Simplicity 020795-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020795-00

Catégorie: Pulvérisateur de peinture

Taper: Manuel utilisateur

Manual No. 80097854 Rev. A

Pressure Washer

Operator’s Manual

Model Number _____________________________

Revision __________________________________

Serial Number ______________________________

Date Purchased ____________________________

Husqvarna® is a registered trademark of Husqvarna AB.

Used under license.

(877) 224-0458

www.husqvarna.com/us

2 www.husqvarna.com/us

Table of Contents

Symbols and Meanings ...........................2

Equipment Description............................3

Features and Controls ............................4

Operation.......................................6

Maintenance ...................................12

Storage .......................................15

Troubleshooting ................................16

Warranty ......................................18

To ensure prompt and complete warranty coverage, register

your product online at www.onlineproductregistration.com.

Symbols and Meanings

Signal Meaning

DANGER

Indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING

Indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazard which, if not avoided,

could result in minor or moderate injury.

NOTICE

Indicates information considered

important, but not hazard-related.

Symbol Name Explanation

Safety Alert

Symbol

Indicates a potential personal

injury hazard.

Read

Operator’s

Manual

Failure to follow warnings,

instructions and operator’s

manual could result in death or

serious injury.

Toxic

Fumes

Engine exhaust contains carbon

monoxide, a poisonous gas that

could kill you in minutes. You

cannot smell it or see it.

Fire

Fuel and its vapors are

extremely ammable which

could cause burns or re

resulting in death or serious

injury.

Engine exhaust could cause

re resulting in death or serious

injury.

Symbol Name Explanation

Fluid

Injection

High-pressure water could cut

through skin resulting in serious

injury and possible amputation.

Spray,

Flying

Objects

Risk of eye injury. Spray could

splash back or propel objects

resulting in serious injury.

Hot Surface

Contact with muer area could

cause burns resulting in serious

injury.

Electric

Shock

Contact with power source

could cause electrical shock

resulting in death or serious

injury.

Kickback

Recoil starter kickback will pull

hand and arm toward engine

faster than you can let go which

could cause broken bones,

sprains or bruises resulting in

serious injury.

Chemical

Burn

Chemicals could cause burns

resulting in death or serious

injury.

Slippery

Surface/Fall

Slippery wet surfaces could

cause you to fall resulting in

death or serious injury.

Fall

Kickback from spray gun could

cause you to fall resulting in

death or serious injury.

WARNING! This product can expose you to

chemicals including gasoline engine exhaust,

which is known to the State of California to cause

cancer, and carbon monoxide, which is known to the State of

California to cause birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

WARNING! This product contains lead and lead

compounds, known to the state of California to

cause birth defects or other reproductive harm.

Wash your hands after handling this product. Cancer and

Reproductive Harm - www.P65Warnings.ca.gov.

High Pressure Hose — Connect one end to water pump

and the other end to spray gun.

High Pressure Outlet — Connection for high pressure

hose.

Identication Label — Provides model and serial number of

pressure washer.

Pump — Ceramic coated stainless steel plungers, triplex

pump that develops high pressure.

Water Inlet — Connection for garden hose.

Equipment Description

Read this manual carefully and become familiar

with your product. Know its applications, its

limitations, and any hazards involved. Save these

original instructions for future reference.

To aid in outdoor cleaning projects, this engine-driven,

high-pressure cleaning machine uses a variety of spray

tips and detergent.

Know how to stop the product and reduce pressure

quickly. Keep operating area clear and do not allow

children to operate pressure washer.

Stay alert—watch what you are doing. Do not operate

pressure washer when fatigued or under the inuence of

alcohol or drugs.

Every eort has been made to ensure that information in

this manual is accurate and current. However, we reserve

the right to change, alter, or otherwise improve the product

and this document at any time without prior notice.

NOTICE If you have questions about intended use,

contact an authorized service dealer. This equipment is

designed to be used with Briggs & Stratton

authorized

parts only.

For engine related questions, call American Honda

Motor Company, Inc. at (800) 426-7701 or visit

www.honda-engines.com for a dealer locator.

This spark ignition system complies with the Canadian

Standard CAN ICES-2/NMB-2.

High Pressure Outlet

Water Inlet

High Pressure Hose

Pump

Identication Label

4 www.husqvarna.com/us

Features and Controls

Compare the illustrations with your pressure washer to familiarize yourself with the locations of various controls and

product warnings.

Automatic Cool Down System — Prevents internal pump

damage by discharging warm water to the ground.

Detergent Siphon Tube — Use to siphon pressure washer

safe detergent into the low pressure stream.

Pressure Control Knob — Varies pressure of high pressure

spray.

Spray Gun — Controls spray using trigger. Includes trigger

lock.

Spray Tips — Multiple patterns for various cleaning

applications.

Spray Wand — Allows you to switch between spray tips.

Turbo Spray Tip — Whirls a powerful pin-point jet of water

for intense cleaning.

Spray Tips

Spray Wand

Spray Gun

Automatic Cool Down

System (on pump)

Detergent Siphon Tube

Pressure Control Knob

Turbo Spray Tip

6 www.husqvarna.com/us

Operation

Step 1: Safe Location

Before starting the pressure washer, there are two equally

important safety concerns regarding carbon monoxide

poisoning and re that must be addressed.

Operation Location to Reduce the Risk of Carbon

Monoxide Poisoning

The engine exhaust of all fossil fuel burning equipment,

such as a pressure washer, contains carbon monoxide, a

poisonous gas that could kill you in minutes. You cannot

smell it, see it, or taste it. Even if you do not smell exhaust

fumes, you could still be exposed to carbon monoxide gas.

By law, it is required in many states to have a carbon

monoxide alarm in operating condition in your home. A

carbon monoxide alarm is an electronic device that detects

hazardous levels of carbon monoxide. When there is

a buildup of carbon monoxide, the alarm will alert the

occupants by ashing a visual indicator light and an alarm.

Smoke alarms cannot detect carbon monoxide gas.

WARNING! Engine exhaust contains carbon

monoxide, a poisonous gas that could kill you in

minutes. You cannot smell it, see it, or taste it.

Even if you do not smell exhaust fumes, you could still be

exposed to carbon monoxide gas.

• Operate this product only outdoors, far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas accumulating and the potential of being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• Do not run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors and

windows for ventilation. Carbon monoxide can quickly

build up in these spaces and can linger for hours, even

after this product has shut o.

• Point exhaust away from all homes and occupied

spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air right away. See a doctor. You may

have carbon monoxide poisoning.

Carbon monoxide alarm

Operation Location to Reduce the Risk of Fire

WARNING! Exhaust heat/gases could ignite

combustibles, structures or damage fuel tank

causing a re, resulting in death or serious injury.

• Pressure washer must be at least 5 ft. (1.5 m) from any

structure, overhang, trees, windows, doors, and any wall

opening, shrubs, or vegetation over 12 in. (30.5 cm) in

height.

• Do not place pressure washer under a deck or other type

of structure that may conne airow. Smoke alarm(s)

must be installed and maintained indoors according to

the manufacturer’s instructions /recommendations.

• Carbon monoxide alarms cannot detect smoke.

• It is a violation of California Public Resource Code

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

dened in Section 4442, maintained in eective working

order. Other states or federal jurisdictions may have

similar laws, reference Federal Regulation 36 CFR Part

261.52.

• Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

Step 2: Oil and Fuel

Check Oil Level

1. Make sure pressure washer is on a level surface.

2. Refer to engine operator’s manual and follow oil and

fuel recommendations and instructions.

Transporting

Do not tip engine or equipment at an angle which causes

fuel to spill.

Step 3: Set Up

Clean Debris

Clean any accumulated debris. Keep area around muer

free from any debris.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a damp cloth to wipe exterior surfaces clean.

Lubricate O-rings

Lubricate all connections shown to extend the life of the

o-rings.

1. Inspect and clean connecting surfaces prior to

lubrication and assembly. Replace o-rings that are

damaged or missing. See Common Service Parts.

NOTICE Never repair leaking connections with sealant of

any kind. Replace o-ring.

2. Use a small brush or cotton swab to apply a light

coating of grease directly to o-rings.

MUFFLER

5 ft (1.5 m)

min.

5 ft (1.5 m) min.

Spray Gun

High Pressure Hose

Spray Wand

High Pressure Outlet

8 www.husqvarna.com/us

Check / Connect Gun and Hose

1. If spray gun trigger depresses without pressing

trigger lock or if spray gun remains depressed when

released, replace spray gun immediately.

2. If high pressure hose is damaged, exposing inner

mesh, replace immediately.

3. Pull high pressure hose quick connect collar back,

slide onto spray gun and release. Tug on hose to

ensure it is secure.

4. Pull high pressure outlet quick connect collar back,

insert high pressure hose and release. Tug on hose to

ensure it is secure.

WARNING! The high pressure uid could cut

through skin and its underlying tissues, resulting

in serious injury and possible amputation. Never

attach spray wand directly to high pressure hose.

Check Water Inlet Screen / Connect Garden Hose

1. Inspect inlet screen. Remove debris or replace if

damaged.

2. Run water through garden hose (not to exceed 50 ft

(15 m) to clean out debris, then connect to water inlet.

NOTICE There must be at least 10 ft (3 m) of

unrestricted garden hose between the pressure washer

inlet and any device, such as a vacuum breaker, to

prevent pump damage.

3. Turn on water, point spray gun in safe direction, press

trigger lock and depress trigger to purge pump system

of air.

4. Attach spray wand to spray gun. Tighten by hand.

Step 4: Spray Tips

1. Select desired spray tip:

Low Pressure

Black Soap

Use to apply

detergent

Delicate Rinse

White, 40°

Green, 25°

Cars / Vans

/ Trucks /

Outdoor

Furniture

General Rinse

Yellow, 15°

Siding /

Patios Decks

Driveways /

Garage Floors

Maximum

Rinse

Red, 0°

Paint Removal

/ Oil Stains

/ Rust Removal

Intense

Cleaning

Turbo, 0°

2. Pull spray wand quick connect collar back, insert

spray tip and release. Tug spray tip to ensure it is

secure.

Trigger Lock

Inlet Screen

Step 5: Start Up

NOTICE Do not start engine without water supply

connected and turned on.

1. Level product before starting.

WARNING! Risk of eye injury. Spray could

splash back or propel objects, resulting in

serious injury.

• Always wear indirect vented (chemical splash) safety

goggles when using or near this product. (Safety glasses

do not provide full protection).

• Always wear protective clothing such as long-sleeved

shirts, long pants and closed-toed shoes.

WARNING! Recoil starter kickback (rapid

retraction) will pull hand and arm toward engine

faster than you can let go, which could cause

broken bones, fractures, bruises, or sprains and result in

serious injury.

2. Position yourself as shown below, and start engine

according to instructions given in engine operator’s

manual.

WARNING! High-pressure water could cut

through skin resulting in serious injury and

possible amputation.

• Do not direct discharge at self or others.

• Call physician immediately if cut by uid. Do not treat as

a simple cut.

• Do not touch spray tips while spraying.

WARNING! Use of pressure washer

could create slippery surfaces causing

you to fall, resulting in death or serious

injury. Kickback from spray gun could cause you to fall

resulting in death or serious injury. Operate pressure

washer from a stable surface.

3. Firmly grasp spray gun with both hands, point spray

gun in safe direction, press trigger lock and depress

trigger to begin spraying.

4. Apply high pressure spray to a small area rst, then

check the surface for damage. If no damage is found,

it is okay to continue cleaning.

5. Increase (decrease) spray pressure by turning

pressure control knob clockwise (counterclockwise).

Use lower pressure to wash items such as a car or

boat. Use higher pressure to strip paint and degrease

driveways.

WARNING! Risk of electrocution. Contact with

power source could cause electric shock or burn

resulting in death or serious injury. Never spray

near power source.

Usage Tips

• For most eective cleaning, keep spray tip 8 to 24 in (20

to 61 cm) away from cleaning surface.

• Do not use high pressure spray tips closer than 6 in (15

cm) to prevent damage to the cleaning surface.

• Start at the top of the area to be rinsed, working down

with long, even, overlapping strokes.

Pressure

Control Knob

10 www.husqvarna.com/us

Step 6: Applying Detergent

WARNING! Chemicals could cause burns

resulting in death or serious injury.

• Follow chemical manufacturer’s label instructions for

proper use and handling of the chemical.

• Only use products marketed for use with pressure

washers.

• Never spray acids or ammable liquids.

