Sony VPL-PX1 Manuel utilisateur

 1999 Sony Corporation

3-867-701-11(3)

VPL-PX1

Operating Instructions

Mode d’emploi

Manual de instrucciones

FR

ES

LCD Data Projector

GB

2 (GB)

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open the

cabinet. Refer servicing to qualified

personnel only.

This symbol is intended to alert the

user to the presence of uninsulated

“dangerous voltage” within the

product’s enclosure that may be of

sufficient magnitude to constitute a risk

of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance (servicing)

instructions in the literature

accompanying the appliance.

WARNING

This label is located on

the rear of the Remote

Commander.

This label is located on the

rear of the Remote

Commander.

Caution

use of controls or adjustments or performance of

procedures other than those specified herein may result in

hazardous radiation exposure.

Notes

• Do not aim the laser at people or not look into the laser

transmitter.

• When the Remote Commander causes malfunction,

consult with qualified Sony personnel. We change the

Remote Commander as new one according to the

guarantee.

This label is located on the

rear of the Remote

Commander.

Laser light shines out of this window.

For the customers in the USA

This equipment has been tested and found to comply with

the limits for a Class A digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a

residential area is likely to cause harmful interference in

which case the user will be required to correct the

interference at his own expense.

You are cautioned that any changes or modifications not

expressly approved in this manual could void your authority

to operate this equipment.

This label is located on

the side of the Remote

Commander.

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS 2 LASER PRODUCT

RAYONNEMENT LASER

NE PAS REGARDER DANS LE FAISCEAU

APPAREIL A LASER DE CLASSE 2

LASER–STRAHLING

NIGHT IN DEN STRAHL BLICKEN

LASER KLASSE 2

MAX OUTPUT:1mW

WAVE LENGTH:645nm

LASER RADIATION

DO NOT STARE INTO BEAM

WAVE LENGTH:645nm

MAX OUTPUT:1mW

CLASS II LASER PRODUCT

COMPLIES WITH DHHS 21 CFR

SUBCHAPTER J

SONY CORPORATION

6-7-35 KITASHINAGAWA

SHINAGAWA-KU,TOKYO,JAPAN

A

MANUFACTURED;

CAUTION

AVOID EXPOSURE

-

LASER

RADIATION IS EMITTED

FROM THIS APERTURE.

3 (GB)

For the customers in Canada

This Class A digital apparatus complies with Canadian

ICES-003.

For the customers in the United Kingdom

WARNING

THIS APPARATUS MUST BE EARTHED

IMPORTANT

The wires in this mains lead are coloured in accordance with

the following code:

Green-and-Yellow: Earth

Blue: Neutral

Brown: Live

As the colours of the wires in the mains lead of this

apparatus may not correspond with the coloured markings

identifying the terminals in your plug proceed as follows:

The wire which is coloured green-and-yellow must be

connected to the terminal in the plug which is marked by the

letter E or by the safety earth symbol I or coloured green

or green-and-yellow.

The wire which is coloured blue must be connected to the

terminal which is marked with the letter N or coloured black.

The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red.

Voor de klanten in Nederland

Bij dit product zijn batterijen geleverd.

Wanneer deze leeg zijn, moet u ze niet

weggooien maar inleveren als KCA.

The socket-outlet should be installed near the equipment

and be easily accessible.

Warning on power connection

Use a proper power cord for your local power supply.

The United States, Continental UK, Ireland, Japan

Canada Europe Australia, Newzealand

Plug type VM0233 290B YP-12A COX-07 —

1)

VM1296

Female end VM0089 386A YC-13B COX-02 VM0310B VM10505

Cord type SJT SJT H05VV-F H05VV-F N13237/CO-228 HVCTF

Rated Voltage & Current 10A/125V 10A/125V 10A/250V 10A/250V 10A/250V 13A/125V

Safety approval UL/CSA UL/CSA VDE VDE VDE DENTORI

1) Note: Use an appropriate rating plug which is applied to local regulations.

4 (GB)

5 (GB)

English

GB

Table of Contents

Overview

Precautions ............................................................... 6 (GB)

Features..................................................................... 7 (GB)

Location and Function of Controls......................... 8 (GB)

Front/Left Side ......................................................... 8 (GB)

Rear/Right Side/Bottom........................................... 8 (GB)

Control panel.......................................................... 10 (GB)

Connector panel ..................................................... 11 (GB)

Remote Commander .............................................. 12 (GB)

Setting up and projecting

Installing the Projector........................................... 14 (GB)

Connecting.............................................................. 14 (GB)

Connecting with a Computer ................................. 14 (GB)

Connecting with a VCR/15k RGB/

Component Equipment ..................................... 16 (GB)

Projecting ................................................................ 17 (GB)

Adjustments and settings using the menu

Using the MENU...................................................... 19 (GB)

The PICTURE CTRL Menu ..................................... 19 (GB)

The INPUT SETTING Menu .................................... 21 (GB)

The SET SETTING Menu ........................................ 23 (GB)

Maintenance

Maintenance............................................................ 24 (GB)

Replacing the Lamp ............................................... 24 (GB)

Cleaning the Air Filter ........................................... 25 (GB)

Troubleshooting ..................................................... 26 (GB)

Other

Tips for Installation ................................................ 28 (GB)

Unsuitable Installation ........................................... 28 (GB)

Notes on Installation .............................................. 28 (GB)

Specifications ......................................................... 29 (GB)

Index ........................................................................ 32 (GB)

6 (GB)

Precautions

On safety

•Check that the operating voltage of your unit is

identical with the voltage of your local power

supply.

•Should any liquid or solid object fall into the cabinet,

unplug the unit and have it checked by qualified

personnel before operating it further.

•Unplug the unit from the wall outlet if it is not to be

used for several days.

•To disconnect the cord, pull it out by the plug. Never

pull the cord itself.

•The wall outlet should be near the unit and easily

accessible.

•The unit is not disconnected to the AC power source

(mains) as long as it is connected to the wall outlet,

even if the unit itself has been turned off.

•Do not look into the lens while the lamp is on.

•Do not aim the laser at people or not look into the

laser transmitter.

•Do not place your hand or objects near the

ventilation holes — the air coming out is hot.

•Be careful not to catch your fingers by the adjuster

when you lift up the projector. Do not push hard on

the top of the projector with the adjuster out.

On illumination

•To obtain the best picture, the front of the screen

should not be exposed to direct lighting or sunlight.

•Ceiling-mounted spot lighting is recommended. Use

a cover over fluorescent lamps to avoid lowering the

contrast ratio.

•Cover any windows that face the screen with opaque

draperies.

•It is desirable to install the projector in a room where

floor and walls are not of light-reflecting material. If

the floor and walls are of reflecting material, it is

recommended that the carpet and wall paper be

changed to a dark color.

On preventing internal heat build-up

After you turn off the power with the I /

1

key on the

Remote Commander or on the control panel, do not

disconnect the unit from the wall outlet while the

cooling fan is still running.

Caution

The projector is equipped with ventilation holes

(intake) on the right side and ventilation holes

(exhaust) on front and rear. Do not block or place

anything near these holes, or internal heat build-up

may occur, causing picture degradation or damage to

the projector.

On cleaning

•To keep the cabinet looking new, periodically clean

it with a soft cloth. Stubborn stains may be removed

with a cloth lightly dampened with a mild detergent

solution. Never use strong solvents, such as thinner,

benzene, or abrasive cleansers, since these will

damage the cabinet.

•Avoid touching the lens. To remove dust on the lens,

use a soft dry cloth. Do not use a damp cloth,

detergent solution, or thinner.

•Clean the filter at regular intervals.

On repacking

•Save the original shipping carton and packing

material; they will come in handy if you ever have to

ship your unit. For maximum protection, repack your

unit as it was originally packed at the factory.

Precautions

7 (GB)

Overview

Features

High portability

•Light weight/small size

This projector has come to miniaturized to approx. 4

kg (8 lb 13 oz) of mass by adopting magnesium die-

casting body. And a carrying handle is equipped with

the projector. You can easily carry it with your

computer.

Reduced noise

Because the projector is using a new cooling

mechanism, noise has been reduced.

Stability

This projector utilizes a new placing angle adjuster to

improve stability.

High brightness, high picture quality

•High brightness

Adopting the new developed optical system and the

new developed 120 W UHP lamp allow high

brightness (light output 1000 ANSI lumen) and

excellent uniformity on the picture.

•High resolution

Three 0.9-inch, about 790,000 pixel XGA panels

with micro-lens arrays provide a resolution of 1024 ×

768 dots for RGB input and 750 horizontal TV lines

for video input.

Simple setup, easy presentation

•Simple setup with external equipment

This projector is preset for 37 kinds of input signals.

You can project images from an external signal

source just by connecting the equipment with the

supplied cable and pushing the APA key.

•Remote Commander with mouse control and

laser pointer functions

You can operate a computer with the Remote

Commander since the unit has a build-in mouse

receiver. For your presentation, you can use the laser

pointer built in the Remote Commander as well.

Accepts various input signals

•Scan converter loaded

This projector has a build-in scan converter which

converts the input signal within 1024 × 768 dots.

•Compatible input signals

This projector accepts video signals of the

composite, S video, and component as well as the

15k RGB, VGA

1)

, SVGA

1)

, XGA

1)

, and SXGA

1)

signals, which all can be displayed.

•Compatible with five color systems

NTSC, PAL, SECAM, NTSC

4.43

2)

, or PAL-M color

system can be selected automatically or manually.

.........................................................................................................................................................................................................

1) VGA, SVGA, XGA, and SXGA are registered trademarks of the International Business Machines Corporation, U.S.A.

2) NTSC4.43 is the color system used when playing back a video recorded on NTSC on a NTSC4.43 system VCR.

Features

8 (GB)

Location and Function of

Controls

Front/Left Side

1 Zoom ring

Adjusts the size of the picture.

2 Focus ring

Adjusts the picture focus.

3 Front remote control detector (SIRCS receiver)

4 Lens

Open the lens shutter before projection.

5 Lens shutter

6 Ventilation holes (exhaust)

7 Adjuster

When a picture is projected on the out of the screen,

adjust the picture using this adjuster.

For details on how to use the adjusters, see “How to use

the adjuster” on page 9 (GB).

8 Left speaker

9 Control panel

For details, see “Control panel” on page 10 (GB).

0 Carrying handle

Pull up the handle from the projector for carrying.

Note

Be careful not to injure your fingers when you fold in

the handle.

qa Rear remote control detector (SIRCS receiver)

qs AC IN socket

Connects the supplied AC power cord.

Rear/Right Side/Bottom

Location and Function of Controls

9

8

0

3

4

5

6

7

2 1

qk

ql

qd

qg

qj

qa

6

qs

qf

qh

w;

9 (GB)

qd Security lock

Connects to an optional security cable (Kensington’s).

The security lock corresponds to Kensington’s

MicroSaver Security System.

If you have any comment, contact

Kensington

2853 Campus Drive, San Mates, CA 94403

U.S.A.

Tel: 800-535-4242: extension 3348

Home page address:

http://www.kensington.com/

qf 75Ω termination switch (bottom)

Normally set to ON. Set it to OFF when the projector

is connected to a computer or a monitor.

qg Connector panel

For details, see page 11 (GB).

qh Lamp cover (bottom)

qj Adjuster button

qk Right speaker

ql Ventilation holes (intake)/air filter cover

Notes

•Do not place anything near the ventilation holes as it

may cause internal heat build-up.

•Do not place your hand or objects near the

ventilation holes — the air coming out is hot.

w; Air filter cover button

Used to remove the air filter cover.

For details, see “Cleaning the Air Filter” on page 25 (GB).

Adjuster button

How to use the adjuster

To adjust the height

Adjust the height of the projector as follows:

1 Lift the projector and press the adjuster button.

The adjuster will extend from the projector.

2 While pressing the button, lower the projector.

Then, release the button.

Note

The adjuster has 5 settings. After releasing the

adjuster button, the height will be locked at next level.

Location and Function of Controls

10 (GB)

Location and Function of Controls

Control panel

1

I

/

1

(

on / standby

)

key

Turns on and off the projector when the projector is in

the standby mode. The ON/STANDBY indicator

lights in green when the power is turned on.

When turning off the power, press the I /

1

key

twice following the message on the screen, or press

and hold the key for about one second.

For details on steps for turning off the power, see “To turn

off the power” on page 18 (GB).

2 INPUT key

Selects the input signal. Each time you press the key,

the input signal switches between video/audio input

and INPUT A connector.

3 MENU key

Displays the on-screen menu. Press again to clear the

menu.

4 ENTER key

Enters the settings of items in the menu system.

5 RESET key

Resets the value of an item back to its factory preset

value. This key functions when the menu or a setting

item is displayed on the screen.

6 Arrow keys (M/m/</,)

Used to select the menu or to make various

adjustments.

7 VOLUME +/– keys

Adjust the volume of the built-in speakers and output

level of the AUDIO OUT jack.

+ : Increases the volume.

– : Decreases the volume.

8 APA (Auto Pixel Alignment) key

Adjusts a picture to be projected clearest

automatically while a signal from the computer is

input.

9 Indicators

LAMP/COVER: Lights up or flashes under the

following conditions:

• Lights up when the lamp has reached the end of

its life or becomes a high temperature.

• Flashes when the lamp cover or air filter cover

is not secured firmly.

TEMP (Temperature)/FAN: Lights up or flashes

under the following conditions:

• Lights up when temperature inside the projector

becomes unusually high.

• Flashes when the fan is broken.

POWER SAVING: Lights up when the projector is

in the power saving mode. When POWER

SAVING in the SET SETTING menu is set to

ON, the projector goes into the power saving

mode if no signal is input for 10 minutes.

Although the lamp goes out, the cooling fan

keeps running. In the power saving mode, any

key does not function for the first 30 seconds.

The power saving mode is canceled when a signal

is input or any key is pressed.

ON/STANDBY: Lights up or flashes under the

following conditions:

• Lights in red when the AC power cord is

plugged into the wall outlet. Once in the

standby mode, you can turn on the projector

with the

I / 1

key on the Remote Commander or on the

control panel.

• Lights in green when the power is turned on.

• Flashes in green while the cooling fan runs after

turning off the power with the

I / 1

key. The

fan runs for about 90 seconds after turning off

the power.

The ON/STANDBY indicator flashes quickly

for the first 30 seconds.

During this time, you cannot turn the power

back on with the

I / 1

key.

For details on the LAMP/COVER and the TEMP/FAN

indicators, see page 27 (GB).

APA

VOLUME

INPUT

MENU

ENTER

RESET

ON

/STANDBY

POWER

SAVING

TEMP

/FAN

LAMP

/COVER

9

1

2

3

4

8

7

6

5

11 (GB)

Connector panel

1 Video/audio input connector

Connect to external video equipment such as a VCR.

S VIDEO (mini DIN 4-pin): Connects to the

S video output (Y/C video output) of a video

equipment.

VIDEO (phono type): Connects to the composite

video output of video equipment.

Note

If you connect video equipment to both the

S VIDEO and VIDEO jacks, the signal from the

S VIDEO jack is selected. When projecting the

picture via the VIDEO jack, be sure not to connect a

cable to the S VIDEO jack.

AUDIO input L (MONO)/R jacks (phono type):

Connect to the audio output of equipment. For

stereo equipment, use both the L and R jacks; for

monaural equipment, use the L (MONO) jack

only.

Right side

Location and Function of Controls

2 INPUT A connector

Connect to external equipment such as a computer.

You can control the mouse signal with the Remote

Commander.

INPUT A (HD D-sub 15-pin, female): Connects to

the monitor output on a computer using the

supplied cable. When inputting a component or,

15k RGB signal, use the optional cable.

MOUSE (13-pin): Connects to the mouse port on a

computer to control the mouse function using the

supplied mouse cable.

AUDIO IN (stereo minijack): Connects to the

audio output on a computer to input the audio

signal.

3 AUDIO OUT jack (stereo minijack)

Connects to external active speakers.

The volume of the speakers can be controlled by the

VOLUME keys on the Remote Commander or the

control panel.

S VIDEO VIDEO L AUDIO R

AUDIO OUT

AUDIO IN

MOUSE

INPUT A

13

2

12 (GB)

6 R CLICK key

Functions as a right button on a mouse. When

connected to a Macintosh

1)

computer, the R CLICK

key functions as a mouse button.

7 RESET key

8 VOLUME +/– keys

9 Strap holder

Attaches the supplied strap.

0 CONTROL S OUT jack (stereo minijack)

This jack does not operated with this unit.

Note

The Remote Commander does not function if the

cable is connected to this jack.

qa ENTER key

qs MENU key

qd APA (Auto Pixel Alignment) key

qf MUTING keys

Cut off the picture and sound.

PICTURE: Cuts off the picture. Press again to

restore the picture.

AUDIO: Cuts off the sound from speakers and

AUDIO OUT jack. Press again or press the

VOLUME + key to restore the sound.

qg COMMAND ON/OFF switch

When this switch is set to OFF, no key on the Remote

Commander function. This saves the battery power.

qh Transmission indicator

Lights up when you press a key on the Remote

Commander.

This indicator does not light up when you use the laser

pointer.

qj Infrared transmitter

qk Laser transmitter

Remote Commander

The keys which have the same names as on the

control panel function identically.

You can control a connected computer using the

Remote Commander.

For details, see “Connecting with a Computer” on page

14 (GB).

.........................................................................................................................................................................................................

1) Macintosh is a registered trademark of Apple Computer, Inc.

Location and Function of Controls

COMMAND

MUTING

I / 1

INPUT

APA

MENU

LASER

ENTER

RESET

VOLUME

+

–

R CLICK

PICTUREAUDIO

ONOFF

1

2

3

5

7

6

8

4

qa

qs

qd

qf

qg

qh

qj qk

9,0

ql

Notes on laser beam

•Do not look into the laser transmitter.

•Do not aim the laser at people.

1

I

/

1

key

2 INPUT key

3 LASER key

Emits laser beam from the laser transmitter when you

press this key.

4 Joy stick

Functions as a mouse of a computer connected to the

unit.

5 Arrow keys (M/m/</,)

13 (GB)

ql L CLICK key

Functions as a left button on a mouse. When

connected to a Macintosh computer, the L CLICK key

functions as a mouse button.

Battery installation

1 Push and slide to open the lid, then install the two

size AA (R6) batteries (supplied) with the correct

polarity.

2 Replace the lid.

Notes on batteries

•Make sure that the battery orientation is correct when

inserting batteries.

•Do not mix an old battery with a new one, or

different types of batteries.

•If you will not use the Remote Commander for a

long time, remove the batteries to avoid damage

from battery leakage. If batteries have leaked,

remove them, wipe the battery compartment dry and

replace the batteries with new ones.

Notes on Remote Commander operation

•Make sure that there is nothing to obstruct the

infrared beam between the Remote Commander and

the remote control detector on the projector.

•The operation range is limited. The shorter the

distance between the Remote Commander and the

projector is, the wider the angle within which the

commander can control the projector.

Location and Function of Controls

Be sure to

install the

battery from

the # side.

14 (GB)

Installing the Projector

This section describes the installation arrangements

for installing the projector.

Horizontal center

of the screen

The distance between the lens and the screen varies

depending on the size of the screen. Use the following table

as a guide.

Unit: m (feet)

Screen

size 40 60 80 100 120 150 200

(inches)

Minimum 1.6 2.4 3.3 4.1 5.0 6.2 8.3

Distance (5.2) (8.0) (10.8) (13.5) (16.3) (20.4) (27.4)

Maximum 2.0 3.1 4.2 5.2 6.3 7.9 10.5

Distance (6.7) (10.2) (13.7) (17.1) (20.6) (25.8) (34.5)

Note

You can not install the projector upside down, such

as on a ceiling.

Connecting

Connecting with a Computer

This section describes how to connect the projector

with a computer.

For details on how to connect a VCR, 15k RGB, or

component equipment, see page 16 (GB).

When the projector is connected to a computer, you

can control the mouse of a computer by the Remote

Commander.

The R/L CLICK keys and joy stick function as

follows.

Note

Make sure that there is nothing to obstruct the infrared

beam between the Remote Commander and the

remoter control detector on the projector.

Function

Key and

IBM PC/AT

a)

Macintosh

joy stick

compatible, Serial

R CLICK

(front)

Right button Mouse button

L CLICK

(rear)

Left button Mouse button

Joy stick Corresponds with the movements of the mouse

a) IBM PC/AT is a registered trademark of International

Business Machines Corporation, U.S.A.

Also refer to the instruction manual of equipment to

be connected.

Notes

•This unit accepts the VGA, SVGA, XGA, and

SXGA signals. However, we recommend you to set

the output mode of your computer to the XGA mode

for the external monitor.

•If you set your computer, such as a notebook type

IBM PC/AT compatible, to output the signal to both

the display of your computer and the external

monitor, the picture of the external monitor may not

appear properly. In such cases, set the output mode

of your computer to output the signal to only the

external monitor.

For details, refer to the operating instructions supplied

with your computer.

Distance between the screen

and the center of the lens

Installing the Projector / Connecting

15 (GB)

MOUSE

AUDIO IN

S VIDEO VIDEO L AUDIO R

AUDIO OUT

INPUT A

AUDIO IN

MOUSE

S VIDEO VIDEO L AUDIO R

AUDIO OUT

INPUT A

Setting up and projecting

When making connections, be sure to:

•turn off all equipment before making any

connections.

•use the proper cables for each connection.

•insert the plugs of the cables properly; plugs that are

not fully inserted often generate noise. When pulling

out a cable, be sure to pull it out from the plug, not

the cable itself.

Note

Supplied mouse cables may not work properly

according to your computer.

When connecting with an IBM PC/AT

compatible computer

When connecting with a Macintosh

computer

Computer

Right side

SIC-S21

Mouse

cable for

serial port

(not

supplied)

to serial

port

to mouse

port

SIC-S22

Mouse

cable for

PS/2 port

(supplied)

to

monitor

out

Stereo audio

connecting

cable (not

supplied)

to audio

out

Right side

SIC-S20

Mouse

cable (not

supplied)

to mouse

port

to audio out

to monitor

out

HD D-sub

15-pin

cable

(supplied)

Signal

adapter

(not

supplied)

or

Computer

HD D-sub

15-pin

cable

(supplied)

Connecting

Stereo audio

connecting

cable (not

supplied)

16 (GB)

INPUT A

S VIDEO VIDEO L AUDIO R

AUDIO OUT

AUDIO IN

MOUSE

AUDIO IN

MOUSE

INPUT A

S VIDEO VIDEO L AUDIO R

AUDIO OUT

Notes

•Set the aspect ratio using ASPECT in the INPUT

SETTING menu according to the input signal.

•When you connect the unit to 15k RGB/component

video equipment, select RGB or component with the

INPUT-A setting in the SET SETTING menu.

•Use the composite sync signal when you input the

external sync signal from 15k RGB/component

equipment.

Right side

15k RGB/Component equipment

to RGB/

component

output

SMF-402 Signal

Cable

(not supplied)

3X phono jack y

HD D-sub

15-pin (male)

Connecting with a VCR/15k RGB/

Component Equipment

This section describes how to connect the projector

with a VCR, external active speakers, and 15k RGB/

component equipment.

For details on how to connect a computer, see page 14

(GB).

Also refer to the instruction manuals of the equipment

to be connected.

When making connections, be sure to:

•turn off all equipment before making any

connections.

•use the proper cables for each connection.

•insert the plugs of the cables properly; plugs that are

not fully inserted often generate noise. When pulling

out a cable, be sure to pull it out from the plug, not

the cable itself.

S-Video cable

(not supplied)

Audio/video

cable

(supplied)

Active speakers

to audio/video

outputs

1)

to S video

output

1)

VCR

Right side

1) When both the S VIDEO and VIDEO jacks are connected to

the external equipment, the input signal from the S VIDEO jack is

selected.

Stereo audio

connecting

cable

(not

supplied)

Connecting

to

audio

output

17 (GB)

1 After all equipment is connected completely, plug

the AC power cord into the wall outlet.

The ON/STANDBY indicator lights in red and the

projector goes into the standby mode.

2 Press the I /

1

key on the Remote Commander or

on the control panel.

The ON/STANDBY indicator lights in green.

3 Turn on equipment connected to the projector.

Press the INPUT key on the Remote Commander

or on the control panel to select the input source.

Projecting

Rear remote

control detector

ON/STANDBY

indicator

APA key

INPUT-A:Selects audio and video signals input

from the INPUT A connector.

VIDEO: Selects audio and video signals input

from the video/audio input connector.

(If you connect to both the S VIDEO

and VIDEO jacks, the signal from the

S VIDEO jack is selected.)

4 Turn the zoom ring to adjust the size of the

picture.

5 Turn the focus ring to adjust the focus.

Note

Looking into the lens when projecting may cause

injury to your eyes.

To Press

Adjust the volume the VOLUME +/– keys on the control panel or

on the Remoter Commander.

Cut off the sound the AUDIO MUTING key on the Remote

Commander. To restore the sound, press the

AUDIO MUTING key again or press the

VOLUME + key.

Cut off the picture the PICTURE MUTING key on the Remote

Commander. To restore the picture, press the

PICTURE MUTING key again.

To get the clearest picture

You can get the suitable picture when a signal from

the computer is input. Press the APA key on the

Remote Commander or on the control panel.

The picture is automatically adjusted to be projected

clearest.

Notes

•Adjust the signal when the still picture is displayed

on the screen.

•If you switch the input signal or re-connect a

computer, press the APA key again to get the

suitable picture.

•“ADJUSTING” appears on the screen. Press the

APA key again during the adjustment to restore the

original screen.

•“Complete!” appears on the screen when the picture

is adjusted properly. The picture may not be adjusted

properly depending on the kinds of input signals.

•Adjust DOT PHASE in the INPUT SETTING menu

when you adjust the picture manually.

For details on DOT PHASE, see page 21 (GB).

Projecting

COMMAND

MUTING

I / 1

INPUT

APA

MENU

LASER

ENTER

RESET

VOLUME

R CLICK

PICTUREAUDIO

ONOFF

APA

VOLUME

INPUT

MENU

ENTER

RESET

ON

/STANDBY

POWER

SAVING

TEMP

/FAN

LAMP

/COVER

5

4

1

2

3

2

3

18 (GB)

To turn off the power

1 Press the I /

1

key on the Remote Commander or

on the control panel.

The following message appears to confirm if you

want to turn off the power.

POWER OFF?

Please press key again.

I / u

Note

The message will disappear if you press any key

except the I /

1

key, or if you do not press any

key for five seconds.

2 Press the I /

1

key on the Remote Commander or

on the control panel again.

The ON/STANDBY indicator flashes in green and

the fan continues to run for about 90 seconds to

reduce the internal heat. Also, the ON/STANDBY

indicator flashes quickly for the first 30 seconds.

During this time, you will not be able to turn the

power back on with the I /

1

key.

3 Unplug the AC power cord from the wall outlet

after the fan stops running and the ON/STANDBY

indicator lights in red.

When you cannot confirm the on-screen

message

When you cannot confirm the on-screen message in a

certain condition, you can turn off the power by

holding the I /

1

key on the Remote Commander or

on the control panel for about one second.

Note

Do not unplug the AC power cord while the

fan is still running; otherwise, the fan will

stop although the internal heat is still high,

leading to breakdown of the projector.

Projecting

19 (GB)

Using the MENU

The projector is equipped with an on-screen menu for

making various adjustments and settings.

To select the language used in the menu, see page

23 (GB).

1 Press the MENU key.

The menu display appears.

The menu presently selected is highlighted in

blue.

INPUT–A

PICTURE CTRL

CONTRAST : 8 0

BRIGHT : 50

GAMMA MODE:GRAPHICS

COLOR TEMP :HIGH

2 Use the M or m key to select a menu, then press

the , or ENTER key.

The selected menu appears.

INPUT–A

SET SETT ING

STATUS:ON

LANGUAGE : ENGL I SH

SPEAKER:ON

POWER SAVI NG:OFF

S I RCS RECE I VER: FRONT&REAR

INPUT–A : RGB

3 Make setting or adjustment on an item.

For details on setting individual items, see the relevant

menu pages.

To clear the menu display

Press the MENU key.

The menu display disappears automatically if no key

is pressed for one minute.

To reset items that have been adjusted

Press the RESET key.

“Complete!” appears on the screen and the settings

appearing on the screen will be reset to their factory

preset values.

Items which can be reset are:

•“CONTRAST”, “BRIGHT”, “COLOR”, “HUE”,

and “SHARP” in the PICTURE CTRL menu

•“DOT PHASE”, “SIZE”, and “SHIFT” in the

INPUT SETTING menu.

Adjustments and settings using the menu

Menus Setting items

About the memory of the settings

The settings are automatically stored in the projector

memory.

When no signal is input

When there is no input signal, “NO INPUT–Cannot

adjust this item.” appears on the screen, and each item

cannot be adjusted.

The PICTURE CTRL

Menu

The PICTURE CTRL (control) menu is used for

adjusting the picture.

Unadjustable items depending on the input signal are

not displayed in the menu.

Operation

1. Select an item

Use the M or m key to select the item, then press the

, or ENTER key.

2. Adjust an item

• When changing the adjustment level:

To increase the number, press the M or , key.

When the video signal is input

When the RGB signal is input

VIDEO

PICTURE CTRL

CONTRAST : 80

BRIGHT : 50

COLOR : 50

HUE : 50

SHARP : 50

D.PICTURE:OFF

COLOR TEMP : LOW

COLOR SYS :AUTO

INPUT–A

PICTURE CTRL

CONTRAST : 80

BRIGHT : 50

GAMMA MODE :GRAPH I CS

COLOR TEMP : H I GH

Using the MENU / The PICTURE CTRL Menu

(Continued)

20 (GB)

(NTSC3.58/

4.43 only)

To decrease the number, press the m or < key.

Press the ENTER key to restore the original screen.

• When changing the setting:

Press the M or m key to change the setting.

Press the ENTER or < key to restore the original

screen.

CONTRAST

Adjusts the picture contrast.

The higher the setting, the greater the contrast.

The lower the setting, the lower the contrast.

BRIGHT

Adjusts the picture brightness.

The higher the setting, the brighter the picture.

The lower the setting, the darker the picture.

COLOR

Adjusts color intensity.

The higher the setting, the greater the intensity.

The lower the setting, the lower the intensity.

HUE

Adjusts color tones.

The higher the setting, the picture becomes greenish.

The lower the setting, the picture becomes purplish.

SHARP

Adjusts the picture sharpness.

The higher the setting, the sharper the picture.

The lower the setting, the softer the picture.

D. (Dynamic) PICTURE

Emphasizes the black color.

ON: Emphasizes the black color to produce a bolder

“dynamic” picture.

OFF: Reproduces the dark portions of the picture

accurately, in accordance with the source signal.

GAMMA MODE

Selects a gamma correction curve.

GRAPHICS: Improves the reproduction of half

tones. Photos can be reproduced in natural tones.

TEXT: Contrasts black and white. Suitable for

images that contains lots of text.

COLOR TEMP

Adjusts the color temperature.

HIGH: Makes the white color bluish.

LOW: Makes the white color reddish.

COLOR SYS (System)

Selects the color system of the input signal.

Normally, set to AUTO.

If the picture is distorted or colorless, select the color

system according to the input signal.

Input signals and adjustable/setting items

Item Input signal

Video or Component RGB B&W

S video (Y/C)

CONTRAST

BRIGHT

COLOR ––

HUE

–––

SHARP –

D. PICTURE –

GAMMA MODE – – –

COLOR TEMP

COLOR SYS ––

: Adjustable/can be set

– : Not adjustable/can not be set

The PICTURE CTRL Menu

La page charge ...

Sony VPL-PX1 Manuel utilisateur

Sony VPL-PX1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents