CMF95 SERIES 95.1 AFUE
DOWNFLOW, SINGLE STAGE CONDENSING GAS FURNACE
WARNING AVERTISSEMENT
FIRE OR EXPLOSION HAZARD
• Failure to follow safety warnings exactly could
result in serious injury or property damage.
• Installation and service must be performed
by a qualified installer, service agency or the
gas supplier.
• Do not store or use gasoline or other
flammable vapors and liquids in the vicinity
of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not
use any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbors phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call
the fire department.
RISQUE D’INCENDIE OU D’EXPLOSION
• Le non-respect des avertissements de sécurité
pourrait entraîner des blessures graves ou des
dommages matériels.
• L’installation et l’entretien doivent être effectués
par un installateur qualifié, un organisme de
service ou le fournisseur de gaz.
• Ne pas entreposer ni utiliser de l’essence ni
d’autres vapeurs ou liquides inflammables
dans le voisinage de cet appareil, ni de tout
autre appareil.
QUE FAIRE S’IL Y A UNE ODEUR DE GAZ
• Ne tenter d’allumer aucun appareil.
• Ne toucher à aucun interrupteur électrique;
n’utiliser aucun téléphone dans le bâtiment.
• Évacuer l’immeuble immédiatement.
• Appeler immédiatement le fournisseur de gaz en
employant le téléphone d’un voisin. Respecter
les instructions du fournisseur de gaz.
• Si personne ne répond, appeler le service des
incendies.
DO NOT DESTROY. PLEASE READ CAREFULLY & KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
NE PAS DÉTRUIRE. VEUILLEZ LIRE ATTENTIVEMENT ET CONSERVER EN UN LIEU SÛR POUR RÉFÉRENCE ULTÉRIEURE.
IMPORTANT! Please read all information in this manual
thoroughly and become familiar with the capabilities and use
of your appliance before attempting to operate or maintain this
unit. Pay attention to all safety warnings and any other special
notes highlighted in the manual.
Keep this literature where you have easy access to it in the
future. If a problem occurs, check the instructions and follow
recommendations given. If these suggestions don’t eliminate your
problem, call your servicing contractor. Under no circumstances
should the appliance owner attempt to install and/or service
this equipment.
Some local codes require licensed installation / service personnel
for this type of equipment. Improper service, adjustment, or
maintenance may cause explosion, fire, electrical shock or
other hazardous conditions which may result in personal injury
or property damage.
USER’S MANUAL
For Furnaces Installed in: Manufactured Homes, Modular Homes/Buildings, Recreational Vehicles, Park Models, & Manufactured Buildings
2
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION ........................... 3
FLOOD DAMAGE .......................................................... 3
GAS SUPPLY & PIPING ................................................ 3
VENTING SYSTEM ....................................................... 4
CLEARANCES TO COMBUSTIBLES ............................ 4
SHUTTING DOWN THE FURNACE .............................. 4
GENERAL INFORMATION .............................................. 5
ABOUT THE FURNACE ................................................ 5
AIR FILTERS ................................................................. 5
THERMOSTAT .............................................................. 5
FURNACE IN A SMALL ROOM OR CLOSET ............... 5
SOURCES OF CORROSION ........................................ 5
WARRANTY INFORMATION ........................................ 5
MAINTENANCE INFORMATION ..................................... 6
BLOWER & FILTER ....................................................... 6
CONDENSATE DRAINAGE .......................................... 6
FURNACE & AIR DUCTS .............................................. 6
VENTING SYSTEM ....................................................... 6
TROUBLESHOOTING ..................................................... 6
STARTUP & SHUTDOWN ............................................... 7
STARTING THE FURNACE .......................................... 7
SHUTTING DOWN THE FURNACE .............................. 7
FURNACE COMPONENTS ............................................. 8
3
IMPORTANT NOTE:
If the unit needs to be shut down for an extended period of
time, turn off both the gas and electrical power. For your
safety always turn off both the gas and electrical power before
performing service or maintenance on the furnace. If the gas
supply to the unit must be shut off, refer to the shut down
instructions on page 7.
GAS SUPPLY & PIPING
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use
any phone in your building.
• Leave the building immediately.
• Immediately call your gas supplier from a
neighbors phone. Follow the gas suppliers
instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed by a qualified
installer, service agency or the gas supplier.
QUE FAIRE S’IL Y A UNE ODEUR DE GAZ
• Ne tenter d’allumer aucun appareil.
• Ne toucher à aucun interrupteur électrique; n’utiliser aucun
téléphone dans le bâtiment.
• Évacuer l’immeuble immédiatement.
• Appeler immédiatement le fournisseur de gaz en employant
le téléphone d’un voisin. Respecter les instructions du
fournisseur de gaz.
• Si personne ne répond, appeler le service des incendies.
WARNING:
All gas piping and shutoff valves must be installed in
compliance with local codes and utility regulations
by licensed installers. DO NOT attempt to modify, or
tap into existing gas lines yourself. Fire or explosion
may result causing property damage, personal injury
or loss of life. Failure to follow the safety warnings
exactly could result in serious injury, death or property
damage.
WARNING:
The furnace was shipped from the factory equipped
to operate on natural gas. Conversion to LP/propane
gas must be performed by a licensed HVAC technician
using a factory supplied conversion kit. Failure to use
the proper conversion kit can cause fire, explosion,
property damage, carbon monoxide poisoning,
personal injury, or death.
This furnace does not have a pilot. It is equipped with an ignition
device which automatically lights the burner. DO NOT light the
burner by hand.
Safety markings are used frequently throughout this manual to
designate a degree or level of seriousness and should not be
ignored. WARNING indicates a potentially hazardous situation that
if not avoided, could result in personal injury or death. CAUTION
indicates a potentially hazardous situation that if not avoided, may
result in minor or moderate injury or property damage.
WARNING:
To avoid possible equipment damage, fire, or
personal injury, the following instructions must be
observed regarding unit maintenance and operational
procedures.
WARNING:
PROPOSITION 65 WARNING: This product contains
chemicals known to the state of California to cause
cancer, birth defects or other reproductive harm.
• To achieve optimum performance and minimize equipment failure,
it is recommended that periodic maintenance be performed on
this unit. The ability to properly perform maintenance on this
equipment requires certain mechanical skills and tools. Please
consult your dealer for maintenance information and availability
of maintenance contracts.
• The area around the gas furnace (Figure 1, page 4) and the
vicinity of any other gas appliances must be kept clear and free
of combustible materials, gasoline, and other flammable vapors
and liquids. Do not store or use flammable items such as paint,
varnish, or strippers in the vicinity of the unit.
• Do not use the area around the unit as a storage area. This area
must be kept clean and clear of loose or exposed insulation
materials. Examine the unit’s area when it is installed or when
insulation is added, since some insulation materials may be
combustible.
FLOOD DAMAGE
WARNING:
Do not use this furnace if any part has been under
water. A flood damaged furnace is extremely
dangerous. Attempts to use the furnace can result in
fire or explosion. A qualified service agency should
be contacted to inspect the furnace and to replace all
gas controls, control system parts, electrical parts that
have been wet or the furnace if deemed necessary.
AVERTISSEMENT:
Ne pas installer ce générateur d’air chaud si l’une de ses pièces a
été immergée dans de l’eau. Un générateur d’air chaud endommagé
par une inondation est extrêmement dangereux. Toute tentative
d’utiliser le générateur d’air chaud peut entraîner un incendie
ou une explosion. Il faut communiquer avec un organisme de
service qualifié pour l’inspection du générateur d’air chaud et le
remplacement de toutes pièces électriques ou parties du système
de commande qui ont été mouillées ou immergées.
• Familiarize yourself with the controls that shut off the gas and
electrical power to the unit.
IMPORTANT SAFETY INFORMATION
4
• Air openings on top of the furnace and openings in closet doors
or walls must never be restricted. If the furnace is operated
without adequate air for combustion, the flame roll-out switch will
open, turning off the gas supply to the burners. This indicates
that a serious problem with the burners has occurred and must
be corrected immediately. Only a licensed HVAC technician can
reset this switch.
• Your furnace and its venting system should be inspected annually
by a licensed HVAC technician. The filter should be inspected at
least once a month. See also the Maintenance Instructions on
pages 6 - 7.
• Before you remodel a room near the furnace, consult with a local
code official or the National Fuel Gas Code to make sure you
will be in compliance with supplying adequate air for combustion.
By erecting new walls, it is sometimes possible to inadvertently
restrict the furnace’s air supply. You can find more information
about supplying combustion air in the NFGC, which is available
at many libraries.
CLEARANCES TO COMBUSTIBLES
The furnace is designed to have certain clearances to combustible
items such as wood, paper, etc. Some types of insulation are
combustible. If your furnace is installed in an attic, near unfinished
walls, or in other insulated space, keep area surrounding the furnace
free of insulating material.
WARNING:
Do not place combustible materials on or against the
furnace cabinet or vent pipe. The area around the
furnace must be kept clear and free of combustible
materials, gasoline and other flammable vapors and
liquids. A fire or explosion may result causing property
damage, personal injury or loss of life. Failure to follow
the safety warnings exactly could result in serious
injury, death or property damage.
IMPORTANT NOTE:
Should the gas supply fail to shut off or if overheating occurs,
shut off the gas valve to the furnace before shutting off the
electrical supply!
En cas de température excessive, ou s’il est impossible de couper
l’alimentation en gaz, fermer le robinet manuel d’alimentation en gaz du
générateur d’air chaud avant de couper l’alimentation électrique
VENTING SYSTEM
WARNING:
CARBON-MONOXIDE POISONING HAZARD
Failure to folow instructions could result in severe
personal injury or death due to carbon-monoxide
poisoning if combustion products infiltrate into
the building.
Check that all oepnings in the outsdie wall around
the vent (and air intake) pipe(s) are sealed to prefent
infiltration of combustion products into the building.
Check that furnace vent (and air intake) terminal(s)
are not obstructed in any way during all seasons.
AVERTISSEMENT :
RISQUE D’INTOXICATION AU MONOXYDE
DE CARBONE
Si ces directives ne sont pas suivies, cela peut entraîner
des blessures graves ou une intoxication au monoxyde de
carbone pouvant causer la mort, si des produits de combustion
s’infiltrent dans le bâtiment.
Vérifier que toutes les ouvertures pratiquées dans le mur
extérieur autour du ou des tuyaux d’évent (et de la prise d’air)
sont scellées de manière à empêcher l’infiltration de produits
de combustion dans le bâtiment.
Veiller à ce que la ou les sorties de l’évent de l’appareil
de chauffage (et la prise d’air) ne soient, en aucune façon,
obstruées, quelle que soit la saison
WARNING:
It is extremely important that the furnace receives an
unobstructed flow of clean, fresh air to properly burn
the fuel gas. If this flow of air is restricted, the partially
burned combustion gases may create dangerous
amounts of carbon monoxide - a colorless, odorless
gas that is a deadly poison that can cause personal
injury or death. This could create the production of
excessive amounts of Carbon Monoxide - a colorless,
odorless gas that is a deadly poison that could result
in serious personal injury or death.
Do not block any openings that are supplying fresh air
to the room or closet the furnace is in. Your furnace
obtains its air through a pipe to the outdoors, do not
allow the inlet of the pipe to become blocked.
• For proper and safe operation, this furnace requires unrestricted
airflow for combustion and ventilation. Do not block or obstruct air
openings on the furnace, air openings around the furnace area
or the spacings around the furnace.
SHUTTING DOWN THE FURNACE
If you need to shut down your furnace for service or maintenance,
shut off the gas valve to the furnace before shutting off the electrical
service. Remove the door panel from the front of the furnace and
turn the knob to the OFF Position. Additional instructions for shutting
down the furnace can be found on page 7. If your installation has a
manual gas shutoff valve on the gas supply pipe, shut this off, then
shut off the electric to the furnace.
Figure 1. Minimum Clearances
CLEARANCES TO COMBUSTIBLE MATERIALS*
LEFT
SIDE
FRONT
RIGHT
SIDE
REAR
VENT
Sides....................... 0 Inches
Front ........................1 Inch
Top ..........................6 Inches
Rear ........................ 0 Inches
Vent ........................ 0 Inches
5
ABOUT THE FURNACE
• This furnace has been tested for capacity and efficiency in
accordance with A.H.R.I. Standards and will provide many years
of safe and dependable comfort, providing it is properly installed
and maintained. With regular maintenance, this unit will operate
satisfactorily year after year. Abuse, improper use, and/or improper
maintenance can shorten the life of the appliance and create
unsafe hazards.
• This furnace is designed to fulfill the requirements of being
classified as a Category IV furnace. This classification is related
to the furnace’s Annual Fuel Utilization Efficiency (AFUE) rating,
the percentage of fuel that is converted into usable heating energy.
• Category IV furnaces typically have an AFUE rating over 90%
and are mainly vented through plastic PVC pipe.
AIR FILTERS
WARNING:
Never operate the furnace without a filter in place.
Accumulating dust in the return air can build up on
internal components, resulting in loss of efficiency,
equipment damage, and possible fire.
• An air filter is supplied with the furnace as shipped from the
factory.
• The furnace should always have a clean filter. If the filter becomes
dirty, it should be cleaned or replaced. The filter is installed over
the return air grille of the door inside the furnace cabinet.
• New or newly renovated homes may require more frequent
changing or cleaning until the construction dust has minimized.
Filters designed to remove smaller particles such as pollen, may
require additional maintenance.
THERMOSTAT
• Single stage gas furnaces (M7RL series) are designed to be
controlled by a conventional single stage thermostat. Two-stage
gas furnaces (M7TL series) will perform best with a conventional
two-stage thermostat. However, it is possible to control the M7TL
furnace with a single stage thermostat. Consult with your installer
about which type is best for your installation. Both thermostats
are commonly available at your local building supply store.
• The thermostat’s wiring must comply with the current provisions of
the NEC (ANSI/NFPA 70) and with applicable local codes having
jurisdiction. Thermostat connections should be made according
to the instructions supplied with the thermostat and the indoor
equipment.
• The thermostat should be mounted about 5 feet above the floor
on an inside wall and not on an outside wall or other location
where its operation may be adversely affected by radiant heat
from fireplaces, sunlight, or lighting fixtures, and convective heat
from warm air registers or electrical appliances.
• Thermostat styles vary. Please refer to the thermostat
manufacturer’s User Manual for detailed programming instructions.
FURNACE IN A SMALL ROOM OR CLOSET
If a furnace is installed in relatively small utility room or closet, the
installation needs openings in the walls or door to let return air
in. Make sure that these openings remain unobstructed. Do not
modify these openings in any way without consulting a licensed
HVAC technician.
SOURCES OF CORROSION
It is known that certain common household chemicals can cause
heat exchanger corrosion if the vapors are pulled into the furnace’s
burners The following is a list of chemicals that should not be used
or stored near the furnace.
Do not store these chemicals near the furnace:
• Gasoline/Kerosene
• Permanent wave solutions
• Chlorinated waxes and cleaners
• Chlorine based swimming pool chemicals
• Water softening chemicals
• De-icing salts or chemicals
• Carbon tetrachloride
• Halogen type refrigerants
• Cleaning solvents (perchloroethylene)
• Printing inks, paint removers, varnishes, etc.
• Hydrochloric acid
• Cements and glues
• Antistatic fabric softeners
• Masonry acid washing materials
WARRANTY INFORMATION
A warranty certificate with full details is included with the equipment.
Carefully review these responsibilities with your dealer or service
company. The manufacturer will not be responsible for any costs
found necessary to correct problems due to improper setup, improper
installation, adjustments, improper operating procedure on the part
of the user, Some specific examples of service calls which are not
included in the limited warranty are:
• Correcting wiring problems in the electrical circuit supplying the
equipment.
• Resetting circuit breakers or other switches.
• Adjusting or calibrating of thermostat.
GENERAL INFORMATION
6
Proper maintenance is important to achieve optimum performance from the furnace. This equipment should be inspected annually by
a licensed HVAC technician. Table 1 (page 7) contains suggested inspections and frequency of maintenance. Routine maintenance
should include the following:
BLOWER & FILTER
• Never operate the furnace without a filter in place. Dust and lint
can build up on internal components, resulting in loss of efficiency,
equipment damage, and possible fire.
• Keep air filters cleaned. Filters should be changed or cleaned
monthly during the heating/cooling season. Clean or replace filter
to maintain proper airflow and achieve maximum efficiency. Newly
built or renovated homes may require more frequent changing
until the construction dust has minimized. Filters designed to
remove smaller particles such as pollen, may require additional
maintenance.
• It is recommended that the blower compartment be cleaned of
dirt or lint that may have accumulated in the compartment or on
the blower and motor as part of the annual inspection.
CONDENSATE DRAINAGE
• This furnace produces liquid condensate which is slightly acidic.
The vent pipe must be sloped upwards away from the furnace
to properly drain the water back into the condensate disposal
system.
• Condensate drain tubes must maintain a downward slope to
ensure proper drainage. Periodically inspect the condensate
drain tube for proper drainage. Also, do not place heavy objects
on the tubing that restricts the flow of condensate.
FURNACE & AIR DUCTS
• Homeowners should perform frequent visual inspections of the
furnace for obvious signs of deterioration. The furnace should be
sound without sagging, cracks gaps, etc around the base. The
return air duct connection(s) is secured and sealed to the furnace
cabinet and terminates outside the area containing the furnace.
Any signs of damage or loose connections should be repaired
by a qualified HVAC technician.
• Furniture and drapery should be arranged so that the supply air
registers and return grilles are not obstructed.
• If house is newly built, the operation of a gas furnace in a
construction environment can cause a variety of problems with
the furnace. Before occupying the residence, homeowners should
have these safety inspections performed by a licensed technician:
– The filter must be replaced (or cleaned) and the furnace must be
inspected by a licensed HVAC technician.
– The furnace must be cleaned and/or repaired if found to be dirty,
damaged, or malfunctioning in any way.
– Before occupancy, the furnace shall be inspected and approved
by applicable local authority even if this results in redundant
inspections.
– The duct work must be inspected and cleaned if found to contain
any construction debris.
VENTING SYSTEM
• For proper and safe operation, the furnace needs air for combustion
and ventilation. Do Not block or obstruct air openings on the
furnace, or any air openings where the furnace may be installed,
including any surrounding spaces.
• Direct vent furnaces pull combustion air from the outdoors and
vent combustion products back outside. Combustion air coming
from the outside needs to be clean of chemicals that can cause
corrosion, such as pool chlorinating products.
• Vent pipe must slope upwards and be physically sound without
holes or corrosion. Any corroded section of vent pipe must be
replaced, and any obstruction or blockage must be removed by
a licensed HVAC technician.
• Flue passageways, the vent system, and the burners should be
inspected and cleaned (if required) by a licensed HVAC technician
annually to ensure continued safe operation.
If the furnace fails to operate check the following:
1. Is the thermostat setting correct?
2. Is the ON / OFF switch inside the front door turned on? See
Figure 3 (page 8) for switch location.
3. Is the circuit breaker tripped?
4. Is the gas turned on at the manual shutoff?
5. Is the filter dirty or clogged?
If the furnace still doesn’t operate, contact a licensed HVAC technician
MAINTENANCE INFORMATION
TROUBLESHOOTING
7
STARTING THE FURNACE
1. Make sure the filter is clean and in place.
2. Make sure the vent system is properly installed.
3. Set the thermostat to the lowest setting.
4. Close the manual gas valve outside the furnace.
5. Turn off all electric to the furnace.
6. Remove the door from the burner compartment.
7. Set the gas valve On/Off knob to the OFF position.
See Figure 2 for gas valve knob location.
8. Wait 5 minutes. If there is any smell of gas, see “WHAT TO DO
IF YOU SMELL GAS” on page 3.
9. Set the gas valve On/Off knob to the ON position.
10. Turn on all electric to the furnace, including the ON / OFF switch.
See Figure 3 (page 8) for switch location.
11. Open the manual gas valve.
12. Turn the thermostat back up to force ignition.
13. Observe operation, including burners. If burners fail to ignite,
call a licensed HVAC technician.
14. Replace the door on the burner compartment.
SHUTTING DOWN THE FURNACE
If you need to shut down your furnace for service or maintenance,
follow these steps:
1. Set the thermostat to the lowest setting.
2. Close the manual gas valve outside the furnace.
3. Turn electric to the furnace off.
4. Open the door to the burner compartment.
5. Set the ON /OFF switch to OFF. See Figure 3 (page 8) for switch
location.
6. Set the gas valve On/Off knob to the OFF position. See Figure
2 below for knob location.
7. Replace the door on the burner Compartment.
Figure 2. Gas Valve
ON / OFF Knob
OFF Position
ON Position
Table 1. Maintenance Table
MAINTENANCE ITEM
FREQUENCY OF MAINTENANCE
BEGINNING OF EACH
HEATING SEASON
END OF EACH
HEATING SEASON
MONTHLY
Verify furnace area is free of combustible materials X X X
Verify combustion and ventilation air is not restricted X X X
Verify no signs of physical deterioration of the furnace X X X
Verify no obstructions or restrictions in vent or chimney X X
Verify no holes or cracks in vent pipe X X
Verify no corrosion in vent pipe X X
Verify the horizontal vent pipes slope upwards away from the furnace X X
Clean or replace filter(s) X
MAINTENANCE ITEMS BELOW SHOULD BE PERFOMED BY QUALIFIED SERVICE PERSON.
Verify burner flame X
Clean blower compartment X
Clean burner assembly X
Clean condensate collection & disposal system (if applicable) X
STARTUP & SHUTDOWN
The furnace components shown in Figure 3 will help identify and locate various parts of the furnace. The component you need to
familiarize yourself with is the gas valve. You will use this to turn the furnace on and off. There are no user serviceable parts. All repairs
must be done by a licensed HVAC technician.
Figure 3. CMF95 Furnace Components
Blower Assembly
Inducer Assembly
Gas Valve
Gas Manifold &
Burner Assembly
ON / OFF Switch
Control Board
Limit Switch
Inline Drain
Assembly
24V Tr ansformer
Igniter
Main Air Limit Switch
Flame Sensor
Roll-Out Switch
Combustion Air Pipe
Exhaust Vent Pipe
Specifications & illustrations subject to change without notice or incurring
obligations (04/18). O’Fallon, MO, © Nortek Global HVAC LLC 2018.
All Rights Reserved.
709439A
(Replaces 7094390)
FURNACE COMPONENTS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Miller CMF95 User manual
Documents connexes
-
Miller CMF95 Manuel utilisateur
-
-
-
-
Miller M7RL Manuel utilisateur
-
-
Miller M7TL Manuel utilisateur
-
-
-