weBoost Home Room U652020 Guide d'installation

FRANÇAIS

ENGLISH

Installation Guide

Cell Signal Booster

Home Room

A WILSON ELECTRONICS BRAND

NEED HELP?

weboost.ca 866.294.1660

Package Contents 1

Preparation 2

STEP 1-A & B: Connect Inside Antenna To Booster 3

STEP 2-A: Point Outside Antenna Toward Nearest Cell Tower 4

STEP 2-B: Mount Bracket To Outside Antenna 5

STEP 3: Route & Connect Cable To System 7

STEP 4: Power Up The Booster & Optimize System 8

Measuring Booster Performance 10

Light Patterns 12

Troubleshooting 13

Safety Guidelines 14

Speciﬁcations 17

Warranty 18

______

Index

1

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Package

Contents

Home

Room

Inside

Antenna

Outside

Antenna

Cable

Connector

Window

Entry Cable

Roof/Pole

Mount

Bracket

Wall Mount

Bracket

Power

Supply

30' Cables

Qty. 2

2

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Preparation

You Will Need (tools not included)

Make sure the following materials are prepared and ready for your

installation.

o Ladder

o Phillips-head screwdriver

o 10mm open-end wrench or adjustable wrench

o Drill (if routing cable through wall)

o 1.25”-2” diameter pole existing pole (or order #901117)

o Recommended: Power Strip with surge protection

1 to 2 hours

2 people (a person to help with antenna calibration)

3

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

NOTE: Do not connect booster to power until the system is fully installed.

______

Step 1-A & B: Connect Inside

Antenna To Booster

Connect Inside Antenna cable to the bottom port on Home Room booster

labeled ‘INSIDE’ and place Inside Antenna in weak signal area at least 18

inches away from booster.

Inside

Antenna

Booster

4

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Step 2-A: Point Outside

Antenna Toward Nearest

Cell Tower

Point the Outside Antenna toward the nearest cell phone tower. To ﬁnd the

nearest tower, use an app such as ‘Open Signal’. After locating a cell tower’s

aproximate locationThis is the most critical step of the installation process

because it will determine the overall performance of the booster system.

Cell Tower

Outside Antenna

NOTE: The Outside Antenna must be at least

20 feet horizontal or 50 feet vertical from the Inside

Antenna for best performance. Make sure the Inside

Antenna and Outside Antennas are setup so they are

facing away from each other.

f

a

c

i

n

g

a

w

a

y

5

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Step 2-B: Mount Bracket To

Outside Antenna

Pole Mounting and Wall Mounting Options are included. The pole mounting

option is preferred because it would be easier to adjust to the direction

of the cell tower.

Attach the L-Bracket to the Outside Antenna and use the U-Bolts/Pole

Bracket to attach the L-Bracket to a pole.

NOTE: Mounting on existing roof exhaust pipe would

be a good time-saver option.

Cell Tower

Outside Antenna

Pole

(1.25”-2.0”dia.)

U-bolt &

Pole Bracket

L-Bracket

Pole Mounting Option

6

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

(STEP 2-B cont.)

Drill holes using

3/16 inch bit

Tap anchors in

Fasten bracket to back

of Outside Antenna

Secure bracket to wall

mounting

Outside Antenna

on wall bracket

sideview

Wall Mounting Option

7

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Step 3: Route & Connect

Cable To System

Connect the white RG-6 Cable to Outside Antenna and route cable

into the home. All connections should be hand tightened only.

A Window Entry Cable is provided to help make cable entry easier. Route

cable to the Home Room booster and connect to top port

labeled ‘OUTSIDE’.

Outside

Antenna

Inside

Antenna

Outside

Antenna

Cell

Tower

Inside

Antenna

RG-6 Cable

Window

Entry Cable

Booster

Window Entry Cable

Booster

8

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Step 4: Power Up The

Booster & Optimize the

System

5

0

F

E

T

H

O

R

I

Z

O

N

T

A

L

O

R

2

0

F

E

T

V

E

R

T

I

C

A

L

D

I

S

T

A

N

C

E

5

0

F

E

T

H

O

R

I

Z

O

N

T

A

L

O

R

2

0

F

E

T

V

E

R

T

I

C

A

L

D

I

S

T

A

N

C

E

Plug the Power Supply into wall outlet then connect to Home Room Booster.

Outside

Antenna

Outside

Antenna

Cell

Tower

Inside

Antenna

RG-6 Cable

Window

Entry Cable

Booster

to power

Inside

Antenna

Power Supply

Window Entry Cable

50 FEET HORIZONTAL OR 20 FEET

VERTICAL DISTANCE

Booster

9

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

After powering up your system, you are now ready to optimize your system.

Rotate the outside antenna in 1/4 turn increments (within the cell towers

general location) and each time observing the signal level on your cell

phone from the inside antenna’s projected area.

______

(STEP 4 cont.)

after each rotation, observe signal level

on your cell phone from the inside

antenna’s projected area

10

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Measuring Booster

Performance

Settings > About Phone > Status or Network > Signal Strength or

Network Type and Strength (exact options/wording depends on

phone model).

Android™

iPhone is a registered trademark of Apple Inc. Android is a trademark of Google Inc.

iOS 11 and later no longer displays the decibel (dBm) reading

in ‘Field Test Mode’. Tip: Using the signal bars and performing

data speed tests on your cell phone can assist you in ﬁnding

the strongest signal direction as well as placing calls in dierent

locations. For changes/updates on this issue, periodically go to

weboost.ca/signalstrength.

iPhone®

How To Get Signal Strength As A Number

All Other Phones & Alternate Methods

Go to www.weboost.ca/test-mode-instructions/

11

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

EXCELLENT GOOD FAIR POOR DEAD ZONE

3G/1x

4G/LTE

-70dBm

-90dBm

-71 to -85dBm

-91 to -105dBm

-86 to -100dBm

-106 to -110dBm

-101 to -109dBm

-111 to -119dBm

-110dBm

-120dBm

SIGNAL

STRENGTH

EXCELLENT GOOD FAIR POOR DEAD ZONE

3G/1x

4G/LTE

-70dBm

-90dBm

-71 to -85dBm

-91 to -105dBm

-86 to -100dBm

-106 to -110dBm

-101 to -109dBm

-111 to -119dBm

-110dBm

-120dBm

SIGNAL

STRENGTH

Having an accurate measurement of signal strength in decibels (dBm) is crucial when

installing your system. Decibels accurately measure the signal strength you are receiving.

DID YOU KNOW a signal increase of just 3dB is 2

times the power and signal ampliﬁcation!

Compare Results

______

(MEASURING BOOSTER PERFORMANCE cont.)

Signal Strength without Booster

Note here:

Signal Strength with Booster

Note here:

12

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Light Patterns

Solid Green

This indicates that your booster is

functioning properly and there are no

issues with installation.

Blinking Green, Then Red

Band has reduced gain. This indicates that one or more of the booster bands has reduced

power due to a feedback loop condition called oscillation. This is a built in safety feature

to prevent harmful interference with a nearby cell tower. If you are already experiencing

the desired signal boost, then no further adjustments are necessary. If you are not

experiencing the desired boost in coverage then refer to the Troubleshooting section.

Solid Red

Band has shutoff. This is due to a feedback loop condition called oscillation.

This is a built in safety feature that causes a band to shut off to prevent harmful

interference with a nearby cell tower. Refer to Troubleshooting section.

Blinking Green, Orange

Band has reduced gain. This indicates that one or more of the booster bands has reduced

power due to overload from nearby cell tower. This is a built in safety feature to

prevent harmful interference with a nearby cell tower. If you are already experiencing

the desired signal boost, then no further adjustments are necessary. If you are not

experiencing the desired boost in coverage then refer to the Troubleshooting section.

Solid Orange

Band has shutoff due to overload from nearby cell tower. Outside Antenna must be

adjusted. Refer to Troubleshooting section.

Light O

If the Signal Booster’s light is off, verify your power supply has power.

13

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Troubleshooting

FIXING ANY RED LIGHT ISSUES

FIXING ANY ORANGE LIGHT ISSUES

1

2

3

Verify Outside Antenna faces away from the Inside Antenna. Un-plug and re-

plug in power supply.

Verify the Inside Antenna is at least 18” from the Booster and pointed away

from the Booster. Unplug and re-plug in power supply.

Tighten all cable connections (be sure to handtighten only, do NOT use tools).

You may want to undo and redo the connection completely. Unplug and re-

plug in power supply.

Increase the distance (horizontally or vertically) between the Outside and

Inside antenna. Add included cable if needed. Un-plug and re-plug in

power supply.

Outside Antenna must be adjusted. Wait 10 seconds between adjustments for

the lights to reset.

4

This involves Solid Red & Blinking Green/Red lights.

This involves Solid Orange & Blinking Green/Orange lights.

IF YOU ARE HAPPY WITH THE COVERAGE, THESE LIGHT ISSUES DON’T HAVE TO

BE RESOLVED. YOUR CARRIER’S BAND HAS NOT BEEN AFFECTED.

Pole Mount Option: Rotate the Outside Antenna away from the strongest

cellular signal in small increments (45°) until the light turns green. Unplug

and re-plug in power supply.

Wall Mount Option: Change mount location. Move the Outside Antenna

to a wall outside the building to see if the lights turn green. Un-plug and

re-plug in power supply.

14

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

______

Safety Guidelines

To uphold compliance with network protection standards, all active cellular devices

must maintain at least six feet of separation distance from Inside Panel and Dome

antennas and at least four feet of separation distance from desktop Antenna.

Use only the power supply provided in this package. Use of a non-weBoost product

may damage your equipment.

The Signal Booster unit is designed for use in an indoor, temperature-controlled

environment (less than 100 degrees Fahrenheit). It is not intended for use in attics or

similar locations subject to temperatures in excess of that range.

RF Safety Warning: Any antenna used with this device must be located at least 8

inches from all persons.

AWS Warning: The Outside Antenna must be installed no higher than 10 meters (31’9”)

above ground.

FOR MORE INFORMATION ON REQUIREMENTS SET OUT IN ISED CPC-2-1-05,

SEE BELOW:

http://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf08942.html

This is a CONSUMER device.

BEFORE USE, you MUST meet all requirements set out in CPC-2-1-05.

You MUST operate this device with approved antennas and cables as speciﬁed by the

manufacturer. Antennas MUST NOT be installed within 20 cm of any person.

You MUST cease operating this device immediately if requested by ISED or licensed

wireless service provider.

WARNING. E911 location information may not be provided or may be inaccurate for calls

served by using this device.

This device may operate in a ﬁxed location only, for in-building use.

15

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Antenna Kit Options

Outside antenna maximum permissible

antenna gain (dBi) 50

Inside antenna maximum permissible

antenna gain (dBi) 50

4.50 4.20

4.16

3.73

6.60

BAND 12/17

BAND 13 BAND 5

BAND 4

BAND 25/2

Ω

50

75

50

70

75

50

Antenna Type

4G Dome

Wall Mount Panel Antenna

RV Desktop Antenna

Coax Type

RG-174

Wilson-400

RG-58

RG-6

RG-11

Wilson-400

RG-58

RG-6

RG-11

Wilson-400

RG-58

Kit #

304412-17410

304412-40010

304412-5810

304419-0610

304419-1110

311135-40060

311135-5820

311155-0630

311155-1150

311155-40060

311160

Ln(ft)

10

60

20

30

50

60

13

FIXED INSIDE ANTENNA KIT OPTIONS

3.71

4.92

This radio transmitter 4726A-460020 has been approved by Innovation, Science and

Economic Development Canada to operate with the antenna types listed below, with the

maximum permissible gain indicated. Antenna types not included in this list that have a

gain greater than the maximum gain indicated for any type listed are strictly prohibited for

use with this device.

4.90

3.49

16

CELL PHONE SIGNAL BOOSTER HOME ROOM

ENGLISH

Ω

75

50

75

50

75

50

75

50

75

Antenna Type

Yagi Directional

4G Omni

Omni-Directional

Wide Band Directional

Pole Mount Panel

Wide Band Directional

Coax Type

RG-6

RG-58

RG-11

Wilson-400

RG-11

RG-6

Wilson-400

RG-58

RG-11

RG-58

RG-174

Wilson-400

RG-58

Wilson-400

RG-58

Wilson-400

RG-6

RG-11

RG-6

RG-11

Kit #

301111-0675

301111-5850

301111-11140

301111-400170

304421-1120

304421-0610

304422-40020

304422-5810

304422-1120

304421-5810

304421-17410

311203-40020

311203-5820

314411-40075

314411-5825

314453-5825

314453-40075

314473-0640

314473-1175

314475-0630

314475-1175

Ln(ft)

75

50

140

170

20

10

20

10

20

10

20

75

25

75

40

75

30

75

FIXED OUTSIDE ANTENNA KIT OPTIONS

______

(ANTENNA KIT OPTIONS cont.)

17

HOME ROOM CELL PHONE SIGNAL BOOSTER

ENGLISH

______

Speciﬁcations

Home Room™

Product Number U652020

Model Number 460020

IC IC: 4726A-460020

Connectors SMA-Female on the Inside Antenna / F-Female on the Outside Antenna

Antenna Impedance 50 Ohms / 75 Ohms

Frequency 698-716 MHz, 746-787 MHz, 824-894 MHz, 1850-1995 MHz, 1710-1755/2110-2155 MHz

Power output for single cell phone

(Uplink) dBm

700 MHz

Band17

700 MHz

Band13

800 MHz

Band 5

1700 MHz

Band 4

1900 MHz

Band 2

23.94 24.19 23.49 24.55 23.61

Power output for single cell phone

(Downlink) dBm

700 MHz Band17

Band17

700 MHz Band13

Band13

800 MHz

Band 5

2100 MHz

Band 4

1900 MHz

Band 2

11.64 11.92 12.1 11.9 9.5

Noise Figure 5 dB nominal

Isolation > 110 dB

Power Requirements AC / DC 5V, 4A, w/2.5x5.5mm Jack

The term “IC” before the radio certiﬁcation number only signiﬁes that Industry Canada technical

speciﬁcations were met.

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device

may not cause interference, and (2)) This device must accept any interference, including interference that may

cause undesired operation of the device. Changes or modiﬁcations not expressly approved by weBoost could

void the authority to operate this equipment.

3301 East Deseret Drive, St. George, UT

866.294.1660

www.weboost.ca

weBoost products covered by U.S. patent(s) and pending application(s)

For patents go to: weboost.com/us/patents

NOT AFFILIATED WITH WILSON ANTENNA

2 YEAR WARRANTY

weBoost Signal Boosters are warranted for two (2) years against defects in

workmanship and/or materials. Warranty cases may be resolved by returning the

product directly to the reseller with a dated proof of purchase.

Signal Boosters may also be returned directly to the manufacturer at the

consumer’s expense, with a dated proof of purchase and a Returned Material

Authorization (RMA) number supplied by weoost. weBoost shall, at its option,

either repair or replace the product.

This warranty does not apply to any Signal Boosters determined by weBoost

to have been subjected to misuse, abuse, neglect, or mishandling that alters or

damages physical or electronic properties.

Replacement products may include refurbished weBoost products that have been

recertified to conform with product specifications.

RMA numbers may be obtained by contacting Customer Support

DISCLAIMER: The information provided by weBoost is believed to be complete

and accurate. However, no responsibility is assumed by weBoost for any business

or personal losses arising from its use, or for any infringements of patents or other

rights of third parties that may result from its use.

La page charge ...

weBoost Home Room U652020 Guide d'installation

Ce manuel convient également à

weBoost Home Room U652020 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents