 Hours
Change oil
Before Each Use
• Check engine oil level
• Check auger stop time
After Each Use
Remove accumulated snow and slush to prevent freezing of the controls,
wheels, discharge chute, and auger
Every 25 Hours or Annually
• Check scraper bar and rubber auger for wear
• Change engine oil
• Check snowthrower for loose hardware
• Check auger control cable adjustment
• Check condition of muffler and muffler guard
• Replace sparkplug (dealer service)
• Check valve clearance* (dealer service)
* Not required unless problems are noted with engine performance.
Emissions Control
Maintenance, replacement, or repair of the emissions control
devices and systems may be performed by any non-road engine
repair establishment or individual. However, to obtain “no
charge” emissions control service, the work must be performed
by a factory authorized dealer.
Changing the Engine Oil
Used oil must be disposed of properly. Do not discard with
household waste. Check with your local authorities, service
center, or dealer for safe disposal or recycling facilities.
Use Briggs & Stratton Synthetic 5W-30 Warranty Certified oil
for best performance. Other high-quality detergent oils are
acceptable if classified for service SG, SH, SJ or higher. Do not
use any additives.
1. With the engine stopped but still warm, turn the ignition key
to the OFF position and remove it or pull out the Push/Pull
key (if equipped).
WARNING
Fuel and its vapors are extremely flammable, which could
cause burns or fire resulting in death or serious injury.
• When performing maintenance that requires the unit to
be tipped, the fuel tank must be empty or fuel can leak
out and result in a fire or explosion.
2. Remove the oil drain plug (D, Figure 9) and tilt the
snowthrower slightly to drain the oil into an appropriate
container.
3. After the oil has drained, install and tighten the oil drain plug
(D).
9
4. Place the unit on a level surface.
5. Clean the oil fill area of any moisture or debris.
6. Remove the dipstick (A, Figure 10) and wipe it with a clean
cloth. Set it aside.
13
Not For
Reproduction
10
7. To add oil, pour slowly into the engine oil fill tube (B). See
Specifications for the oil capacity. Do not overfill.
8. Wait one minute before checking the oil level.
9. Insert and tighten the dipstick, then remove it again to check
the oil level. It should be at the top of the full indicator (C).
10. When the oil level is at the top of the full indicator, install
and tighten the dipstick.
Adjusting the Auger Control Cable
DANGER
The discharge chute contains a rotating auger to throw snow.
Fingers or feet can quickly become caught in the auger
resulting in traumatic amputation or severe laceration.
• Over-tightening the auger cable may cause the auger to
rotate even if the auger control lever is not pressed down.
The auger should rotate only when the auger control is engaged
and must stop within 5 seconds when the auger control is
released. If the auger does not rotate or does not stop as
described, adjust the control cable or contact an authorized
service dealer to adjust the control cable.
1. Shut OFF the engine and remove the ignition key or the
Push/Pull key.
2. Lift the cable cover (A, Figure 11) to expose the adjustment
loops (B) and the cable end fitting (C).
11
3. Remove the end fitting from the adjustment loop and
reinstall as follows:
• If the auger rotates while the auger control is not
engaged, lengthen the control cable by installing the
end fitting in the next lowest loop (decrease belt
tension).
• If the auger does not rotate when the auger control is
engaged, shorten the control cable by installing the end
fitting in the next highest loop (increase belt tension).
Note:
Some slack must remain in the cable when the auger
control is not engaged.
4. Lower the cable cover into place.
5. Check the operation of the auger control using the test
below. If the unit does not operate as described, DO NOT
use it. Contact an authorized service dealer to have the unit
inspected and adjusted or repaired.
Testing the Auger Control
With the engine running:
• Press down and hold the auger control lever. The auger
should rotate.
• Release the auger control lever. The auger must stop
within 5 seconds.
Maintaining the Auger and Scraper Bar
1. Shut OFF the engine and remove the ignition key or the
Push/Pull key.
2. Check the wear limit on the rubber auger (A, Figure 12) and
the gap between the scraper bar support and the ground
(B).
14
Not For
Reproduction
• If the wear limit on the rubber auger is reached, the two
rubber flights need replacing. Contact an authorized dealer.
• If the scraper bar support makes contact with the ground,
the scraper bar needs replacing. Contact an authorized
dealer.
12
15
Not For
Reproduction
Storage
At the end of the season, or whenever the unit will be stored for
30 days or more, follow the storage checklist below.
WARNING
Gasoline is highly flammable and its vapors are explosive.
Fumes may travel to a distant ignition source and an explosion
and/or fire could result.
• If there is fuel in the tank, do not store the unit indoors or
in a poorly ventilated area where fumes could reach
sparks, open flames, pilot lights, heat, and other ignition
sources.
Engine:
Fuel can become stale when stored more than 30 days. Stale
fuel can cause acid and gum deposits to form in the fuel system
and the carburetor. To keep fuel fresh, add Briggs & Stratton
Advanced Formula Fuel Treatment & Stabilizer.
• There is no need to drain the fuel from the engine if a
stabilizer is added according to instructions. Run the engine
for 2 minutes to circulate the stabilizer throughout the fuel
system. If no stabilizer is added, the fuel must be drained
from the engine into an approved container. Then run the
engine until it stops from lack of fuel.
• While the engine is still warm, change the oil. See Changing
the Engine Oil.
Snowthrower:
• Ensure all nuts, bolts, and screws are securely fastened.
• Inspect all external moving parts for damage and wear.
Replace parts as necessary.
• For unpainted or bare metal surfaces, apply a rust
preventative product.
• Store the unit indoors and cover it.
• If the unit must be stored outdoors, cover it with a heavy
tarpaulin.
Returning the Unit to Service:
• Have an authorized service dealer perform annual
maintenance tasks. See Maintenance Schedule.
• Check the engine oil level and add oil if necessary.
• Remove any debris around the muffler and cylinder areas.
• Fill the fuel tank with fresh, clean fuel.
• Ensure all guards, shields, and covers are in place.
• Test the auger control.
16
Not For
Reproduction
Troubleshooting
SolutionCauseProblem
See
Adjusting the Auger Control Cable
.Control cable requires adjustmentAuger does not stop when auger control is
released
See
Adjusting the Auger Control Cable
.Control cable requires adjustmentAuger does not turn when auger control is
engaged
Turn key to the ON position.Key is offEngine does not start
Press primer button twice before pulling starter rope.Primer not pressed
Fill fuel tank with fresh fuel.Out of fuel
Turn choke to closed position before pulling starter
rope.
Choke open - cold engine
Turn choke to open position; pull starter rope several
times until engine starts.
Engine flooded
Fill fuel tank with fresh fuel.Water in fuel or old fuel
Plug in cord or replace defective cord; reset circuit
breaker.
Cord not plugged in or circuit breaker tripped (electric
start models)
Clear snow or ice from chute and deflector parts;
place snowthrower in a heated area until snow or ice
melts.
Chute or deflector is frozenChute rotation or deflector adjustment does not
work
Change oil to lighter viscosity (such as 5W-30).Incorrect oilEngine is hard to start or runs poorly
Open choke control gradually as engine warms up.Choke control set incorrectly
Stop snowthrower immediately. Contact an
Authorized Service Dealer.
Loose parts or damaged partsExcessive vibration
See
Maintaining the Auger and Scraper Bar
.Scraper bar or auger flight wornScraper bar does not clean hard surface
See
Adjusting the Auger Control Cable
.Control cable requires adjustmentSnowthrower does not discharge snow
STOP THE ENGINE! Ensure that the auger has
stopped rotating. Use a clean-out tool to remove
snow from the discharge chute. Never clear a clogged
discharge chute with your hands! See
Clearing a
Clogged Discharge Chute
.
Discharge chute clogged with snow
See
Maintaining the Auger and Scraper Bar
.Rubber auger is worn or damagedSnowthrower does not self-propel
For all other issues, please see an authorized dealer.
17
Not For
Reproduction
Specifications
Specifications Chart
The spark ignition system on this snowthrower complies with Canadian standard ICE-002.
Model 150000Model 130000Item
Briggs & StrattonBriggs & StrattonEngine Brand
Snow SeriesSnow SeriesEngine Model Series
4-Cycle4-CycleEngine Type
Recoil Start and Electric StartRecoil Start and Electric StartStarting System
20 oz (,59 L)20 oz ( ,59 L)Oil Capacity
3.2 qts (3,0 L)3.0 qts (2,8 L)Fuel Tank Capacity
.030 in (,76 mm).030 in (,76 mm)Sparkplug Gap
180 lb-in (20 Nm)180 lb-in (20 Nm)Sparkplug Torque
.010 - .014 in (,25 - ,36 mm).010 - .014 in (,25 - ,36 mm)Armature Air Gap
.004 - .006 in (,10 - ,15 mm).004 - .006in (,10 - ,15 mm)Intake Valve Clearance
.009 - .011 in (,23 - ,28 mm).006 - .008 in (,15 - ,20 mm)Exhaust Valve Clearance
Power Ratings
The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive Engineers)
code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower values are
derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments. Actual gross
engine power will be higher than net engine power and is affected by, among other things, ambient operating conditions and
engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine may not develop
the rated gross power when used in a given piece of power equipment. This difference is due to a variety of factors including,
but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel pump, etc.), application
limitations, ambient operating conditions (temperature, humidity, altitude), and engine-to-engine variability. Due to manufacturing
and capacity limitations, Briggs & Stratton may substitute an engine of higher rated power for this engine.
18
Not For
Reproduction
Índice de contenidos:
Información general............................................................19
Seguridad del operador......................................................19
Características y controles................................................23
Operación.............................................................................25
Mantenimiento y ajustes.....................................................30
Bodegaje..............................................................................33
Detección de fallas..............................................................34
Especificaciones.................................................................35
Información general
Para obtener información adicional, consulte la
Guía de
contactos del cliente
y las
Instrucciones de instalación
que se
incluyen con la unidad.
Las ilustraciones que aparecen en este documento son
representativas. Su unidad puede diferir de las imágenes que
se muestran.
Izquierda (LEFT)
y
derecha (RIGHT)
se
referencian a partir de la posición de funcionamiento.
El empleo de las palabras "Importante" y "Nota" en el texto
indica aclaraciones, excepciones o alternativas a los
procedimientos proporcionados.
Todas las traducciones de este documento se derivan del
archivo fuente original en inglés.
Todos los envases, el aceite usado y las baterías deben
reciclarse de acuerdo con las regulaciones gubernamentales
aplicables.
Seguridad del operador
Guarde estas instrucciones para futura referencia. Este
manual contiene información sobre seguridad para hacer que
tome consciencia de los peligros y riesgos asociados con el
producto y cómo evitarlos. También contiene importantes
instrucciones que deben seguirse durante la configuración
inicial, la operación y el mantenimiento del producto.
La máquina quitanieves está diseñada exclusivamente para la
limpieza de nieve de senderos y caminos de acceso de
superficies rígidas y niveladas, y no está destinada para ningún
otro propósito.
Es importante que lea y comprenda estas instrucciones antes
de intentar arrancar u operar este equipo.
Procure estar familiarizado con los controles y el uso adecuado
de la máquina quitanieves.
Aprenda cómo detener la unidad y desactivar los controles
rápidamente.
Símbolo de alerta de seguridad y palabras
de señalización
El símbolo de alerta de seguridad identifica información
de seguridad sobre riesgos que pueden provocar lesiones
personales. Se usa una palabra de señalización (PELIGRO,
ADVERTENCIA, o ATENCIÓN) junto con el símbolo de alerta
para indicar la probabilidad y la gravedad potencial de las
lesiones. Además, se puede usar un símbolo de peligro para
representar el tipo de riesgo.
PELIGRO indica un riesgo que, si no se evita, ocasionará
la muerte o lesiones graves.
ADVERTENCIA indica un riesgo que, si no se evita, podría
ocasionar la muerte o lesiones graves.
ATENCIÓN indica un riesgo que, si no se evita, podría
ocasionar lesiones menores o moderadas.
AVISO
indica una acción que podría provocar daños al
producto.
Símbolos de peligro de la máquina
quitanieves
SignificadoSímboloSignificadoSímbolo
Lea y entienda el
Manual del
operador antes
de operar o
reparar la unidad.
Información de
seguridad sobre
los riesgos que
pueden provocar
lesiones físicas.
Peligro de
amputación:
Barrena giratoria.
Quite la llave
antes de realizar
el servicio. Lea el
Manual del
operador antes
de realizar el
servicio.
Peligro de
objetos lanzados.
Peligro de
amputación: no
toque las piezas
móviles.
Peligro de
explosión.
Peligro de
incendio
Peligro de
emisión de
vapores tóxicos
Peligro de
descarga
19
Not For
Reproduction
SignificadoSímboloSignificadoSímbolo
Peligro de
retroceso
violento.
Peligro de
superficie
caliente.
Mantenga a los
niños alejados.
Mantenga una
distancia segura.
- - -- - -Use gafas de
seguridad.
Mensajes de seguridad
PELIGRO
Esta máquina quitanieves es capaz de amputar manos y pies,
y arrojar objetos. Lea y siga todas las instrucciones de
seguridad incluidas en este manual. Omitir esto podría tener
como consecuencia la muerte o lesiones graves.
El contacto manual con la barrena giratoria dentro de la
manga de descarga es la causa más común de lesiones
asociadas con la máquina quitanieves.
ADVERTENCIA
Lea, comprenda y siga todas las instrucciones que se
encuentran en la máquina quitanieves y en el Manual del
operador antes de operar la unidad. El incumplimiento de las
instrucciones de seguridad incluidas en este manual podría
resultar en la muerte o lesiones graves.
• Solo permita que operadores responsables, capacitados,
familiarizados con las instrucciones y físicamente aptos
operen la máquina.
ADVERTENCIA
Utilice siempre gafas de seguridad o protectores oculares
durante el funcionamiento o mientras realice un ajuste o una
reparación para proteger los ojos de objetos extraños que
puedan ser lanzados de la máquina.
ADVERTENCIA
Modelos de EE. UU.: Determinados componentes de este
producto y los accesorios relacionados contienen sustancias
químicas reconocidas en el estado de California por producir
cáncer, defectos de nacimiento u otros daños que pueden
ser perjudiciales para la reproducción. Lávese las manos
después de manipular estos elementos.
ADVERTENCIA
Modelos de EE. UU.: El escape del motor de este producto
contiene sustancias químicas reconocidas en el estado de
California por producir cáncer, defectos de nacimiento u otros
daños que pueden ser perjudiciales para la reproducción.
Modelos de EE. UU.: Es una violación del Código de Recursos
Públicos de California, Sección 4442, utilizar u operar el motor
en cualquier espacio con árboles, maleza o grama a menos
que el sistema de escape esté equipado con un extintor de
chispas, como lo define la Sección 4442, mantenido en correcto
funcionamiento. Otros estados o jurisdicciones federales pueden
tener leyes similares. Póngase en contacto con el vendedor, el
distribuidor o el fabricante del equipo original para obtener un
extintor de chispas diseñado para el sistema de escape
instalado en este motor.
20
Not For
Reproduction
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Briggs & Stratton 1696727 Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Briggs & Stratton 1696727 User manual
- español: Briggs & Stratton 1696727 Manual de usuario
- português: Briggs & Stratton 1696727 Manual do usuário