Maytag DF6SE 10/31/2011 Manuel utilisateur

Marque: Maytag

Modèle: DF6SE 10/31/2011

Taper: Manuel utilisateur

Ce manuel convient également à

User’s Information Manual

Single Package Gas Heating/Electric Cooling Unit

FOR YOUR SAFETY:

WARNING: If the information in this

manual is not followed exactly, a fire

or explosion may result causing prop-

erty damage, personal injury, or loss

of life.

Do not store or use gasoline or other

flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in your building.

• Immediately call your gas supplier from

a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier,

call the fire department.

Installation and service must be per-

formed by a qualified installer, service

agency, or the gas supplier.

IMPORTANT:

Read this owner information thoroughly before attempting to operate or maintain this unit

to become familiar with the capabilities and use of your appliance. Keep this literature where

you have easy access to it in the future. If a problem occurs, check the instructions and follow

recommendations given. If these suggestions don’t eliminate your problem, call your

NORDYNE Servicing Contractor (Service PRO).

Any additions, changes, or conversions required in order for the appliance to satisfactorily

meet the application needs must be made by a qualified installer, service agency, or the gas

supplier using factory specified and approved parts.

GENERAL INFORMATION

This gas heating/electric cooling unit has been

designed and built to provide many years of safe

and dependable home comfort, providing it is

properly installed and maintained. With regular

maintenance, this unit will operate satisfactorily

year after year. Abuse, improper use, and/or

improper maintenance can shorten the life of

the appliance and create hazards for you. Please

read this manual carefully to familiarize yourself

with operation, maintenance, and safety proce-

dures for this unit.

A regular service and maintenance schedule

should be established to ensure efficient and

safe operation of the unit. See the “system

maintenance” section at the end of this manual

for proper procedures and schedules.

Be sure that the thermostat is properly installed

and is not being affected by drafts or heat from

lamps or other appliances.

WARNING:

To avoid possible equipment dam-

age, fire, or death, the following in-

structions must be observed regard-

ing unit location, combustion air re-

quirements, and operation proce-

dures.

Gas Heating/Electric Cooling

Unit Location

The area around the gas heating/electric cool-

ing unit and the vicinity of any other gas appli-

ances must be kept clear and free of combus-

tible materials, gasoline, and other flammable

vapors and liquids. Do not store or use flam-

mable items such as paint, varnish, or strippers

in the vicinity of the unit.

Do not use the area around the unit as a storage

area. This area must be kept clear and clean.

The unit must also be kept clear of loose or

exposed insulation materials. Examine the

unit’s area when it is installed or when insulation

is added, since some insulation materials may

be combustible.

Do not use this appliance if any part has been

under water. Immediately call a qualified ser-

vice technician to inspect the unit and to replace

any part of the control system and any gas

control which has been under water.

Familiarize yourself with the controls that shut

off the gas and electrical power to the unit. If the

unit is to be shut down for an extended period of

time, turn off both the gas and electrical power.

For your safety always turn off both the gas and

electrical power before performing service or

maintenance on the furnace.

Combustion Air Supply

The gas heating/electric cooling unit needs an

adequate supply of combustion and ventilation

air for proper and safe operation. Do not block

or obstruct air openings on the unit or air open-

ings supplying the area where it is installed.

If the unit is operated with inadequate combus-

tion air supply, the flame roll-out control switch

located above the burners will open, turning off

the gas supply to the burners. The flame roll-out

control is a manual-reset device. DO NOT

install a jumper wire across this switch to defeat

its function. DO NOT reset the control without

identifying and correcting the fault condition

which caused the control to trip. If this switch

must be replaced, use only the replacement

part specified in the accompanying Replace-

ment Parts List.

All air openings in the door of the unit, warm air

registers, and return air grilles must not be

restricted.

CAUTION:

Combustion air must not be drawn

from a corrosive atmosphere.

To maximize heat exchanger life, the combus-

tion air must be free of chemicals which form

corrosive acidic compounds in the combustion

gases. Some examples of these chemicals are

chlorine, fluorine, and sulphur. Some common

sources of these chemicals are detergents,

bleaches, aerosol sprays, cleaning solvents,

and a wide variety of commercial and household

products.

Ductwork

WARNING:

Failure to prevent products of com-

bustion from being circulated into the

living space can create potentially

hazardous conditions including car-

bon monoxide poisoning that could

result in personal injury or death.

The duct connections must be physically sound

and sealed to the unit’s casing to prevent prod-

ucts of combustion from entering the living

space.

The return air and circulating air ductwork must

not be connected to any other heat producing

device such as a fireplace insert, stove, etc.

Doing so may result in fire, explosion, personal

injury, carbon monoxide poisoning, or property

damage.