Check Detergent Siphoning Tube

Clean detergent tube if clogged or replace if leaking.

To apply detergent, follow these steps:

1. Attach detergent siphon tube to the barbed fitting on

the pump.

2. Prepare detergent per pressure washer detergent

manufacturer’s instructions.

3. Insert detergent siphon tube into pressure washer

detergent.

4. Install black detergent spray tip. See Spray Tips.

5. Apply per manufacturer’s instructions.

NOTICE Detergent cannot be applied with the high

pressure spray tips (White, Green, Yellow, Red or Turbo).

Step 7: Shut Down

1. Release spray gun trigger and let engine idle for one

minute.

2. Turn engine o according to instructions given in

engine operator’s manual.

WARNING! Spray gun traps high water

pressure, even after engine shut down and water

disconnection, which could result in serious

injury.

3. Point spray gun in safe direction. Press trigger lock

and depress trigger to relieve high water pressure.

Step 8: Clean Up

1. Turn o water and purge system.

2. Disconnect and drain all hoses, spray gun and spray

wand.

3. Empty pump of all liquids by pulling recoil handle

about six times.

NOTICE If storing in freezing temperatures or more than

30 days, see Storage.

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

rst. See the engine operator’s manual for instructions on

how to properly maintain the engine.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the pressure washer. See any authorized

dealer for service.

Pump Oil Maintenance

1. Clean around oil drain plug at bottom of pump,

remove plug and drain oil completely.

2. Reinstall oil drain plug and tighten rmly.

3. Clean area around pump oil dipstick and remove

dipstick. Fill pump with SAE 30 weight oil

(approximately 10 oz. (0.3 liters)) to the point of

overowing.

4. Install pump oil dipstick and wipe up any spilled oil.

Detergent Siphoning Check Ball

The check ball in detergent siphoning system may become

stuck from dried soap or minerals in water. The check ball

can be freed by performing the following:

WARNING! Chemical Burn Hazard. Chemicals

could cause burns resulting in death or serious

injury. Follow chemical manufacturer’s label

instructions for proper use and handling of the chemical.

Following Shut Down, remove detergent siphoning hose

from barbed tting on pump.

1. Insert paper clip, or similar device, into barbed tting

on pump and push down until ball moves.

2. Reinstall detergent siphoning hose.

Spray Tip Maintenance

Clean an obstructed spray tip to correct a pulsing

sensation when squeezing the spray gun trigger.

1. Following Shut Down, remove spray tip from spray

wand.

2. Use a paper clip, or similar device, to free foreign

material.

Engine Maintenance

See the engine operator’s manual for instructions on how

to properly maintain the engine.

Common Service Parts

Pump Saver™ ............................6039

O-ring Maintenance Kit ...................705001

Water Inlet Screen ..................... B2384GS

Engine Oil Bottle ...............100005 or 100028

Contact an authorized service dealer or

BRIGGSandSTRATTON.com for a full list of parts and

diagrams.

Every 8 Hours or Daily (see Operation Section)

Check engine oil level

Clean debris

Lubricate o-rings

Check spray gun

Check high pressure hose

Check / clean water inlet screen

Check detergent siphoning tube

Every 50 Hours

Change pump oil

Pump Oil Drain

12 www.husqvarna.com/us

Storage

WARNING! Fuel and its vapors are extremely

ammable, which could cause burns or re,

resulting in death or serious injury. Do not store

fuel near ignition source.

1. Place detergent siphon tube in water and ush

detergent from system by running pressure washer

with black spray tip.

Protecting Fuel System

2. Treat or drain fuel from pressure washer as fuel can

become stale when stored over 30 days.

Each time you ll the container with fuel, add STA-BIL

360°® PROTECTION™ to the fuel as specied by the

manufacturer’s instructions. This keeps fuel fresh and

decreases fuel-related problems or contamination in the

fuel system.

It is not necessary to drain fuel from the engine when STA-

BIL 360°® PROTECTION™ is added as instructed. Before

storage, turn the engine ON for 2 minutes to move the fuel

and stabilizer through the fuel system.

If fuel in the engine has not been treated with STA-

BIL 360°® PROTECTION™, it must be drained into an

approved container. Then run the engine until it stops from

lack of fuel.

Engine Maintenance

See the engine operator’s manual for instructions on how

to properly maintain the engine.

Protecting the Pressure Washer

3. Turn o water and purge system.

4. Disconnect and drain all hoses, spray gun and spray

wand.

5. Empty pump of all liquids by pulling recoil handle

about six times.

NOTICE Store spray gun indoors and keep from freezing.

Protecting the Pump

6. Treat pump with Pump Saver.

Use Pump Saver to protect pump from damage caused by

mineral deposits and freezing. It also lubricates pistons and

seals. See Common Service Parts.

Read and follow all Pump Saver warnings and instructions.

If Pump Saver is not available, connect a 3 ft. (1 m)

section of garden hose to water inlet. Pour RV-antifreeze

(antifreeze without alcohol) into hose. Pull recoil handle

twice. Disconnect hose.

NOTICE You must protect your product from freezing

temperatures. Failure to do so will permanently damage

your pump and spray gun rendering your product

inoperable.

7. Store unit in a clean and dry area.

WARNING! Storage covers could cause a re

resulting in death or serious injury. Do not place

a storage cover over a hot pressure washer. Let

product cool before installing cover.

Troubleshooting

Problem Cause Correction

Pump has following

problems: failure to

produce pressure, loss

of pressure, low water

volume.

1. Low pressure spray tip installed.

2. Pressure control knob is turned to low

spray pressure setting.

3. Inadequate water supply.

4. Clogged inlet hose screen.

5. Spray tip is obstructed.

6. Connections leak.

7. High pressure hose or spray gun leaks.

1. Replace with high pressure spray tip.

2. Turn pressure control knob clockwise to

increase spray pressure.

3. Provide adequate water ow.

4. Check and clean inlet hose screen.

5. Clean spray tip. See Spray Tip

Maintenance.

6. Tighten connections or replace o-rings.

7. Replace.

Detergent fails to mix

with spray.

1. High pressure spray tip installed.

2. Check ball stuck in detergent

siphoning system.

3. Detergent siphoning tube is clogged or

cracked.

1. Replace with low pressure black spray tip.

2. Free check ball. See Detergent Siphoning

Check Ball.

3. Clean or replace detergent siphoning

tube.

Engine will not start;

starts and runs rough

or shuts down during

operation.

1. Out of fuel.

2. Flooded with fuel.

3. Dirty air lter.

4. Spark plug wire not connected to spark

plug.

1. Fill fuel tank.

2. Wait 5 minutes before starting.

3. Clean or replace air lter.

4. Connect wire to spark plug.

For all other issues, see an authorized dealer.

*This pressure washer is rated in accordance to the Pressure Washer Manufacturers’ Association (PWMA) standard PW101-2010

(Testing and Rating Performance of Pressure Washers).

Specications

Pressure and Flow ............................4000 PSI (276 bar) @ 4.0 GPM (15.1 L/min)*

Water Supply Temperature .....................................41°F (5°C) - 100°F (38°C)

min Water Supply Flow Rate ...................................... 5.0 GPM (18.9 L/min)

min Water Supply Pressure ...........................................20 PSI (1.38 bar)

Pump Oil Capacity ................................................... 10 oz (0.3 Liters)

14 www.husqvarna.com/us

80081746_EN Rev -

HUSQVARNA WARRANTY POLICY

LIMITED WARRANTY

Husqvarna® is a registered trademark of Husqvarna AB and is used under license to Briggs & Stratton Corporation. Briggs & Stratton warrants that, during the

warranty period specied below, it will repair or replace, free of charge, any part that is defective in material or workmanship or both. Transportation charges on

product submitted for repair or replacement under this warranty must be borne by purchaser. This warranty is eective for and is subject to the time periods and

conditions stated below. For warranty service, nd the nearest Authorized Service Dealer in our dealer locator map at BRIGGSANDSTRATTON.COM. The purchaser

must contact the Authorized Service Dealer, and then make the product available to the Authorized Service Dealer for inspection and testing.

There is no other express warranty. Implied warranties, including those of merchantability and tness for a particular purpose, are limited to the

warranty period listed below, or to the extent permitted by law. Liability for incidental or consequential damages are excluded to the extent exclusion

is permitted by law. Some states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specic legal rights and you

may also have other rights which vary from state to state or country to country.**

WARRANTY PERIOD

* Applies to Briggs & Stratton engines only. Warranty coverage of non-Briggs & Stratton engines is provided by that engine manufacturer. Emissions-related components

are covered by the Emissions Warranty Statement.

** In Australia - Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be

of acceptable quality and the failure does not amount to a major failure. For warranty service, nd the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing to [email protected], Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the rst retail or commercial consumer. “Consumer use” means personal residential household use by a retail

consumer. “Commercial use” means all other uses, including use for commercial, income producing or rental purposes. Once a product has experienced commercial

use, it shall thereafter be considered as a commercial use product for purposes of this warranty.

Save your proof of purchase receipt. If you do not provide proof of the initial purchase date at the time warranty service is requested, the manufacturing date of the

product will be used to determine the warranty period. Product registration is not required to obtain warranty service on Briggs & Stratton products.

ABOUT YOUR WARRANTY

Warranty service is available only through Briggs & Stratton Authorized Service Dealers. This warranty covers only defects in materials or workmanship. It does not cover

damage caused by improper use or abuse, improper maintenance or repair, normal wear and tear, or stale or unapproved fuel.

Improper Use and Abuse - The proper, intended use of this product is described in the Operator’s Manual. Using the product in a way not described in the Operator’s

Manual or using the product after it has been damaged will not be covered under this warranty. Warranty coverage will also not be provided if the serial number on the

product has been removed or the product has been altered or modied in any way, or if the product has evidence of abuse such as impact damage or water/chemical

corrosion damage.

Improper Maintenance or Repair - This product must be maintained according to the procedures and schedules provided in the Operator’s Manual, and serviced or

repaired using genuine Briggs & Stratton parts or equivalent. Damage caused by lack of maintenance or use of non-original parts is not covered by warranty.

Normal Wear and Tear - Like most mechanical devices, your unit is subject to wear even when properly maintained. This warranty does not cover repairs when normal

use has exhausted the life of a part or the equipment. Maintenance and wear items such as lters, belts, cutting blades, and brake pads (except engine brake pads) are

not covered by warranty due to wear characteristics alone, unless the cause is due to defects in material or workmanship.

Stale or Unapproved Fuel - In order to function correctly, this product requires fresh fuel that conforms to the criteria specied in the Operator’s Manual. Engine or

equipment damage caused by stale fuel or the use of unapproved fuels (such as E15 or E85 ethanol blends) is not covered by warranty.

Other Exclusions - This warranty excludes damage due to accident, abuse, modications, alterations, improper servicing, freezing or chemical deterioration.

Attachments or accessories that were not originally packaged with the product are also excluded. There is no warranty coverage on equipment used for primary power in

place of utility power or on equipment used in life support applications. This warranty does not include used, reconditioned, second-hand, or demonstration equipment or

engines. This warranty also excludes failures due to acts of God and other force majeure events beyond the manufacturer’s control.

Item Consumer Use Commercial Use

Equipment 24 months 3 months

Engine* 24 months 3 months

Frame 36 months 3 months

Limpiadora a presión

Manual del operador

Número de modelo __________________________

Revisión __________________________________

Número de serie ____________________________

Fecha de compra ___________________________

Milwaukee, WI, USA. Reservados todos los derechos.

Husqvarna® es una marca registrada de Husqvarna AB.

Usa abajo licencia.

(877) 224-0458

www.husqvarna.com/us

2 www.husqvarna.com/us

Índice de contenidos

Símbolos y sus signicados........................2

Descripción del equipo............................3

Características y controles.........................4

Operación ......................................6

Mantenimiento .................................12

Almacenamiento................................15

Solución de problemas...........................16

Garantía.......................................18

Registrar su producto

Para asegurar pronta y completa cobertura de

la garantía, registre su producto en línea en

www.onlineproductregistration.com.

Símbolos y sus signicados

Señal Signicado

PELIGRO

Indica un riesgo que, si no se evita,

ocasionará la muerte o lesiones

graves.

ADVERTENCIA

Indica un riesgo que, si no se evita,

podría ocasionar la muerte o lesiones

graves.

ATENCIÓN

Indica un riesgo que, si no se evita,

podría ocasionar lesiones menores o

moderadas.

AVISO

Indica una información que se considera

importante pero que no está relacionada

con un peligro potencial.

Símbolo Nombre Explicación

Símbolo de

alerta de

seguridad

Indica un posible riesgo para su

integridad física.

Lea el

Manual del

operador

La omisión de las advertencias,

las instrucciones y el manual

del operador podría redundar

en lesiones graves o incluso la

muerte.

Gases

tóxicos

La descarga de escape del

motor contiene monóxido de

carbono, un gas tóxico que

puede matar en minutos. No

puede olerse ni verse.

Incendio

El combustible y sus vapores

son extremadamente

inamables, lo que podría

causar quemaduras o incendios

que resulten en lesiones graves

o la muerte.

El escape del motor puede

causar un incendio y ocasionar

lesiones graves o la muerte.

Símbolo Nombre Explicación

Inyección

de uido

La alta presión de agua puede

cortar la piel y causar heridas

graves y posible amputación.

Spray,

objetos

que salen

volando

Riesgo de lesión ocular. El

agua rociada podría salpicar o

expulsar objetos, lo que puede

provocar lesiones graves.

Supercie

caliente

El contacto con el área

del moe podría provocar

quemaduras y causar lesiones

graves.

Descarga

eléctrica

El contacto con los cables

eléctricos podría provocar

choque eléctrico y ocasionar

lesiones graves o la muerte.

Retroceso

El contragolpe del cable del

arrancador retráctil jalará la

mano y el brazo hacia el motor

más rápido de lo que usted

pueda soltarlo, lo que puede

causar huesos rotos, esguinces

o hematomas que resulten en

lesiones graves.

Quemadura

química

Los productos químicos

podrían causar quemaduras

que resulten en la muerte o en

lesiones graves.

Supercie

resbaladiza/

Caída

Supercies resbaladizas

mojadas podrían provocar

caídas que resulten en la

muerte o en lesiones graves.

Caída

El retroceso de la pistola puede

hacerle caer, lo que puede

ocasionarle la muerte o una

lesión grave.

¡ADVERTENCIA! Este producto puede

exponerlo a sustancias químicas, entre las que

se incluyen emisiones de escape de motor de

gasolina, reconocidas por el Estado de California como

causantes de cáncer, y monóxido de carbono, reconocido

por el Estado de California como causante de defectos de

nacimiento u otros problemas reproductivos. Para obtener

más información, visite www.P65Warnings.ca.gov.

¡ADVERTENCIA! Este producto contiene plomo

y compuestos de plomo que, de acuerdo al

estado de California, pueden causar defectos de

nacimiento u otros problemas reproductivos. Lávese las

manos después de manipular este producto. Cáncer y

Problemas Reproductivos – www.P65Warnings.ca.gov

Descripción del equipo

Lea este manual cuidadosamente y familiarícese

con el producto. Conozca sus aplicaciones, sus

limitaciones y cualquier riesgo implicado. Conserve

estas instrucciones originales para futuras consultas.

Para facilitar los proyectos de limpieza para exteriores, esta

máquina limpiadora a alta presión impulsada por motor

utiliza una variedad de boquillas rociadoras y detergente.

Sepa cómo detener el producto y disminuir la presión

rápidamente. Mantenga el área de operación libre y no

permita que niños operen la lavadora a presión.

Manténgase alerta, observe lo que está haciendo. No haga

funcionar la lavadora a presión si está cansado o bajo la

inuencia de alcohol o drogas.

Se ha hecho todo lo posible para garantizar que la

información contenida en este manual sea precisa y actual.

Sin embargo, nos reservamos el derecho de realizar

cambios, alterar o mejorar el producto y este documento, en

cualquier momento sin previo aviso.

AVISO Si tiene alguna pregunta acerca del uso previsto,

póngase en contacto con el distribuidor autorizado. Este

equipo se ha diseñado para usarse con partes autorizadas

de Briggs & Stratton

únicamente.

Para toda pregunta relativa a la motor, llame a

American Honda Motor Company al (800) 426-7701

o visite www.honda-engines.com para localizar un

concesionario.

Este sistema de encendido por chispa cumple con la

norma canadiense CAN ICES-2/NMB-2.

Bomba — desatascadores de acero inoxidable con

revestimiento cerámico, bomba triplex que desarrolla la

alta presión.

Entrada de agua — conexión para la manguera de jardín.

Etiqueta de identicación — proporciona el modelo y

número de serie de la lavadora a presión.

Manguera para alta presión — conecte un extremo de la

manguera a la bomba de agua y el otro a la pistola rociadora.

Toma de alta presión — conexión para la manguera de

alta presión.

Entrada de agua

Etiqueta de identicación

Manguera para alta presión

Bomba

Toma de alta presión

4 www.husqvarna.com/us

Características y controles

Compare las ilustraciones con su lavadora a presión para familiarizarse con la ubicación de los diversos controles y

advertencias del producto.

Boquillas rociadoras — múltiples patrones para diversas

aplicaciones de limpieza.

Manguera del sifón para detergente — usado para

succionar detergente de la botella de químicos a la

corriente de agua de baja presión.

Perilla de control de la presión — varía la presión de

rociado de la presión.

Pistola rociadora — controla el spray mediante el gatillo.

Incluye bloqueo del gatillo.

Sistema de enfriamiento automático — evita daños a la

bomba interna mediante la descarga de agua tibia al suelo.

Vara rociadora — permite intercambiar los boquillas

rociadoras.

Boquilla rociadora turbo — hace girar un poderoso chorro

de agua de precisión para una limpieza profunda.

Boquillas rociadoras

Vara rociadora

Pistola rociadora

Sistema de enfriamiento

automático (en la bomba)

Manguera del sifón

para detergente

Perilla de control

de la presión

Boquilla

rociadora turbo

6 www.husqvarna.com/us

Operación

Paso 1: Ubicación segura

Antes de arrancar la lavadora a presión, hay dos

problemas de seguridad igualmente importantes con

respecto a la intoxicación por monóxido de carbono e

incendios que deben abordarse.

Ubicación durante el funcionamiento para reducir el

riesgo de intoxicación por monóxido de carbono

El escape del motor de todos los equipos que queman

combustibles fósiles, como la lavadora a presión, contiene

monóxido de carbono, un gas tóxico que puede ser mortal

en minutos. Además de que no se lo puede ver, es inodoro

e insípido. Incluso si no huele los gases del escape, puede

estar expuesto al monóxido de carbono.

En muchos estados, la ley requiere el uso de alarmas de

monóxido de carbono funcionales en los hogares. Se

trata de un dispositivo electrónico que detecta niveles

peligrosos de monóxido de carbono. Cuando se produce

una acumulación de monóxido de carbono, la alarma avisa

a los habitantes con un sonido y una luz indicadora, visible

e intermitente. Las alarmas de humo no pueden detectar el

monóxido de carbono.

¡ADVERTENCIA! La descarga de escape del

motor contiene monóxido de carbono, un gas

tóxico que puede matar en minutos. Además de

que no se lo puede ver, es inodoro e insípido. Incluso si no

huele los gases del escape, puede estar expuesto al

monóxido de carbono.

• Opere este producto solamente en exteriores, lejos de

ventanas, puertas y ventilaciones para reducir el riesgo

de que el monóxido de carbono se acumule y pueda

circular en espacios habitados.

• Instale alarmas de monóxido de carbono con baterías

o enchufe con batería de respaldo siguiendo las

instrucciones del fabricante. Las alarmas de humo no

pueden detectar el monóxido de carbono.

• No opere este producto dentro de hogares, garajes,

sótanos, espacios reducidos, cobertizos u otros

espacios parcialmente cerrados, incluso si usa

ventiladores o deja las puertas y ventanas abiertas. El

monóxido de carbono se puede acumular rápidamente

en estos espacios y puede permanecer durante horas,

incluso después de que se apaga este producto.

• Apunte el escape en la dirección opuesta de las casas y

de los espacios donde haya personas u objectos.

Si comienza a sentirse mareado o débil cuando utiliza el

producto, tome aire fresco inmediatamente y consulte a

un médico. Puede haberse intoxicado con monóxido de

carbono.

Alarma de monóxido

de carbono

La page charge ...

Simplicity 020795-00 Manuel utilisateur

Marque: Simplicity

Modèle: 020795-00

Catégorie: Pulvérisateur de peinture

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

español: Simplicity 020795-00 Manual de usuario

Simplicity 020795-00 Manuel utilisateur

Simplicity 020795-00 Manuel utilisateur

dans d''autres langues

Documents connexes