Whirlpool UXT3030ADB0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: UXT3030ADB0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

UXT3030ADW0

30" (76.2 CM) RANGE HOOD

Forquestions about features, operation/performance, parts, accessories or service,call: 1-800-253-1301

or visit our website at www, whirlpool,com

InCanada, call 1-800-807-6777 or visit our website at www,whirlpool,ca

HOTTED'ASPIRATIONDE

30"(76,2 CM)

Au Canada, pour assistance, installation ou service, composer

le 1-800-807-6777 ou visiter notre site Web&

www.whirlpool.ca

Table of Contents/Table des matieres ............................................................................. 2

// _ _ UXT303OAD

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTlUSATION Rg:SIDENTIELLE UNIQUEMENT.

RANGEHOOD SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

LI318C/W10646401C

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

iMPORTANT SAFETY iNSTRUCTiONS

WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK, OR INJURY TO PERSONS, OBSERVE THE

FOLLOWING:

m Use this unit only in the manner intended by the

manufacturer. Ifyou have questions, contact the

manufacturer.

m Before servicing or cleaning the unit, switch power off at

service panel and lock the service disconnecting means to

prevent power from being switched on accidentally. When

the service disconnecting means cannot be locked,

securely fasten a prominent warning device, such as a tag,

to the service panel.

m Installation work and electrical wiring must be done by

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction.

m Do not operate any fan with a damaged cord or plug.

Discard fan or return to an authorized service facility for

examination and/or repair.

m Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National Fire

Protection Association (NFPA), the American Society for

Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

m When cutting or drilling into wall or ceiling; do not damage

electrical wiring and other utilities.

m Ducted fans must always be vented outdoors.

CAUTION: For general ventilating use only. Do not use

to exhaust hazardous or explosive materials and vapors.

CAUTION: To reduce risk of fire and to properly exhaust

air, be sure to duct air outside - do not vent exhaust air into

spaces within walls or ceilings, attics or into crawl spaces,

or garages.

WARNING: TO REDUCE THE RISK OF FIRE, USE ONLY

METAL DUCTWORK.

WARNING: TO REDUCE THE RISK OF A RANGE TOP

GREASE FIRE:

m Never leave surface units unattended at high settings.

Boilovers cause smoking and greasy spillovers that may

ignite. Heat oils slowly on low or medium settings.

m Always turn hood ON when cooking at high heat or when

flambeing food (i.e. Crepes Suzette, Cherries Jubilee,

Peppercorn Beef Flamb6).

m Clean ventilating fans frequently. Grease should not be

allowed to accumulate on fan or filter.

m Use proper pan size. Always use cookware appropriate for

the size of the surface element.

WARNING: TO REDUCE THE RISK OF INJURY TO

PERSONS IN THE EVENT OF A RANGE TOP GREASE

FIRE, OBSERVE THE FOLLOWING: a

m SMOTHER FLAMES with a close fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO

PREVENT BURNS. Ifthe flames do not go out

immediately, EVACUATE AND CALL THE FIRE

DEPARTMENT.

m NEVER PICK UP A FLAMING PAN - you may be burned.

m DO NOT USE WATER, including wet dishcloths or towels -

a violent steam explosion will result.

m Use an extinguisher ONLY if:

- You know you have a class ABC extinguisher, and you

already know how to operate it.

- The fire is small and contained in the area where it

started.

- The fire department is being called.

- You can fight the fire with your back to an exit.

aBased on "Kitchen Fire Safety Tips" published by NFPA.

m WARNING: To reduce the risk of fire or electrical shock,

do not use this fan with any solid-state speed control

device.

READ AND SAVE THESE INSTRUCTIONS

TABLEOF CONTENTS

RANGE HOOD SAFETY ................................................................. 1

INSTALLATION REQUIREMENTS ................................................ 3

INSTALLATION INSTRUCTIONS .................................................. 6

RANGE HOOD USE ...................................................................... 10

RANGE HOOD CARE ................................................................... 10

WIRING DIAGRAM ....................................................................... 11

ASSISTANCE OR SERVICE ......................................................... 12

WAR RANTY .................................................................................. 13

TABLEDESMATIERES

SI_CURITI_ DE LA HOTTE DE CUlSINIi=RE ................................ 14

EXIGENCES D'INSTALLATION ................................................... 16

INSTRUCTIONS D'INSTALLATION ............................................. 19

UTILISATION DE LA HOTTE ....................................................... 23

ENTRETIEN DE LA Ho'n'E .......................................................... 23

SCHI_MA DE C.,&,BLAGE............................................................... 24

ASSISTANCE OU SERVICE ......................................................... 25

GARANTIE ..................................................................................... 26

INSTALLATIONREQUIREMENTS

c nd

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools needed

Metal snips

#2 Phillips

screwdriver

Wire stripper

Flat-blade

screwdriver

Parts supplied

Remove parts from package. Check that all parts are included.

(4.2 X 25 mm)

flat-head screws

anchors brackets

sw' xto" (8,3x254ore)

!ectangular dampe r

Parts needed

IUE LstediCSA Listed/CSA 1!20v, I

Approved U U I APprOVed 1_,,(13 mm)_ I maxirnum, I

wire C0n_eet0rs I strain relief I! ype E26 , q_ I

I inc_noescen_amp!

For 3V4" x 10" (8.3 x 25.4 cm} rectangular vented installations

Duct tape @

Optional accessories

Power

wall or roof caP

*For information on ordering, see the "Assistance or Service"

section.

IMPORTANT: Observe all governing codes and ordinances.

• It is the installer's responsibility to comply with installation

clearances specified on the model/serial rating plate. The

model/serial rating plate is located inside the range hood on

the left wall.

• Range hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

• Cabinet opening dimensions that are shown must be used.

Given dimensions provide minimum clearance. Consult the

cooktop/range manufacturer installation instructions before

making any cutouts.

• This range hood is recommended for use with cooktops with

a maximum total rating of 40,000 Btus or less.

• Grounded electrical outlet is required. See "Electrical

Requirements" section.

• All openings in ceiling and wall where range hood will be

installed must be sealed.

These range hoods are factory set for vented installations.

Models that are capable of being installed as non-vented

(recirculating) require charcoal filters. See the "Assistance or

Service" section for information on ordering charcoal filters.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

2" -"/_ 69/Io'' (16.7cm)

415/16"

(12.5 cm)

291%6"(76.0cm)

1 "

(2.5 crn)

18%"

cm)

Venting Methods

NOTES:

• Flexible vent is not recommended. Flexible vent creates both

back pressure and air turbulence that greatly reduce

performance.

• The vent system is optional for this model.

Vent system can terminate either through the roof or wall. Use

3V4" x 10" (8.3 x 25.4 cm) rectangular with a maximum vent

length of 35 ft (10.7 m).

Top Venting Wall Venting

Installation Clearances

A. 24" (61.0 cm) minimum distance from electric cooking surface.

24" (61.0 cm) minimum distance from gas cooking surface.

30" (76.2 cm) suggested maximum above the cooking surface.

B. 18" (45.7 cm) minimum clearance - upper cabinet to countertop.

C. 30" (76.2 cm) minimum cabinet opening width.

D. 12" (30.5 cm) cabinet depth.

E.36" (91.4 cm) base cabinet heighL

/ _}t S

A. 3V4"x 10" (8.3 x 25.4 cm)

rectangular vent through the

roof (purchased separately).

B. Roof cap with damper

(purchased separately)

A. 3V4" x 10" (8.3 x 25.4 cm)

rectangular vent through the

waft or out the top (purchased

separately).

B. Waft cap with damper

(purchased separately)

Cold Weather Installations

An additional back draft damper should be installed to minimize

backward cold air flow and athermal break should be installed to

minimize conduction of outside temperatures as part of the vent

system. The damper should be on the cold air side of the thermal

break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of air

movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in your

area.

Venting Requirements

Vent system must terminate to the outdoors.

Do not terminate the vent system in an attic or other enclosed

area.

Do not use a 4" (10.2 cm) laundry-type wall cap.

Use 3V4" x 10" (8.3 x 25.4 cm) rectangular metal vent,

depending on your installation requirement. Rigid metal vent

is recommended. Plastic or metal foil vent is not

recommended.

The length of vent system and number of elbows should be

kept to a minimum to provide efficient performance.

For the most efficient and quiet operation:

• Use no more than three 90° elbows.

• Make sure there is a minimum of 24" (61 cm) of straight vent

between the elbows if more than 1 elbow is used.

• Do not install 2 elbows together.

• Use clamps or duct tape to seal all joints in the vent system.

• The vent system must have a damper. If roof or wall cap has a

damper, do not use damper supplied with the range hood.

• Use caulking to seal exterior wall or roof opening around the

cap.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Vent System

Vent Piece

90° elbow 5.0 ft

(1.5 m)

31/4'' x 10" (8.3 cm x 12.0 ft

25.4 cm) flat elbow (3.7 m)

7" (17.8 cm) wall cap 0.0 ft

(o.o m)

31/4"x 10" (8.3 cm x 4.5 ft

25.4 cm) to 7" (17.8 cm) (1.4 m)

31/4"x 10" (8.3 cm x 5.0 ft

25.4 cm) to 7" (17.8 cm) (1.5 m)

90° elbow

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70 (latest

edition), or CSA Standards C22.1-94, Canadian Electrical Code,

Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

If codes permit and aseparate ground wire is used, it is

recommended that a qualified electrician determine that the

ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

• A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

• If the house has aluminum wiring, follow the procedure

below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section of

copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial rating plate.

The model/serial plate is located behind the filter on the rear

wall of the range hood.

Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22.1-94, Canadian Electrical Code, Part 1 and

C22.2 No. 0-M91 (latest edition) and all local codes and

ordinances.

Example vent system

90 ° elbow

2ft (0.6m)

_i_

6tt(1.Sm) ..................._JWallcap

1 - 90 ° elbow

1 - wall cap

8 ft (2.4 m) straight

System length

= 5.0 ft (1.5 m)

= 0.0 ft (0.0 m)

= 8.0 ft (2.4 m)

= 13.0 ft (3.9 m)

Maximum Recommended Length

31/4"x 10" (8.3 x 25.4 cm)

Rectangular Vent = 35 ft (10.7 m)

INSTALLATIONINSTRUCTIONS

NOTES:

Depending on your model, determine which venting method

to use: roof or wall.

It is recommended that the vent system be installed before

the range hood is installed. Go to "Venting System" in the

"Installation Requirements" section if you need assistance.

• Before making cutouts, make sure there is proper clearance

within the ceiling or wall for the vent system.

1. Disconnect Power

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

2. Mark Hole Locations

3. Install Brackets

• Using a #2 Phillips screwdriver, install the drywall anchors.

• Using #8-18 x 1" (4.2 x 25 mm) flat-head #2 Phillips screws,

install the mounting brackets using the upper holes.

NOTE: For installations to a surface other than drywall, it is

recommended that a qualified contractor determine the

anchoring method.

4. Prepare Range Hood

Align the exterior edge of the mounting brackets with the exterior

edges of the upper cabinet.

IMPORTANT: The brackets should touch the upper cabinet.

With a pencil, mark the upper holes on the brackets.

• Set the range hood on its back on a covered surface.

• Using a #2 Phillips screwdriver, remove the rectangular

damper attached with 3.5 x 9.5 mm screws.

• Using a #2 Phillips screwdriver, remove the electrical box

cover.

• Using a flat-blade screwdriver, remove the appropriate power

supply knockout.

5. Mark Hole Locations

Lift the range hood into place and insert the mounting bracket

tabs through the slots in the back of the range hood.

Hold the range hood firmly in place with one hand and bend each

mounting tab (A) upward approximately 90 °.

OPTIONAL: Mark the hole in each mounting tab.

Mark the hole at the power supply knockout (B).

For a top vented installation: Mark the 4 vent hole locations (C)

on the top of the range hood.

For a rear vented installation: Mark the 4 vent hole locations (D)

on the rear of the range hood.

OPTIONAL: Mark the hole in each mounting tab.

Remove the range hood and set it aside.

6. Mark and Cut Vent Opening

31/4'' X 10" (8.3 X 25.4 cm) Rectangular Vent System

• Using a 1/2"(13 mm) drill bit, drill a hole in each of the dots

marked previously on either the wall or upper cabinet. Using

the outside edges of the holes, mark the vent opening.

• Using a jigsaw or keyhole saw, cut the vent opening.

7. Drill Electrical Opening

Using a 11/4"(3 cm) drill bit, drill the hole in the dot marked

previously at the electrical strain relief.

OPTIONAL: Using a 1/8"(3 mm) drill bit, drill pilot holes for the

dots marked previously at each mounting tab at an approximate

45° angle in an upward direction.

8. Prepare Range Hood Vents and

Mounting Tabs

10. Mount Range Hood

• Install Strain Relief

Install a UL Listed/CSA Approved 1/2"(13 mm) strain relief (A).

• Mounting Tabs

Start a #8-18 x %" (4.2 x 16 ram) truss-head screw into the

mounting tab (D) on each side of the range hood as shown in

the inset. Insert the screws approximately 2 turns into the

mounting tab holes.

• 31/4'' x 10" (8.3 x 25.4 cm) Rectangular Vent Installations

For top vent installations, remove the top, rectangular vent

knockout (C).

For wall vent installations, remove the rear rectangular vent

knockout (B).

9. Attach Vent Damper or Transition

3%"x 10" (8.3 x 25.4 cm) Rectangular Vent Damper

Lift the range hood into place, positioning the rear slots over

the mounting brackets.

Using a Phillips screwdriver, push on the screws that are

started into the top mounting tabs and bend the tabs against

the cabinet side walls. Attach the screws to the cabinet side

walls.

IMPORTANT: Do not overtighten the screws.

For direct wire installations, run the home power supply cable

according to the National Electric Code or CSA standards

and local codes and ordinances. There must be enough

wiring from the fused disconnect (or circuit breaker) box to

make the connection in the range hood electrical terminal

box.

• Tighten the strain relief screws.

NOTE: Do not reconnect power until the installation is

complete.

OPTIONAL: Ifyou prefer, bend the rear tabs against the rear

of the range hood and attach to the wall using #8-18 x 5/8"

(4.2 x 16 mm) truss-head screws.

] 1. Connect Vent System

• Connect the ventwork to the range hood.

• Seal joints with duct tape to make secure and airtight.

• Check that the back draft dampers work properly.

Using (2) short Phillips head screws, install the 31/4'' x 10" (8.3 x

25.4 cm) rectangular damper over the top or rear vent knockout

removed in Step 8.

NOTE: If the wall cap used has a damper and it interferes with

the rectangular damper, remove the rectangular damper flap.

12. Make Electrical Connection

Option 1 - Direct Wire Installations

• Use a UL Listed/CSA Approved wire connector and connect

the 2 white wires (A) together.

• Use a UL Listed/CSA Approved wire connector and connect

the 2 black wires (B) together.

Option 2 - Power Cord Kit Installations

For optional power cord kit installations, follow the instructions

supplied with the power cord kit. See the "Assistance or Service"

section for information on ordering.

NOTE: Use only with range hood cord connection kits that have

been investigated and found acceptable for use with this model

range hood.

13. Complete the Installation

• Install a 120V, 75W maximum, incandescent light bulb with

E26 base. See "Replacing the Incandescent Light Bulb" in the

"Range Hood Care" section.

• If removed previously, replace the filter. See "Metal Grease

Filter" in the "Range Hood Care" section.

For vented installations: Install a metal filter.

• Check the operation of the range hood fan and light. See the

"Range Hood Use" section.

If the range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

Disconnect the power and check the wiring connections.

NOTE: To get the most efficient use from your new range hood,

read the "Range Hood Use" section.

Fire Hazard

Electrically ground the blower.

Use copper wire.

Connect ground wire to green ground screw in

terminal box.

Failure to do so can result in death, fire, or

electrical shock.

• Connect the green (or bare) ground wire (C) from the power

supply to the green ground screw in the electrical box and

tighten the screw securely.

Reinstall the electrical box cover.

Reconnect power.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the hood

before cooking and allow it to operate several minutes after the

cooking is complete to clear all smoke and odors from the

kitchen.

The hood controls are located on the front panel of the range

hood.

B C

A. Incandescent light housing and cover

B. Grease filter retainer

C. Grease filter

ContR,> S

Off

On@Off Low@ High

! !

A. Fan speed switch

B. On/Off light switch

Operating the light

Press the light switch to the left to turn the light On.

Press the light switch to the right to turn the light Off.

Operating the fan

The fan has 2 speeds.

Press the fan switch to the left for Low speed.

Press the fan switch to the right for High speed.

Return the fan switch to the center to turn the fan Off.

RANGE HOOD CARE

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace the grease filter

before operating hood.

Exterior Surfaces:

IMPORTANT: Do not use soap-filled scouring pads, abrasive

cleaners, cooktop polishing creme, steel wool, gritty washcloths

or paper towels.

To avoid damage to the stainless steel, do not use cleaners that

contain chlorine.

Cleaning Method:

• Liquid detergent or all-purpose cleaner:

Rinse with clean water and dry with a soft, lint-free cloth.

• Glass cleaner to remove fingerprints.

• For stainless steel models rub in the direction of the grain to

avoid scratching or damaging the surface.

• For stainless steel models, use Stainless Steel Cleaner /_

and Polish, Part Number 31462A (not included): See

the "Assistance or Service" section to order.

Metal Grease Filter

To Clean the Filter:

1. Remove the screw from the greasefilter retainer.

2. Turnthe grease filter retainerto releasethe filter.

A. Filter retainer

3. Wash the metal filter as needed in a dishwasher or hot

detergent solution.

To Replace the Filter:

1. To reinstall the filter, place the back edge of the filter into the

channel at the rear of the hood. Push the filter into place and

turn the filter retainer to secure the filter to the range hood.

2. Replace the screw in the grease filter retainer.

Replacing the Incandescent Light Bulb

Turn off the range hood and allow the light bulb to cool.

1. Disconnect power.

2. Squeeze the plastic lens cover and remove it from the hood.

3. Screw a 120V, 75W maximum, incandescent light bulb with

E26 base into the socket.

4. Replace the lens cover by squeezing the cover and inserting

the tabs into the slots.

5. Reconnect power.

If the new light does not operate, make sure the light bulb is

inserted correctly before calling service.

WIRING DIAGRAM

SE116B I

LightSwitch

On- Off

/ \

\ /

/ \

MotorCharacteristics

PowerSupply 120VAC

Frequency 60 Hz

Amperage 0.9 +10%A

WattageRating 50 +10%Watts

MotorResistance

White- Red 22.3 +10%Ohms

White- Black 13.4 +10% Ohms

MotorSwitch

Low- Off- High

Ground

Screw

GND

ASSISTANCEOR SERVICE

If you need service

Please refer to the warranty page in this manual.

If you need replacement parts

If you need to order replacement parts, we recommend that you

use only factory specified parts. Factory specified parts will fit

right and work right because they are made with the same

precision used to build every new appliance.

To locate factory specified replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

n LSA,

Call the Whirlpool Customer eXperience Center toll free:

1-800-253-1301 or visit our website at www.whirlpool.com.

Our consultants provide assistance with:

• Scheduling of service. Whirlpool designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in the United States.

• Features and specifications on our full line of appliances.

• Referrals to local dealers.

• Installation information.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Specialized customer assistance (Spanish speaking, hearing

impaired, limited vision, etc.).

For further assistance

If you need further assistance, you can write to Whirlpool

Corporation with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

Call the Whirlpool Canada LP Customer eXperience Centre toll

free: 1-800-807-6777 or visit our webpage www.whirlpool.ca.

Our consultants provide assistance with:

• Scheduling of service. Whirlpool designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

• Features and specifications on our full line of appliances.

• Referrals to local Whirlpool dealers.

• Use and maintenance procedures.

• Accessory and repair parts sales.

• Referrals to local dealers, repair parts distributors, and

service companies. Whirlpool Canada LP designated service

technicians are trained to fulfill the product warranty and

provide after-warranty service, anywhere in Canada.

For further assistance

If you need further assistance, you can write to Whirlpool

Canada LP with any questions or concerns at:

Whirlpool Brand Home Appliances

Customer eXperience Centre

Whirlpool Canada LP

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

WHIRLPOOL ®

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

• Name, address and telephone number

• Model number and serial number

• A clear, detailed description of the problem

• Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

[]

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S.

and Canada, direct all requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.

If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.

www.whirlpool.com/product_help

For one year from the date of purchase, when this major

appliance is installed, operated and maintained according to

instructions attached to or furnished with the product,

Whirlpool Corporation or Whirlpool Canada LP (hereafter

"Whirlpool") will pay for Factory Specified Replacement

Parts and repair labor to correct defects in materials or

workmanship that existed when this major appliance was

purchased, or at its sole discretion replace the product. In

the event of product replacement, your appliance will be

warranted for the remaining term of the original unit's

warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be provided by a

Whirlpool designated service company. This limited

warranty is valid only in the United States or Canada and

applies only when the major appliance is used in the country

in which it was purchased. This limited warranty is effective

from the date of original consumer purchase. Proof of

original purchase date is required to obtain service under

this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with

published user, operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not

in accordance with electrical or plumbing codes or correction of household

electrical or plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation

solutions, etc.).

5. Conversion of products from natural gas or L.P. gas.

6. Damage from accident, misuse, abuse, fire, floods, acts of God or use with

products not approved by Whirlpool.

7. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration or modification of the appliance.

8. Cosmetic damage including scratches, dents, chips, and other damage to the

appliance finishes unless such damage results from defects in materials and

workmanship and is reported to Whirlpool within 30 days.

9. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive

environments including but not limited to high salt concentrations, high moisture

or humidity or exposure to chemicals.

10. Food or medicine loss due to product failure.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an

authorized Whirlpool servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,

decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that

interfere with servicing, removal or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed,

altered or not easily determined.

The cost of repair or replacement under these excluded circumstances shall

be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you

specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Whirlpool or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

1/14

SECURITEDELA HOTTEDECUISINIERE

Votre securite et celle des autres est tres importante.

Nous donnons de nombreux messages de s_curit_ importants dans ce manuel et sur votre appareil m_nager. Assurez-vous de

toujours lire tousles messages de s_curit_ et de vous y conformer.

Voici le symbole d'alerte de s_curit&

Ce symbole d'alerte de s_curit_ vous signale les dangers potentiels de d_c_s et de blessures graves & vous

et & d'autres.

Tousles messages de s_curit_ suivront le symbole d'alerte de s_curit_ et le mot "DANGER" ou

"AVERTISSEMENT". Ces mots signifient •

Risque possible de d_cbs ou de blessure grave si vous ne

suivez pas imm_diatement les instructions.

Risque possible de d_cbs ou de blessure grave si vous

ne suivez pas les instructions.

Tousles messages de s_curit_ vous diront quel est le danger potentiel et vous disent comment r_duire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Avertissements de la proposition 65 de I'¢:tat de Californie "

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour 6tre & I'origine de

cancers.

AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'¢:tat de Californie pour 6tre a I'origine de

malformations et autres d6ficiences de naissance.

llVIPORTANTES iNSTRUCTiONS DE Sl CURITl

AVERTISSEMENT : POUR REDUIRE LE RISQUE

D'INCENDIE, CHOC ¢:LECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

m Utiliser cet appareil uniquement dans les applications

envisag6es par le fabricant. Pour toute question, contacter

le fabricant.

m Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre I'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour emp6cher tout r6tablissement accidentel de

I'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller letableau de disjoncteurs, placer sur le tableau

de disjoncteurs une 6tiquette d'avertissement pro6minente

interdisant le r6tablissement de I'alimentation.

m Tout travail d'installation ou c&blage 61ectrique doit 6tre

r6alis6 par une personne qualifi6e, dans le respect des

prescriptions de tousles codes et normes applicables, y

compris les codes du b&timent et de protection contre les

incendies.

m Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommag6(e). Jeter le ventilateur ou le retourner

& un centre de service agr66 pour examen et/ou r6paration.

m Une source d'air de d6bit suffisant est n6cessaire pour le

fonctionnement correct de tout appareil a gaz (combustion

et 6vacuation des gaz & combustion par la chemin6e), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de 1'6quipement de chauffage et

les prescriptions des normes de s6curit6 - comme celles

publi6es par la National Fire Protection Association (NFPA)

et I'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorit6s r6glementaires locales.

m Lors d'op6rations de d6coupage et de per£age dans un mur

ou un plafond, veiller a ne pas endommager les c&blages

61ectriques ou canalisations qui peuvent s'y trouver.

m Les ventilateurs d'6vacuation doivent toujours d6charger

I'air a I'ext6rieur.

MISE EN GARDE : Cet appareil est con£_uuniquement

pour la ventilation g6n6rale. Ne pas I'utiliser pour I'extraction

de mati_res ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et 6vacuer ad6quatement les gaz, veiller & acheminer I'air

aspir6 par un conduit jusqu'& I'ext6rieur - ne pas d6charger

I'air aspir6 dans un espace vide du b&timent comme une

cavit6 murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR R}_DUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MC:TALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE :

=1Ne jamais laisser un 616ment de surface fonctionner &

puissance de chauffage maximale sans surveillance. Un

renversement/d6bordement de mati_re graisseuse pourrait

provoquer une inflammation et la g6n6ration de fum6e.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

=1Veiller &toujours faire fonctionner le ventilateur de la hotte

Iors de la cuisson avec une puissance de chauffage 61ev6e

ou Iors de la cuisson d'un mets & flamber (& savoir cr6pes

Suzette, cerise jubil6e, steak au poivre flamb6).

=1Nettoyer fr6quemment les ventilateurs d'extraction. Veiller &

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

=1Utiliser toujours un ustensile de taille appropri6e. Utiliser

toujours un ustensile adapt6 & la taille de 1'616ment

chauffant.

AVERTISSEMENT : POUR RC:DUIRE LE RISQUE DE

DOMMAGES CORPORELS APR_:S LE DECLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINI_:RE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :a

=1Placer sur le r6cipient un couvercle bien ajust6, une t61e&

biscuits ou un plateau m6tallique POUR ETOUFFER LES

FLAMMES, puis 6teindre le brOleur. VEILLER ,&.¢:VITER

LES BRULURES. Si les flammes ne s'6teignent pas

imm6diatement, CVACUER LA PIECE ET APPELER LES

POMPIERS.

=1NE JAMAIS PRENDRE EN MAIN UN R¢:CIPIENT

ENFLAMMI 2 - vous risquez de vous brOler.

=1NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brOlante.

=1Utiliser un extincteur SEULEMENT si :

- II s'agit d'un extincteur de classe ABC, dont on connaft le

fonctionnement.

- II s'agit d'un petit feu encore limit6 & I'endroit oQ il s'est

d6clar6.

- Les pompiers ont 6t6 contact6s.

- II est possible de garder le dos orient6 vers une sortie

pendant I'op6ration de lutte contre le feu.

aRecommandations tir6es des conseils de s6curit6 en cas

d'incendie de cuisine publi6s par la NFPA.

m AVERTISSEMENT : Pour r6duire le risque d'incendie

ou de choc 61ectrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de r6glage de la vitesse & semi-

conducteurs.

LIRE ET CONSERVER CES INSTRUCTIONS

EXIGENCESD'INSTALLATION

Rassembler les outils et pieces n6cessa_res avant d'entre prendre

I'installation. Lire et observer les instructions fournies avec

chaoun des outils de a liste ci-dessous.

Outils n6cessaires

C saille de ferblantier _1_ Pince & d6nuder

Pistolet a_calfeutrage et compos6 _ _ - -_

de calfeutrage r6sistant aux _ I

intemp6ries _

Pi_ces fournies

Retirer les pieces de I'emballage. Verifier que toutes les pieces

sont presentes.

Vis _t6te plate _

(4 2 x 25 mm) _ _

ChevilleS _ B[ideSde _

Clape t ant!-reflux rectangulair e de

31/4'X 10" (83X254om) / _

Pi_ces n6cessaires

-cannecteurs _ _T S_rro-o_,o de W' _ Lampe & ('_

[ de illS _ I(_3 ram) h0mologu6 ._'_ lincandes: _, / I

cence de

h°m0!0gu6 s UL/CSA i2ov [

75wattsmaxirnum [

! I_cu!°_E26 !

Pour installations avec 6vacuation a I'ext6rieur et conduits

rectangulaires de 3V4"x 10" (8,3 x 25,4 cm)

Circuit d!evacuation m6tallique

rectangulaire de 3 V4

(8,3 x25,4 cm)avec bouche [

de d6charge & travers lernur

ou a travers le toit

Accessoires en option

d'alir

W10355452!

*Pour des renseignements sur la commande, voir la section

"Assistance ou service".

d empksc®m® ,s

IMPORTANT • Observer les dispositions de tous les codes et

r_glements en vigueur.

• C'est & I'installateur qu'incombe la responsabilite de

respecter les distances de separation specifiees sur la plaque

signaletique. La plaque signaletique est situ6e & I'interieur de

la hotte, sur la paroi de gauche.

• Installer la hotte de cuisiniere & distance de toute zone

exposee & des courants d'air, comme fen6tres, portes et

bouches de chauffage & fort debit.

• Respecter les dimensions indiqu6es pour les ouvertures &

decouper dans les meubles. Ces dimensions tiennent

compte des valeurs minimales des degagements de

separation. Avant d'effectuer des decoupages, consulter les

instructions d'installation fournies par le fabricant de la table

de cuisson/cuisiniere.

• II est recommande d'utiliser cette hotte avec une table de

cuisson dont la puissance totale ne depasse pas 40 000 BTU.

• Une prise de courant electrique reliee & la terre est

necessaire. Voir la section "Specifications electriques".

• Assurer I'etancheite au niveau de chaque ouverture

decoupee dans le plafond ou lemur pour I'installation de la

hotte de cuisiniere.

Ces hottes de cuisiniere ont 6te configurees fl I'usine pour

une installation avec decharge & I'exterieur. Les modeles

pouvant 6tre installes dans une configuration sans decharge

&I'exterieur (recyclage) necessitent des filtres & charbon. Voir

la section "Assistance ou service" pour connaitre le

processus de commande des filtres & charbon.

Installation dans une r_sidence mobile

L'installation de cette hotte doit satisfaire aux exigences de la

norme Manufactured Home Construction Safety Standards, Titre

24 CFR, partie 328 (anciennement Federal Standard for Mobile

Home Construction and Safety, titre 24, HUD, partie 280); Iorsque

cette norme n'est pas applicable, I'installation doit satisfaire aux

criteres de la plus recente edition de la norme Manufactured

Home Installation 1982 (Manufactured Home Sites, Communities

and Setups)ANSI A225.1/NFPA 501A, ou des codes et

r_glements Iocaux.

Dimensions du produit

2" -"/_ 69/16'' (16,7cm)

4.15/16"

(12,5 cm)

1 "

(2,5 crn)

18%"

cm)

Distances de d_gagement & respecter

A. 24" (61,0 cm) de distance minimale 4 partir de la surface de

cuisson #lectrique.

24" (61,0 cm) de distance minimale 4 partir de la surface de

cuisson au gaz.

30" (76,2 cm) de distance maximale sugg#r#e au-dessus de la

surface de cuisson.

B. 18" (45,7 cm) de d#gagement minimal entre le placard sup#rieur

et le plan de travail

C. 30" (76,2 cm) de largeur minimale d'ouverture du placard.

D. 12" (30,5 cm) de profondeur de placard.

E.36" (91,4 cm) de hauteur du placard du bas.

M_thodes d'_vacuation

REMARQUES :

• L'emploi d'un conduit flexible est deconseill6. Un conduit

flexible peut causer une retro-pression et des turbulences de

I'air, ce qui reduit considerablement la performance.

• Le circuit d'evacuation est facultatif pour ce modele.

La sortie a I'exterieur du circuit d'evacuation peut se faire

travers le toit ou & travers un mur. Utiliser un conduit

rectangulaire de 31/4'' x 10" (8,3 cm x 25,4 cm) pour un circuit

d'une Iongueur maximale de 35 pi (10,7 m).

levacuation par le dessus levacuation par le mur

A. Conduit rectangulaire de 3 ¼"

x 10" (8,3 x 25,4 cm) avec

#vacuation 4 travers le toit (a

acheter s#par#ment).

B. Bouche de d#charge sur toit

avec clapet

(a acheter s#par#ment)

A. Conduit rectangulaire de 3 ¼"

x 10" (8,3 x 25,4 cm) avec

#vacuation 4 travers lemur ou

le toit (a acheter s#par#ment).

B. Bouche de d#charge 4 travers

le mur avec clapet

(a acheter s#par#ment)

Installations dans les r_gions au climat froid

On doit installer un clapet anti-retour supplementaire a I'arriere

pour minimiser le reflux d'air froid et incorporer un el6ment

d'isolation thermique pour minimiser la conduction de chaleur

par I'intermediaire du conduit d'evacuation, de I'interieur de la

maison & I'exterieur. Le clapet anti-retour doit etre place du c6te

air froid de la resistance thermique.

Uelement d'isolation thermique doit etre aussi proche que

possible de I'endroit o_ le circuit d'evacuation s'introduit dans la

partie chauffee de la maison.

Air d'appoint

Les codes Iocaux en b&timent peuvent imposer I'emploi d'un

circuit de renouvellement de I'air/introduction d'air d'appoint, Iors

de I'utilisation d'un circuit d'aspiration de debit superieur & une

valeur specifiee en pieds cubes par minute. Le debit specific en

pieds cubes par minute varie d'une juridiction & I'autre. Consulter

un professionnel des installations de chauffage ventilation/

climatisation au sujet des exigences specifiques applicables

dans la juridiction locale.

Exigences concernant I'_vacuation

• Le circuit doit decharger I'air 9.I'exterieur.

• Ne pas terminer le circuit d'evacuation dans un grenier ou

dans un autre espace clos.

• Ne pas utiliser une bouche de decharge murale de 4"

(10,2 cm) normalement utilisee pour un equipement de

buanderie.

• Utiliser un conduit metallique rectangulaire de 31/4'' x 10"

(8,3 x 25,4 cm), en fonction de la configuration d'installation.

Un conduit en metal rigide est recommand& Ne pas utiliser

de conduit de plastique ou en aluminium.

• La Iongueur du circuit d'evacuation et le nombre de coudes

doivent _tre reduits au minimum pour des performances

optimales.

Pour un fonctionnement efficace et silencieux •

• Ne pas utiliser plus de trois coudes 9.90°.

• Veiller 9.ce qu'il y ait une section droite de conduit d'un

minimum de 24" (61 cm) entre les coudes si I'on doit utiliser

plus d'un coude.

• Ne pas installer 2 coudes successifs.

• Utiliser des brides ou du ruban adhesif pour conduit pour

assurer I'etanch6it6 de chaque jointure du circuit

d'evacuation.

• Le circuit d'evacuation doit comporter un clapet anti-reflux. Si

la bouche de decharge murale ou par le toit comporte un

clapet, ne pas utiliser le clapet fourni avec la hotte de

cuisiniere.

• A I'aide d'un produit de calfeutrage, assurer I'etancheite

autour de la bouche de decharge 9.I'exterieur (9.travers le

mur ou le toit).

Calcul de la Iongueur du circuit d'_vacuation

Pour calculer la Iongueur effective du circuit d'evacuation

necessaire, additionner les Iongueurs equivalentes (en pieds ou

metres) de tous les composants utilises dans le circuit.

Circuit d'_vacuation

Composant

Coude 9.90 ° 5,0 pi

(1,5 m)

Coude plat de 31/4'' x 12 pi

10" (8,3 cm x 25,4 cm) (3,7 m)

Bouche de decharge 0 pi

murale de 7" (17,8 cm) (0 m)

31/4"x 10" (8,3 cm x 4,5 pi

25,4 cm) 9.7" (17,8 cm) (1,4 m)

Coude 9.90 ° de 31/4"x 5,0 pi

10" (8,3 cm x 25,4 cm) 9. (1,5 m)

7" (17,8 cm)

Exemple de circuit d'_vacuation

Coude a 90 °

1 coude 9.90°

Bouche de

d_charge

murale

6pi(1,Bm) I n

r-ii

2 pi(0,6m)

= 5,0 pi (1,5 m)

1 bouche de decharge murale

Section droite de 8 pi (2,4 m)

Longueur totale

Longueur maximale recommand_e

Circuit d'evacuation rectangulaire

de 31/4"x 10" (8,3 x 25,4 cm)

= 0 pi (0 m)

= 8 pi (2,4 m)

= 13 pi (3,9 m)

= 35 pi (10,7 m)

Observer les dispositions de tousles codes et reglements en

vigueur.

S'assurer que I'installation electrique est correcte et qu'elle

satisfait aux exigences de la plus recente edition de la norme

National Electrical Code, ANSI/NFPA 70, ou de la norme CSA

C22.1-94, Code canadien de I'electricite, partie 1 et C22.2 n°

0-M91 (derniere edition) et de tousles codes et reglements en

vigueur.

Si les codes le permettent et si I'on utilise un conducteur distinct

de liaison 9.la terre, il est recommande qu'un electricien qualifie

verifie la qualite de la liaison 9.la terre.

Pour obtenir un exemplaire des normes des codes ci-dessus,

contacter :

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

L'appareil doit _tre alimente par un circuit de 120 V, CA

seulement, 60 Hz, 15 amperes, protege par fusible.

Si le domicile possede un c&blage en aluminium, suivre la

procedure ci-dessous :

Raccorder une section de c&ble en cuivre massif aux

conducteurs en queue de cochon.

Connecter le c&blage en aluminium 9.la section ajoutee

de c&blage en cuivre en utilisant des connecteurs et/ou

des outils specialement con£sus et homologues UL pour

fixer le cuivre 9.I'aluminium.

Suivre la procedure recommandee par le fabricant de

connecteurs electriques. Les raccordements aluminium/

cuivre doivent satisfaire aux prescriptions des codes Iocaux

et de I'industrie, et _tre conformes aux pratiques de c&blage

reconnues.

Le calibre des conducteurs et les connexions doivent _tre

compatibles avec les caracteristiques electriques de

I'appareil specifiees sur la plaque signaletique. La plaque

signaletique de I'appareil est situee derriere le filtre, sur la

paroi arriere de la hotte.

Le calibre des conducteurs doit _tre conforme aux exigences

du National Electrical Code, de la plus recente edition de la

norme ANSI/NFPA 70 ou des normes CSA C22.1-94, Code

canadien de I'electricite, partie 1 et C22.2 n° 0-M91 (edition la

plus recente) et de tous les codes et reglements en vigueur.

INSTRUCTIONSD'INSTALLATION

REMARQUES :

• Selon le modele, determiner la methode d'evacuation &

utiliser : & travers le toit ou & travers lemur.

II est recommande que I'installation du circuit d'evacuation

soit realis6e avant celle de la hotte. Voir "Circuit

d'evacuation" dans la section "Exigences d'installation" en

cas de besoin.

• Avant d'executer les decoupages, verifier qu'il existe un

degagement suffisant dans le plafond ou lemur pour le

conduit d'evacuation.

1. D6connecter la source de courant

61ectrique

Risque de choc 61ectrique

D_connecter la source de courant 61ectrique avant

I'entretien.

Replacer pi_ces et panneaux avant de faire la remise

en marche.

Le non-respect de ces instructions peut causer

un d_c_s ou un choc 61ectrique.

2. Marquage de I'emplacement des

trous

3. Installation des brides

• A I'aide d'un tournevis Phillips n° 2, installer les chevilles

d'ancrage.

• A I'aide des vis & t_te plate n° 8-18 x 1" (4,2 x 25 mm) Phillips

n° 2 installer les brides de montage en utilisant les trous

superieurs.

REMARQUE : Pour les installations sur une surface autre

qu'un panneau de gypse, il est recommande de faire appel &

du personnel qualifie pour determiner la methode d'ancrage.

4. Pr6paration de la hotte

Aligner le bord exterieur des brides de montage avec les bords

exterieurs du placard superieur.

IMPORTANT : Les brides de montage doivent _tre en contact

avec le placard superieur.

Marquer les trous superieurs des brides avec un crayon.

Placer la hotte en appui sur la face arriere, sur une surface

couverte.

A I'aide d'un tournevis Phillips n° 2, retirer le clapet

rectangulaire attache avec des vis de 3,5 x 9,5 mm.

A I'aide d'un tournevis Phillips n° 2, retirer le couvercle du

boitier de raccordement.

A I'aide d'un tournevis & lame plate, retirer I'opercule pour le

passage de I'alimentation electrique appropn&

5. Marquage de I'emplacement des

trous

6. Marquage et d6coupage de

I'ouverture d'6vacuation

Circuit d'_vacuation pour conduit rectangulaire de

31/4'' x 10" (8,3 x 25,4 cm)

Soulever la hotte et la mettre en place, et inserer les pattes des

brides de montage dans les fentes situ6es a I'arriere de la hotte.

• /_,I'aide d'un foret de 1/2"(13 mm), percer un trou & chaque

marque effectuee prec6demment sur la paroi ou le placard

superieur. En utilisant les extremit6s externes des trous,

marquer I'ouverture de I'evacuation.

• Utiliser une scie sauteuse ou une scie a guichet pour

decouper I'ouverture d'evacuation.

7. Pergage des ouvertures des c6bles

61ectriques

Maintenir la hotte en place d'une main ferme et plier chaque

patte de montage (A)vers le haut en formant un angle d'environ

90°.

Marquer le trou a I'emplacement de I'opercule pour le passage

de I'alimentation electrique (B).

Pour une installation a _vacuation par le dessus : Marquer

I'emplacement des 4 trous d'evacuation (C) sur la partie

superieure de la hotte.

Pour une installation a _vacuation par I'arri_re : Marquer

I'emplacement des 4 trous d'evacuation (D) sur la partie arriere

de la hotte.

FACULTATIF • Marquer le trou de chaque patte de montage.

Retirer la hotte et la mettre de c6te.

/_,I'aide d'un foret de 11/4"(3 cm), percer le trou & I'emplacement

du serre-c&ble marqu6 prec6demment.

FACULTATIF •/_,I'aide d'un foret de 1/8"(3 mm), percer des avant-

trous aux emplacements de chaque patte de montage marqu6s

prec6demment, & un angle d'environ 45 ° vers le haut.

La page charge ...

Whirlpool UXT3030ADB0 Le manuel du propriétaire

Marque: Whirlpool

Modèle: UXT3030ADB0

Catégorie: Hottes

Taper: Le manuel du propriétaire

Ce manuel convient également à

UXT3030ADW0

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool UXT3030ADB0 Owner's manual

Documents connexes

Autres documents

IKEA IH3402YS0 Le manuel du propriétaire