OPERATING INSTRUCTIONS

Cooling Operation

1. Set the thermostat system switch to COOL

and the thermostat fan switch to AUTO.

(See Figure 1)

2. Set the thermostat temperature selector to

the desired temperature level. Some ther-

mostat models will have two temperature

selectors, one marked “C” to set the de-

sired cooling temperature, and a second

marked “H” to set the desired heating tem-

perature. The outdoor fan, compressor,

and indoor blower will all cycle on and off to

maintain the indoor temperature at the

desired cooling level.

NOTE: If the thermostat temperature level

is readjusted, or the thermostat system

switch is repositioned, the outdoor fan and

compressor may not start immediately. The

unit contains a protective timer circuit which

holds the unit off for approximately six

minutes following a previous operation or

the interruption of the main electrical power.

Figure 1. Typical Thermostat

FAN SWITCH

TEMPERATURE

SELECTOR

SYSTEM SWITCH

TEMPERATURE SCALES

Knob (Robinet)

Figure 2

1. Mettre le thermostat à la position minimale.

2. Débrancher l’appareil en prévision de la réparation.

3. Retirer le panneau/volet d’accès de commande (panneau supérieur

s’il s’agit d’un modèle à deux panneaux).

4. Faire tourner le robinet à gaz dans le sens des aiguilles d’une

montre

pour l’amener sur la position OFF (Arrêt) Ne pas

forcer (Voir Figure 2).

5. Remettre le panneau/volet d’accès de commande en place

(panneau supérieur s’il s’agit d’un modèle à deux panneaux).

1. ATTENTION! Lire d'abord la liste des mesures de sécurité cidessus.

2. Mettre le thermostat à la position minimale.

3. Couper le courant électrique qui mène à l’appareil.

4. Cet appareil ménager étant doté d’un système d’allumage automatique,

ne pas essayer d'allumer le brûleur manuellement.

5. Retirer le panneau/volet d’accès de commande (panneau supérieur s’il

s’agit d’un modèle à deux panneaux).

6. Faire tourner le robinet à gaz dans le sens des aiguilles d’une montre

pour l’amener sur la position OFF (Arrêt) (Voir Figure 2).

7. Attendre cinq (5) minutes pour s’assurer de la dissipation du gaz. En

cas d’odeur, ARRÊTER LE PROCÉDÉ. Suivre les instructions ci-

dessus (Section B). En l’absence de toute odeur de gaz, avancer à

l’étape suivante.

8. Faire tourner le robinet à gaz dans le sens inverse des aiguilles d’une

montre

pour l’amener sur la position ON (Marche) (Voir Figure 2).

9. Remettre le panneau/volet d’accès de commande en place (panneau

supérieur s’il s’agit d’un modèle à deux panneaux).

10. Rebrancher l’appareil sur le réseau électrique.

11. Ajuster le thermostat à la position désirée.

12. Si l’appareil ne fonctionne pas, suivre les “Directives d’arrêt” cidessous

et appeler le technicien de service.

1. STOP! Read the safety information above on this label.

2. Set the thermostat to the lowest setting.

3. Turn off all electrical power to the appliance.

4. The appliance’s ignition device automatically lights the burner. Do not

try to light burner by hand.

5. Remove the control access door/panel (upper door if two-door

model).

6. Move the gas control knob clockwise

to “OFF”. (See Figure 2)

7. Wait five (5) minutes to clear out any gas. Then smell for gas,

including near the floor. If you smell gas, STOP! Follow “B” in above

information. If you don’t smell gas, go to the next step.

8. Move the gas control knob counterclockwise

to “ON”.(See

Figure 2)

9. Replace the control access

door/panel (upper door if

two-door model).

10. Turn on all electrical power

to the appliance.

11. Turn the thermostat to

desired setting.

12. If the appliance will not operate, follow the instructions “To Turn Off

Gas To Appliance” and call your service technician or gas supplier.

WARNING:

If you do not follow these

instructions exactly, a fire or explosion may

result causing property damage, personal

injury, or loss of life.

1. Set the thermostat to the lowest setting.

2. Turn off all electrical power to the appliance if service is to be

performed.

3. Remove the control access door/panel (upper door if two-door

model).

4. Move the gas control knob clockwise

to “OFF”. Do not use

force. (See Figure 2)

5. Replace the control access door/panel (upper door if two-door

model).

MODE D'EMPLOI

DIRECTIVES D’ARRÊT

A. This appliance does not have a pilot. It is equipped with an ignition

device which automatically lights the burner. Do

not try to light the

burner by hand.

B. BEFORE OPERATING smell all around the appliance area for gas.

Be sure to smell next to the floor because some gas is heavier than

air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in or turn the gas control knob. Never

use tools. If the knob will not push in or move by hand, do not try to

repair it, call a qualified service technician. Force or attempted repair

may result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immedi-

ately call a qualified service technician to inspect the appliance and to

replace any part of the control system and any gas control which has

been under water.

OPERATING INSTRUCTIONS

A. Cet appareil ménager n'a pas de veilleuse. II est doté d’un

système d’allumage automatique. Ne pas essayer d'allumer le

brûleur manuellement.

B. AVANT L’USAGE. Attention à une possible odeur de gaz surtout

au niveau du plancher où les gaz les plus lourds ont la tendance de

se concentrer.

EN CAS D’ODEUR DE GAZ.

• Ne mettre en marche aucun appareil électrique.

• Ne toucher à aucun commutateur électrique, ne pas employer

le téléphone.

• Quitter le bâtiment immédiatement et avertir la compagnie du

gaz en utili sant le téléphone d'un voisin.

• A défaut de la compagnie du gaz, avertir le service des

pompiers.

C. Enfoncer ou faire tourner le robinet à gaz à la main seulement. Ne

jamais utiliser d'outils. S’il n’est pas possible de faire tourner ou

d’enfoncer le robinet à la main, ne pas essayer de le réparer. Faire

appel à un spécialiste. Forcer ou tenter de réparer le robinet

pourrait être à l’origine d’une explosion ou d’un incendie.

D. II est déconseillé d’utiliser cet appareil en contact prolongé avec

l’eau. Faire inspecter ou remplacer toute commande par un

technicien qualifié si un des systèmes de contrôle du gaz s'est

trouvé sous l'eau.

ATTENTION!

L’inobservation de ces

instructions peut entraîner un incendie ou une

explosion pouvant causer des dammages à

votre propriété à votre personne, ou la mort.

POUR VOTRE SÉCURITÉ.

À LIRE AVANT L’EMPLOI

FOR YOUR SAFETY

READ BEFORE OPERATING

TO TURN OFF

GAS TO APPLIANCE

Heating Operation

1. Set the thermostat system switch to Heat

and the thermostat fan switch to AUTO.

(See Figure 1)

2. Set the thermostat temperature selector to

the desired temperature level. Some ther-

mostat models will have two temperature

selectors, one marked “C” to set the de-

sired cooling temperature, and a second

marked “H” to set the desired heating tem-

perature. The indoor blower and heating

module blower will cycle on and off to

maintain the indoor temperature at the

desired heating level.

WARNING:

Should overheating occur, or the gas

supply fail to shut off, shut off the

manual gas valve to the unit before

shutting off the electrical supply.

NOTE: This unit is equipped with a manual-

reset flame roll-out limit switch. This switch acts

to verify that the burner flame is being drawn into

the heat exchanger tubes. If the flame is not

being drawn into the tubes, the flame roll-out

switch will open within several seconds. When

this switch opens, the gas valve will de-ener-

gize, which will stop the flow of gas. Further-

more, both the combustion inducer and the

circulating air blower will energize and continue

to operate until the switch is closed. Do not reset

the flame roll-out switch before identifying and

correcting the fault condition that caused the

switch to open. If the switch will not reset or

continues to open, immediately contact a quali-

fied serviceman to identify and repair the prob-

lem.

System Shutdown

Set the thermostat system switch to OFF and

the thermostat fan switch to AUTO (See Figure

1). The system will not operate, regardless of

the thermostat temperature selector(s) setting.

To Operate the Indoor Blower

Continuously

Set the thermostat fan switch to ON (may be

called CONT on some thermostat models). (See

Figure 1)

The indoor blower will start immediately, and

will run continually until the fan switch is reset to

AUTO.

The continuous indoor blower operation can be

obtained with the thermostat system switch set

in any position, including OFF.

The continuous indoor blower operation is typi-

cally used to circulate the indoor air to equalize

a temperature unbalance due to a solar load,

cooking, or fireplace operation.

System Maintenance

CAUTION:

Be certain the electrical power to the

unit is disconnected and the gas is

shut off before doing the following

recommended maintenance.

Proper maintenance is most important to achieve

the best performance from the appliance and

should be performed by a qualified service

technician at least once a year. Follow the

maintenance schedule and the instructions be-

low for years of safe, trouble free operation.

Do not place combustible materials on or

against the cabinet.

Do not store gasoline or any other flam-

mable vapors and liquids in the vicinity of

the unit.

Annually inspect the physical support of the

furnace to ensure that it is physically sound

without sagging, cracks, gaps, etc., around

the base so as to provide a seal between

the support and the base.

Annually inspect the return-air connection

to ensure that it is physically sound and is

still sealed to the casing of the unit.

Annually inspect the unit, ductwork, and

vent system for signs of physical deteriora-

tion.

Always replace the doors on the unit after

servicing or cleaning/changing the filters.

Do not operate the unit without all doors

and covers in place.

Avoid operating the unit when windows and

doors are open.

Be sure that the thermostat is properly

installed and is not being affected by drafts

or heat from lamps or other appliances.

son, the beginning of every cooling season, and

when an accumulation of dust and dirt are

visible on the filter. IMPORTANT: Replace

disposable filter(s) installed in your system only

with the same size dimensional filters that are

being replaced. Clean permanent filter(s) as

described by the manufacturer of your particular

permanent filter.

Motor Lubrication:

WARNING:

Lubrication of the motors in this unit

is not required. Do not lubricate any

motor in this product.

The motors for the circulating air blower, out-

door fan, and combustion blower are pre-lubri-

cated at the factory. No further oiling is required

for the life of this product.

Burner Maintenance:

CAUTION:

Some components in the burner ves-

tibule are at high temperatures while

the burners are operating. Use cau-

tion to avoid personal injury.

Check the burner flames at the start of every

heating season. Set the thermostat to a tem-

perature setting above the room temperature.

Remove the control access panel to the unit and

visually inspect the burner assembly to make

sure that the flame is drawn directly into the

center of the heat exchanger tube (See Figure

3). In a properly adjusted burner assembly, the

flame bends up and to the left at the end of the

heat exchanger tube, and the end of the flame

will be out of sight around the bend. The flame

color should be blue, however some light yellow

streaks may occur on the outer portions of the

flame.

Refer to Table 1 for complete maintenance

schedule.

Regular Cleaning:

Remove any leaves and grass clippings from

the outdoor coil, being careful not to damage the

aluminum fins.

Check for any obstructions, such as twigs, sticks,

etc.

CAUTION:

Do not strike any of the internal elec-

trical components while vacuuming.

Clean the blower compartment monthly during

the heating and cooling seasons to remove any

dirt and lint that may have accumulated in the

compartment or on the blower and motor.

Buildup of dirt and lint on the blower and motor

can create excessive loads on the motor result-

ing in higher than normal operating tempera-

tures and possible shortened service life.

Air Filters:

WARNING:

Never operate the unit without a filter

in the return air system. Dust and lint

in the return air can build up on the

internal components, resulting in a

loss of efficiency, equipment dam-

age, and possible fire risk.

This unit is not supplied with air filter(s) and has

no means for accommodating internal air filter(s).

The installer is responsible for installing a filtra-

tion system into the return air duct of this sys-

tem. The filter(s) of this system should be

checked at least monthly.

It is very important to replace or clean the

filter(s) installed in the return air duct of this

system. A clogged filter could cause airflow

related problems and reduce the overall effi-

ciency of your unit. Depending upon which type

of filter was installed with your unit, clean (per-

manent) or replace (disposable) filter(s) of your

system at the beginning of every heating sea-

MAINTENANCE ITEM

BEGINNING OF BEGINNING OF EACH

EACH HEATING SEASON COOLING SEASON MONTHLY

VERIFY AREA AROUND UNIT IS FREE

OF COMBUSTIBLE MATERIALS

VERIFY COMBUSTION AND VENTILATION

AIR ARE NOT RESTRICTED

XXX

VERIFY THERE ARE NO SIGNS OF PHYSICAL

DETERIORIZATION OF THE UNIT

XXX

VERIFY BURNER FLAME

INSPECT UNIT SUPPORT

INSPECT RETURN-AIR CONNECTIONS

CLEAN OR REPLACE FILTER

(

)

CLEAN BLOWER COMPARTMENT

CLEAN BURNER VESTIBULE

FREQUENCY OF MAINTENANCE

Table 1. Maintenance Schedule

Before Calling A Technician:

If the unit fails to operate in cooling, be certain

of the following:

1. The thermostat is operating properly. Refer

to “Cooling Operation.”

2. The electrical power to the unit is turned on.

3. The filters are not dirty.

If the unit fails to operate in heating, be certain

of the following:

1. The thermostat is operating properly. Refer

to “Heating Operation.”

2. The electrical power to the unit is turned on.

3. The gas is turned on.

4. The filters are not dirty.

Figure 3. Burner Inspection

¢708258E¤

7082580

O’Fallon, MO

7082580 (Replaces 707621A)

Specifications and illustrations subject to change

without notice and without incurring obligations.

Printed in U.S.A. (03/03)

Maytag DF6SE 10/31/2011 Manuel utilisateur

Marque: Maytag

Modèle: DF6SE 10/31/2011

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Maytag DF6SE 10/31/2011 User manual

Maytag DF6SE 10/31/2011 Manuel utilisateur

Ce manuel convient également à

Maytag DF6SE 10/31/2011 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents