Simplicity MANUAL, OPERATOR'S Manuel utilisateur

Marque: Simplicity

Modèle: MANUAL, OPERATOR'S

Catégorie: Accessoires pour véhicules automobiles

Taper: Manuel utilisateur

Ce manuel convient également à

MANUAL,, OPERATOR'S

61E400, 61G400

Operator's Manual

Manual del operador

Manuel d'utilisation

Revision A

Not for

Reproduction

2 vanguardpower.com

Not for

Reproduction

Not for

Reproduction

General Information

This manual contains the safety information about the hazards and risksrelatedto

the engine and how to prevent them.It also containsthe correctoperation and

maintenance of this engine.It is important that you read, understand, and obey these

instructions. Keepthis manual for future reference.

NOTE:The figures and illustrations in this manual are for information only and can be

different from your model. Use the figures thatalign withyour engine configuration. If it is

necessary, speak to an Authorized Service Dealer.

Record the date of purchase, engine model, type, trim, and the engine serial number

for replacement parts. These numbers are on your engine. Refer to the Features and

Controls section.

Date of Purchase

Engine Model - Type - Trim

Engine Serial Number

European Office Contact Information

For questions related to European emissions, contact our European office at:

Max-Born-Straße 2, 68519 Viernheim, Germany.

European Union (EU) Stage V (5): Carbon

Dioxide (CO2) Values

Enter CO2 in the search window on BriggsandStratton.com to find carbon dioxide values

of Briggs & Stratton EU Type-Approval Certificate engines.

Recycling Information

Recycle all cartons, boxes, used oil, and batteries as

specified by government regulations.

Operator Safety

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information about hazards that could

result in personal injury. A signal word (DANGER, WARNING, or CAUTION) is used to

indicate the likelihood and the potential severity of injury. In addition, a hazard symbol

is used to represent the type of hazard.

DANGER indicates a hazard which, if not avoided, will result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could result in death or serious

injury.

CAUTION indicates a hazard which, if not avoided, could result in minor or moderate

injury.

NOTICE indicates information considered important but not hazard-related.

Hazard Symbols and Meanings

Safety information about

hazards that can result in

personal injury.

Read and understand the

Operator's Manual before

operating or servicing the

unit.

Fire Hazard Explosion Hazard

Shock Hazard Toxic Fume Hazard

Hot Surface Hazard Kickback Hazard

Amputation Hazard -

Moving Parts

Fuel Level - Maximum

Do Not Overfill

Safety Messages

WARNING

This product can expose you to chemicals including gasoline engine exhaust, which is

known to the State of California to cause cancer, and carbon monoxide, which is known

to the State of California to cause birth defects or other reproductive harm. For more

information go towww.P65Warnings.ca.gov.

WARNING

Briggs & Stratton® Engines are not designed for and are not to be used to power:

fun-karts; go-karts; children's, recreational, or sport all-terrain vehicles (ATVs);

motorbikes; hovercraft; aircraft products; or vehicles used in competitive events not

sanctioned by Briggs & Stratton. For information about competitive racing products, see

www.briggsracing.com. For use with utility and side-by-side ATVs, please contact Briggs

& Stratton Power Application Center, 1-866-927-3349. Incorrect engine use could result

in serious injury or death.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

When you operate the equipment

• Do not tilt the engine or the equipment at an angle which causes fuel to spill.

• Do not choke the carburetor (if equipped) to stop the engine.

• Do not start or operate the engine with the air cleaner (if equipped) or the air

filter (if equipped) removed.

When you do maintenance

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occurand could result a fire or an explosion.

• During maintenance if it is necessary to tilt the unit, make sure that the fuel tank,

if mounted on the engine, is empty and that the spark plug side is up. If the fuel

tank is not empty, leakage can occurand could result a fire or an explosion.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• Do not change the governor spring, links or other parts to increase engine

speed.

• Do not hit the flywheel with a hammer or hard object. This could result in failure

of the flywheel during operation.

• Replacement parts must be of the same design and installed in the same

position as the original parts. Other parts could result in damage or an injury.

When you move the location of equipment

• Make sure that the fuel tank is EMPTY or that the fuel shut-off valve is in the

CLOSED position.

4 vanguardpower.com

Not for

Reproduction

When fuel or equipment is in storage with fuel in the fuel tank

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that

have pilot lights.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Engine start-up causes spark that could result in a fire or explosion.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and windows

for ventilation. After the operation of this product, carbon monoxide can quickly

collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

WARNING

Fast retraction of the starter cord (kickback) will pull your hand and arm to the

engine faster than you can let go.Broken bones, fractures, bruises or sprains

could result.

• To prevent kickback when you start the engine, pull the starter cord slowly until

resistance is felt and then pull quickly.

• Before you start the engine, disconnect or remove all external equipment and

engine loads.

• Make sure that direct-coupled equipment components, such as, but not limited

to, blades, impellers, pulleys, and sprockets, are correctly attached.

WARNING

Rotating parts can entangle hands, feet, hair, clothing, or accessories and result

in traumatic amputation or laceration.

• Operate equipment with the guards correctly installed.

• Keep hands and feet away from rotating parts.

• Remove jewelry and make sure that long hair is away from all rotating parts.

• Do not wear loose clothes or items that could become caught.

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

WARNING

Accidental engine spark can cause an electric shock, fire or explosion and could

result in entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect all spark plug wires and keep them away from the spark plugs.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start).

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

If you smell gas

• Do not start the engine.

• Do not switch on electrical switches.

• Do not use a phone in the vicinity.

• Evacuate the area.

• Contact the gas supplier or the fire department.

Features and Controls

Engine Controls

Compare the callout letters in Figures 1 and 2 to the engine controls in the list that

follows:

A. Engine Identification Numbers Model - Type - Code

B. Spark Plug

C. Air Cleaner, Low Profile

D. Dipstick

E. Oil Fill

F. Oil Filter

G. Oil Drain Plug

H. Oil Pressure Sensor

I. Air Intake Grille

J. Electric Starter

K. Starter Solenoid

L. Regulator / Rectifier

M. Oil Cooler (if equipped)

N. Muffler (if equipped)

O. Fuel Pump

P. Starter Switch1

Q. Fuel Filter (if equipped)

Some engines and equipment have remote controls. See the equipment manual for the

location and operation of remote controls.

Engine Control Symbols and Meanings

Engine Speed - FAST Engine Speed - SLOW

Engine Speed - STOP ON - OFF

Engine Start

Choke CLOSED

Engine Start

Choke OPEN

Not for

Reproduction

Fuel Cap

Fuel Shut-off OPEN

Fuel Shut-off CLOSED

Operation

Oil Recommendations

Oil Capacity: Refer to the Specifications section.

We recommend the use of Briggs & Stratton® Warranty Certified oils for best

performance. Other high-quality detergent oils are permitted if classified for service SF,

SG, SH, SJ or higher. Do not use special additives.

Use the chart to select the best viscosity for the outdoor temperature range expected.

Engines on most outdoor power equipment operategoodwith 5W-30 Synthetic oil. For

equipment operated in hot temperatures, Vanguard® 15W-50 Synthetic oil gives the best

protection.

A SAE 30 - Below 40 °F (4 °C) the use of SAE 30 will result in hard starting.

B 10W-30 - Above 80 °F (27 °C) the use of 10W-30 may cause increased oil

consumption. Checkthe oil level frequently.

C 5W-30

D Synthetic 5W-30

EVanguard® Synthetic 15W-50

Check the Oil Level

Before you check or add oil

• Make sure the engine is level.

• Clean the oil fill area of debris.

• Refer to the Specifications section for oil capacity.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

1. Remove the dipstick (A, Figure 3) and clean with a cloth.

2. Install and tighten the dipstick (A, Figure 3).

3. Remove the dipstick and check the oil level. Make sure that the oil level is at the

top of the full indicator (B, Figure 3) on the dipstick.

4. If the oil level is low, slowly add oil into the engine oil fill (C, Figure 3). Do not add

too much oil.

5. Wait one minute and check the oil level again. Make sure that the oil level is

correct.

6. Install and tighten the dipstick (A, Figure 3).

Low Oil Protection System (if installed)

A low oil sensor is installed on some engines. If the oil is low, the sensor will show a

warning light or stop the engine. Stop the engine and do the steps that follow before you

start the engine.

• Make sure that the engine is level.

• Do an oil check. Refer to the Check Oil Level section.

• If the oil level is low, add the correct amount of oil. Start the engine and make

sure that the warning light (if installed) does not come on.

• If the oil level is not low, do not start the engine. Contact a Briggs & Stratton

Authorized Service Dealer to correct the oil problem.

Fuel Recommendations

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High altitude use, see below.

• Gasoline with up to 10% ethanol (gasohol) is permitted.

NOTICE

Do not use unapproved gasoline, such as E15 and E85. Do not mix oil in gasoline or

change the engine to operate on alternate fuels. Use of unapproved fuels could result in

damage to engine components, which will not be repaired under the warranty.

To protect the fuel system from gum formation, and corrosion, mix analcohol-free fuel

stabilizer and ethanol treatmentinto the fuel. Refer to the Storage section. All fuel is not

the same. If start or performance problems occur, change fuel providers or brands. This

engine is certified to operate on gasoline. The emissions control system for carbureted

engines is EM (Engine Modifications). The emissions control systems for engines with

electronic fuel injection are ECM (Engine Control Module), MFI (Multiport Fuel Injection),

TBI (Throttle Body Fuel Injection) and if equipped an O2S (Oxygen Sensor).

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum 85 octane/85 AKI (89 RON)

gasoline is permitted.

For carbureted engines, high altitude adjustment is required to maintain performance.

Operation without this adjustment will cause decreased performance, increased fuel

consumption, and increased emissions. Contact a Briggs & Stratton Authorized Service

Dealer for high altitude adjustment information. Operation of the engine at altitudes

below 2,500 feet (762 meters) with the high altitude adjustment is not recommended.

For Electronic Fuel Injection (EFI) engines, no high altitude adjustment is necessary.

Add Fuel

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you add fuel

• Stop the engine. Before you remove the fuel cap, wait a minimum of two (2)

minutes to make sure that the engine is cool.

• Fill the fuel tank outdoors or in an area that has good airflow.

• Do not put too much fuel in the tank. For expansion of the fuel, do not fill above

the bottom of the fuel tank neck.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

1. Clean the fuel cap area of dirt and debris. Remove the fuel cap.

2. Fill the fuel tank (A, Figure 4) with fuel. Because fuel will expand, do not fill above

the bottom of the fuel tank neck (B).

3. Install the fuel cap.

Start the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

When you start the engine

• Make sure that the spark plug, muffler, fuel cap and air cleaner (if equipped) are

correctly installed.

• Do not crank the engine with the spark plug removed.

• If the engine is flooded, set the choke (if equipped) to the OPEN or RUN

position. Move the throttle (if equipped) to the FAST position and crank until the

engine starts.

• If there is natural or LP gas leakage in the area, do not start the engine.

• Because vapors are flammable, do not use pressurized starter fluids.

6 vanguardpower.com

Not for

Reproduction

WARNING

POISONOUS GAS HAZARD. Engine exhaust contains carbon monoxide, a

poisonous gas that could kill you in minutes. Although you do not smell exhaust

fumes, you could still be exposed to dangerous carbon monoxide gas. If you feel

sick, dizzy, or weak while you use this product, get to fresh air RIGHT AWAY. See

a doctor. You may have carbon monoxide poisoning.

• Carbon monoxide gas can collect in occupied spaces. To reduce the risk of

carbon monoxide gas, ONLY operate this product outdoors and far away from

windows, doors and vents.

• Install battery-operated carbon monoxide alarms or plug-in carbon monoxide

alarms with battery back-up as specified by the manufacturer's instructions.

Smoke alarms cannot sense carbon monoxide gas.

• DO NOT operate this product in homes, garages, basements, crawlspaces,

sheds, or other closed spaces, even if you use fans or open doors and windows

for ventilation. After the operation of this product, carbon monoxide can quickly

collect in these spaces and stay for hours.

• ALWAYS put this product downwind and point the engine exhaust away from

occupied spaces.

NOTICE

This engine was shipped from Briggs & Stratton without oil. Equipment manufacturers or

dealers could have added oil to the engine. Before you start the engine for the first time,

make sure that the oil is at the correct level. Add oil as specified by the instructions in

this manual. If you start the engine without oil, damage will occur and the engine will not

be repaired under warranty.

NOTE:Your equipment could have remote controls. Refer to the equipment manual for

location and operation of remote controls

For information on how to start the engine, read the operation instructions supplied by

the equipment manufacturer.

Electronic Fuel Injection (EFI) System

1. Check the engine oil. See the Check the Oil Level section.

2. Make sure that the equipment drive controls, if installed, are disengaged.

3. Move the fuel shut-off (A, Figure 5), if installed, to the OPEN position.

4. Move the throttle controlto the SLOW position.

5. Push the stop switch (D, Figure 5), if installed, to the ON position.

6. Turn the electric start switch (E, Figure 5) to the ON or START position.

NOTICETo extend the life of the starter, use short start cycles (five seconds maximum).

Wait one minute between start cycles.

If the engine does not start after 3or 4 times, contact your local dealer or goto

vanguardpower.com or call 1-800-999-9333.

Stop the Engine

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Do not choke the carburetor (if equipped) to stop the engine.

1. Stop Switch, if installed: Move the stop switch (D, Figure 6) to the OFF position.

2. Key Switch, if installed: Set the throttle control to the SLOW position. Turn the

key switch (E, Figure 6) to the OFF position. Remove the key and keep it in a safe

location out ofreach of children.

3. After the engine stops, move the fuel shut-off (A, Figure 6), if installed, to the

CLOSED position.

Maintenance

Maintenance Information

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Duringmaintenanceif it is necessary to tilt the unit, make sure that the fuel tank, if

mounted on the engine, is empty and that the spark plug side is up. If the fuel tank is not

empty, leakage can occur and could result in a fire or an explosion. If the engine is tilted

in a different direction, it will not easily start because of oil or fuel contamination of the air

filter or the spark plug.

WARNING

Accidental engine spark can cause an electric shock, fire or explosion and could

result in entanglement, traumatic amputation or laceration.

Before you make adjustments or repairs:

• Disconnect all spark plug wires and keep them away from the spark plugs.

• Disconnect the battery wire from the negative battery terminal (only engines with

electric start).

• Use only the correct tools.

When you check for spark:

• Use an approved spark plug tester.

• Do not check for spark with the spark plug removed.

WARNING

Replacement parts must be of the same design and installed in the same position as the

original parts. Other parts could result in damage or an injury.

NOTICE

All the components used to build this engine must remain in place for correct operation.

See a Briggs & Stratton Authorized Service Dealer for all maintenance and servicing of

the engine and engine parts.

Emissions Control Service

For maintenance, replacement, or repair of emissions control devices and

systems, contact a qualified off-road engine repair establishment or service

technician. However, for "no charge" emissions control service, the work must be done

by a factory authorized dealer. Refer to the Emissions Control Statements.

Maintenance Schedule

Intervals of 8 Hours or Daily

• Check the engine oil level.

• Clean the area around the muffler and controls.

Intervals of 100 Hours or Annually

• Replace the spark plugs.

• Change the engine oil.

• Replace the oil filter (ifinstalled).

•Service the air filter 1.

•Clean the pre-cleaner (if installed)1 .

• Service the exhaust system.

Intervals of 250 Hours or Annually

• Check the valve clearance. Adjust if necessary.

Intervals of 400 Hours or Annually

• Replacethe air filter.

• Replace the fuel filter.

•Service the air cooling system1.

•Clean the oil cooler fins1.

1 Clean more frequently in dusty conditions or when many particles are in the air.

Electronic Fuel Injection (EFI) System

The EFI System monitors engine temperature, engine speed, and battery voltage for

engine start-up and warm-up. There are no adjustments on the system. If start-up or

operation problems occur, contact a Briggs & Stratton Authorized Service Dealer.

NOTICEMake sure to obey the steps that follow or damage to the EFI system could

occur.

• DO NOT start the engine if the battery cables are loose.

• Turn the key to the OFF position before you disconnect, remove, and / or install

the battery.

• DO NOT use a battery charger to start the engine.

• DO NOT disconnect the battery cables during engine operation.

• When you disconnect the battery cables, first connect the positive (+) cable, and

then connect the negative (-) cable to the battery.

• When you charge the battery, turn the ignition switch to the OFF position,and

disconnect the negative (-) battery cable from the battery.

Not for

Reproduction

• DO NOT spray water directly on the Electronic Control Module.

Servicing the Spark Plug

Check the spark plug gap (A, Figure 7) with a wire gauge (B). If necessary, set the

spark plug gap. Install and tighten the spark plug to the correct torque. For gapand

torque specifications, refer to the Specifications section.

Servicing theExhaust System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible materials, such as leaves, grass and brush, can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

It is a violation of California Public Resource Code, Section 4442, to use or operate the

engine on any forest-covered, brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in section 4442, maintained in

effective working order. Other states or federal jurisdictions may have similar laws;

reference Federal Regulation 36 CFR Part 261.52. Contact the original equipment

manufacturer, retailer, or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Remove debris from the muffler and cylinder area. Inspect the muffler for cracks,

corrosion, or other damage. Remove the deflector or the spark arrester, if equipped, and

inspect for damage or carbon blockage. If damage is found, install the replacement parts

before you operate the equipment.

Change Engine Oil

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

• If you drain the oil from the top oil fill tube, the fuel tank must be empty. If it is not

empty, fuel leakage can occur and cause a fire or an explosion.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

Used oil is a hazardous waste product and must be discarded of correctly. Do not

discard with household waste. Contact your local authorities, service center, or dealer

for safe disposal or recycling facilities.

Remove Oil

1. With engine OFF but warm, disconnect the spark plug wire(s)(D, Figure 8), and

keep it away from the spark plug(s)(E).

2. Remove the dipstick (A, Figure 9).

3. Remove the oil drain plug (F, Figure 10). Drain the oil into an approved container.

4. Install and tighten the oil drain plug(F, Figure 10).

Change the Oil Filter

1. Drain the oil from the engine. Refer to the Remove Oil section.

2. Remove the oil filter (H, Figure 11) anddiscard correctly.

3. Before you install the new oil filter, lightly lubricate the oil filter gasket withclean oil.

4. Install the oil filter by hand until the gaskettouchesthe oil filter adapter, then tighten

the oil filter 1/2 to 3/4 turns.

5. Add oil. Refer to the Add Oil section.

6. Start and operatethe engine. When the engine is warm, do a checkfor oil leaks.

7. Stop the engine. Make sure thatoil level is at the top of the full indicatoron the

dipstick. Refer to the Add Oil section.

Add Oil

• Make sure the engine is level.

• Clean the oil fill area of all debris.

• Refer to the Specifications section for oil capacity.

1. Remove the dipstick (A, Figure 9). Remove oil from the dipstick with a clean cloth.

2. Slowly add oil into the engine oil fill (C, Figure 9). Do not overfill. Wait one minute

and then check the oil level.

3. Install and tighten the dipstick (A, Figure 9).

4. Remove the dipstick and check the oil level. The correct oil level is at the top of the

full indicator (B, Figure 9) on the dipstick.

5. Install and tighten the dipstick (A, Figure 9).

6. Connect the spark plug wire(s) (D, Figure 8) to the spark plug(s) (E).

Servicingthe Air Filter

WARNING

Fuel vapors are flammable and explosive. Fire or explosion could result in burns

or death.

• Do notstart and operate the engine with the air cleaner assembly (if equipped)

or the air filter (if equipped) removed.

NOTICE

Do not use pressurized air or solvents to clean the filter. Pressurized air could result in

damage to the filter and solvents will dissolve the filter.

See the Maintenance Schedule forservicingrequirements.

Different models will use a foam or a paper filter. Some models could also have an

optional pre-cleaner that can becleanedand used again. Compare the illustrations in

this manual with the type installed on your engine and service as follows.

Low Profile Air Filter

1. Remove the fastener(s) (A, Figure 12).

2. Remove the cover (B, Figure 12).

3. Remove the fastener(s) (C, Figure 12) and retainer (D).

4. Remove the air filter (E, Figure 12).

5. Remove the pre-cleaner (F, Figure 12), if installed, from the air filter (E).

6. To loosenunwanted material, lightly tap the air filter (E, Figure 12) on a hard

surface. If the air filter is dirty, replace with a new air filter.

7. Clean the pre-cleaner (F, Figure 12), if installed, in liquid detergent and water. Make

sure the pre-cleaner is fully dry. Do not lubricate the pre-cleaner.

8. Assemble the dry pre-cleaner (F, Figure 12), if installed, to the air filter (E).

9. Install the air filter (E, Figure 12) with the retainer (D) and fastener(s) (C).

10. Install the cover (B, Figure 12) with the fastener(s) (A). Make sure that the

fastener(s) is tight.

Servicing the Fuel System

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

• Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition

sources.

• Frequently examine the fuel lines, fuel tank, fuel cap, and connections for cracks

or leaks. Replace damaged parts.

• If fuel spills, wait until it dries before you start the engine.

Fuel Filter, if installed

1. Before you replace the fuel filter (A, Figure 13), drain the fuel tank or close the fuel

shut-off valve. If the fuel tank is not drained, fuel leakagecanoccur and cause a fire

or explosion.

2. Squeeze the tabs (B, Figure 13) on the clamps (C) with pliers.Move the clamps

away from the fuel filter (A).

3. Twist and pull the fuel lines (D,Figure 13) off of the fuel filter.

4. Examinethe fuel lines (D, Figure 13) for cracks or leaks. If it is necessary, replace

the fuel lines.

5. Replace the fuel filter (A, Figure 13).

6. Attach the fuel lines (D, Figure 13) with clamps (C).

Servicing the Cooling System

WARNING

During operation, the engine and muffler become hot. If you touch a hot engine,

thermal burns can occur.

Combustible debris, such as leaves, grass, and brush can catch fire.

• Before you touch the engine or muffler, stop the engine and wait two (2)

minutes. Make sure that the engine and muffler are safe to touch.

• Remove debris from the muffler and engine.

8 vanguardpower.com

Not for

Reproduction

NOTICE

Do not use water to clean the engine. Water could cause contamination of the fuel

system. Use a brush or dry cloth to clean the engine.

This is an air cooled engine. Dirt or debris can prevent air flow and cause the engine to

become too hot and result in unsatisfactory performance and decreased engine life.

1. Use a brush or dry cloth to remove debris from the air intake grille.

2. Keep linkage, springs, and controls clean.

3. Keep the area around and behind the muffler, if equipped, free of combustible

debris.

4. Make sure the oil cooler fins, if equipped, are clean.

After a period of time, the cylinder cooling fins can collect debris and cause the engine

to overheat. Thisunwanted materialcannot be removed without partial disassembly of

the engine. Have a Briggs & Stratton Authorized Service Dealer inspect and clean the

air cooling system as recommended in the Maintenance Schedule.

Storage

Fuel System

Refer to Figure: 14.

WARNING

Fuel and its vapors are flammable and explosive. Fire or explosion could result in

burns or death.

Fuel Storage

• Because pilot lights or other ignition sources can cause explosions, keep fuel or

equipment away from furnaces, stoves, water heaters or other appliances that

have pilot lights.

Keep the engine level (normal operating position). Fill the fuel tank (A, Figure 14) with

fuel. For fuel expansion, do not fill above the fuel tank neck (B).

Fuel can become stale when kept in a storage container for more than 30 days.The use

of analcohol-free fuel stabilizer and ethanol treatmentin the fuel storage container is

recommended to prevent fuel degradation and keep the fuel fresh.

When you fill the fuel container with fuel, addan alcohol-free fuel stabilizer as specified

by the manufacturer’s instructions.If gasoline in the engine has not been treated with a

fuel stabilizer, it must be drained into an approved container.Operate the engine until it

is out of fuel.

Engine Oil

While the engine is warm, change the engine oil. Refer to Change the Engine Oil

section.

NOTICEKeep the engine level at the usual operating position. If the engine is tipped in

other directions, it can be difficult to start due to oil contamination to the air filter and/or

the spark plug.

Troubleshooting

Assistance

For assistance, contact your local dealer or go to BRIGGSandSTRATTON.COM or call

1-800-444-7774 (in USA).

Specifications

Specificationsand Service Parts

Models: 61E400, 61G400

Displacement 60.60 ci (993 cc)

Bore 3.366 in ( 85,5 mm)

Stroke 3.406 in (86,5 mm)

Oil Capacity 78 - 80 oz (2,3 - 2,4 L)

Spark Plug Gap 0.030 in (,76 mm)

Spark Plug Torque 180 lb-in (20 Nm)

Intake Valve Clearance .004 - .006 in(,10 - ,15 mm)

Exhaust Valve Clearance .007 - .009 in (,18 - ,23 mm)

Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and

1% for each 10°F (5.6°C) above 77° F (25°C). The engine will operate satisfactorily

at an angle up to 15°. Refer to the equipment Operator's Manual for safe permitted

operating limits on slopes.

Service Parts - Models: 61E400, 61G400

Service Part Part Number

Service Parts - Models: 61E400, 61G400

Air Filter, Low Profile 692519

Pre-cleaner, Low Profile 692520

Oil - SAE 30 100028

Oil Filter 842921

Fuel Filter 845125

Resistor Spark Plug 491055S

Long Life Platinum Spark Plug 5066K

Spark Plug Wrench 19576S

Spark Tester 84003327

We recommend that you see a Briggs & Stratton Authorized Dealer for maintenance

and servicing of the engine and engine parts.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance

with SAE (Society of Automotive Engineers) code J1940 Small Engine Power & Torque

Rating Procedure, and is rated in accordance with SAE J1995. Torque values are

derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM

for all others; horsepower values are derived at 3600 RPM. The gross power curves

can be viewed at www.BRIGGSandSTRATTON.COM. Net power values are taken with

exhaust and air cleaner installed whereas gross power values are collected without

these attachments. Actual gross engine power will be higher than net engine power and

is affected by, among other things, ambient operating conditions and engine-to-engine

variability. Given the wide array of products on which engines are placed, the gasoline

engine may not develop the rated gross power when used in a given piece of power

equipment. This difference is due to a variety of factors including, but not limited to, the

variety of engine components (air cleaner, exhaust, charging, cooling, carburetor, fuel

pump, etc.), application limitations, ambient operating conditions (temperature, humidity,

altitude), and engine-to-engine variability. Due to manufacturing and capacity limitations,

Briggs & Stratton may substitute an engine of higher rated power for this engine.

Warranty

Briggs & Stratton® Engine Warranty

Effective August 2022

Limited Warranty

Briggs & Stratton warrants that, during the warranty period specified below, it will

repair or replace, free of charge, with a new, reconditioned or re-manufactured part,

at the sole discretion of Briggs & Stratton, any part that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or

replacement under this warranty must be borne by purchaser. This warranty is effective

for and is subject to the time periods and conditions stated below. For warranty

service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM. The purchaser must contact the Authorized Service

Dealer, and then make the product available to the Authorized Service Dealer for

inspection and testing.

There is no other express warranty. Implied warranties, including those of

merchantability and fitness for a particular purpose, are limited to one year

from purchase, or to the extent permitted by law. All other implied warranties

are excluded. Liability for incidental or consequential damages are excluded

to the extent exclusion is permitted by law. Some states or countries do not allow

limitations on how long an implied warranty lasts, and some states or countries donot

allow the exclusion or limitation of incidental or consequential damages, so the above

limitation and exclusion may not apply to you. This warranty gives you specific legal

rights and you may also have other rights which vary from state to state and country to

country*.

Standard Warranty Terms 1, 2

Vanguard®; Commercial Series

Consumer Use - 36 months

Commercial Use - 36 months

XR Series

Consumer Use - 24 months

Commercial Use - 24 months

All Other Engines Featuring Dura-Bore™ Cast Iron Sleeve

Consumer Use - 24 months

Commercial Use - 12 months

All Other Engines

Consumer Use - 24 months

Commercial Use - 3 months

Not for

Reproduction

1These are our standard warranty terms, but occasionally there may be additional

warranty coverage that was not determined at time of publication. For a listing of

current warranty terms for your engine, go to BRIGGSandSTRATTON.COM or contact

your Briggs & Stratton Authorized Service Dealer.

2There is no warranty for engines on equipment used for prime power in place of a

utility; standby generators used for commercial purposes, utility vehicles exceeding 25

MPH, or engines used in competitive racing or on commercial or rental tracks.

* In Australia - Our goods come with guarantees that cannot be excluded under the

Australian Consumer Law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of

acceptable quality and the failure does not amount to a major failure. For warranty

service, find the nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM, or by calling 1300 274 447, or by emailing or writing

to [email protected], Briggs & Stratton Australia Pty Ltd, 1

Moorebank Avenue, Moorebank, NSW, Australia, 2170.

The warranty period begins on the date of purchase by the first retail consumer or

commercial end user, and continues for the period of time stated in the table above.

“Consumer use” means personal residential household use by a retail consumer.

“Commercial use” means all other uses, including use for commercial, income

producing or rental purposes. Once an engine has experienced commercial use,

it shall thereafter be considered as a commercial use engine for purposes of this

warranty.

No warranty registration is necessary to obtain warranty on Briggs & Stratton

products. Save your proof of purchase receipt. If you do not provide proof of the

initial purchase date at the time warranty service is requested, the manufacturing

date of the product will be used to determine the warranty period.

About Your Warranty

This limited warranty covers engine-related material and/or workmanship issues only,

and not replacement or refund of the equipment to which the engine may be mounted.

Routine maintenance, tune-ups, adjustments, or normal wear and tear are not covered

under this warranty. Similarly, warranty is not applicable if the engine has been altered

or modified or if the engine serial number has been defaced or removed. This warranty

does not cover engine damage or performance problems caused by:

1. The use of parts that are not original Briggs & Stratton parts;

2. Operating the engine with insufficient, contaminated, or an incorrect grade of

lubricating oil;

3. The use of contaminated or stale fuel, gasoline formulated with ethanol greater

than 10%, or the use of alternative fuels such as liquefied petroleum or natural gas

on engines not originally designed/manufactured by Briggs & Stratton to operate

on such fuels;

4. Dirt which entered the engine because of improper air cleaner maintenance or

reassembly;

5. Striking an object with the cutter blade of a rotary lawn mower, loose or improperly

installed blade adapters, impellers, or other crankshaft coupled devices, or

excessive v-belt tightness;

6. Associated parts or assemblies such as clutches, transmissions, equipment

controls, etc., which are not supplied by Briggs & Stratton;

7. Overheating due to grass clippings, dirt and debris, or rodent nests which plug or

clog the cooling fins or flywheel area, or by operating the engine without sufficient

ventilation;

8. Excessive vibration due to over-speeding, loose engine mounting, loose or

unbalanced cutter blades or impellers, or improper coupling of equipment

components to the crankshaft;

9. Misuse, lack of routine maintenance, shipping, handling, or warehousing of

equipment, or improper engine installation.

Warranty service is available only through Briggs & Stratton Authorized Service

Dealers. Locate your nearest Authorized Service Dealer in our dealer locator map at

BRIGGSandSTRATTON.COM or by calling 1-800-444-7774 (in USA).

80114782(Revision A)

Briggs & Stratton Emissions Warranty

U.S. EPA and Briggs & Stratton, LLC Emissions Control Warranty Statement -

Your Warranty Rights and Obligations

For Briggs & Stratton Marine Engine Models with "J" Trim Designation (Model-

Type-Trim Representation xxxxxx xxxx Jx)

The U.S. EPA, and Briggs & Stratton (B&S) are pleased to explain the exhaust

emissions control system warranty on your Model Year 2022-2024 engine. In the U.S,

new small off-road engines and large spark ignited engines less than or equal to 1.0

liter must be designed, built, and equipped to meet stringent anti-smog standards. B&S

must warrant the emissions control system on your engine for the periods of time listed

below provided there has been no abuse, neglect, or improper maintenance of your

engine leading to the failure of the emissions control system.

Your emissions control system may include parts such as the carburetor or fuel-

injection system, the ignition system, catalytic converter, fuel tanks, fuel lines (for liquid

fuel and fuel vapors), fuel caps, valves, canisters, filters, clamps and other associated

components. Also included may be hoses, belts, connectors, and other emission-

related assemblies.

Where a warrantable condition exists, B&S will repair your engine at no cost to you

including diagnosis, parts, and labor.

Manufacturer’s Warranty Coverage:

The exhaust emissions control system on your marine engine is warranted for five

(5) years or 175 hours, whichever occurs first. If any emissions-related parts on your

engine is defective, the part will be repaired of replaced by B&S.

The exhaust and evaporative

Owner’s Warranty Responsibilities:

• As the engine owner, you are responsible for the performance of the required

maintenance listed in your Operator’s Manual. B&S recommends that you

retain all receipts covering maintenance on your engine, but B&S cannot deny

warranty coverage solely for the lack of receipts or your failure to ensure the

performance of all scheduled maintenance.

• As the engine owner, you should however be aware that B&S may deny you

warranty coverage if your engine or a part has failed due to abuse, neglect,

improper maintenance, or unapproved modifications.

• You are responsible for presenting your engine to a B&S distribution center,

or service center, as soon as a problem exists. The warranty repairs should

be completed in a reasonable amount of time, not to exceed 30 days. If you

have a question regarding your warranty rights and responsibilities, you should

contact B&S at 1-800-444-7774 (in USA) or BRIGGSandSTRATTON.com.

Briggs & Stratton Emissions Control Warranty Provisions

The following are specific provisions relative to your Emissions Control Warranty

Coverage. It is in addition to the B&S engine warranty for non-regulated engines found

in the Operator’s Manual.

1. Warranted Emissions Parts

Coverage under this warranty extends only to the parts listed below (the emissions

control systems parts) to the extent these parts were present on the B&S engine.

a. Fuel Metering System

• Cold start enrichment system (soft choke)

• Carburetor or fuel injection system

• Oxygen sensor

• Electronic control unit

• Fuel pump module

b. Air Induction System

• Air cleaner

• Intake manifold

c. Ignition System

• Spark plug(s)

• Magneto ignition system

d. Catalyst System

• Catalytic converter

• Exhaust manifold

• Air injection system or pulse value

e. Miscellaneous Items Used in Above Systems

• Vacuum, temperature, position, time sensitive valves and switches

• Connectors and assemblies

• Electronic controls

2. Length of Coverage

Coverage is for a period of five (5) years from the date of delivery to an ultimate

purchaser, or 175 hours, whichever occurs first. B&S warrants to the original

purchaser and each subsequent purchaser that the engine is designed, built, and

equipped so as to conform with all applicable regulations under Section 213 of

the Clean Air Act that is free from defects in material and workmanship that could

cause the failure of a warranted part;and that is identical in all material respects

to the engine described in the manufacturer’s application for certification. The

warranty period begins on the date the engine or equipment is delivered to an

ultimate purchaser.

The warranty on emissions-related parts is as follows:

• Any warranted part that is not scheduled for replacement as required

maintenance in the Operator’s Manual supplied, is warranted for the warranty

period stated above. If any such part fails during the period of warranty

coverage, the part will be repaired or replaced by B&S at no charge to

the owner. Any such part repaired or replaced under the warranty will be

warranted for the remaining warranty period.

10 vanguardpower.com

Not for

Reproduction

• Any warranted part that is scheduled only for regular inspection in the

Operator’s Manual supplied, is warranted for the warranty period stated

above. Any such part repaired or replaced under warranty will be warranted

for the remaining warranty period.

• Any warranted part that is scheduled for replacement as required

maintenance in the Operator's Manual supplied, is warranted for the period of

time prior to the first scheduled replacement point for that part. If the part fails

prior to the first scheduled replacement, the part will be repaired or replaced

by B&S at no charge to the owner. Any such part repaired or replaced under

warranty will be warranted for the remainder of the period prior to the first

scheduled replacement point for the part.

• Add-on or modified parts that are not exempted by the U.S. EPA may not be

used. The use of any non-exempted add-on or modified parts by the owner

will be grounds for disallowing a warranty claim. The manufacturer will not

be liable to warrant failures of warranted parts caused by the use of a non-

exempted add-on or modified part.

3. Consequential Coverage

Coverage shall extend to the failure of any engine components caused by the

failure of any warranted emissions parts.

4. Claims and Coverage Exclusions

Warranty claims shall be filed according to the provisions of the B&S engine

warranty policy. Warranty coverage does not apply to failures of emissions

parts that are not original equipment B&S parts or to parts that fail due to abuse,

neglect, or improper maintenance as set forth in the B&S engine warranty policy.

B&S is not liable for warranty coverage of failures of emissions parts caused by

the use of add-on or modified parts.

80111506 (Revision A)

Not for

Reproduction

Información general

Este manual contiene información de seguridad sobre los peligros y riesgos

relacionados con el motor y cómo prevenirlos. También contiene el correcto

funcionamiento y mantenimiento de este motor. Es importante que lea, comprenda y

obedezca estas instrucciones. Conserve este manual para referencia futura.

NOTA:Las figuras e ilustraciones en este manual sirven solo para información y

pueden ser diferentes a su modelo. Utilice las cifras que se alinean con la configuración

de su motor. Si es necesario, hable con un distribuidor de servicio autorizado.

Registre la fecha de compra, el modelo del motor, el tipo, la versión y el número

de serie del motor para las piezas de repuesto. Estos números están en su motor.

Consulte la secciónCaracterísticas y controles.

Fecha de compra

Modelo del motor - Tipo - Reglaje

Número de Serie del motor

Información de contacto de la oficina en

Europa

Si tiene preguntas relacionadas con las emisiones europeas, póngase en contacto con

nuestra oficina en Europa en:

Max-Born-Straße2, 68519 Viernheim, Alemania.

EtapaV (5) de la Unión Europea (UE):

Valores del dióxido de carbono (CO2)

Ingrese CO2 en la ventana de búsqueda en BriggsandStratton.com. para encontrar los

valores de dióxido de carbono de los motores de Briggs & Stratton con certificado de

aprobación tipo UE.

Información de reciclaje

Recicle todos los cartones, cajas, aceite usado y baterías

según lo especifiquen las regulaciones gubernamentales.

Seguridad del operador

Símbolo de alerta de seguridad y palabras de

señalización

El símbolo de alerta de seguridad identifica información de seguridad

sobre peligros que podrían provocar lesiones personales. Se usa una palabra

de señalización (PELIGRO, ADVERTENCIA, o PRECAUCIÓN) para indicar la

probabilidad y la gravedad potencial de las lesiones. Además, se usa un símbolo de

peligro para representar el tipo de riesgo.

PELIGRO indica un riesgo que, si no se evita, ocasionará la muerte o lesiones

graves.

ADVERTENCIA indica un riesgo que, si no se evita, podría ocasionar la muerte o

lesiones graves.

PRECAUCIÓN indica un riesgo que, si no se evita, podría ocasionar lesiones

menores o moderadas.

AVISO indica información que se considera importante pero que no está relacionada

con un peligro.

Símbolos de peligro y significados

Información de seguridad

sobre peligros que pueden

conllevar a lesiones

personales.

Lea y entienda el Manual

del operador antes

de operar y realizar

mantenimientos a la

unidad.

Peligro de incendio Peligro de explosión

Peligro de descarga

eléctrica

Peligro de vapores tóxicos

Peligro de superficie

caliente

Peligro de retroceso

violento

Peligro de amputación:

piezas móviles

Nivel de combustible -

Máximo

No lo llene en exceso

Mensajes de seguridad

ADVERTENCIA

Este producto puede exponerlo a sustancias químicas, entre las que se incluyen

emisiones de escape de motor de gasolina, reconocidas por el estado de California

como causantes de cáncer, y monóxido de carbono, reconocido por el estado de

California como causante de defectos de nacimiento u otros problemas reproductivos.

Para obtener más información, visite www.P65Warnings.ca.gov.

ADVERTENCIA

Los motores Briggs & Stratton® no están diseñados, y no deben utilizarse, para

potenciar carritos motorizados; go karts; vehículos para niños; vehículos recreativos;

vehículos deportivos todo terreno (ATV); motocicletas; aerodeslizadores; equipo

aeronáutico; o vehículos utilizados en eventos de competencia que no estén avalados

por Briggs & Stratton. Para obtener información acerca de productos de carrera

profesionales, consulte www.briggsracing.com. Para usar el motor en ATV utilitarios

y sidebyside, comuníquese con el Centro de aplicaciones de potencia de Briggs &

Stratton llamando al 1-866-927-3349. El uso incorrecto del motor podría provocar

lesiones graves o la muerte.

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando agregue combustible

• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de

dos(2) minutos para asegurarse de que el motor esté frío.

• Llene el tanque de combustible al aire libre o en un área con buena circulación

de aire.

• No ponga demasiado combustible en el tanque. Para permitir la expansión del

combustible, no llene el tanque de combustible arriba de la parte inferior del

cuello.

• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,

calor y otras fuentes de ignición.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• Si el combustible se derrama, espere a que se seque antes de arrancar el

motor.

Cuando arranque el motor

• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el limpiador

de aire (si tiene) estén correctamente instalados.

• No arranque el motor si retiró la bujía.

• Si el motor está inundado, lleve el estrangulador (si tiene) a la posición

ABIERTO o MARCHA. Mueva el acelerador (si tiene) a la posición RÁPIDO y de

arranque hasta que el motor se encienda.

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

Cuando opere el equipo

• No incline el motor o el equipo en un ángulo que cause derramamiento del

combustible.

• No cebe el carburador (si tiene) para detener el motor.

• Nunca arranque u opere el motor sin el limpiador de aire (si tiene) o el filtro de

aire (si tiene).

12 vanguardpower.com

Not for

Reproduction

Cuando lleve a cabo mantenimiento

• Si drena el aceite desde el tubo de llenado de aceite superior, el tanque de

combustible debe estar vacío. Si no está vacío, puede producirse un derrame de

combustible y podría ocasionarse un incendio o una explosión.

• Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de

que el tanque de combustible, si está montado en el motor, esté vacío y

que el extremo del motor donde está la bujía esté elevado. Si el tanque de

combustible no está vacío, puede producirse un derrame de combustible y

podría ocasionarse un incendio o una explosión.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• No cambie el resorte del regulador, las conexiones u otras piezas para

aumentar la velocidad del motor.

• No golpee el volante con un martillo o un objeto duro. Esto podría provocar una

falla en el volante durante la operación.

• Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas

en la misma posición que las piezas originales. Otras piezas podrían provocar

daños o lesiones.

Cuando traslada la ubicación del equipo

• Asegúrese de que el tanque de combustible esté VACÍO o que la válvula de

cierre de combustible esté en la posición CERRADA.

Cuando el combustible o el equipo está almacenado con combustible en el

tanque de combustible

• Puesto que las luces piloto u otras fuentes de ignición pueden causar

explosiones, mantenga el combustible o el equipo lejos de hornos, estufas,

calentadores de agua u otros aparatos que tengan luces piloto.

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

El arranque del motor causa una chispa que podría provocar un incendio o una

explosión.

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

ADVERTENCIA

PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de

carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no huela

los gases del escape, puede estar expuesto al peligroso gas de monóxido de

carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este producto,

diríjase hacia un lugar con aire fresco DE INMEDIATO. Consulte a un médico. Es

probable que se haya intoxicado con monóxido de carbono.

• El gas de monóxido de carbono puede acumularse en los espacios habitados.

Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere

este producto al aire libre, lejos de ventanas, puertas y ventilaciones.

• Instale alarmas de monóxido de carbono operadas por baterías o alarmas

de monóxido de carbono para enchufar con batería de respaldo según lo

que especifiquen las instrucciones del fabricante. Los detectores de humo no

detectan el gas de monóxido de carbono.

• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,

cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las

puertas y ventanas abiertas a manera de ventilación. Después de la operación

de este producto, el monóxido de carbono puede acumularse rápidamente en

estos espacios y permanecer durante horas.

• SIEMPRE ubique este producto a favor del viento y mantenga el escape del

motor alejado de los espacios confinados.

ADVERTENCIA

La retracción rápida del cordón del arrancador (retroceso) tirará de su mano y

brazo hacia el motor más rápido de lo que puede sostenerlo. Podrían presentarse

roturas en los huesos, fracturas, contusiones, o torceduras.

• Para evitar el retroceso al arrancar el motor, hale del cordón del arrancador

lentamente hasta sentir resistencia y luego suéltelo rápidamente.

• Antes de arrancar el motor, desconecte o retire cualquier carga externa del

motor/equipo.

• Asegúrese de que los componentes del equipo acoplados directamente, entre

otros, cuchillas, propulsores, poleas y ruedas dentadas estén firmemente

acoplados.

ADVERTENCIA

Las partes giratorias pueden atrapar las manos, los pies, el cabello, la ropa o los

accesorios y provocar una amputación o laceración traumática.

• Opere el equipo con protectores correctamente instalados.

• Mantenga sus manos y pies alejados de las piezas giratorias.

• Quítese las joyas y asegúrese de que el pelo largo esté apartado de todas las

piezas giratorias.

• No use ropa suelta o artículos que puedan quedar atrapados.

ADVERTENCIA

Durante la operación, el motor y el silenciador se calientan. Si toca un motor

caliente, pueden producirse quemaduras térmicas.

Los materiales combustibles, como hojas, césped y hierbas se pueden inflamar.

• Antes de tocar el motor o el silenciador, detenga el motor y espere dos(2)

minutos. Asegúrese de que el motor y el silenciador se puedan tocar con

seguridad.

• Quite los residuos del silenciador y del motor.

Es una infracción del Código de Recursos Públicos de California (California Public

Resource Code), Sección4442, utilizar u operar el motor en cualquier terreno forestal o

cubierto por árboles o césped, a menos que el sistema de escape esté equipado con un

supresor de chispas, en virtud de la Sección4442, el cual se debe mantener en buenas

condiciones de operación. Es posible que otros estados o jurisdicciones federales

cuenten con leyes similares; consulte la Regulación Federal 36CFR Sección261.52.

Póngase en contacto con el vendedor, el distribuidor o el fabricante del equipo original

para obtener un extintor de chispas diseñado para el sistema de escape instalado en

este motor.

ADVERTENCIA

La chispa accidental del motor puede provocar una descarga eléctrica, un

incendio o una explosión y podría resultar en un enredo, una amputación

traumática o una laceración.

Antes de que realice ajustes o reparaciones:

• Desconecte todos los cables de las bujías y manténgalos alejados de las bujías.

• Desconecte el cable de la batería del terminal negativo de la batería (solo

motores con arranque eléctrico).

• Use solamente las herramientas correctas.

Cuando verifique si hay chispa:

• Use un probador de bujías aprobado.

• No revise si hay chispa con la bujía extraída.

ADVERTENCIA

Los vapores del combustible son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Si siente olor a gas

• No arranque el motor.

• No encienda interruptores eléctricos.

• No use un teléfono en las cercanías.

• Desaloje el área.

• Comuníquese con el proveedor de gas o con los bomberos.

Características y controles

Controles del motor

Compare las letras de las leyendas en las Figuras 1 y 2 con los controles del motor en

la lista a continuación:

A. Números de identificación del motorModelo - Tipo - Código

B. Bujía

C. Limpiador de aire, bajo perfil

D. Tapones de la varilla

E. Llenado de aceite

F. Filtro de aceite

G. Tapón de drenaje de aceite

H. Sensor de presión de aceite

I. Rejilla de toma de aire

Not for

Reproduction

J. Arrancador eléctrico

K. Solenoide del arrancador

L. Regulador/Rectificador

M. Enfriador de aceite (si está equipado)

N. Silenciador (de estar equipado)

O. Bomba de combustible

P. Interruptor de arranque1

Q. Filtro de combustible (si tiene)

Algunos motores y equipos cuentan con controles remotos. Consulte el manual del

equipo para conocer la ubicación y la operación de los controles remotos.

Símbolos de control del motor y significados

Velocidad del motor -

RÁPIDA

Velocidad del motor -

LENTA

Velocidad del motor -

DETENER

ENCENDIDO/APAGADO

Arranque del motor

Estrangulador CERRADO

Arranque del motor

Estrangulador ABIERTO

Tapa del combustible

Válvula de cierre de

combustible - ABIERTO

Válvula de cierre de

combustible - CERRADO

Operación

Recomendaciones sobre el aceite

Capacidad de aceite: Consulte la sección Especificaciones.

Recomendamos el uso de aceites Briggs&Stratton® con garantía certificada para

un mejor rendimiento. Se permiten otros aceites detergentes de alta calidad, si están

clasificados para servicio SF, SG, SH, SJ o superior. No use aditivos especiales.

Use el cuadro para seleccionar la mejor viscosidad para el margen de temperatura

exterior que se espera. Los motores de la mayoría de los equipos eléctricos para

exteriores funcionan bien con aceite sintético 5W-30. Para equipos que operan a altas

temperaturas, el aceite sintético Vanguard® 15W-50 brinda la mejor protección.

A SAE30 - El uso de SAE30 a temperaturas inferiores a 40°F (4°C) provocará

dificultades de arranque.

B 10W-30 - El uso de 10W-30 a temperaturas mayores a 80°F (27°C) puede

provocar un aumento en el consumo de aceite. Verifique el nivel de aceite con

frecuencia.

C 5W-30

D 5W-30 sintético

EVanguard®Sintético 15W-50

Verifique el nivel de aceite

Antes de verificar o agregar aceite

• Asegúrese de que el motor esté nivelado.

• Limpie todos los desechos del área de llenado de aceite.

• Consulte la sección Especificacionespara obtener la capacidad de aceite.

AVISO

Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o

distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el

motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue

el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor

sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la

garantía.

1. Retire la varilla indicadora de nivel (A, Figura 3) y séquela con un paño limpio.

2. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 3).

3. Retire la varilla y revise el nivel de aceite. Asegúrese de que el nivel de aceite

esté en la parte superior del indicador de lleno (B, Figura 3) de la varilla indicadora

de nivel de aceite.

4. Si el nivel de aceite es bajo, agregue aceite lentamente en el llenado de aceite del

motor (C, Figura 3). No agregue demasiado aceite.

5. Espere un minuto y verifique el nivel de aceite. Asegúrese de que el nivel de

aceite sea el correcto.

6. Instale y ajuste la varilla indicadora de nivel de aceite (A, Figura 3).

Sistema de protección de bajo nivel de aceite (si

está instalado)

En algunos motores se ha instalado un sensor de bajo nivel de aceite. Si el nivel

de aceite está bajo, el sensor mostrará una luz de advertencia o detendrá el motor.

Detenga el motor y siga los pasos a continuación antes de arrancar el motor.

• Asegúrese de que el motor esté nivelado.

• Haga una comprobación del nivel de aceite. Consulte la secciónVerificación

del nivel de aceite.

• Si el nivel de aceite es bajo, agregue la cantidad correcta de aceite. Arranque

el motor y asegúrese de que la luz de advertencia (si está instalada) no se

encienda.

• Si el nivel de aceite es bajo, no arranque el motor. Comuníquese con un

distribuidor de servicio autorizado de Briggs & Stratton para corregir el problema

del aceite.

Recomendaciones acerca del combustible

El combustible debe cumplir con estos requisitos:

• Gasolina limpia, fresca y sin plomo.

• Un mínimo de 87octanos/87AKI (91RON). Para uso en grandes alturas,

consulte a continuación.

• Se permite gasolina con hasta un 10% de etanol (gasohol).

AVISO

No utilice gasolina no aprobada, como la E15 y la E85. No mezcle la gasolina con

aceite ni cambie el motor para usarlo con combustibles alternativos. El uso de

combustibles no aprobados podría provocar daños a los componentes del motor, lo que

no será reparado bajo la garantía.

Para proteger el sistema de combustible de la formación de goma y la corrosión, mezcle

el combustible con un estabilizador de combustible sin alcohol y un tratamiento de

etanol. Consulte la sección Almacenamiento. No todos los combustibles son iguales.

Si ocurren problemas de arranque o de rendimiento, cambie el proveedor o la marca

del combustible. Este motor está certificado para funcionar con gasolina. El sistema

de control de emisiones para motores carburados es EM (modificaciones del motor).

Los sistemas de control de emisiones para motores con inyección de combustible

electrónica son ECM (módulo de control del motor), MPI (inyección multipuerto) y, si lo

tiene, un O2S (sensor de oxígeno).

Gran altura

En alturas de más de 5000pies (1524metros), se permite una gasolina con un mínimo

de 85octanos/85AKI (89 RON).

Para motores carburados, se requiere realizar el ajuste de gran altura para mantener

el rendimiento. El funcionamiento sin este ajuste provocará una disminución en

el rendimiento y un aumento en el consumo de combustible y en las emisiones.

Comuníquese con un Distribuidor de Servicio Autorizado por Briggs & Stratton para

obtener información sobre el ajuste de gran altura. No se recomienda operar la

máquina a alturas menores de 2500pies (762metros) con el ajuste de gran altura.

En el caso de motores con inyección de combustible electrónica (EFI), no se requiere

un ajuste de gran altura.

14 vanguardpower.com

Not for

Reproduction

Agregar combustible

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando agregue combustible

• Detenga el motor. Antes de quitar la tapa del combustible, espere un mínimo de

dos(2) minutos para asegurarse de que el motor esté frío.

• Llene el tanque de combustible al aire libre o en un área con buena circulación

de aire.

• No ponga demasiado combustible en el tanque. Para permitir la expansión del

combustible, no llene el tanque de combustible arriba de la parte inferior del

cuello.

• Mantenga el combustible alejado de chispas, llamas abiertas, llamas piloto,

calor y otras fuentes de ignición.

• Examine frecuentemente las líneas de combustible, el tanque de combustible, la

tapa del combustible y las conexiones en busca de grietas o fugas. Reemplace

las piezas dañadas.

• Si el combustible se derrama, espere a que se seque antes de arrancar el

motor.

1. Limpie la suciedad y los desechos en el área de la tapa de llenado de combustible.

Retire la tapa de llenado de combustible.

2. Llene el tanque de combustible (A, Figura 4) con combustible. Puesto que el

combustible se expandirá, no llene más arriba de la parte inferior del cuello del

tanque de combustible (B).

3. Instale la tapa de llenado de combustible.

Arranque del motor

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Cuando arranque el motor

• Asegúrese de que la bujía, el silenciador, la tapa del combustible y el limpiador

de aire (si tiene) estén correctamente instalados.

• No arranque el motor si retiró la bujía.

• Si el motor está inundado, lleve el estrangulador (si tiene) a la posición

ABIERTO o MARCHA. Mueva el acelerador (si tiene) a la posición RÁPIDO y de

arranque hasta que el motor se encienda.

• Si hay alguna filtración de gas natural o gas LP en el área, no arranque el motor.

• Puesto que los vapores son inflamables, no utilice fluidos de encendido

presurizados.

ADVERTENCIA

PELIGRO DE GAS NOCIVO. Las emisiones del motor contienen monóxido de

carbono, un gas nocivo que podría causar la muerte en minutos. Aunque no huela

los gases del escape, puede estar expuesto al peligroso gas de monóxido de

carbono. Si usted se siente enfermo, adormecido, o débil al utilizar este producto,

diríjase hacia un lugar con aire fresco DE INMEDIATO. Consulte a un médico. Es

probable que se haya intoxicado con monóxido de carbono.

• El gas de monóxido de carbono puede acumularse en los espacios habitados.

Para reducir el riesgo del gas de monóxido de carbono, SOLAMENTE opere

este producto al aire libre, lejos de ventanas, puertas y ventilaciones.

• Instale alarmas de monóxido de carbono operadas por baterías o alarmas

de monóxido de carbono para enchufar con batería de respaldo según lo

que especifiquen las instrucciones del fabricante. Los detectores de humo no

detectan el gas de monóxido de carbono.

• NO opere este producto en viviendas, garajes, sótanos, espacios reducidos,

cobertizos u otros espacios cerrados, incluso si usa ventiladores o deja las

puertas y ventanas abiertas a manera de ventilación. Después de la operación

de este producto, el monóxido de carbono puede acumularse rápidamente en

estos espacios y permanecer durante horas.

• SIEMPRE ubique este producto a favor del viento y mantenga el escape del

motor alejado de los espacios confinados.

AVISO

Este motor fue enviado desde Briggs&Stratton sin aceite. Los fabricantes o

distribuidores del equipo podrían haber agregado aceite al motor. Antes de arrancar el

motor por primera vez, asegúrese de que el nivel de aceite sea el correcto. Agregue

el aceite como se especifica en las instrucciones de este manual. Si arrancar el motor

sin aceite, se presentarán daños y la reparación del motor no estará cubierta por la

garantía.

NOTA:Su equipo podría tener controles remotos. Consulte el manual del equipo para

conocer la ubicación y el funcionamiento de los controles remotos

Para obtener información sobre cómo arrancar el motor, lea las instrucciones de

operación suministradas por el fabricante del equipo.

Sistema de inyección de combustible electrónica(EFI)

1. Revise el aceite del motor. Consulte la secciónVerificación del nivel de aceite.

2. Asegúrese de que los controles de transmisión del equipo, si están instalados,

estén desconectados.

3. Mueva el cierre de combustible (A, Figura 5), si está instalado, a la posición

ABIERTO

4. Mover el control del acelerador a la posición LENTO.

5. Presione el interruptor de detención (D, Figura5), si está instalado, a la posición

ENCENDIDO.

6. Gire el interruptor de arranque eléctrico (E, Figura5) a la posición ENCENDIDO o a

la posición ARRANQUE.

AVISOPara prolongar la vida útil del arrancador, haga ciclos cortos de arranque (cinco

segundos como máximo). Espere un minuto entre los ciclos de arranque.

Si el motor no arranca después de 3o 4intentos, póngase en contacto con su

distribuidor local o vaya a vanguardpower.com o llame 1-800-999-9333.

Detención del motor

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

• No cebe el carburador (si tiene) para detener el motor.

1. Interruptor de detención, si está instalado: Mueva el interruptor de parada (D,

Figura 6) a la posición APAGADO.

2. Interruptor de llave, si está instalado: Ajuste el control del acelerador a la

posición LENTO. Gire el interruptor de llave (E, Figura6) a la posición APAGADO.

Retire la llave y manténgala en un sitio seguro fuera del alcance de los niños.

3. Después de que se haya detenido el motor, mueva el cierre de combustible (A,

Figura6), si está instalado, a la posición CERRADO.

Mantenimiento

Información de mantenimiento

ADVERTENCIA

El combustible y sus vapores son inflamables y explosivos. El fuego o una

explosión podrían provocar quemaduras o la muerte.

Durante el mantenimiento, si es necesario inclinar la unidad, asegúrese de que el

tanque de combustible, si está montado en el motor, esté vacío y que el extremo del

motor donde está la bujía esté elevado. Si el tanque de combustible no está vacío,

puede producirse un derrame de combustible y podría ocasionarse un incendio o una

explosión. Si el motor está inclinado en una dirección diferente, no arrancará fácilmente

debido a la contaminación del filtro de aire o de la bujía por aceite o combustible.

ADVERTENCIA

La chispa accidental del motor puede provocar una descarga eléctrica, un

incendio o una explosión y podría resultar en un enredo, una amputación

traumática o una laceración.

Antes de que realice ajustes o reparaciones:

• Desconecte todos los cables de las bujías y manténgalos alejados de las bujías.

• Desconecte el cable de la batería del terminal negativo de la batería (solo

motores con arranque eléctrico).

• Use solamente las herramientas correctas.

Cuando verifique si hay chispa:

• Use un probador de bujías aprobado.

• No revise si hay chispa con la bujía extraída.

ADVERTENCIA

Las piezas de repuesto deben ser del mismo diseño y deben ser instaladas en la misma

posición que las piezas originales. Otras piezas podrían provocar daños o lesiones.

AVISO

Todos los componentes usados para armar este motor deben permanecer en su lugar

para un funcionamiento apropiado.

Not for

Reproduction

Consulte a un distribuidor de servicio autorizado de Briggs & Stratton para todo el

mantenimiento y servicio del motor y las piezas del motor.

Mantenimiento del control de emisiones

Para el mantenimiento, la sustitución o la reparación de los dispositivos y

sistemas de control de emisiones, póngase en contacto con un establecimiento

de reparación de motores todo terreno calificado o con un técnico de servicio. Sin

embargo, para obtener un servicio de control de emisiones “sin costo”, el trabajo debe

ser realizado por un distribuidor autorizado de la fábrica. Consulte las Declaraciones de

Control de Emisiones.

Programa de mantenimiento

Intervalos de 8horas o diariamente

• Revise el nivel de aceite del motor.

• Limpie el área alrededor del silenciador y los controles.

Intervalos de 100 horas o anualmente

• Reemplace las bujías.

• Cambie el aceite del motor.

• Reemplace el filtro de aceite (si está instalado).

•Mantenimiento del filtro de aire. 1.

•Limpie el prefiltro (si está instalado)1 .

• Realice el mantenimiento del sistema de escape.

Intervalos de 250horas o anualmente

• Verifique el espacio libre de la válvula. Ajústelo si es necesario.

Intervalos de 400 horas o anualmente

• Reemplace el filtro de aire.

• Reemplace el filtro de combustible.

•Mantenimiento del sistema de refrigeración por aire1.

•Limpie las aberturas del refrigerador de aceite1.

1 Limpie con más frecuencia en condiciones de polvo o cuando haya muchas partículas

en el aire.

Sistema de inyección de combustible electrónica

(EFI)

El sistema EFI controla la temperatura del motor, la velocidad del motor y el voltaje de

la batería para el arranque y el calentamiento del motor. El sistema no tiene ajustes. Si

hay problemas de arranque u operación, póngase en contacto con un distribuidor de

servicio autorizado de Briggs & Stratton.

AVISOAsegúrese de obedecer los pasos que figuran a continuación pues de lo

contrario podría presentarse daño en el sistema EFI.

• NO arranque el motor si los cables de la batería están flojos.

• Gire la llave a la posición APAGADO antes de desconectar, retirar y/o instalar la

batería.

• NO use un cargador de baterías para arrancar el motor.

• NO desconecte los cables de la batería durante la operación del motor.

• Cuando desconecte los cables de la batería, conecte el cable positivo (+)

primero y, luego conecte el cable negativo (-) a la batería.

• Cuando se cargue la batería, gire el interruptor de encendido a la posición

APAGADO y desconecte el cable negativo (-) de la batería.

• NO rocíe con agua el módulo de control electrónico.

Mantenimiento de las bujías

Verifique la separación entre bujías (A, Figura7) con un calibrador de bujías (B). Si

es necesario, ajuste la separación entre bujías. Instale y apriete la bujía con el par

de torsión correcto. Para obtener información acerca de las especificaciones de la

separación o del par de torsión, consulte la sección Especificaciones.

Mantenimiento del sistema de escape