DCS BH1-30R-N Le manuel du propriétaire

US CA

Installation instructions

and User guide

Professional grill

30” BGC & BH1 models

Instructions d’installation

et Guide d’utilisation

Le gril professionnel

Modèles 30po BGC et BH1

1

Thank you for selecting this DCS Professional “BGC” Series Grill. Because of this appliance’s unique features we

have developed this manual. It contains valuable information on how to properly install, operate and maintain

your new appliance for years of safe and enjoyable cooking.

To help serve you better, please fill out and submit your Product Registration by visiting our website at www.

dcsappliances.com and selecting “Customer Care” on the home page and then select “Product

Registration”. In addition, keep this guide handy, as it will help answer questions that may arise as you use your

new appliance.

For your convenience, product questions can be answered by a DCS Customer Care Representative at

1-888-936-7872, or email: [email protected].

NOTE: Inspect the product to verify that there is no shipping damage. If any damage is detected, call the shipper

and initiate a damage claim. DCS by Fisher & Paykel is not responsible for shipping damage.

DO NOT discard any packing material (box, pallet, straps) until the unit has been inspected.

WARNING!

Do not try lighting this appliance without reading the “Lighting Instructions” section of this manual.

Improper installation, adjustment, alteration, service or maintenance can cause property damage,

injury or death. Read the installation, operating and maintenance instructions thoroughly before use,

installing or servicing this equipment. This outdoor cooking gas appliance is not intended to be in

-

stalled in or on recreational vehicles , boats or in a non-ventilated room. For outdoor use only.

WARNING

1

. Do Not store or use gasoline or any other flammable vapors and liquids in the vicinity of this

or any other appliance.

2.

An LP cylinder not connected for use shall not be stored in the vicinity of this or any other

appliance.

DANGER

If you smell gas:

1

. Shut off gas to the appliance.

2.

Extinguish any open flames.

3.

Open lid.

4.

If odor continues, keep away from the appliance and immediately call your gas supplier or

your fire department.

PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.

A MESSAGE TO OUR CUSTOMERS

NOTE: Please write the Model, Code, and Serial Numbers on this page for reference (can be found on the inside,

right side panel behind the drip pan handle. See page 23.)

MODEL NUMBER CODE SERIAL NUMBER

2

SAFETY PRACTICES & PRECAUTIONS 3-5

GRILL MODELS 6

INSTALLATION

Locating Grill / Built-in Clearances 7-9

Built-in Construction Details 10-11

Cart Assembly Instructions 12-15

Gas Hook-up 16-19

Leak Testing 20

Burner Adjustment 21

Radiant Assembly 22

Installer Checklist 23

USING THE GRILL

Lighting Instructions 24

Grilling 25-26

USING THE ROTISSERIE

SOME MODELS ONLY 2730

CARE & MAINTENANCE 3132

TROUBLESHOOTING 33

SERVICE 34

CONTENTS

3

IMPORTANT SAFETY NOTICE!

Certain Liquid Propane dealers may fill liquid propane cylinders for use in the grill beyond cylinder filling capacity.

This “Overfilling” may create a dangerous condition.

“Overfilled” tanks can build up excess pressure. As a safety device, the tank pressure relief valve will vent

propane gas vapor to relieve this excess pressure. This vapor is combustible and therefore can be ignited. To

reduce this danger, you should take the following safety precautions:

1.

When you have your tank filled, be sure you tell the supplier to fill it to no more than 3/4 (75%) of its total

capacity.

2

. If you own or use a spare tank, or have a disconnected tank, you should NEVER store

it near or under the grill/cart unit or heat box, or near any other ignition or heat

source. A metallic sticker with this warning is provided with the grill to remind you,

your family and all others who may use your grill of these safety

precautions. Install this sticker close to your barbeque grill.

3. Do not store a full tank in direct sunlight.

WARNING!

Do not try lighting this appliance without reading the “LIGHTING INSTRUCTIONS”

section of this manual. This grill is for outdoor use only.

WARNING!

Push and hold the igniter button, turn the selected burner knob to “SEAR”. If burner

does not light in 4 to 5 seconds turn knob “OFF” and wait 5 minutes before trying

again for any accumulated gas to dissipate.

WARNING: IMPORTANT!

Before each use, inspect the gas supply piping

or hose prior to turning the gas “on”. If there is

evidence of cuts, wear, or abrasion, it must be

replaced prior to use.

Never leave the appliance unattended during use.

n

Begin by insuring proper installation and servic-

ing. Follow the installation instructions within

this manual. Have your grill installed by a quali-

fied installer. Have the installer show you where

the gas supply shut-off valve is located so that

you know where and how to shut off the gas to

the grill. If you smell gas, your installer has not

done a proper job of checking for leaks. If the

connections are not perfectly sealed, you can have a small leak and therefore a faint gas smell. Finding a leak is

not a “do-it-yourself ” procedure. Some leaks can only be found with the burner control in the “ON” position and

this must be done by a qualified technician.

n

Children should not be left alone or unattended in an area where the grill is being used. Never allow them to sit,

stand or play on or around the grill at any time. When in use, portions of the grill get hot enough to cause severe

burns.

n

Do not store items of interest to children around or below the grill, in the cart or masonry enclosure. Never allow

children to crawl inside a cart or enclosure.

n

Never attach or disconnect an LP cylinder, or move or alter gas fittings when the grill is in operation or is hot.

n

Clean and perform general maintenance on the grill twice a year. Watch for corrosion, cracks, or insect activity.

Check the regulator, hoses, burner ports, air shutter, and venturi/valve section carefully. Always turn off gas at

the source (tank or supply line) prior to inspecting parts.

n

After a period of storage or non-use (such as over the winter), the gas grill should be checked for gas leaks, dete-

rioration, proper assembly, and burner obstructions before using.

SAFETY PRACTICES & PRECAUTIONS

• Always follow lighting instructions.

• Lid must be opened before lighting

the grill.

• Check for gas leaks before lighting.

• Never lean over an open grill when

lighting. Serious burns may result.

• Hot surfaces surrounding grill

grates could cause serious burns.

• Always leave at least 18" clearance

to combustibles around the grill.

• Never store a spare LP cylinder

under or near this unit.

• Never ll the tank beyond 3/4 full. A

re causing death or serious injury

may occur.

18”

WARNING

STICKER

4

For personal safety, wear proper apparel. Loose fitting garments or sleeves should never be worn while using

this appliance. Some synthetic fabrics are highly flammable and should not be worn while cooking. Only certain

types of glass, heat-proof glass ceramic, earthenware, or other glazed utensils are suitable for grill use. Use of

these types of materials may break with sudden temperature changes. Use only on low or medium heat settings

according to the manufacturer’s directions.

WARNING!

Spiders and insects can nest in the grill burners, causing the gas not to flow through the burner. The gas will flow

from the front of the burner into the control panel. This is a very dangerous condition which can cause a fire to occur

behind the valve panel, thereby damaging the grill components and making it unsafe to operate.

WARNING!

Keep the area surrounding the grill free from combustible materials, trash, or combustible fluids and vapors such as

gasoline or charcoal lighter fluid. Do not obstruct the flow of combustion and ventilation air.

WARNING!

Never use the grill in windy conditions. If located in a consistently windy area (oceanfront, mountaintop, etc.) a wind

break will be required. Always adhere to the specified clearances as defined in the “INSTALLATION” section of this

manual.

When using the side burners always use flat bottomed pans which are large enough to cover the side burner.

Adjust the flame so that it heats only the bottom of the pan to avoid ignition of clothing. Position handles inward

PREFERRED

AIR FLOW

GRILL EXHAUST

EXHAUST

FLAME

BURNER

Wind hitting the grill

while in use,

especially winds

blowing into or across

this hood gap, can

cause poor

performance and in

some cases can cause

the control panel and

knobs to get

dangerously hot.

WIND

GRILL PLACEMENT

n

Never let clothing, pot holders or other flammable materials come in contact with or get too close to any grate,

burner or hot surface until it has cooled. Fabric may ignite and result in personal injury.

n

Do not heat unopened food containers as a build-up of pressure may cause the container to burst.

n

Always use a covered hand when opening the grill lid and only do so slowly to allow heat and steam to escape.

n

Never lean over an open grill. When lighting a burner, always pay close attention to what you are doing. Be certain

you are pushing the control knob when you attempt to light the grill.

n

After lighting burners, make sure burners are operating normally (see page 21).

n

When using the grill, do not touch the grill burner, grate or immediate surrounding area as these areas become

extremely hot and could cause burns.

n

Grease is flammable. Never operate the grill without a grease tray. Let hot grease cool before attempting to

handle it. Avoid letting grease deposits collect in the drip pan. Clean often.

n

Do not use aluminum foil to line drip pans, grill grates or radiants. This can severely upset combustion air flow or

trap excessive heat in the control area. The result of this can be melted knobs or damaged ignition components.

n

Do not operate with a damaged cord or plug or after the appliance malfunctions or has been damaged in any man-

ner. Contact the manufacturer for repair.

n

Do not let the rotisserie motor cord hang over the edge of a table or touch hot surfaces.

n

Do not use an outdoor cooking appliance for purposes other than intended.

SAFETY PRACTICES & PRECAUTIONS

FLAME LIFT

WIND

PRIMARY

INTAKE

AIR FLOW

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill, with a

minimum

clearance of 3"

(7,6cm) (for

non-combusti-

bles) or 18"

(45,7cm) (for

combustibles)

from the back

WIND SCREEN

WIND

15” min.

(38,1cm)

EXHAUST VENT FLOW

3”

(7,6 cm) min.

for non-

combustibles

18” (45,7cm)

min.

for combustibles

5

away from open edges of the unit to avoid burns associated with unintentional spillovers. Hold the handle of the

pan to prevent movement of it when turning or stirring food. For proper lighting and performance of the burners

keep the ports clean. It is necessary to clean periodically for optimum performance.

Clean the grill with caution. Avoid steam burns; do not use a wet sponge or cloth to clean the grill while it is hot.

Some cleaners produce noxious fumes or can ignite if applied to a hot surface.

Be sure all grill controls are turned off and the grill is cool before using any type of aerosol cleaner on or around

the grill. The chemical that produces the spraying action could, in the presence of heat, ignite or cause metal

parts to corrode.

Do not use the grill for cooking excessively fatty meats or products which promote flare-ups.

Never grill without the drip pan and grease tray in place and pushed all the way to the back of the grill. Without it

hot grease could leak downward and produce a fire or explosion hazard.

Do not operate the grill under un protected combustible construction. Use only in well ventilated areas. Do not

use in buildings, garages, sheds, breezeway, covered structure or other such enclosed areas. This unit is for out-

door use only.

If a cart unit is stored indoors, ensure that it is cool, fold the side shelf down, then push, never pull, the grill and

never push or pull on the side shelves. If LP, the cylinder must be unhooked and the LP cylinder stored outside in a

well ventilated area, out of reach of children.

Never use the grill in a windy area.

Do not locate, store or operate the grill on an inclined plane. Make sure you lock the castor wheels before operat-

ing the grill.

Do not use charcoal or lighter fluid in the grill.

Keep any electrical supply cord, or the rotisserie motor cord away from the heated areas of the grill and water

(pools, fountains, puddles).

Never use a dented or rusty LP tank. Keep the ventilation openings of the cylinder enclosure free and clear from

debris.

Use only dry potholders; moist or damp potholders on hot surfaces may cause burns from steam. Do not use a

towel or bulky cloth in place of potholders. Do not let potholders touch hot portions of the grill or burner grate.

Have an ABC rated Fire Extinguisher accessible – never attempt to extinguish a grease fire with water or other liq-

uids.

To avoid burns when cooking, use long handled BBQ tools.

Do not move the appliance during its use.

This unit is for outdoor use only! Do not operate in enclosed areas. This could result in carbon monoxide build-up

which would result in injury or death.

When using the grill, be sure that all parts of the unit are firmly in place and that the grill is stable (can’t be tipped

over).

To reduce the risk of flare-ups, adjust the controls to lower the temperature

CALIFORNIA PROPOSITION 65-WARNING: The Burning of gas cooking fuel generates some by-products which are

on the list of substances which are known by the State of California to cause cancer or reproductive harm. Califor-

nia law requires businesses to warn customers of potential exposure to such substances. To minimize exposure to

these substances, always operate this unit according to the manual, ensuring you provide good ventilation when

cooking with gas.

This outdoor cooking gas appliance is not intended to be installed in or on recreational vehicles, trailers and/or

boats.

Note:

This product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of

Massachusetts.

SAFETY PRACTICES & PRECAUTIONS

6

BH130R

BGC30BQ

GRILL MODELS

7

INSTALLATION

LOCATING GRILL/BUILTIN CLEARANCES

LOCATION:

When determining a suitable location take into account concerns such as exposure to wind, proximity to traffic

paths and keeping any gas or electrical supply lines as short as possible and away from heat sources. Locate the

grill only in a well ventilated area. Do not build the grill under overhead unprotected combustible construction.

Never locate the grill in a building, garage, breezeway, shed or other such enclosed areas. During heavy use, the

grill will produce a lot of heat and smoke. Ensure there is adequate area for it to dissipate.

If locating the grill in a windy area, try to locate the grill so the prevailing wind will blow air at the front of the

grill as shown in Fig. 01. This will assist the grill in venting hot air thru the back of the grill. In addition, this will

help keep any smoke from blowing at someone who is cooking on the grill. If you have to locate the grill in a

windy area where the prevailing wind is at the rear of the grill, a windbreak must be installed. The windbreak

should be made such that it will block wind from entering the exhaust vent in the rear of the unit as shown in Fig.

01. Location of the windbreak relative to rear of the grill must adhere to the clearances specified for combustible

or non-combustible construction as defined in these instructions. Refer to following pages.

As high-performance gas appliance, your grill requires significant amounts of air to support the combustion

process. Your grill is designed to take air in through the valve panel area, and send the exhaust products out

through the exhaust gap at the rear of the hood. Using your grill in windy conditions can disrupt the proper flow

of air though your grill, leading to reduced performance, or in certain severe cases, causing heat buildup in the

valve panel area. This can lead to problems such as having the knobs melt, or burn hazards when the valve panel

surfaces become too hot to touch.

During high wind conditions, it is best if you don’t use your grill. If you live in an area that is subject to frequent

high winds, or a steady directional wind, then the installation of a suitable windbreak may be advised. If you have

a grilling cart, it is best to position the unit so the prevailing wind blows into the valve panel, thus supporting the

proper airflow. Winds hitting the back of the grill directly are the most likely to cause problems, although wind

blowing along the exhaust gap in the rear can also be problematic.

Please note that damage to your grill resulting from use in windy conditions, such as melted knobs or igniter

wires, or valve panel discoloration from heat build-up, are excluded from warranty coverage.

Important!

Gas fittings, regulator, and installer supplied shut-off valves must be easily accessible.

PREFERRED

AIR FLOW

GRILL EXHAUST

EXHAUST

FLAME

BURNER

Wind hitting the grill

while in use,

especially winds

blowing into or across

this hood gap, can

cause poor

performance and in

some cases can cause

the control panel and

knobs to get

dangerously hot.

WIND

GRILL PLACEMENT

FLAME LIFT

FIG. 01

BH1-30R model illustrated

WIND

PRIMARY

INTAKE

AIR FLOW

If wind is an

issue, a wind

screen should

be added. The

wind screen

should be

higher than

the top of the

opening in the

back of the

grill, with a

minimum

clearance of 3"

(7,6cm) (for

non-combusti-

bles) or 18"

(45,7cm) (for

combustibles)

from the back

WIND SCREEN

WIND

15” min.

(38,1cm)

EXHAUST VENT FLOW

3”

(7,6 cm) min.

for non-

combustibles

18” (45,7cm)

min.

for combustibles

8

(7,6cm)

(61,6cm)

(5,5cm)

2-3/16”

22-5/16”

(56,7cm)

(64,77cm)

(26,67cm)

(25,4cm)

26-5/8”

(67,6cm)

/ 99,06cm

FIG. 02

INSTALLATION

LOCATING GRILL/BUILTIN CLEARANCES

(BH1-30R illustrated)

Clearances to Non-Combustible Construction*

Clearances to Combustible Construction**:

Minimum of 18” /45,7cm from the sides and rear of grill must be maintained to adjacent vertical combustible con-

struction, above the counter top level. You should take in account that there is a large volume of heat, and smoke

will exhaust from the rear of the grill. This may discolor or damage unprotected areas (Fig. 03). Do not install

under unprotected combustible construction without using a fire safe ventilation system.

A 18” /45,7cm minimum clearance must be maintained under the counter top to combustible construction. The

clearance can be modified by a use of an insulated jacket.

Clearances to Non-Combustible Construction*:

A minimum of 3” / 7,6cm clearance from the back of the grill to non-combustible construction is required for the

purpose of allowing the lid to open fully. It is desirable to allow at least 6” / 15,2cm rear and side clearance to

non-combustible construction above the cooking surface for counter space. If you’ll be using the rotisserie option

(BGC30-BQR models only), the space is essential for motor and skewer clearance. The grill can be placed directly

adjacent to non-combustible construction below the cooking surface. (Fig. 02).

WARNING!

Failure to maintain required clearances creates a fire hazard that may result in property damage or serious personal

injury.

WARNING!

The BGC/BH1 Grills are designed to function in an open area. Recommended minimum clearances should be main-

tained to all surfaces (combustible and noncombustible) for optimum performance. Noncombustible material within

the minimum clearance area could result in discoloration or deterioration.

WARNING!

If a noncombustible material such as stucco is covering a combustible material such as wood, the minimum clear-

ance distance needs to be held to the wood. The presence of a noncombustible material inside the clearance zone

does not eliminate the minimum clearance zone to combustible material.

* DEFINITION OF NONCOMBUSTIBLE MATERIAL - Material which is not capable of being ignited and burned, such as

materials consisting entirely of, or a combination of, steel, iron, brick tile, concrete, slate, and plaster.

9

INSTALLATION

LOCATING GRILL/BUILTIN CLEARANCES ALL MODELS

Important!

It is required that a minimum of (3)10 sq. inches / 64,5cm

2

of ventilation opening be provided for both the left

and right sides, as well as the back of enclosure (Fig. 04), in order to safely dissipate unburned gas vapors in

the event of a gas supply leak.

WARNING!

Note specific built-in enclosure ventilation requirements. See text and Fig. 04.

GENERAL

The grill is designed for easy placement into built-in masonry enclosures. For non-combustible applications the

grill drops into the opening shown in Fig. 04 and hangs from its side flanges. A deck is not required to support it

from the bottom. When using the insulated jacket in a combustible enclosure application, see the bottom of Fig.

04. The insulation jacket assembly must be supported from the bottom by a ledge on each side and back or a

solid deck.

A carpenter’s “spirit level” should be used to assure that the unit is level both front-to-back and side-to-side. If it

is not level, burner combustion may be erratic or the unit may not function efficiently for grease flow. If the floor

is uneven or has a decided slope, re-leveling may be required after each moving of a freestanding unit.

INSULATED JACKET:

WARNING!

Installing this product into a combustible enclosure without an insulated jacket could result in fire, property damage

and personal injury.

If the grill is to be placed into a combustible enclosure, an approved insulated jacket is necessary. Insulated jack-

ets are available from your dealer. Use only the DCS insulated jacket which has specifically been designed and

tested for this purpose. Review the detail drawing shown (Fig. 04) and take into account the provisions shown for

gas line hook-up clearance in the right rear corner. It is required that ventilation holes are provided in the enclo-

sure to eliminate the potential build-up of gas in the event of a gas leak. The supporting ledges or deck must be

level and flat and strong enough to support the grill and insulated jacket. The counter should also be level.

** DEFINITION OF COMBUSTIBLE MATERIAL - Any materials of a building structure or decorative structure made of

wood, compressed paper, plant fibers, vinyl/plastic or other materials that are capable of transferring heat or be-

ing ignited and burned. Such material shall be considered combustible even though flame-proofed, fire-retardant

treated or surface-painted, or plastered.

rotisserie

motor

24-1/4"

10-1/2"

26-5/8"

(67,6cm)

grill

exhaust

Maintain18"

(45,7cm) min.

from combustible

construction

10 "

25-1/2"(64,77cm)

22-5/16" (56,7cm)

2-3/16"

(5,5cm)

Bottom of

support ange

18"

(45,7cm)

min.

18"

(45,7cm)

min.

(25,4cm)

(26,67cm)

30"(76,2cm)

(61,6cm)

FIG. 03

(BH1-30R illustrated)

Clearances to Combustible Construction**

10

INSULATED JACKET

Size Part No.

30 70859

grill

exhaust

7,6 cm/3 " (to non-combustible

construction / minimum lid

clearance)

45,7 cm (18") (to combustible

construction)

25,4 cm/10 "

56,7 cm/22-3/16 "

64,77 cm/25 1/2 "

2,5 cm/1 "

5,5 cm/

2-3/16 "

34,93 cm/

13 3/4 "

Standard layout for non-combustible enclosure:

NOTE: BGB models, if using a backguard

apron or rear wall, locate electrical service

on the right hand side for rotisserie motor

72,39 cm/28 1/2"

Bottom of

support flange

3 3/4" / 9,5cm Min. for Lid Clearance

18 3/4" /47,6cm Min. for Lid Clearance

71,12 cm/28 "

88,58 cm/34 7/8 "

60,33 cm/23 3/4 "

8,89 cm/3 1/2 "

46,50 cm/

18 1/4 "

50,8 cm/20 "

28,26 cm/11 1/8 "

90.17 cm/

35 1/2" max

opening for access

doors/drawers

(see Fig. 05 and 06 for

ordering information)

opening for access

doors/drawers

(see Fig. 05 and 06 for

ordering information)

10x10 cm

(4 x 4 ") opening

for gas

supply line

10x10 cm

(4 x 4 ") opening

for gas supply line

57,79 cm/22 3/4 "

46,99 cm/

18 1/2 "

50,8 cm/20 "

25,72 cm/

10 1/8 "

90.17 cm/

35 1/2 " max

Layout for insulated jacket only - combustible enclosure:

NOTE: If using a backguard apron or rear

wall, locate electrical service on the right

hand side for rotisserie motor connection

(BGB models only)

Ventilation min.

64,5 cm

2

/10

"2

Ventilation min.

64,5 cm

2

/10

"2

Ventilation min.

64,5 cm

2

/10

"2

Ventilation min.

64,5 cm

2

/10

"2

Ventilation min.

64,5 cm

2

/10

"2

Ventilation min.

64,5 cm

2

/10

"2

2,54 cm/1 " min.

NOTE: See Fig. 05

for ventilation notes.

71,12 cm/28 "

WARNING!

If installing the grill into a

non-combustible enclosure,

all combustible construction

must still be outside the 18

inch / 45,7cm clearance

zone. If your island is made

of stucco over the top of

wooden studs, the wood can

not be inside the 18 inch

clearance zone to

combustible, even though

the stucco is what is

touching the grill area.

INSTALLATION

BUILTIN CONSTRUCTION DETAILS

FIG.04

Note:

The gas connection must be visible to the user (through a door opening or similar).

Gas piping and connectors must be clamped within the the enclosure to avoid contact with moving parts and hot surfaces.

Where the gas piping passes through an opening in the enclosure, the piping must be protected for a distance of at least 2” (50mm) either side of the

opening.

The gas connector must comply with the Standard for Connectors for Outdoor Gas Appliances & Manufactures Homes, ANSI Z21.75/ CSA 6.27.

The connection must be no longer than 6’ (1820mm) in length and be suitable for outdoor installation.

(BH1-30R illustrated)

11

FIG.04

FIG. 05

Access Doors

Cutout dimensions

A

90º

B

Vent*

MODEL NUMBER A B

+0,1/8 +1/8,0

ADN120x48 46” 20”

ADN120x36 34” 20”

ADN120x30 28” 20”

ADN120x24 22” 20”

Cutout for Access Doors

Access Drawers

Cutout dimensions

NOTE: The cutout of each corner should be 90

º

angle in order for the access drawers

to fit properly.

* Island installation to use minimum of 3 vents, 10 square inches (25,4cm2) per vent

(typical).

** For proper support and drawer operation, insure that support boards are

installed per Installation Guide instructions

To order access drawers or doors, please call DCS Customer Care at 1.888.936.7872 for DCS Dealer in your area.

MODEL NUMBER A B C

+0,1/8 +1/8,0

ADR2 48 46” 20”

ADR236 34” 20”

ADR230 28” 20”

ADR224 22” 20”

24-1/2”

(Min,

All

Models)

NOTE: The cutout of each corner should be 90

º

angle in order

for the access drawers to fit properly.

* Island installation to use minimum of 3 vents,

10 square inches (25,4cm2) per vent (typical).

FIG. 06

INSTALLATION

BUILTIN CONSTRUCTION DETAILS

12

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

IMPORTANT!

Read all instructions before you begin. Do not jump ahead or skip any step.

CAUTION!

Some parts have sharp edges; care must be taken when handling the various components to avoid injury. Please

read safety information provided in these instructions before beginning assembly. Wear gloves when handling.

Two or more people should work together to assemble the cart and grill head.

Note:

Avoid using side shelf to move cart. Push or pull cart by grasping corners of grill head.

GETTING STARTED

n

Remove packaging.

n

Remove side shelf and side tray from inside and discard packing.

Contents Included:

Your cart is packaged in one box. The box contains your 30” grill cart

and a universal hardware kit to be used for BH1-30R grill installation

and may contain extra hardware for your convenience.

Contents Qty.

5

1

5

Machine

philip screws

10-24X1/2”

Bolt

1/4-20X1/2”

Bolt

1/4-20X2”

Keps Nut

1/4-20

Rubber

Bumper

Tools Required:

Eye Goggles

Work Gloves

10 mm Wrench or Socket

3/32” Allen Wrench

Power Screwdriver or Vari-

able Speed Drill with Phillips

-tip #2 Attachment

Contents Qty.

1

30” Grill Cart

Side Shelf

Side Shelf Tray

Instruction

13

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

STEP 2

Grill Placement onto Cart (2 persons required)

1. Remove drip tray/pan for easier

handling. Place grill head on cart.

2. Slide back.

3. Ease over rear flange.

4. Secure with screws.

Install 2 bolts (1/4-20X1/2” bolts &

1/4-20 keps nut) in the front

brackets as shown.

Install 2 bumpers on

each side.

Install all 3bolts

(1/4-20X1/2” bolts &

1/4-20 keps nut) in the

rear brackets as shown.

FIG. 08 After drip tray/pan is removed, carefully

place grill head on cart (2 person minimum).

(Model shown may vary)

FIG. 09 Once grill rests on cart, slide grill to

rear of cart as shown.

STEP 1

Attach Side Shelf on the Right Side (left side is optional side burner location)

1. Attach shelf to right side of the cart using 1/4-20 nuts and bolts provided [leave out (1) bolt front side as shown

below].

2. Do not tighten bolts (finger tight only) until completing Step 4.

3. Install bumpers to the sides of the cart as shown below.

FIG. 07

14

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

FIG. 11 Grill head should rest over rear cart

flange as shown above.

FIG. 12 Secure grill to rear of cart with (2) phil-

lips-head screws provided (10-24 x 1/2”).

Pinch Point

FIG. 10 Lift grill over rear flange of cart (be

aware of pinch points).

STEP 3

Front End Screw Installation

1. Install remaining (3) screws (10-24X1/2”) in front of head to cart.

2. Slide drip tray/pan back into place. Move side shelf bars up and set

trays into place.

STEP 4

Bolt Installation

After head is in place, install the bolt (1/4-20 x 2”) omitted from Step

1, and tighten all bolts on bracket. Tighten until sides are flush with

the trim only.

Note:

This bolt secures side bracket to grill head assembly for added side shelf

strength. Apply Loctite 242 (blue) to the first 3-4 threads prior to instal-

lation of this bolt

FIG. 13 Secure grill to the front of the cart with Phillips-

head screws (provided).

FIG. 14 Front right side

15

STEP 5

Side tray adjustment

1. Take the tray and place it onto the handle at a upright position. Make sure the tray sits snugly around the handle.

2. Then tighten the rest of the loose bolts that were not tightened in Step 1.

Side shelf adjustment

1. With extended use, the shelves may become

unleveled and need to be readjusted.

2. In between the bracket where the handle

slides in is a 5/8” long adjustment screw.

Grasping the handle as shown, raise up the

shelf and hold while with other hand using a

3/32 allen wrench turn to the desired level.

3. Slide drip tray/pan back into place.

4. Move side shelf bars up and set trays into place.

STEP 6

Gas Hookup - LP

Attach LP gas line connector hose assem-

bly (as shown in “LP Gas Hookup” section)

and then connect to LP tank as shown

below.

Shelf Level

Adjustment

INSTALLATION

CART ASSEMBLY INSTRUCTIONS

FIG. 15 FIG. 16

FIG. 17

FIG. 18 FIG. 19

FIG. 20 FIG. 21

16

Note: All gas piping and connectors must conform to the Standard for Connectors for Outdoor Gas Appliances

and Manufactured Homes, ANSI Z21.75/CSA 6.27.

GAS REQUIREMENT

Verify the type of gas supply to be used, either natural or LP, and make sure the marking on the appliance rat-

ing plate agrees with that of the supply. The rating plate is located underneath the drip tray. Never connect an

unregulated gas line to the appliance. You must use the gas regulator provided with the unit, even if the supply is

controlled.

An installer-supplied gas shut-off valve must be installed in an easily accessible location. All installer supplied

parts must conform to local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA

70 or the Canadian Electrical Code, CSA C22.1, and the National Fuel Gas Code, ANSI Z223.1 or CSA B149.1 Natural

Gas Installation Code or CSA B149.2 Propane Installation Code.

All pipe sealants must be an ap proved type and resistant to the actions of LP gases. Never use pipe sealant on

flare fittings. All gas connections should be made by a qualified technician and in accordance with local codes

and ordinances. In the absence of local codes, the installation must comply with the National Fuel Gas Code,

ANSI Z223.1. Gas conversion kits are available from Customer Care. When ordering gas conversion kits, have the

model number, and the type of gas (natural or LP) from your grill.

TOTAL GAS CONSUMPTION OF THE GRILL WITH ALL BURNERS ON HI:

BH1-30R - 64,000 Btu/hr or 67.5MJ/h BGC30-BQ 50,000Btu/h or MJ/h

The appliance and its individual shut-off valve must be disconnected from the gas supply piping system during

any pressure testing of that system at test pressures in excess of 1/2 PSIG (3.5 kPa.) The appliance must be isolat-

ed from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing

of the gas supply piping system at test pressures equal to or less than 1/2 PSIG (3.5 kPa.). The installation of this

appliance must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54. Installation in Can ada must be in accordance with Natural Gas and Propane Installation Code,

CSA B149.1, and/or Propane Storage and Handling

Code, B149.2 and local codes.

NATURAL GAS HOOK UP: THIS TYPE OF

CONNECTION SHOULD BE PERFORMED BY A

CERTIFIED OR LICENSED TECHNICIAN ONLY.

Connection: 1/2” NPT female with 3/8” flare adapter.

Operating pressure: 4.0” W.C. 1.0kPa Supply pressure:

5” (1.2kPa) to 14” water column (2.7kPa). If in excess

of 14” W.C., a step down regulator is required. Check

with your local gas utility company or local codes for

instructions on installing gas supply lines. Be sure to

check on type and size of run, and how deep to bury

the line. If the gas line is too small, the grill will not

function properly. Any joint sealant used must be an

approved type and be resistive to the actions of LP

gases.

TO HOOKUP THE FITTINGS SUPPLIED

WITH THE GRILL:

Assemble as shown (Fig. 22). Use threading compound

on male threads only. Do not use threading compound

on the male end of the 1/2” NPT to 3/8 flare adapter.

Use a second pipe wrench to hold the grill inlet pipe to

avoid shifting any internal gas lines of the grill. Ensure that the regulator arrow points in the direction of gas flow

towards the unit, away from the supply. Do not forget to place the installer-supplied gas valve in an accessible

location.

LP GAS HOOK UP TYPE 1 OR QCC1 REGULATOR:

Grills orificed for use with LP gas come equipped with a high capacity hose/regulator assem bly for connection to

a standard 20 lb / 9kg. LP cylinder (Type 1). The LP tank is not included.

Bottom of unit

Threading compound

must be resistant to LP gas

Coupling

1/2” NPT x

2.0”

NIpple

Regulator

4.0" W.C.

Adapter 1/2” NPT

to 3/8” flare fitting

Do not put threading

compound on these

threads

*Installation must conform with local

codes or with the National Fuel Gas Code

ANSI Z223.1 or the CSA B149.2 Propane

Installation Code

Installer supplied shut-off

valve must be easily

accessible*

1/2” NPT x 5.0”

Close

Nipple

FIG. 22 Natural Gas

INSTALLATION

GAS HOOKUP

Connection: LP Hose with a Type 1 quick disconnect and regulator is included. Operating pressure: 11.0” W.C /

2.7kPa.

CAUTION!

Before connecting LP tank to regulator, check that all grill burners, and rotisserie valves (BH1-30R models) are in the

OFF position and open grill lid.

To connect the LP regulator/hose assembly to the tank/valve assembly, first make sure the main valve on the

tank is completely closed. Although the flow of gas is stopped when the Type 1 system is disconnected as part of

its safety feature, you should always turn off the LP tank main valve (Fig.23) after each use and during transport

of the tank or unit. Insert the regulator inlet into the tank valve and turn the black coupler clockwise until the

coupler tightens up. Do not overtighten the coupler. Turn the main tank valve on and turn the burner control

valves on the unit to the “HI” position for about 20 seconds to allow the air in the system to purge, turn valves off

and wait 5 minutes before attempting to light the burners.

To disconnect the coupler, first make sure the main tank valve is turned off. Grasp the coupler and turn counter

clockwise. The inlet will then disengage. Remove the inlet from the tank valve opening if it has not already done

so when it disengaged. Your local LP filling station should be equipped with the proper equipment to fill your

tank.

LP TANK REQUIREMENTS:

A dented or rusty LP tank may be hazardous and should be checked by your LP supplier. The cylinder that is

used must have a collar to protect the cylinder valve. Never use a cylinder with a damaged valve. Always check

for leaks after every LP tank change. The LP gas cylinder must be constructed and marked in accordance with the

specifications for LP gas cylinders of the U.S. Department of Transportation (DOT or CAN/CSA-B339) and designed

for use with a Type 1 system only. Do not change the regulator/hose assembly from that supplied with the unit

or attempt to use a Type 1 equipped regulator/hose assembly with a standard 510 POL tank/valve assembly. The

cylinder must be provided with a shut-off valve terminating in a LP gas supply cylinder valve outlet specified, as

applicable, for connection Type 1. If the appliance is stored indoors, the cylinder must be disconnected and

removed from the appliance. Cylinders must be stored outdoors in a well-ventilated area out of the reach of

children.

Note:

When an LP unit is being directly connected to an LP house sys-

tem, you must follow the natural gas hook up guidelines. The

installer must provide the proper gas regulator to reduce the gas

pressure to 11” W.C / 2.7kPa.

Note:

The Grill comes with the LP Regulator/Hose assembly installed at

the factory. The assembly, along with the entire Grill system, is

leak tested. Do not remove the Regulator/Hose assembly from

the Grill during installation.

WARNING! :

1. Do not remove the Grill from the pallet until you are ready

to install.

2. Do not place the Grill directly on the ground or any other

flat surface without support. This will prevent damaging

the regulator/hose assembly by the weight of the grill.

3. Check the hose, regulator and connectors for damage. Look for cracks, abrasions, brittleness, holes, dents and

nicks.

4. Do not attempt to remove, repair, or replace the Regulator/Hose assembly by yourself. It must be done by a

qualified technician only.

17

FIG. 23 LP Gas

INSTALLATION

GAS HOOKUP

Bottom of unit

Elbow 45

º

1/2” female

NPT x 3/8” male f lare

(installed on the unit)

LP Regulator hose

assembly 11" W.C/

2.7kPa.

Type 1 Regulator

Main Tank Valve

20 lb. LP Tank

*Installation must conform with

local codes or with the National

Fuel Gas Code ANSI Z223.1 or the

CSA B149.2 Propane Installation

Code

18

INSTALLATION

GAS HOOKUP

LP TANK RESTRAINT FOR BUILTIN INSTALLATION

If the grill is to be installed in a Built-in application, then the grill must be installed in accordance with the

Built–in installation guidelines.

If you intend to operate your Built-in grill on LP gas utilizing a 20 lb Type 1 cylinder, then the Built-in LP tank

restraint must be installed prior to initial use of the grill. If you do not have one please contact DCS Customer Care

at (888) 936-7872 for information on obtaining one.

The following steps will illustrate how to properly locate and install the LP tank restraint within the Built-in enclo-

sure.

NOTE:

The grill comes with the LP Regulator/Hose assembly installed at the factory. The assembly, along with the entire grill

system, is leak tested.

Do not remove the Regulator/Hose assembly from the grill during installation.

FIG. 24

18” / 45,7cm max.

The maximum distance from the center

of the manifold cut out to the center of

the tank restraint is 18 “ / 45,7cm.

Center of manifold cut

out projected to floor

of the island.

Center of Tank Restraint must be

placed within this area to avoid

causing stress on the LP regulator

hose connection.

La page charge ...

DCS BH1-30R-N Le manuel du propriétaire

DCS BH1-30R-N Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents