dewert okin RF62 Remote Control Mode d'emploi

Marque
dewert okin
Modèle
RF62 Remote Control
Taper
Mode d'emploi
发行部门：研发部
创建时间：
2021-9-17
功能测试指导
创建人：
Gary
No：
Instruction of RF58 RF62
版本：
1.0
Page 1 of 4
1
Instruction of RF58 RF62
1
2
3
4
6
8
9
10
11
12
发行部门：研发部
创建时间：
2021-9-17
功能测试指导
创建人：
Gary
No：
Instruction of RF58 RF62
版本：
1.0
Page 2 of 4
2
3.2POSITION key test (Figure 2 Key 4)
Click this button, the display screen directly enters the motor control function interface
3.3 MEMORY Key Test (Figure 2 Key 6)
Press this button, and the screen displays the memory bit function
3.4 MASSAGE Button Test (Figure 2 Button 10)
Press this button to enter the massage function screen
3.5 UBB Key test (Figure 2 Key 12)
Click this button to turn on/off the underbed light
3.6 Flat Key Test (Figure 2 Key 2)
Click the button to enter the Flat interface, and the control box can be placed flat.
3.7 Back Key Test (Figure 2 Key 1)
Click the key to perform the functions displayed in the lower left corner of the display
3.8 Enter key test (Figure 2 Key 3 and Key 8)
Click this button to perform the functions displayed at the lower right corner of the display.
3.9 UP key test (Figure 2 Key 5)
Click this button to select up on the screen
发行部门：研发部
创建时间：
2021-9-17
功能测试指导
创建人：
Gary
No：
Instruction of RF58 RF62
版本：
1.0
Page 3 of 4
3
3.10 Down button test (Figure 2 Button 11)
Click the button, the interface downward selection function;
3.11 LEFT Button Test (Figure 2 Button 7)
Click the button to select the left side of the interface.
3.12 RIGHT Button test (Figure 2 Button 9)
Click this button to select the right side of the boundary.
FCC Statement：
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this de
vice may not cause harmful interference, and (2) this device must accept any interference received, including in
terference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s aut
hority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference i
n a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not instal
led and used in accordance with the instructions, may cause harmful interference to radio communications. Howe
ver, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and o
n, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Important Note:
发行部门：研发部
创建时间：
2021-9-17
功能测试指导
创建人：
Gary
No：
Instruction of RF58 RF62
版本：
1.0
Page 4 of 4
4
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated without restriction.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Statement
- English: This device complies with Industry Canada license‐exempt RSS standard(s).
Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This d
evice must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
‐ French: Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitationestautorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produ
ire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi le brouill
ageest susceptible d'encompromettre le fonctionnement.
This radio transmitter (ISED certification number: 25804-RF58) has been approved by Industry Canada to operate
with the antenna types listed with the maximum permissible gain indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this
device.
Le présent émetteur radio (ISED certification number: 25804-RF58) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal. Les types
d'antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont strictement
interdits pour l'exploitation de l'émetteur.
Radiation Exposure Statement
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated without restriction.
Déclaration d'exposition aux radiations
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé.
Cet équipement doit être installé et utilisé sans restriction.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

dewert okin RF62 Remote Control Mode d'emploi

Marque
dewert okin
Modèle
RF62 Remote Control
Taper
Mode d'emploi
Télécharger le PDF
rapport

dans d''autres langues

Autres documents