Oleo-Mac BCH 40 BP Le manuel du propriétaire

GB

F

E

RUS

HR

UA

OPERATOR’S INSTRUCTION BOOK

MANUEL D’UTILISATION ET D’ENTRETIEN

MANUAL DE USO Y MANTENIMIENTO

ИНСТРУКЦИЯ ПО ЭКСПЛУАТАЦИ

UPUTSTVA ZA KORIŠTENJE I ODRŽAVANJE

ПЕРЕКЛАД ОРИГІНАЛЬНИХ ІНСТРУКЦІЙ ВСТУП

BCH 40 BP - DSH 400 BP

(40.2 cm

3

)

6

4

5

C

D

B

A

1 2

1

2

3

N

8

7

14

9

10

11

12

19

22

20

21

16

17

15

18

13

H

I

L

M

Q

P

O

F

C

L

H

N

F

D

H

F

R

C

B

L

B

A

D

A

D

4

5A

6 7

5B

8 9

E

F

B

G

A

D

B

C

B

1 2 3

A

CLOSE

B

OPEN

MAX

12÷15 cm

Ø 2,4 mm Ø 2,4 mm

810

12

11

13 14

15

A

BRUSHCUTTER

61450265

T

B

A

4

5

6

0,5 mm

L6RTC

0000000000

2018

12

13

5

3

4

6

8

7

14

1

2

10

11

9

16

17

18

19 20

21

English 2

Français 20

Español 40

Pуccкий 60

Hrvatski 80

Українська 99

2

GB

TRANSLATION OF ORIGINAL INSTRUCTIONS

To our valued customers

Thank you for selecting an Emak product.

Our network of dealers and authorized

workshops will always be at your complete

disposal for any need you may have.

INTRODUCTION

For correct use of the machine and to avoid

accidents, do not start working until you have

read this manual carefully. You will find

explanations concerning the operation of the

various parts plus instructions for necessary

checks and relative maintenance.

NOTE: The descriptions and illustrations

contained in this manual are not binding. The

manufacturer reserves the right to

undertake any modifications it deems

necessary without revising this manual.

In addition to the operating instructions, this

manual contains paragraphs that require your

special attention. Such paragraphs are marked

with the symbols described below:

WARNING: where there is a risk of an accident

or personal, even fatal, injury or serious damage

to property.

CAUTION: where there is a risk of damaging the

machine or its individual components.

WARNING

RISK OF HEARING DAMAGE

IN NORMAL CONDITIONS OF USE, THIS

MACHINE MAY EXPOSE THE OPERATOR TO A

PERSONAL DAILY NOISE LEVEL EQUAL TO OR

HIGHER THAN

85 dB (A)

CONTENTS

1. SAFETY PRECAUTIONS (precautions

for using the machine safety)

2

2. SYMBOLS AND SAFETY WARNINGS

(explanations on how to identify the

machine and the meaning of the

symbols)

4

3. MAIN COMPONENTS (position of the

main parts that make up the machine)

4

4. ASSEMBLY (explanations on how to

remove the packaging and assemble

detached parts)

4

5. STARTING 5

6. STOPPING THE ENGINE 7

7. USING THE MACHINE 8

8. TRANSPORTING 11

9. MAINTENANCE (all information

required to keep the machine at peak

efficiency)

12

10. STORAGE 14

11. ENVIRONMENTAL PROTECTION

(advice on using the machine in ways

that respect the environment)

14

12. TECHNICAL DATA (a summary of the

main specifications of the machine)

15

13. DECLARATION OF CONFORMITY 18

14. WARRANTY CERTIFICATE (a summary

of the warranty conditions)

18

15. TROUBLESHOOTING (helps you to

quickly solve any problems you may en-

counter while using the machine)

19

1. SAFETY PRECAUTIONS

WARNING

- The machine, when used correctly, is a

useful and effective tool; if used

incorrectly or without the necessary

precautions, it can be dangerous. To

ensure your safety and comfort, always

observe the safety instructions given here

below and throughout this manual.

- Exposure to vibrations through

prolonged use of combustion engine-

driven tools could cause blood vessel or

nerve damage in the fingers, hands, and

wrists of people prone to circulation

disorders or abnormal swellings.

Prolonged use in cold weather has been

linked to blood vessel damage in

otherwise healthy people. If symptoms

occur such as numbness, pain, loss of

strength, change in skin colour or texture,

or loss of feeling in the fingers, hands, or

wrists, discontinue the use of this tool and

seek medical attention.

- The ignition system of your machine

produces an electromagnetic field of very

low intensity. This field could interfere

with certain pacemakers. To reduce the

risk of serious or fatal injury, persons with

pacemakers should consult their doctor or

the manufacturer of the pacemaker

before using this machine.

3

GB

the table.

16 - All labels with health hazards must be kept

in good conditions. In case of damage or

deterioration, immediately substitute them

(Fig. 21).

17 - Do not utilize the machine for uses

different from the ones specified in the

manual (see pag. 8).

18 - Never leave the machine unattended with

the engine running.

19 - Do not start the engine with the arm not

mounted.

20 - Check the brush cutter daily to be sure that

components and safety devices are full

functioning properly.

21 - Do not attempt to carry out operations

or repairs that are not part of the normal

maintenance. See the authorised dealer.

22 - When disposing of the machine at the

end of its useful life, think of the

environment. Take your old unit to your

dealer who will be able to dispose of it in

a proper manner.

23 - Only experienced persons who are

familiar with the operation and safe use of

this machine should use it. If you lend the

blower to someone, also give them the

instruction manual and ensure that they

read it before using the machine.

24 - All saw service, other than the operations

shown in the present manual, should be

performed by competent personnel.

25 - Keep this manual on hand and consult it

before each use of the tool.

26 - Please note that the owner or the user is

responsible for any accidents or damage to

third parties or their property.

WARNING

- Never use a machine with faulty safety

equipment. The machine’s safety

equipment must be checked and

maintained as described in this section. If

your machine fails any of these checks

contact an Authorised Service Centre to

get it repaired.

- Any use of the machine not expressly

envisaged in this manual is to be

WARNING: National regulations may limit

the use of the machine.

1 - Do not operate the machine unless you

have received specic instruction on its use.

First time users must familiarise themselves

thoroughly with the operation of the

machine before working in the eld.

2 - The machine must only be used by adults

in good physical condition who are familiar

with the operating instructions.

3 - Never use the brush cutter when you are

tired or fatigued or if you have taken alcohol,

drugs or medication.

4 - Wear appropriate clothing and safety articles

such as: boots, heavy-duty trousers, gloves,

protective eyewear, ear protection and

protective helmet. Use clothing which is

close-tting but comfortable.

5 - Do not allow children to use the brush cutter.

6 - Do not allow other people to remain within

15 metres during brush cutter use .

7 - Before using the brush cutter, make sure

that the blade xing bolt is well-tightened.

8 - The brush cutter must be equipped with

the cutting accessories recommended by

the manufacturer (look pag. 16).

9 - Never use the brush cutter without the blade

guard or the head.

10 - Before starting the engine, make sure that

the blade is free to move and is not in contact

with any foreign objects.

11 - Every now and then while working, stop

the engine and check the blade. Replace it

at the rst sign of cracks or breaks.

12 - Only use the machine in well-ventilated

places, do not use in explosive or ammable

atmospheres or in closed environments.

13 - Never touch the blade or attempt any

maintenance work while the engine is

running.

14 - It is prohibited to t any device other than

that supplied by the manufacturer.

15 - Do not use a machine that has been

damaged, badly repaired, improperly

assembled or modied. Do not attempt to

remove or bypass any of the safety devices.

Only use cutting attachments indicated in

4

GB

considered improper and therefore a

source of risk to people and property.

PROTECTIVE CLOTHING

While working with the brushcutter,

always use safety protective approved

clothing. The use of protective clothing does

not eliminate injury risks, but reduces the injury

effects in case of accident. Consult your trusted

supplier to choose an adequate equipment.

The clothing must be proper and not an obstacle.

Wear adherent protective clothing. Protective

jackets and dungarees are ideal. Do not wear

clothes, scarfs, ties or bracelets that can stuck

into twigs. Tie up and protect long hair (example

with foulards, caps, helmets, etc.).

Safety shoes having skid-proof sole and anti-

piercing insert.

Wear protective goggles or face screens!

Use protections against noises; for example

noise reduction ear guards or earplugs. The

use of protections for the ear requests much

more attention and caution, because the

perception of danger audio signals (screamings,

alarms, etc.) is limited.

Wear gloves that permit the maximum

absorption of vibrations.

2. SYMBOLS AND SAFETY WARNINGS (Fig.21)

1 - Read operator’s instruction book before

operating this machine.

2 - Wear head, eye and ear protection.

3 - Wear strong boots and gloves when cutting

with metal or plastic blades.

4 - Be aware that objects can be thrown.

5 - Keep bystanders away 15 m.

6 - WARNING! – The surface can be hot!

7 - Warning! Kickback it’s danger.

8 - Purge Bulb.

9 - Type of machine: BRUSH CUTTER.

10 - Guaranteed sound power level.

11 - CE conformity marking.

12 - Serial number.

13 - Year of manufacture.

14 - Max. speed of output shaft, RPM

3. MAIN COMPONENTS (Fig.1)

1÷3 - Tools supplied

4 - Bevel gear

5 - Curved guard

6 - Nylon line head

7 - Fuel tank cap

8 - Purge Bulb

9 - Carburettor adjustment screws

10 - Muer guard

11 - Spark plug

12 - Air lter

13 - Starter Handle

14 - Choke Lever

15 - Throttle trigger lockout

16 - STOP button

17 - Throttle lever

18 - Harness

19 - Handle

20 - Shaft arm

21 - Button half-throttle

22 - Flexible drive

4. ASSEMBLY

FITTING THE SAFETY GUARD (Fig.4)

Fit the blade guard (A) to the shaft arm with screws

in a position allowing the operator to work safely (B).

NOTE: use the guard (C) only with nylon head.

Secure the guard (C) to the protection (A) by

means of the screw (D).

FITTING THE NYLON LINE HEAD (Fig. 8)

Put the upper (F) ange in place. Put the head xing

pin (H) in the appropriate hole (L) and tighten the

head (N) anti-clockwise by hand.

FITTING THE DISK (Fig. 9)

Fix the blade (R) onto the upper ange (F) making

sure that the rotation direction is correct.

Fix the lower ange (B), the cup (D) and tighten bolt

(A) anti-clockwise.

Put the pin provided in the appropriate hole (L)

to block the blade and allow the bolt (A) to be

tightened to 2.5 kgm (25 Nm).

5

GB

brush cutter to be properly balanced and at an

appropriate height from the ground.

- Put on the harness and position the buckles

(A, Fig. 10) to obtain the best brush cutter balance

and height.

5. STARTING

FUELING

WARNING: Gasoline is an extremely

ammable fuel. Use extreme caution when

handling gasoline or fuel mix. Do not smoke

or bring any re or ame near the fuel or the

unit.

· To reduce the risk of fire and burn injury,

handle fuel with care. It is highly flammable.

· Mix and store fuel in a container approved for

gasoline.

· Mix fuel outdoors where there are no sparks or

flames.

· Select bare ground, stop engine, and allow to

cool before refueling.

· Loosen fuel cap slowly to release pressure and

to keep fuel from escaping around the cap.

· Tighten fuel cap securely after refueling. Unit

vibration can cause an improperly tightened

fuel cap to loosen or come off and spill

quantities of fuel.

· Wipe spilled fuel from the unit. Move 3 metre

away from refueling site before starting

engine.

· Never attempt to burn off spilled fuel under

any circumstances.

· Do not smoke while handling fuel or while

operating the unit.

· Store fuel in a cool, dry, well ventilated place.

· Never place the machine in a combustible

area such as dry leaves, straw, paper, etc.

· Store the unit and fuel in an area where fuel

vapors cannot reach sparks or open flames

from water heaters, electric motors or

switches, furnaces, etc.

· Never take the cap off the tank when the

engine is running.

WARNING – Collar (see arrows C, Fig.9)

must locate in blade’s mounting hole.

FITTING THE HANDLE (Fig. 2)

Fit the handle onto the shaft arm and secure it

using screws (A). The handle position is calculated

depending on the requirements of the operator.

WARNING - Assemble the loop handle

(D, Fig.2) between label’s arrow (B) and rear

handle (C).

MOUNTING TRANSMISSION (Fig. 5A-B)

Pull pin (A) and insert the end of exible pipe (B)

into clutch housing (C). Make sure the end of the

exible coupling t. Insert pin (A) into the end of

the exible hole (D, Fig. 5A). Loosen and remove

the screw (F, Fig.5B). Insert exible (B) into tube (E)

making sure that exible shaft end (B) is correctly

inserted into the rigid shaft of transmission (Fig.

5B). Replace the screw (F) and tighten. Cover the

end of the exible shaft and the coupling of the

rigid tube with the guard (G). Fasten cable tube

to the exible pipe with the two clips (N, Fig.1).

FIXING THE THROTTLE CABLE (Fig. 6)

Turn the nut (Q) along the screw until in contact

with the adjuster (H). Turn the adjuster (H) until

in contact with the bracket (I). Insert the throttle

cable (L) into the support (M). Back o the adjuster

(H) so as to give 1 mm of play in the cable before

the movement of the support is induced. Unscrew

the nut (Q) to lock the adjustment.

NOTE – Take care when moving the exible tube

that the movement of the rotary valve is not

induced accidentally.

FITTING THE ELECTRICAL CABLES

Connect the electrical cables (O-P, Fig. 7) using the

appropriate clamps.

WARNING: Make sure that all

components are connected properly and all

screws tightened.

PREPARING TO WORK

HARNESS (18, Fig. 1)

Correct adjustment of the harness permits the

6

GB

ethanol) up to 10% ethanol or E10 fuel are

acceptable.

NOTE - Prepare only the quantity of mixture

required for immediate use; do not leave fuel in

the tank or a container for a long time. Were

commend the use of the additive Emak ADDITIX

2000 code 001000972 if the mixture is to be

stored for 12 months.

Alkylate gasoline

CAUTIONS – Alkylate fuels have

different density than normal fuel. Therefore

engines, set with normal fuel, need different

H jet regulation to avoid critical issues. For

this operation it’s necessary turned at a

Licensed Service Dealer.

Filling the tank

stir the mixture well before refuelling.

STARTING

Before starting the engine, make sure

that the blade is free to move and is not in

contact with any foreign objects.

The cutting attachment must not rotate

when the engine is idling. Otherwise contact

an Authorized Service Center to carry out a

check and x the problem.

WARNING: Hold the brush cutter rmly

with both hands. Always keep your body is to

the left of tube. Never use a cross-handed grip.

Left-handers should follow these instructions

too.

Keep a proper cutting stance.

Over exposure to vibrations can result in

blood-vessel or nerve injury to persons

suering with blood circulation problems. Seek

medical attention if you experience physical

symptoms such numbness, lack of feeling,

reduction in normal strength, changes in the

colour of the skin. These symptoms normally

appear in the fingers, hands or wrists.

Before starting the engine, make sure that the

throttle lever works freely.

· Never use fuel for cleaning operations.

· Take care not to get fuel on your clothing

OIL

2%-50 : 1

1

5

10

15

20

25

GASOLINE

l

0,02 (20)

0,10 (100)

0,20 (200)

0,30 (300)

0,40 (400)

0,50 (500)

l

A

(cm

3

)

This product is powered by a 2-cycle engine and

requires pre-mixing gasoline and 2-cycle oil.

Pre-mix unleaded gasoline and 2-cycle engine

oil in a clean container approved for gasoline.

RECOMMENDED FUEL: THIS ENGINE IS

CERTIFIED TO OPERATE ON UNLEADED

GASOLINE INTENDED FOR AUTOMOTIVE USE

WITH AN OCTANE RATING OF 89 ([R + M] / 2) OR

HIGHER.

Mix 2-cycle engine oil with gasoline according to

the instructions on the package.

We strongly recommend the use of 2% (1:50)

Efco - Oleo-Mac two cycle engine oil, which is

specifically formulated for all air-cooled two-

stroke engines.

The correct oil / fuel proportions shown in the

table (Fig. A) are suitable when using the

PROSINT 2 and EUROSINT 2 or an equivalent

high-quality engine oil (JASO specification FD

or ISO specification L-EGD).

CAUTION: DO NOT USE AUTOMOTIVE

OIL OR 2-CYCLE OUTBOARD OIL.

CAUTION:

- Match your fuel purchases to your

consumption; don’t buy more than you will

use in one or two months;

- Store gasoline in a tightly-closed container

in a cool, dry place.

CAUTION - For the mixture, never use a

fuel with an ethanol percentage higher than

10%; gasohol (mixture of gasoline and

7

GB

5) Push the choke lever (14, Fig.1) in OPEN

position (B, Fig.11).

6) Pull the starter cord to start the engine. Once

the machine is started, warm up the machine

for about few seconds, without touch the

throttle lever. The machine could need more

seconds to warm up with cold weather or at

high altitudes. Finally, push the throttle lever

(17, Fig.1) for deactivate the half-throttle.

CAUTION:

- Never wrap the starter cord around your

hand.

- When pulling the starter rope, do not

use the full extent of the rope as this can

cause the rope to break.

- Do not let starter rope snap back. Hold the

starter handle (13, Fig.1) and let the rope

rewind slowly.

WARNING: Once the engine is warmed

up do not use the choke to start up again.

WARNING: Use the semi-acceleration

device only in the phase of starting the engine

to cold.

BREAKING-IN THE ENGINE

The engine reaches the maximum power after

5÷8 hours of activity.

During this period of breaking-in do not use the

engine at wide open throttle without load, to avoid

excessive functioning stress.

WARNING! - During the breaking-in

period do not vary the carburetion to obtain a

presumed power increment; the engine can be

damaged.

NOTE: It is normal for smoke to be emitted

from a new engine during and after first use.

6. STOPPING THE ENGINE

Set the throttle lever to idle position (17, Fig. 1)

and wait a few seconds to let the engine cool o.

Turn o the engine, pushing the ON/OFF switch

(16).

WARNING: Follow safety instruction for

fuel handling. Always shut off engine before

fuelling. Never add fuel to a machine with a

running or hot engine. Move at least 3 m from

refuelling site before starting engine. DO

NOT SMOKE!

1. Clean surface around fuel cap to prevent

contamination.

2. Loosen fuel cap slowly.

3. Carefully pour fuel mixture into the tank.

Avoid spillage.

4. Prior to replacing the fuel cap, clean and

inspect the gasket.

5. Immediately replace fuel cap and hand

tighten. Wipe up any fuel spillage.

WARNING: Check for fuel leaks, if any

are found, correct before use. Contact a

Servicing Dealer if necessary.

Engine is Flooded

- Engage a suitable tool in the spark plug boot.

- Pry off the spark plug boot.

- Unscrew and dry off the spark plug.

- Open the throttle wide.

- Pull the starter rope several times to clear the

combustion chamber.

- Refit the spark plug and connect the spark

plug boot, press it down firmly.

- Set the choke lever to OPEN position – even

if engine is cold.

- Now start the engine.

STARTUP PROCEDURE

1) Slowly push the purge bulb 4 times (8, Fig.1).

2) Pull the choke lever (14, Fig.1) in the CLOSE

position (A, Fig.11)

3) Pull the throttle lever (17, Fig. 1) and stop it

at half-throttle by pressing the button (21),

then release the lever (17).

4) Place the brush cutter on the ground in a

stable position. Check that the blade is free.

Holding the brush cutter down (Fig.12), pull

the starter rope until the rst kick over of the

engine is heard (no more than 3 pulls). A new

unit may require additional pulls.

8

GB

• Make sure you can move and stand safely.

Check the area around you for possible

obstacles (roots, rocks, branches, ditches, etc.)

in case you have to move suddenly.

• Do not cut above chest height, as a brush

cutter held higher is difficult to control against

kickout forces.

• Do not work near electrical wires. Leave this

operation for professionals.

• Cut only when visibility and light are adequate

for you to see clearly.

• Do not cut from a ladder, this is extremely

dangerous.

• Stop the brush cutter if the blade strikes a

foreign object. Inspect the blade and brush

cutter; repair parts as necessary.

• Keep the blade out of dirt and sand. Even a

small amount of dirt will quickly dull a blade

and increase the possibility of kickout.

• Stop the engine before setting the brush

cutter down.

• Be particularly cautious and alert while

wearing hearing protection because such

equipment may restrict your ability to hear

sounds indicating danger (calls, signals,

warnings, etc).

• Be extremely cautious when working on

slopes or uneven ground.

WARNING: Never use rigid blades when

cutting in stony areas. Thrown objects or

damaged blades may result in serious or fatal

injury to the operator or bystanders. Watch

out for thrown objects. Always wear approved

eye protection. Never lean over the cutting

attachment guard. Stones, rubbish, etc. can

be thrown up into the eyes causing blindness

or serious injury. Keep unauthorised persons

at a distance. Children, animals, onlookers

and helpers should be kept outside the safety

zone of 15 m. Stop the machine immediately

if anyone approaches. Never swing the

machine around without first checking

behind you to make sure no-one is within the

safety zone.

7. USING THE MACHINE

PROHIBITED USE

WARNING: Avoid kickout which can

result in serious injury. Kickout is the

sideward or sudden forward motion of the

machine occurring when the blade contacts

any object such as a log or stone. Contacting

a foreign object can also result in loss of

brush cutter control.

WARNING! - Always follow the safety

precautions. The brush cutter must only be

used to trim grass material. Do not cut metal,

plastics, masonry. Do not use the brush cutter

as a lever to lift, move or break objects, nor

lock it on xed supports. It is forbidden to apply

tools or applications that are not the ones

indicated by the manufacturer onto the brush

cutter’s power take-o.

WARNING: When using rigid blades,

avoid cutting close to fences, sides of

buildings, tree trunks, stones or other such

objects that could cause the brush cutter to

kick out or could cause damage to the blade.

We recommends use of the nylon line heads

for such jobs. In addition, be alert to an

increased possibility of ricochets in such

situations.

WARNING: Never use of a brush cutter

with the cutting attachment perpendicular to

the ground. Never use the brushcutter for

trimming hedges.

WARNING: If the blade loosens after

being properly tightened, stop work

immediately. The retaining nut may be worn

or damaged and should be replaced. Never

use unauthorized parts to secure the blade. If

the blade continues to loosen, see your

dealer. Never use the brushcutter for

trimming hedges.

Work Area Precautions

• Always cut with both feet on solid ground to

prevent being pulled off balance.

9

GB

WARNING: Neither the operator of the

machine nor anyone else may attempt to

remove the cut material while the engine is

running or the cutting equipment is rotating,

as this can result in serious injury. Stop the

engine and cutting equipment before you

remove material that has wound around the

blade as otherwise there is a risk of injury.

The bevel gear can get hot during use and

may remain so for a while afterwards. You

could get burnt if you touch it.

WARNING: Sometimes branches or

grass get caught between the guard and

cutting attachment. Always stop the engine

before cleaning.

Check before starting

• Check the blade to ensure that no cracks have

formed at the bottom of the teeth or by the

centre hole. Discard a blade if cracks are

found.

• Check that the support flange is not cracked

due to fatigue or due to being tightened too

much. Discard the support flange if it is

cracked.

• Ensure the locking nut has not lost its captive

force. The tightening torque of the locking nut

should be 25 Nm.

• Check that the blade guard is not damaged or

cracked. Replace the blade guard if it is

cracked.

WARNING: Never use the machine

without a guard or with a defective guard.

Never use the machine without the

transmission shaft.

Forestry clearing

• Before you start clearing, check the clearing

area, the type of terrain, the slope of the

ground, whether there are stones, hollows etc.

• Start at whichever end of the area is easiest,

and clear an open space from which to work.

• Work systematically to and fro across the area,

clearing a width of around 4-5 m on each pass.

Working Techniques

General Working Instructions

WARNING: This section describes the

basic safety precautions for working with

clearing saws and trimmers. If you encounter

a situation where you are uncertain how to

proceed you should ask an expert. Contact

your dealer or your service workshop. Avoid

all usage which you consider to be beyond

your capability. You must understand the

difference between forestry clearing, grass

clearing and grass trimming before use.

Basic safety rules

1. Look around you:

• To ensure that people, animals or other things

cannot affect your control of the machine.

• To ensure that people, animals, etc., do not

come into contact with the cutting attachment

or loose objects that are thrown out by the

cutting attachment.

WARNING: Do not use the machine

unless you are able to call for help in the

event of an accident.

2. Do not use the machine in bad weather, such

as dense fog, heavy rain, strong wind, intense

cold, etc. Working in bad weather is tiring and

often brings added risks, such as icy ground,

etc.

3. Make sure you can move and stand safely.

Check the area around you for possible

obstacles (roots, rocks, branches, ditches, etc.)

in case you have to move suddenly. Take great

care when working on sloping ground.

4. Switch off the engine before moving to

another area.

5. Never put the machine down with the engine

running.

• Always use the correct equipment.

• Make sure the equipment is well adjusted.

• Organise your work carefully.

• Always use full throttle when starting to cut

with the blade.

• Always use sharp blades.

10

GB

Grass trimming with a trimmer head

CAUTION: Do not work with mowing

line longer than the intended diameter. With

a properly mounted guard, the built-in cutter

will automatically adjust the line to its proper

length. Overly long lines can overload the

engine, resulting in damage to the clutch

mechanism and nearby parts.

Trimming

• Hold the trimmer head just above the ground

at an angle. It is the end of the cord that does

the work. Let the cord work at its own pace.

Never press the cord into the area to be cut.

• The cord can easily remove grass and weeds

up against walls, fences, trees and borders,

however it can also damage sensitive bark on

trees and bushes, and damage fence posts.

• Reduce the risk of damaging plants by

shortening the cord to 10-12 cm and reducing

the engine speed.

Clearing

• The clearing technique removes all unwanted

vegetation. Keep the trimmer head just above

the ground and tilt it. Let the end of the cord

strike the ground around trees, posts, statues

and the like.

CAUTION: This technique increases the

wear on the cord.

• The cord wears quicker and must be fed

forward more often when working against

stones, brick, concrete, metal fences, etc., than

when coming into contact with trees and

wooden fences.

• When trimming and clearing you should use

less than full throttle so that the cord lasts

longer and to reduce the wear on the trimmer

head.

Cutting

• The trimmer is ideal for cutting grass that is

difficult to reach using a normal lawn mower.

Keep the cord parallel to the ground when

cutting. Avoid pressing the trimmer head

This exploits the full reach of the machine in

both directions and gives the operator a

convenient and varied working area to work

in.

• Clear a strip around 75 m long. Move your fuel

can as work progresses.

• On sloping ground you should work along the

slope. It is much easier to work along a slope

than it is to work up and down it.

• You should plan the strip so that you avoid

going over ditches or other obstacles on the

ground. You should also orient the strip to

take advantage of wind conditions, so that

cleared stems fall in the cleared area of the

stand.

Grass clearing using a grass blade

• Grass blades and grass cutters must not be

used on woody stems.

• A grass blade is used for all types of tall or

coarse grass.

• The grass is cut down with a sideways,

swinging movement, where the movement

from right-to-left is the clearing stroke and the

movement from left-to-right is the return

stroke. Let the left-hand side of the blade

(between 8 and 12 o’clock) do the cutting.

• If the blade is angled to the left when clearing

grass, the grass will collect in a line, which

makes it easier to collect, e.g. by raking.

• Try to work rhythmically. Stand firmly with

your feet apart. Move forward after the return

stroke and stand firmly again.

• Let the support cup rest lightly against the

ground. It is used to protect the blade from

hitting the ground.

• Reduce the risk of material wrapping around

the blade by following these instructions:

1. Always work at full throttle.

2. Avoid the previously cut material during the

return stroke.

• Stop the engine, unclip the harness and place

the machine on the ground before you start to

collect the cut material.

11

GB

against the ground as this can ruin the lawn

and damage the tool.

• Do not allow the trimmer head to constantly

come into contact with the ground during

normal cutting. Constant contact of this type

can cause damage and wear to the trimmer

head.

Sweeping

• The fan effect of the rotating cord can be used

for quick and easy clearing up. Hold the cord

parallel to and above the area to be swept and

move the tool to and fro.

• When cutting and sweeping you should use

full throttle to obtain the best results.

WARNING: Never cut, when visibility is

poor or in very high or low temperatures or in

freezing weather.

8. TRANSPORTING

TRANSPORTION

Carry the brush cutter with the engine o and with

the protective blade cover on (Fig. 3).

ATTENTION: Fit the disk protection p.n.

4196086 as shown (Fig. 3) before transporting or

storing the brushcutter.

WARNING – When transporting the

machine in a vehicle, ensure that it is properly

secured using belts. The machine should be

transported in a horizontal position with the tank

empty, ensuring compliance with applicable

regulations for transport of such machines.

12

GB

Please note that the following maintenance intervals apply for normal operating conditions only. If your daily work

requires longer than normal or harsh cutting conditions are present, then the suggested intervals should be shortened

accordingly.

Complete Machine

Inspect (Leaks, Cracks, and Wear)

x

Clean after finishing daily work

Check Operation

Inspect (Leaks, Cracks, and Wear)

Inspect

Inspect (Damage, Sharpness, and Wear)

Inspect (Damage, Wear and Grease Level)

Clean

Controls (STOP button, Choke Lever, Throttle

Trigger, Trigger interlock)

Fuel Tank

Fuel Filter and tube

Cutting Attachments

Cutting Attachments Guard

All Accessible Screws and Nuts (Not Adjusting Screws)

Air Filter

Before Each Use

Monthly

As Required

1 year or 100 hrs.

Cylinder Fins

Starter System Vents

Carburetor

Spark Plug

Vibration Mounts

Cutting Attachments nuts and screws

Clean, Replace Filter Element

Check Tension

Replace

Inspect

Retighten

Clean

Clean after finishing daily work

Replace

Check Electrode Gap

Inspect (Damage, and Wear)

Replace by Dealer

Check that the locking nut of the cutting

equipment is tighten correctly

Replace

Check Idle (Cutting Attachments must not

rotate at idle)

Replace

Inspect (Damage, and Wear)

x

Maintenance Chart

Sharpen

Bevel Gear

x

Inspect (Damage, and Wear)

Starter Rope

x

If Damaged or

Faulty

9. MAINTENANCE

13

GB

WARNING! – Always wear protective

gloves during maintenance operations. Do not

carry out maintenance with the engine hot.

AIR FILTER

Every 8-10 working hours, remove the cover (A,

Fig. 19), clean the lter (B).

Blow with compressed air, at a distance.

Replace if dirty or damaged. The engine runs

irregularly if the lter is clogged, with consequent

higher consumption and lower performance.

FUEL FILTER

Check fuel lter periodically. A dirty lter can cause

dicult starting and lower engine performance.

To clean lter proceed as follows: remove it from

fuel lling hole. Replace it (Fig. 17) if too dirty.

ENGINE

Clean cylinder ns with a brush or compressed

air periodically. Dangerous overheating of engine

may occur due to impurities on the cylinder.

SPARK PLUG

Clean spark plug and check electrode distance

periodically (Fig. 18). Use TORCH L6RTC or of other

brand with the same thermal grade.

GEAR HOUSING

Every 30 working hours, remove screw (D, Fig. 6)

on the gear housing and check the quantity of

grease. Do not use more than 10 grams. Use high

quality molybdenum bisulde grease.

Never use fuel for cleaning operations.

TRASMISSION

Grease the joints of the exible (B, Fig.20) every

20 working hours with molybdenum disulde.

Grease the joints of the rigid tube (D, Fig. 20) every

30 working hours with molybdenum disulde.

CARBURETOR

Before adjusting the carburetor, clean the air lter

(B, Fig. 19) and warm up the engine.

BLADE SHARPENING 234 TOOTH

1. Blades are reversible: when one side is no

longer sharp, the blade can be turned over

and used on the other side (Fig. 13).

2. Blades are sharpened using a at single-cut

le (Fig. 13).

3. To maintain the correct balance, le all cutting

edges uniformly.

4. If the blades are not sharpened correctly, this

can set up abnormal vibrations in the machine

and cause the blades themselves to break

ultimately.

WARNING! – The wrong type of cutter or

an incorrectly sharpened blade will increase the

risk of kickback. Check mower blades for

deterioration or cracks, and replace if damaged.

WARNING: Never repair damaged

cutting attachments by welding,

straightening or modifying the shape. This

may cause parts of the cutting tool to come

off and result in serious or fatal injuries.

NYLON LINE HEAD

Only use line of the same diameter as the original

to avoid overloading the engine (Fig. 14).

In order to get more line out of the cutting head,

tap it lightly on the ground while working.

Note: Never hit the nylon head against hard spots

such as concrete or stones, it could be dangerous.

Replacing the nylon line on the TAP&GO

trimmer head (Fig.15)

1 - Press the tab (1, Fig. 15) and remove the cover

and the internal spool.

2 - Double back the line, leaving one end 14 cm

longer than the other one. Lock the line in the

notch (2, Fig. 15). Wind the line in the direction

of the arrow, each end in its chink, regulary,

without crossing them.

3 - At the end of the winding, lock in the slits (3,

Fig. 15) Assemble the spring. Thread the line

through the eyelets (4) (g.15), secure the

head with the cover (5) and then pull the line

outwards from the head (6).

14

GB

- Remove the blade xing anges, clean, dry

and lubricate the bevel gear seat.

- Empty the fuel tank and put the cap back on.

- Thoroughly clean the cooling slots and the air

lter (B, Fig. 19).

- Store the brush cutter in a dry place, preferably

not in direct contact with the oor and away

from heat sources.

11. ENVIRONMENTAL PROTECTION

Environmental protection should be a priority of

considerable importance when using the

machine, for the benefit of both social cohesion

and the environment in which we live.

- Try not to cause any disturbance to the

surrounding area.

- Scrupulously comply with local regulations

and provisions for the disposal of waste

materials after mowing.

- Scrupulously comply with local regulations

and provisions for the disposal of oils, petrol,

batteries, filters, deteriorated parts or any

elements which have a strong impact on the

environment. This waste must not be

disposed of as normal waste, it must be

separated and taken to specified waste

disposal centres where the material will be

recycled.

Demolition and disposal

When the machine reaches the end of its service

life, do not dispose of it into the environment;

instead take it to a waste disposal centre.

Most materials used in the manufacture of the

machine are recyclable; all metals (steel,

aluminium, brass) can be delivered to a normal

recycling station. For information contact your

local waste recycling service. Waste disposal

must be carried out with respect for the

environment, avoiding soil, air and water

pollution.

In all cases, applicable local legislation must

be complied with.

When the machine is scrapped also the CE mark

label must be destroyed together with this

manual.

Idle screw T is adjusted in order to ensure a good

safety margin between idle running and clutch

engagement.

WARNING: With the engine idling (3000

rpm), the blade should not rotate. We

recommend that you have your nearest

authorised dealer or service workshop carry

out any carburettor adjustments.

WARNING: Weather conditions and

altitude may aect carburation.

EXTRA MAINTANANCE ADVISABLE

It is advisable to inspect the machine by a

specialized technician at an authorized service

network at the end of season, if used

intensively, and every two years if with normal

use.

ATTENTION: All maintenance operations

not reported in this manual must be carried

out by an authorized Service Center.

To ensure steady and regular brush cutter

operation, remember that parts must only be

replaced with ORIGINAL SPARES.

Any unauthorized changes and/or use

of non-original replacement parts may result

in serious injury or death to the operator or

third parties.

10. STORAGE

If the machine is to be stored for long periods:

- Drain and clean the fuel tank in a well-ventilated

area. To drain the tank, start the engine and

wait until the fuel is exhausted and the engine

stops (leaving fuel mixture in the carburettor

could damage the membranes).

- The procedures for returning the machine to

service following winter storage are the same

as for starting up during everyday use (page 7).

- Follow all the maintenance regulations

previously described.

- Clean the brush cutter completely and lubricate

the metallic parts.

- Remove, clean and lubricate the blade to

prevent rusting.

La page charge ...

Oleo-Mac BCH 40 BP Le manuel du propriétaire

Ce manuel convient également à

Oleo-Mac BCH 40 BP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents