Warmup 3iE Energy Monitoring Thermostat Manuel utilisateur

INSTALLATION AND

OPERATION MANUAL

MANUEL D’INSTALLATION ET DE

PROGRAMMATION

Warmup® 3iE™

Energy-Monitoring

Thermostat

Ecoénergétique

24/7 Technical Hotline

Canada (888) 592-7687 - USA (888) 927-6333

Buy at www.FlooringSupplyShop.com

2

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

CONTENTS

Introduction Page 3

Getting started Page 4

Setting your programs Page 5

View and edit a schedule Page 8

Holiday mode Page 9

Energy monitor Page 10

Settings Page 12

Setting heating target Page 14

Advanced settings Page 15

Setting your heating system Page 16

Probes Page 17

Warranty Page 18

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

3

Your thermostat’s default screen is the Home Screen. This screen

displays important information such as the time, current floor and

air temperature as well as the target set temperature. From this page

you can either access the “MENU” page (press “menu”) or override

the current program (press “ ” or “ ”).

When using the 3IE thermostat there are some simple rules to keep

in mind:

1. Pressing “ ” allows you to confirm your selection

2. Pressing “ ” takes you back to a previous page in the menu

sequence

3. Pressing the “ ” and “ ” buttons allow you to change the

setting which is highlighted

4. Pressing an illuminated button in this group will allow you to highlight another setting to edit

5. Pressing an illuminated button in this group will allow you to select another option in the menu

6. When this light is illuminated it indicates that power is being directed to the heating systems (can be

turned off).

If you do not press any button on the thermostat for 1 minute, then it will go to standby mode. In standby

mode the screen will be dimmed but the thermostat will continue to function as normal. To exit standby

mode press “wake” ( ).

The button on bottom of the 3IE (button 7) is the power button. You can turn off your thermostat and

your Warmup floor heating system by holding down this button for 3 seconds. You can turn it on again by

holding it down for another 3 seconds.

INTRODUCTION

GROUND FAULT CIRCUIT INTERRUPTER

The GFCI feature is used to detect any leakage of current from your heating system. During a ground fault

the two lines of the load will be cut off. Once your thermostat is installed and connected to a power supply

you can test the GFCI function by increasing the set temperature until heating is on - the red light in the

top corner must be illuminated - and pressing the “TEST” button (see 8).

If your test is successful you will see the GROUND FAULT screen and you will need to hold “cancel” for 3

seconds in order to restore heating operation.

TE

ST

4

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

GETTING STARTED

1. Language

2. Time perefrences and settings

3. Date preference and settings

4. Daylight savings

5. Temperature preferences

6. Theme

7. Brightness

8. Standby Brightness

9. Heating LED

10. Audio Feedback

11. Floor type

12. Set heating target

13. Program schedule

14. Set energy monitor

15. (You may skip this section and

complete at a later date )

16. Energy settings

On initial power up the thermostat will guide you through set up procedure.

By accessing the main menu you can program your thermostat or make any changes to the thermostat

settings. To access the menu press “menu” on the main screen.

If the thermostat is in sleep mode press ”wake”.

LThe energy monitoring menu will be skipped automatically if a pre set program is selected on initial

setup.

GROUND FAULT CIRCUIT INTERRUPTER (cont’d)

However if the thermostat detects that one of the relays has FAILED to open correctly you will see the

Control Fault screen and the TEST LED will illuminate.

In the following circumstances you should immediately isolate the power supply to the thermostat and

contact Warmup customer service:

1. Press the TEST button when heating is on (the red light in the top corner is on) and the screen does

not display GROUND FAULT or cut power to the load.

2. The thermostat shows the GROUND FAULT screen during normal operation.

3. The thermostat shows the CONTROL FAULT screen.

Note: The GFCI test should be carried out monthly.

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

5

Press “ ” and “ ” to set the start time for the first of the

day.

If you want to change the target floor temperature press

“floor temp”, you can now press “up” and “down” to change

the target floor temperature.

If you want the target temperature to change later on in the

day then press “add another period”. You can add up to 10

periods in each day.

SETTING YOUR PROGRAM

Press “menu”, then Press “set program”.

You may have to press “wake” first, if the stat is in standby

mode.

Press the programming option that suits your needs.

• Set each day separately: set each day of the week with

a different program

• Set weekday and weekend: set a program for Monday –

Friday and a different program for Saturday and Sunday

• Set all days the same: one program is set for all the days

of the week

• Set fixed temperature: set a single temperature to be

held constantly

• Select a pre-set: see explanation in table

LIf you hold a button for several seconds it will scroll

continuously until you release your finger

72°F

next period

LIf you would rather use your thermostat to target

an air temperature then see page 12.

6

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

Once you have set all the desired periods in the day press

“OK” to go to the summary page.

This summary page allows you to see the program you have

set for this day. If you need to change something press

“edit”. This will take you back to the first period of the day.

Remember that you will need to add all the periods again.

If you are happy with the program and would like to set the

same program for the following day press “copy to …”

SETTING YOUR PROGRAM

LIt is recommended that you finish your daily program

on a low target temperature so that you save energy

overnight.

If you do not need the heating to protect against

frost then you can scroll down to the bottom of the

temperature range to set the target temperature to

“OFF”. With this setting the heating will not come on

regardless of the temperature.

If you are happy with the program but would like to set a

different program for the following day press “OK”

If you would like to return to the preceding day press “back”.

When you have set a program for all the days including

Sunday (or Weekend in the case of Weekday/Weekend) then

pressing “OK” will enter the schedule and return you to the

home screen.

LThe set temperature for the time before the first

period of the day comes from the night before.

104 F

86

68

50

- oor

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

7

SETTING YOUR PROGRAM

If you are using your 3IE thermostat in the bathroom, bedroom, kitchen or living room then the pre-set

schedules might help you set a program appropriate for you. Just select the desired pre-set room and

everything is done automatically.

PRE-SET PROGRAMS TABLE :

Bathroom Kitchen Bedroom Living room

Time Floor Temp Time Floor Temp Time Floor Temp Time Floor Temp

Monday

to Friday

06:00 72°F/ 25°C 06:00 73°F / 23°C 06:00 72°F / 25°C

08:00 50°F / 10°C 08:00 50°F /10°C 08:00 50°F /10°C

19:00 68°F / 20°C 18:00 73°F / 23°C 20:00 68°F / 20°C 18:00 73°F / 23°C

23:00 59°F / 15°C 22:00 50°F /10°C 23:00 50°F / 10°C 21:30 50°F / 10°C

Saturday -

Sunday

07:00 72°F / 25°C 07:00 73°F/23°C 06:00 72°F / 25°C 08:00 73°F / 23°C

11:00 64°F / 18°C 11:00 64°F /18°C 08:00 50°F / 10°C

18:00 68°F / 20°C 18:00 73°F/ 23°C 20:00 68°F / 20°C 18:00 68°F / 20°C

23:00 59°F / 15°C 22:00 50°F /10°C 23:00 50°F / 10°C 20:00 50°F / 10°C

LIf you have used a pre-set schedule but want to make some changes just use the edit schedule

function explained in the “View and Edit a Schedule” section.

8

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

If you would like to view or edit the time and temperature

settings of each day then press “view / edit program”.

Press “up” and “down” until the day that you would like to

view is highlighted, then press “OK” to view that day.

To exit the “VIEW / EDIT PROGRAM” menu, press “back”.

Note that if you have edited any days these changes will be

saved.

Here you can see review the heating schedule for the

selected day.

If you would like to change any of the heating periods press

“edit”. Remember that you will have to set all the heating

periods. You can view the schedule for the following day by

pressing “view …”.

To return to the day selection, press “OK”.

VIEW AND EDIT A SCHEDULE

L If you want to change the settings of multiple days it

might be easier to set a new program using the “set

program” option

104 F

86

68

50

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

9

HOLIDAY MODE allows you to over-ride your schedule with

a fixed temperature for a prolonged period of time. This

can help save energy if you know that you will be out of the

house and only want minimal heating.

Press the highlighted button next to “holiday”.

Press “up” and “down” to set the first day you would like the

HOLIDAY MODE to start.

Press “holiday end at” and then press “up” and “down” to

set the day when you would like holiday mode to stop. At

the end of the HOLIDAY MODE your program will return to

the current settings. If you would like HOLIDAY MODE to

continue indefinitely, leave the end date on “not specified”.

Press “holiday temperature” to set the fixed temperature

that will be held for the entire HOLIDAY MODE period.

Pressing “OK” will confirm the selection and HOLIDAY MODE

will start at 12:00 pm on the specified date.

During the HOLIDAY MODE you will have a modified home

screen. To cancel the HOLIDAY MODE at any time just press

“cancel”.

If you want to return to HOLIDAY MODE you will need to set

it again.

HOLIDAY MODE

5

5F

2011

50 F

F

10

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

ENERGY MONITOR

Your thermostat monitors the amount of energy your floor

heating system is using, you can use these pages to view the

amount of energy used and set parameters to estimate the

cost of that energy.

If you want to see how much energy you have used then

select “view energy use” and then select the time period you

would like to review.

* If you see the “load settings” option you will need to enter

the total power in watts of the floor heating system connect

to the thermostat. If you are unclear about the power of your

floor heating then contact your installer.

After you press “view energy use”, you will need to select the

length of time in which you are interested.

On the graph each red bar indicates a time period (in this

case it is months). The height of the bar indicates that

amount of energy in KWH used by the floor heating system

during that period. The bar in the far right is the most recent

time period and the bar on the far left is the oldest.

The total amount of energy used in the entire time span is

displayed in the bottom bar.

Press “OK” to return to the ENERGY MONITOR menu.

L If you are interested in seeing how much energy you

can save by adjusting the settings of your thermostat,

then alter your heating program and wait a few days

before comparing the daily energy used before and

after you changed your program.

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

11

$

ENERGY MONITOR

If you want to view the estimated cost of your energy usage

then you will need to set the cost parameters in “energy

settings”. The cost estimate will only be accurate for the time

period AFTER you set the heating costs.

• Single energy tariff means that you have a single cost

of electricity all day long

• Standard / low energy tariff means that you have a

discounted cost of electricity during part of the day.

Select the appropriate structure that applies to your

electricity tariff plan.

For both the standard and low energy tariff you will need

to set a cost per Kilowatt hour (KWH). First set the relevant

currency by pressing “up” and “down” (you can select £, $, €

and Y). Press “ok” to proceed to the first digit of the energy

tariff, press “up” and “down” to select the correct amount

and then press “ok” to proceed to the second digit. Continue

pressing “ok” until you have set all the digits and returned to

the ENERGY MONITOR main page.

If you are setting a “standard/ low energy tariff” you will also

need to set the time of day at which the low energy tariff

starts and stops and the cost per KWH during the low tariff

period.

After all these parameters are set you can view the cost of

the energy used by your floor heating system in “view cost

estimate”. If you are using “standard / low energy tariff”

then the amount/ cost of energy used in the standard period

will be displayed in red and the amount/ cost used in the low

period will be displayed in white.

L If your energy cost is 11.6 cents per KWH then you will

need to set it to $0.116.

12

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

Your 3IE is a very flexible device and be configured in many

different ways to meet your requirements.

Functions that can be accessed in the “settings” menu

include:

Time

• Settimeanddate

• Set time format preference (12Hr clock or 24Hr

clock and date format preference (MM/DD/YYYY or

DD/MM/YYY)

• Turnonautomaticday-lightsavingsforyourregion

Language

• Selectthelanguageofoperations

Temperature preferences

• Selecttemperatureunitpreference(°Cor°F)

Display / audio

• Choosehomescreenthemeandsetscreenbrightness

• Turnon/offheatingLEDandaudiofeedback

• Turnon/offchildlock(detailsontheoppositepage)

Set heating target

• Select if your thermostat uses floor temperature

sensor or air temperature sensor for thermal regulation

(details : see page 14)

Advanced settings

WARNING!! The options in this section can affect the

performance of your thermostat and should only be

modified by an experienced floor heating installer or

under the instruction of Warmup technical support.

SETTINGS

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

13

SETTINGS

Theme

• Change the content and style of home screen and

standby screen

Standby brightness

• Setthe brightness of the LCDscreeninstandbymode

between 0 (dimmest) and 5 (brightest)

Note: when set to 0 the LCD screen will turn OFF and

the “wake” LED will not be illuminated. You will need to

remember that you turn the screen on by pressing

Display brightness

• SetthebrightnessoftheLCDscreeninnormaloperation

between 1 (dimmest) and 6 (brightest)

Heating indication

• Thisfeatureallowsyoutoturnofftheheatingindication

LED (top right of the LCD screen). The thermostat will

continue to operate as normal but the LED will not turn

on to indicate when heating has started and stopped.

Audio feedback

• Thisfeatureallowsyoutoturnoffthebeepsoundmade

when a button is pressed

Child lock

• Childlockcreatesadelaybetweenpressing“wake”and

exiting the standby mode. When child lock is on you will

need to hold “wake” continuously for 10 seconds in order

to exit standby mode.

14

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

Your thermostat is capable of using a floor temperature

sensor, air temperature sensor or both for thermal regulation.

If you are using your floor heating as secondary heating

source (such as in the bathroom) then you might prefer to

use the floor temperature. However if the floor heating is the

primary heating source in your home you might prefer to use

the air temperature.

Set floor temperature

• The thermostat will use the temperature reading from

the floor sensor to decide whether heating is required to

achieve the target set temperature

Set floor temperature with air limit

• Thermostat will use the temperature reading from the

floor sensor to decide whether heating is required to

achieve the target set temperature, however if the air

temperature goes above the set limit then heating will

be suspended until air temperature falls below limit.

Set air temperature

• Thermostat will use the temperature reading from

the air sensor (inside thermostat housing) to decide

whether heating is required to achieve the target set

temperature.

SETTING HEATING TARGET

Start

L Hint: if you change the heating target settings then it is

advisable to re-program your thermostat to ensure that

the program still meets your needs

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

15

WARNING!!

The options in this section can affect the performance of your thermostat and should only be modified by

an experienced floor heating installer or under the instruction of Warmup technical support.

ADVANCED SETTINGS

Programmable Limit Overheat

Limit

Air Floor

Min Max Min Max

Tiles 41°F / 5°C 86°F / 30°C 41°F / 5°C 104°F / 40°C 104°F / 40°C

Stone 41°F / 5°C 86°F / 30°C 41°F / 5°C 104°F / 40°C 104°F / 40°C

Laminate 41°F / 5°C 81°F / 27°C 41°F / 5°C 81°F / 27°C 86°F / 30°C

Wood 41°F / 5°C 81°F / 27°C 41°F / 5°C 81°F / 27°C 86°F / 30°C

Carpet 41°F / 5°C 81°F / 27°C 41°F / 5°C 81°F / 27°C 86°F / 30°C

Vinyl 41°F / 5°C 81°F / 27°C 41°F / 5°C 81°F / 27°C 86°F / 30°C

User Deﬁned User Defined User Defined User Defined

16

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

SETTING YOUR HEATING SYSTEM

Floor type

This setting will affect the upper and lower limits of

programmable set temperatures as well as the overheat limit.

If you set a user defined limit then you are advised to check

the safe temperature limits with the flooring manufacturer

Master/ relay

This feature allows you to use one thermostat to control

another. This is useful if you need to control multiple floor

heating elements with one program. In order to set-up this

feature use the following steps:

1. Choose which thermostat will be the “master” and

which will be the “relay”.

2. Use low voltage electric cable to connect terminal 3 on

the “master” to terminal 3 on the “relay”.

3. Use low voltage electric cable to connect terminal 2 on

the “master” to terminal 2 on the “relay”.

4. In advanced settings of each thermostat switch the

“master” thermostat to master mode and the “relay”

thermostat to relay mode.

5. Program desired schedule into the “master”

thermostat. The “relay” thermostat will no longer use

its sensors for thermal regulation. It will now turn on/

off in tandem with the “master” thermostat.

LOn the “master” thermostat these connector cables

are in addition to the floor sensor but on the “relay”

thermostat the floor sensor is not necessary.

953

AM

953

AM

09:32 tues 23 jul 09

21.0°c target

20.5°c

ﬂoor

16.5°c out

19.0°c air

wake

tues 23 jul 09

21.0°c target

20.5°c

ﬂoor

14:22

wake

program

holiday

mode

advanced

sengs

energy

monitor

sengs

OPTIONS

ok

program

holiday

mode

advanced

sengs

energy

monitor

sengs

period: 1

day: all

add another

period

start me

08:00

ﬂoor temp

22.0°C

air limit temp

22.0°C

PROGRAM

ok cancel

SUMMARY all days

ok cancel - air

- ﬂoor - air

- ﬂoor

COST july

ok

0

1

2 £

std = £10.54 : low = £16.28

LANGUAGE

english

francais

deutsch

espanol

portugese

cancel up downok

09:32 tues 23 jul 09

20.5°c

ﬂoor

temporary override

unl 20:00

cancel

21.0°c target

MASTER/RELAY

oﬀ

master

relay

19.0°c ﬂoor

21.5°c target

19.0°c ﬂoor

21.5°c target

wake

tues 23 jul 11

ok

OPTIONS tues 23 jul 09

21.0°c target

20.5°c

ﬂoor

21.0°c target

20.5°c

ﬂoor

09:32 tues 23 jul 09

16.5°c out

19.0°c air

16.5°c out

19.0°c air

16.5°c out

19.0°c air

tues 23 jul 09

wake

09:32 tues 23 jul 09

wake

16.5°c out

19.0°c air

14:22

wakewake

19.0°c ﬂoor

21.5°c target

16.5°c out

19.0°c air

19.0°c ﬂoor

21.5°c target

16.5°c out

19.0°c air

wake

hours

0 12 24

10

20

30

40°C

program

holiday

mode

advanced

sengs

energy

monitor

sengs

OPTIONS tues 23 jul 09

09:32 tues 23 jul 11

72°F target

60.0°F out

66.0°F air

wake

09:32 tues 23 jul 11

wake

cancel up downok

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

17

Reset

PROBES

External sensor

You are able to attach a second sensor to terminals 2 and 3.

You can then use external sensor function to define the use of

that sensor:

1. External sensor: This is to be used when you can locate

the external sensor outside of the heated environment.

When this setting is selected it will display the external

temperature on the home screen and engage weather

compensation. Weather compensation saves energy by

delaying the start of heating period by 10 minutes if the

difference between internal and external temperature is

less than 41°F.

2. 2nd floor sensor: This is to be used if the floor surface area is very large and delicate to overheating.

The reading from this secondary floor sensor will be used to monitor the overheat limit.

Probe specification

If you have already installed a sensor which was not supplied by Warmup then you can use this setting to

allow your thermostat to function. The possible options are NTC 10K (standard probe supplied by Warmup

with the 3IE), NTC 12K (probe supplied by Warmup with previous models of thermostat) and NTC 15K. Note

that all thermostats are different and Warmup can only validate the thermostat’s performance when used

with a Warmup probe supplied for use with the 3IE.

Offset

In order to improve temperature reading accuracy this feature allows you to bias each sensor’s temperature

reading up or down by 41°F.

Reset

Reset will restore all software settings to the factory specified defaults.

LIf you are experiencing problems with your thermostat then you can perform a system reset by

holding the button the rear of the front module for 10 seconds.

18

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

WARRANTY

Warmup Inc warrants this product, to be free from defects in

the workmanship or materials, under normal use and service,

for a period of three (3) years from the date of purchase by

the consumer. If at any time during the warranty period the

product is determined to be defective, Warmup shall repair

or replace it, at Warmup’s option.

If the product is defective, please either,

(I) return it, with a bill of sale or other dated proof of

purchase, to the place from which you purchased it, or

(ii) contact Warmup. Warmup will determine whether the

product should be returned, or replaced.

This warranty does not cover removal or reinstallation costs,

and shall not apply if it is shown by Warmup that the defect

or malfunction was caused by damage which occurred while

the product was in the possession of a consumer.

Warmup’s sole responsibility shall be to repair or replace the

product within the terms stated above.

WARMUP SHALL NOT BE LIABLE FOR ANY LOSS OR

DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR

CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR

INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY,

EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS

PRODUCT. THIS WARRANTY IS THE ONLY EXPRESS

WARRANTY WARMUP MAKES ON THIS PRODUCT. THE

DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-

YEAR DURATION OF THIS WARRANTY.

This Warranty does not affect your statutory rights.

PLEASE REGISTER YOUR WARMUP PRODUCT AT:

www.warmup.com / www.warmup.ca

INSTALLATION

GUARANTEE

TM

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

19

CONTENU

Introduction Page 20

Premiers pas Page 21

Configuration des programmes Page 22

Programmes pré-définis Page 24

Voir et éditer un programme Page 25

Mode vacances Page 26

Contrôle de l’énergie Page 27

Réglages Page 29

Configurer la température cible Page 31

Paramètres avancés Page 32

Régler votre système chauffant Page 33

Sondes Page 34

Garantie Page 35

20

24/7 Technical hotline - Ligne d’assistance technique - Línea de asistencia técnica

US 1.888.927.6333 / CAN 1.888.592.7687

Lors de votre première utilisation du thermostat 3iE™,

familiarisez-vous avec ses six zones tactiles et son indicateur

LED lumineuse. Ils vont permettront de régler votre

thermostat et d’en modifier les paramètres. Les contrôles de

base sont les suivants :

1. La touche vous permet de valider une sélection.

2. Appuyez sur la touche pour annuler un réglage ou

pour retourner à l’écran précédent.

3. Grâce aux touches et vous pourrez augmenter et

diminuer les valeurs et/ou données.

4 et 5. Ces touches luminescentes vous permettent de

sélectionner l’option ou le paramètre que vous souhaitez

éditer.

6. Cette diode s’allume lorsque le système est en marche

ou actif.

7. Au bas de la façade du thermostat se trouve le bouton

d’alimentation. Pour mettre en marche ou éteindre

complètement le thermostat il suffit de presser ce

bouton pendant 3 secondes.

En outre, vous pouvez l’utiliser pour revenir à l’écran

d’accueil á tout moment.

Après une minute d’inactivité, l’écran du thermostat

s’assombrit puis se met en veille. En mode veille, le

thermostat continue de fonctionner normalement. Pour

désactiver ce mode, appuyez sur la touche “actif” ( ).

Sur l’écran d’accueil de votre thermostat, vous pourrez lire

des informations importantes telles que la date, l’heure, les

températures du sol et de l’air et aussi la température désirée.

A partir de cet écran, vous pouvez soit accéder au menu (en

appuyant sur “MENU”), soit passer outre le programme en

cours (en apputant sur “ “ ou “ “).

INTRODUCTION

LDans plusieurs des menus, vous trouverez l’option “aide”. Sélectionnez-la pour obtenir des

explications plus detaillées ou plus d’informations sur certaines fonctionnalités.

La page est en cours de chargement...

Warmup 3iE Energy Monitoring Thermostat Manuel utilisateur

Warmup 3iE Energy Monitoring Thermostat Manuel utilisateur

dans d''autres langues