Simplicity 071038-00 Manuel utilisateur

100/200 Amp Automatic

Transfer Switch

with AC Power Control Module™

Installation & Operator’s Manual

Questions?

Help is just a moment away!

Call: Transfer Switch Helpline

800-743-4115 M-F 8-5 CT

195114

Revision G

2 BRIGGSandSTRATTON.COM

Thank you for your purchase of this Briggs & Stratton® Power Products automatic transfer switch. This product is designed

for use with specific home standby generators and may not function with generators produced by other manufacturers. Seek

a qualified electrical professional to determine applicability of this equipment to generators manufactured by others. When

operated and maintained according to the instructions in this manual, your power management system will provide many years

of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to

avoid them. We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation

is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be

achieved. We do not know all possible hazards and/or the results of each possible method or procedure. It is important that

you read and understand these instructions thoroughly before attempting to install or operate this equipment. Save these

original instructions for future reference.

This transfer switch requires professional installation before use. Refer to the Installation section of this manual for

instructions on installation procedures. Only licensed electrical contractors should install transfer switches. Installations must

strictly comply with all applicable federal, state and local codes, standards and regulations. Your installer should follow the

instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages. There

are many authorized service dealers who provide quality service. You can also contact Technical Service by phone at

800-743-4115 between 8:00 AM and 5:00 PM CT, or on the Internet at BRIGGSandSTRATTON.COM.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Model Number _______________________________

Revision _________

Serial Number _______________________________

Date Purchased _______ / _________ / ____________

3

Table of Contents

Important Safety Instructions ...........................4

Installation ...........................................5

Owner Orientation ...............................................5

Installing Dealer/Contractor Responsibilities .........................5

Mounting Guidelines .............................................6

Power Wiring Interconnections ....................................7

System Setup .................................................10

Controls ............................................11

Operation ...........................................11

Testing the Automatic Transfer Switch .............................11

Maintenance.........................................12

Troubleshooting .....................................13

Schematic Diagram, 071038 .....................................14

Wiring Diagram, 071038.........................................15

Schematic Diagram, 071055 .....................................16

Wiring Diagram, 071055.........................................17

Product Specifications ................................18

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the equipment unsafe.

Save These Instructions

Electrical Shock

Read Manual

NOTICE Only qualified electricians should attempt

installation of this equipment, which must strictly comply

with applicable codes, standards and regulations.

WARNING Certain components in this product and

related accessories contain chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING Shock Hazard. Installing low and high

voltage wire in same conduit could result in

death, serious injury and/or property damage.

• Do not run low and high voltage wire in the same conduit

unless the insulation rating on ALL wiring is rated for

600V. See NEC for more information.

WARNING Failure to properly ground equipment

could cause electrocution resulting in death or

serious injury.

• Do not touch bare wires.

• Do not use equipment with worn, frayed, bare or

otherwise damaged wiring.

• Do not handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand

on an insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service equipment.

• In case of an accident caused by electrical shock,

immediately shut down all sources of electrical power

and contact local authorities. Avoid direct contact with

the victim.

NOTICE Improper treatment of equipment could damage

it and shorten its life.

• Use equipment only for intended uses.

• If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.

• Do not expose equipment to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off

their circuit breaker/fuse.

WARNING Equipment contains high voltage that

could cause electrocution resulting in death or

serious injury.

• Despite the safe design of the system, operating this

equipment imprudently, neglecting its maintenance or

being careless could result in death or serious injury.

5

Installation

We sincerely appreciate your patronage. For this reason, we

have made significant effort to provide for a safe, streamlined

and cost-effective installation. Because each installation is

unique, it is impossible to know of and advise the trade of all

conceivable procedures and methods by which installation

might be achieved. Neither could we know of possible

hazards and/or the results of each method or procedure.

For these reasons, only current licensed electrical

professionals should attempt system installations.

Installations must strictly comply with all applicable

codes, industry standards and regulations.

Your equipment is supplied with this combined Installation

and Operator’s Manual. This is an important document and

should be retained by the owner after the installation has

been completed.

Every effort has been made to make sure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the system at any time without prior notice.

Home Owner Responsibilities

To help you make informed choices and communicate

effectively with your installation contractor(s), read and

understand Owner Orientation before contracting or

starting your equipment installation.

To arrange for proper installation, contact the store at which

you purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is

installed by licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and

are meant to familiarize you with the installation options

available with your system.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must be

allowed for. This is necessary to comply with local codes and

overcome electrical voltage drops.

These factors will have a direct effect on the overall

price of your equipment installation.

Your installer must check local codes AND obtain permits

before installing the system.

• Read and follow the instructions given in this manual.

• Follow a regular schedule in caring for and using your

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

• Read and observe the safety rules.

• Read and follow the instructions given in this manual.

• The installer may need to provide appropriate rated

contactors based on loads to be controlled.

• Check federal, state and local codes and authority

having jurisdiction, for questions on installation.

• Ensure generator is not overloaded with selected loads.

If you need more information about the transfer switch, call

800-743-4115, between 8:00 AM and 5:00 PM CT.

Equipment Description

The transfer switch is designed to transfer selected loads

found in normal residential installations to generator power

in the event of a utility power failure. The load is connected

either to utility power (normal) or home standby power

(generator). The transfer switch monitors utility and generator

voltages and will automatically connect to the appropriate

source of power.

Major components of the transfer switch are a 2 pole

double throw transfer switch, control circuit board, fused

utility terminals and interconnecting wiring. The control

board also has two inputs for current transformers that

sense generator current. These components are housed in

a NEMA 3R enclosure that is suitable for both indoor and

outdoor installations.

The transfer switch is solenoid-operated from utility or

generator inputs and contain suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It

has ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided for

the transfer function.

The control board has active circuits sensing utility and

generator voltages. It creates a signal for generator start-up,

switch transfer and retransfer when utility is restored. The

control board also contains red and green LED’s indicating

the power sources available and two relay operated contacts

that provide supervisory control of external loads.

6 BRIGGSandSTRATTON.COM

Delivery Inspection

After opening the carton, carefully inspect the transfer

switch components for any damage that may have occurred

during shipment.

If loss or damage is noted at time of delivery, have the

person(s) making delivery note all damage on the freight bill

and affix his signature under the consignor’s memo of loss or

damage. If loss or damage is noted after delivery, contact the

carrier for claim procedures. Missing or damaged parts are

not warranted.

Shipment contents

• Automatic transfer switch (1)

• Installation and Operator’s Manual (1)

• Current transformers (2)

To be supplied by installer:

• Connecting wire and conduit

• Various specialty tools/equipment

Mounting Guidelines

The system circuitry is enclosed in a NEMA Type 3R

enclosure suitable for indoor/outdoor use. Guidelines for

mounting the enclosure include:

• Install enclosure on a firm, sturdy supporting structure.

• The enclosure must be installed with minimum

NEMA 3R hardware for conduit connections.

• To prevent switch contact distortion, level and plumb

the enclosure. This can be done by placing washers

between the enclosure and the mounting surface.

• NEVER install the switch where any corrosive

substance might drip onto the enclosure.

• Protect the switch at all times against excessive

moisture, dust, dirt, lint, construction grit and

corrosive vapors.

A typical automatic transfer switch installation is depicted

below. It is best if the transfer switch is mounted near

the utility meter, either inside or outside. Discuss layout

suggestions/ changes with the owner before beginning the

system installation process.

NOTICE Before drilling conduit entry holes, or any other

holes, cover and protect the switch and electronics to prevent

dirt and metal fragments from entering the mechanical and

electrical components. Failure to do so may result in damage

or malfunction of the switch.

NOTICE Use a vacuum to clean any dirt or metal

shavings inside the transfer switch. Do not use a blower or

compressed air to clean the inside of the transfer switch

because debris may become lodged in the electrical and

mechanical components causing damage or malfunction.

Main

Distribution

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Disconnect

Switch

Generator

Watt -

Hourmeter

Branch

Circuits

Branch Circuits

— — — — — — Control Wiring

Sub-panel

7

Power Wiring Interconnections

NOTICE All wiring must be the proper gauge, properly

supported and protected by conduit. All wiring should be done

per applicable federal, state and local codes, standards and

regulations. Obey wire type and torque specifications printed on

the terminal blocks, neutral/ground connectors, and installation

instructions. Approved for copper and aluminum wiring.

Complete the following connections between the transfer

switch, main distribution panel, generator and sub-panel.

Use installer-supplied 300VAC or greater wire that complies

with Table 310.16 in the National Electric Code. Apply the

necessary correction factors and wire size calculations.

1. Set generator’s circuit breaker to OFF (open) position.

2. Set generator’s system switch to OFF position and

remove 15 Amp fuse from system control panel.

3. Ensure utility power to the standby generator and

transfer switch is disconnected.

4. Using installer supplied 300VAC or greater conductor, connect

utility power from a suitably-rated two pole breaker installed in

main distribution panel to transfer switch contactor terminals

marked “UTILITY”. Ensure circuit breaker is turned OFF.

5. Using installer supplied 300VAC or greater conductor,

connect main distribution panel ground to transfer

switch “GROUND” bus.

Assure grounding electrode conductor is connected

and bonded per applicable federal, state and local

codes, standards and regulations.

6. Using installer supplied 300VAC or greater conductor,

connect main distribution panel neutral conductor (A) to

transfer switch “NEUTRAL” terminal. (B) will be neutral

to sub-panel. (C) will be neutral to generator.

7. Using installer supplied 300VAC or greater conductor,

connect transfer switch contactor terminals marked

“LOAD” to sub-panel.

8. Using installer supplied 300VAC or greater conductor,

connect transfer switch “GROUND” terminal to sub-

panel ground bus.

9. Using installer supplied 300VAC or greater conductor,

connect transfer switch “NEUTRAL” terminal (B, above)

to sub-panel neutral bus.

10. Using installer supplied 300VAC or greater conductor,

connect transfer switch contactor terminals marked

“GENERATOR” to generator circuit breaker LINE1 and

LINE2 terminals. Each conductor must pass through hole

of current transformer inside transfer switch enclosure.

11. Plug current transformer leads into “CT1” and “CT2”

terminals on transfer switch control board.

12. Using installer supplied 300VAC or greater conductor,

connect transfer switch “NEUTRAL” terminal to

generator “NEUTRAL” terminal. Observe generator

control panel labeling for terminal identification.

33

240V

11

22

44

11

22

44

120V

0

Neutral

Ground

To Transfer Switch

Line 1 Neutral

Ground

Line 2

Circuit

Breaker

WARNING Shock Hazard. Installing low and high

voltage wiring in same conduit could result in

death, serious injury and/or property damage.

• Do not run low and high voltage wiring in the same

conduit unless the insulation rating on ALL wiring is rated

for 600V AND the length of the conduit is 30 ft. or less.

See NEC for more information.

NOTICE Improper installation could cause damage to the

circuit boards and shorten their life. Installing circuit boards in live

circuits will damage the board and is not covered by warranty.

ALWAYS disconnect ALL sources of power prior to servicing.

• Remove all power prior to installing this equipment. Failure

to do so could cause internal damage to the board when

making electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the standby generator and

transfer switch.

A

B

C

8 BRIGGSandSTRATTON.COM

13. Using installer supplied 300VAC or greater conductor,

connect transfer switch “GROUND” terminal to

generator control panel “GROUND” terminal.

Assure generator equipment grounding conductor is

connected per applicable federal, state and local codes,

standards and regulations.

14. Using installer supplied 300VAC or greater minimum

#14 AWG conductor, connect transfer switch “UTILITY

240 VAC” terminals to generator’s “240 VAC” terminals

via two-pin connector supplied with generator.

15. Using installer supplied 300 volt 75°C-90°C, #18 AWG

twisted pair conductors, no greater than 200 ft in length,

connect “T/R” and “GND” terminals on transfer switch

control board (B) to the generator’s control panel (A)

“TxRx” and “TxRx GND” terminals via ten-pin connector

supplied with generator.

16. Tighten all wire connections/fasteners to proper torque.

See label inside transfer switch enclosure for proper

torque values. Replace all protective barriers.

Supervisory Control Wiring

An air conditioner can be used with the supervisory contacts

on either terminals A-A or B-B. Terminals A-A can only be

used with supervisory control. Large loads can only be used

with contactor control on terminals B-B. Examples of each

system are described below.

1. The terminal strip on the transfer switch control board

has four connections for customer use. There are two

sets of “Normally Closed” contacts available. They will

be activated when generator power is required. These

can be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator power available.

For installer convenience, there are two wireways

provided to help keep supervisory load wires organized.

2. Terminals “A-A” on transfer switch control board are rated

for 24 VAC. Connect these contacts in series between air

conditioner thermostat and air conditioner contactor.

3. Terminals “B-B” on transfer switch control board are

rated for 1 Amp 125 VAC. When connected with an

installer supplied contactor, it can be used to control a

large load, such as an electric water heater. Contacts are

connected in series with the contactor control circuit.

4. Tighten all wire connections/fasteners to proper torque. See

label inside transfer switch enclosure for proper torque values.

The illustration on the following page shows a typical

installation. Your actual layout will vary. Illustration callouts are:

A - From utility watt-hour meter

B - Neutral bus

C - Main distribution panel

D - Transfer switch disconnect circuit breaker

E - T/R and GND to Generator

F - Transfer switch control board

G - Supervisory contacts

H - Neutral terminal

J - Sub-panel

K - Ground bus

L - UTILITY 240VAC to Generator

M - Two-pin connector

N - Ten-pin connector

O - Generator

P - Generator Neutral terminal

R - Generator circuit breaker

S - Generator Ground terminal

T - Current transformers

V - Transfer switch ground terminal

W - LOAD connection

X - GENERATOR connection

Y - UTILITY connection

Z - Transfer switch

B

Contactor

Neutral

120 VAC

A

B

A

To air conditioner contactor

From air conditioner thermostat

24 VAC

9

S1

S2

N

G

L1

L2

N

G

E1

E2

N

240

VAC

G

E1

E2

N

L1

L2

N

A

D

E

F

H

T

Y

Z

L

W

K

V

G

C

B

J

X

N

R

O

P

M

S

K

10 BRIGGSandSTRATTON.COM

System Setup

You must perform the following before operating the system:

• If generator is installed in an area regularly subjected

to temperatures below 40°F (4°C), select a 50 second

warm up time by moving jumper JP2 (A) installed

on transfer switch control board from ‘20’ position to

‘50’ position.

• Set the DPSW1 (B) and DPSW2 (C) dipswitches

on the transfer switch control board to match the

kW rating of the standby generator, as described in

Setting Dipswitches.

Setting Dipswitches

Dipswitches are used to adjust control board operation

based on generator capacity. DPSW1 and DPSW2 switches

are set to correspond to total system kW rating. Dipswitch

DPSW1 (B) has units of 1,000 watts; Dipswitch DPSW2 (C)

has units of 10,000 watts.

Set dipswitches with utility and generator power removed

from the transfer switch to ensure proper control system

operation. If dipswitches are set when power is present at

transfer switch, a power reset needs to be performed before

the new dipswitch settings will take effect. Power reset is

when all power is removed from the transfer switch and then

reintroduced after 30 seconds.

NOTICE An FC_8 will occur on standby generator control board

if dipswitches are not properly established as noted above.

The “ON” position for the dipswitches is the switch number ON

THE TRANSFER SWITCH CONTROL BOARD, not on the

switch. For example, for an 18,000 watt generator, set DPSW2

dipswitch 10 to “ON” position. Set DPSW1 dipswitch 8 to “ON”

position. 10,000 plus 8000 equals 18,000 watts.

Set only one

switch to “ON” position on DPSW1 and DPSW2.

Refer to following chart for proper switch selection(s).

NOTICE

Air density is less at high altitudes, resulting in

less available engine power. Specifically, engine power will

decrease 3.5% for each 1,000 feet (300 meters) above sea

level and 1% for each 10° F (5.6°C) above 77°F (25°C).

Generators located in these conditions must have the transfer

switch programmed appropriately for this power decrease.

System Test

With the generator system switch in AUTO, turn the circuit

breaker feeding the transfer switch to the OFF position. After

a few minutes the generator will start and the transfer switch

will transfer essential loads to generator power.

To return to utility power, turn the circuit breaker feeding the

transfer switch ON.

NOTICE Use extreme caution when setting dipswitches or

damage to control board will result.

• Use a pencil or small piece of plastic to set the dipswitch.

• NEVER use a screwdriver or any type of metal object to

set dipswitches.

DPSW

1

DPSW2

JP2

kW Rating

of

Generator

DPSW

#1 “ON”

Position

DPSW

#2 “ON”

Position

7kW 7 0

8kW 8 0

9kW 9 0

10kW* 0 10

11kW* 1 10

12kW 2 10

13kW* 3 10

14kW 4 10

15kW 5 10

16kW 6 10

17kW 7 10

18kW 8 10

19kW 9 10

20kW 0 20

30kW 0 30

45kW 5 40

48kW 8 40

50kW 0 50

60kW 0 60

* For generators with a rating that includes 500 Watts, round down to

next lowest rating

(example: 13.5 kW set to 13kW)

B

C

A

11

Controls

There are no operator controls because this device is an

automatic transfer switch. The detachable maintenance

handle is to be used only by licensed professionals.

Information on handle use can be obtained by calling

Technical Service at 800-743-4115.

Operation

To select automatic transfer operation, do the following:

1. Set circuit breaker in main distribution panel feeding

transfer switch to “ON” position.

2. Install 15 Amp fuse in generator’s control panel.

3. Set generator’s circuit breaker to “ON” position.

4. Set generator’s system switch to “AUTO” position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer switch,

the transfer switch control board is constantly monitoring

generator power. If the air conditioner is called to run, and

there is sufficient generator power available, the controller

will close contacts “A-A” to air conditioner contactor.

Contacts “B-B” will open before contacts “A-A” close. If loads

are too great for the generator, contacts “A-A” and/or “B-B”

will open. When air conditioning is not needed, A-A will open.

If enough power is available, “B-B” will close.

NEMA 3R Enclosure Door

To open door, press the spring-load door lock to the right

and pull down on the door.

To close and latch door, push door closed against enclosure.

While in this position, push door upwards. This will cause

spring-load door lock to engage and latch door in place.

Enclosure door MUST be closed and latched at all times

except when system is being serviced.

Testing the Automatic Transfer Switch

Turn the main distribution panel breaker feeding the transfer

switch to the “OFF” position. The system’s automatic

sequence will initiate. To return to utility power, turn the main

distribution panel breaker to the “ON” position.

Utility Fail

The generator senses when utility voltage is below

70 percent of nominal. Engine start sequence is initiated after

6 second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer. Use

jumper on transfer switch control board to select delay of

20 seconds or 50 seconds.

Transfer

Transfer from utility to generator supply occurs after voltage

is above set levels. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility power is approximately

10 seconds after utility voltage supply is above pickup level

and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

12 BRIGGSandSTRATTON.COM

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visual inspections should be done at least once a month.

Access to transfer switch must not be obstructed. Keep

3 feet (92 cm) clearance around transfer switch. Check

for an accumulation of dirt, moisture and/or corrosion

on and around the enclosure, loose parts/hardware,

cracks and/or discoloration to insulation, and damaged or

discolored components.

Exercise the transfer switch at least once every three months

as described in Testing the Automatic Transfer Switch unless

a power outage occurs and home generator system has

gone through an automatic sequence. Allow generator to run

for at least 30 minutes.

Contact a licensed electrical professional to inspect and

clean the inside of the enclosure and other components of

your home generator system at least once a year.

When Calling for Assistance

You must have the Model Number and Serial Number from

the unit ID label at hand if it is necessary to contact a local

service center regarding service or repair of this unit. Obtain

this information from the unit ID label located on or inside

the enclosure.

To contact Briggs & Stratton call 800-743-4115, between

8:00 AM and 5:00 PM CT.

Installation Inspection

Before placing the system into service, inspect the entire

installation carefully.

Complete the ”Installation Checklist” supplied with the

generator as you make the inspection. Ensure all items have

been filled-in and all signatures have been obtained. Instruct

the owner to mail the white copy to the address shown on

the checklist.

WARNING Transfer switch contains hazardous voltage

that could cause electrocution resulting in death

or serious injury.

• Despite the safe design of the transfer switch, operating

this equipment imprudently, neglecting its maintenance or

being careless could cause possible injury or death.

• DO NOT work on equipment without removing 15 amp

fuse in generator and placing generator switch in

OFF position.

• To reduce risk of electrical shock or personal injury,

disconnect all sources of supply voltage before servicing.

13

Troubleshooting

Problem Cause Correction

Au tomatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

3. Generator disconnect circuit breaker

open in transfer switch.

1. Reset generator circuit breaker.

2. Refer to generator manual.

3. Reset generator disconnect circuit

breaker in transfer switch.

Au tomatic transfer switch does not

transfer to utility

1. Utility disconnect circuit breaker

open in transfer switch.

2. Utility voltage not acceptable.

1. Reset utility disconnect circuit

breaker in transfer switch.

2. Wait for utility voltage to return

to normal.

Ge nerator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Ge nerator or supervised loads (air

conditioner, etc.) are operating

improperly when generator is

supplying power

1. A-A or B-B contacts not

operating correctly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for

proper operation and/or check

control wiring to external load.

2. Decrease load to generator.

3. Plug CT connectors into

control module.

4. Contact local authorized

service center.

Ge nerator is still running after utility

power is restored

1. Minimum engine run time has

not elapsed.

2. Fuse(s) in transfer switch

is defective.

1. Wait five minutes for transfer switch

to retransfer to utility power.

2. Check fuse(s) and replace

if necessary.

14 BRIGGSandSTRATTON.COM

Schematic Diagram, 071038

15

Wiring Diagram, 071038

16 BRIGGSandSTRATTON.COM

Schematic Diagram, 071055

A

B

J1

J2

J3

J4

J6

J5

CT1

CT2

127

205

N1

556

N2

128

206

E1

E2

N2

CONTROL BOARD

TRANSFER

SWITCH

FUSE

HOLDER

UTILITY

240 VAC

FROM MAIN DISTRIBUTION PANEL

FROM GENERATOR

J3 J2 J1 J4 J6 J5

CONTROL BOARD

AABB

CT2

CT1

E2

T2

T1

E1

N2

N1

NC

NO

F1

F2

556

N2

N1

205 206

E2

E1

NC

NO

128

127

N1

E1

TRANSFER SWITCH

UTILITY SUPPLY

240VAC

TO GENERATOR

UTILITY

240 VAC

2 AMP

FUSE

GENERATOR SUPP

LY

240 VAC

ESSENTIAL BRANCH

CIRCUIT BREAKER BUS

N

E

Dashed lines show customer (field) connections

17

Wiring Diagram, 071055

A

B

J1

J2

J3

J4

J6

J5

CT1

CT2

127

205

N1

556

N2

128

206

E1

E2

N2

CONTROL BOARD

TRANSFER

SWITCH

FUSE

HOLDER

UTILITY

240 VAC

FROM MAIN DISTRIBUTION PANEL

FROM GENERATOR

J3 J2 J1 J4 J6 J5

CONTROL BOARD

AABB

CT2

CT1

E2

T2

T1

E1

N2

N1

NC

NO

F1

F2

556

N2

N1

205 206

E2

E1

NC

NO

128

127

N1

E1

TRANSFER SWITCH

UTILITY SUPPLY

240VAC

TO GENERATOR

UTILITY

240 VAC

2 AMP

FUSE

GENERATOR SUPPLY

240 VAC

ESSENTIAL BRANCH

CIRCUIT BREAKER BUS

N

E

18 BRIGGSandSTRATTON.COM

Product Specifications

Model 071038

Rated Maximum Load Current*

(at 25°C/77°F) ....................................................... 200 Amps

Rated AC Voltage ................................................... 250 Volts

Poles .................................................................................... 2

Frequency .....................................................................60 Hz

Fault Current Rating ...... 25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals ................................................... 24 Volt AC

B-B Terminals ....................1 Amp, 125 Volt AC, Pilot Duty

Normal Operating Range .....-20°F (-28.8°C) to 104°F (40°C)

Weight .............................................................40 lbs. (18 kg)

* This transfer switch is certified in accordance with UL (Underwriters

Laboratories) 1008 (transfer switch equipment).

Model 071055

Rated Maximum Load Current*

(at 25°C/77°F) ....................................................... 100 Amps

Rated AC Voltage ................................................... 250 Volts

Poles .................................................................................... 2

Frequency .....................................................................60 Hz

Fault Current Rating ...... 25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals ................................................... 24 Volt AC

B-B Terminals ....................1 Amp, 125 Volt AC, Pilot Duty

Normal Operating Range .....-20°F (-28.8°C) to 104°F (40°C)

Weight .............................................................25 lbs (11 kg).

* This transfer switch is certified in accordance with UL (Underwriters

Laboratories) 1008 (transfer switch equipment).

Automatic Transfer Switch

100/200 Amperios

Interruptor de

transferencia automática

con módulo de control de energía eléctrica de CA™

Manual de instalación y del operario

Preguntas?

La ayuda es justa un momento lejos!

Llamada: Línea Directa de generador de hogar

800-743-4115 M-F 8-5 CT

2 BRIGGSandSTRATTON.COM

Gracias por comprar este conectador automático de Briggs & Stratton® Power Products. Este producto está diseñado para

utilizarse con generadores de reserva domésticos específicos y puede no funcionar con generadores producidos por otros

fabricantes. Recurra a un electricista profesional cualificado para determinar la aplicabilidad de este equipo en generadores

fabricados por terceros. Si se utiliza y mantiene de acuerdo con las instrucciones de este manual, su sistema le proporcionará

muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de este sistema y

cómo evitarlos. Se ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Debido a que

cada instalación es única, es imposible conocer y recomendar todos los procedimientos y métodos posibles para efectuarla.

No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento existente. Es importante que lea y

comprenda perfectamente estas instrucciones antes de intentar instalar o utilizar este equipo. Guarde estas instrucciones

para futuras consultas.

Este el conectador requiere instalación profesional antes de utilizarse. Consulte las instrucciones sobre los

procedimientos de instalación en la sección Instalación del presente manual. Los conectador sólo deben ser instalados por

electricistas con licencia. Las instalaciones deben cumplir estrictamente la totalidad de los códigos, estándares y regulaciones

federales, estatales y locales vigentes. El instalador debe seguir las instrucciones detalladamente.

Ubicación

Nunca debe ir demasiado lejos para encontrar el soporte y servicio de Briggs & Stratton para su sistema. Consulte las

Páginas Amarillas. Existen múltiples distribuidores de servicio autorizados que ofrecen un servicio de calidad. También

puede comunicarse con el Servicio técnico por teléfono al 800-743 4115 entre 08:00 a. m. y 5:00 p. m., hora del centro

de los EE. UU; o haga clic en Buscar un distribuidor en BRIGGSandSTRATTON.COM para que aparezca una lista de

distribuidores autorizados.

Para futuras consultas

Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan

problemas relacionados con la compra en el futuro.

Número de modelo _______________________________

Revisión _________

Número de serie _______________________________

Fecha de compra _______ / _________ / ____________

La page est en cours de chargement...

Simplicity 071038-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 071038-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents