City Theatrical Legacy 5702M SHoW Baby 6 Manuel utilisateur
- Catégorie
- Stroboscopes
- Taper
- Manuel utilisateur
SHoW DMX SHoW Baby® 6
Wireless DMX Transceiver
P/N 5702M
User’s Manual
Rev 4.0
© 2018 City Theatrical, Inc.
SHoW DMX Transceivers are covered by U.S. Patent # 7,432,803 and other patents pending.
2
Table of Contents
Radio Compliance Information ...................................................................................................... 3
5792M SHoW DMX Radio CE Declaration of Conformity ......................................................... 6
System Compliance Information ................................................................................................... 7
Safety Notices ............................................................................................................................... 7
Introduction ................................................................................................................................... 8
SHoW DMX SHoW Baby® 6 Neo Settings ................................................................................ 8
SHoW DMX SHoW Baby® 6 Antennas ..................................................................................... 9
DMX512 Setup and Operation ...................................................................................................... 9
Transmitter Setup ...................................................................................................................... 9
Receiver Setup ........................................................................................................................ 10
RDM Operation ........................................................................................................................... 10
Installing the Mounting Bracket ................................................................................................... 11
3
Radio Compliance Information
5792M SHoW DMX Neo® Radio Transceiver
FCC ID: VU65792
IC ID: 7480A5792
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
Radio Frequency Notifications
FCC Notifications
RF Radiation The Product is an intentional radiator of Radio Frequency (RF) energy. In order to limit RF
exposure to personnel in the immediate area, the Product should be located and installed such that a
separation of at least 20 centimeters is maintained between the Product’s antenna and personnel in the
vicinity of the device.
Modification Warning
Caution: changes or modifications to this equipment, not expressly approved by City Theatrical Inc. could
void the user’s authority to operate the equipment.
Industry Canada Notifications
This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Product Installation and Configuration Guide © City Theatrical Inc. 2007
5792M Approved Antenna
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
This device has been designed to operate with the antennas listed below. Antennas not included in this
list or having a gain greater than 6 dB are strictly prohibited for use with this device. The required antenna
impedance is 50 ohms.
4
5792M FCC/IC Approved Antennas:
Manufacturer Model Type Connector Gain
Nearson S151AH-2450S Omni whip SMA plug reverse polarity 5dBi
Nearson S141AH-2450 Omni whip SMA plug reverse polarity 2dBi
Nearson S131AH-2450 Omni whip SMA plug reverse polarity 2dBi
Nearson DG102N-2.4/5.25 Omni whip SMA plug reverse polarity via
provided Antenna Cable 5dBi
Centurion WCP2400-MMCX4 Omni whip MMCX jack on 4” coax pigtail 2.5dBi
Maxrad MP24008XFPT Panel SMA plug reverse polarity via
provided Antenna Cable 8dBi
Maxrad MYP24010PT Yagi SMA plug reverse polarity via
provided Antenna Cable 10dBi
Maxrad MYP24014PT Yagi SMA plug reverse polarity via
provided Antenna Cable 14dBi
5792M CE Approved Antennas:
Manufacturer Model Type Connector Gain
Nearson S151AH-2450S Omni whip SMA plug reverse polarity 5dBi
Nearson S141AH-2450 Omni whip SMA plug reverse polarity 2dBi
Nearson S131AH-2450 Omni whip SMA plug reverse polarity 2dBi
Nearson DG102N-2.4/5.25 Omni whip SMA plug reverse polarity via
provided Antenna Cable 5dBi
Centurion WCP2400-MMCX4 Omni whip MMCX jack on 4” coax pigtail 2.5dBi
CE Mark Conformity
City Theatrical Inc. declares that this product conforms to the specifications listed in this manual, following
the provisions of the European R&TTE directive 1999/5/EC:
City Theatrical Inc. vakuuttaa täten että dieses produkt tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien näiden direktiivien muiden ehtojen mukainen.
City Theatrical Inc. déclare que le produit est conforme aux conditions essentielles et aux dispositions
relatives à la directive 1999/5/EC.
•
EN 301 489-1, 301 489-17 General EMC requirements for Radio equipment.
•
EN 60950 Safety
•
EN 300 328 Technical requirements for Radio equipment.
CAUTION—This equipment is intended to be used in all EU and EFTA countries.
Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact
local Authority for procedure to follow.
Note: ESD precautions should be used when attaching or removing the antenna.
Note: Combinations of power levels and antennas resulting in a radiated power level of above 100 mW
equivalent isotropic radiated power (EIRP) are considered as not compliant with the above mentioned
directive and are not allowed for use within the European community and countries that have adopted the
European R&TTE directive 1999/5/EC. For more details on legal combinations of power levels and
antennas, contact City Theatrical Inc.
Do not use this product near water, for example, in a wet basement or near a swimming pool.
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from
lightning.
5
Product Installation and Configuration Guide © City Theatrical Inc. 2011
Q52 Regulatory information
Radio Frequency Notifications
Belgique Dans le cas d'une utilisation privée, à l'extérieur d'un bâtiment, au-dessus d'un espace public,
aucun enregistrement n'est nécessaire pour une distance de moins de 300m. Pour une distance
supérieure à 300m un enregistrement auprès de l'IBPT est requise. Pour une utilisation publique à
l'extérieur de bâtiments, une licence de l'IBPT est requise. Pour les enregistrements et licences, veuillez
contacter l'IBPT.
France 2.4 GHz Bande : les canaux 10, 11, 12, 13 (2457, 2462, 2467, et 2472 MHz respectivement) sont
complétement libres d'utilisation en France (en utilisation intérieur). Pour ce qui est des autres canaux, ils
peuvent être soumis à autorisation selon le départment. L'utilisation en extérieur est soumis à autorisation
préalable et très restreint. Vous pouvez contacter l'Autorité de Régulation des Télécommunications
(http://www.art-telecom.fr) pour de plus amples renseignements.
6
5792M SHoW DMX Radio CE Declaration of Conformity
7
System Compliance Information
The 5702M SHoW DMX SHoW Baby® 6 Transceiver is CE Certified
Standards Applied:
BS EN 60950-1:2002 incorporating Corrigendum No. 1 and Amendment No. 1
EN 55203-1: 1996
EN 55203-2: 1996
EN 301 489-1 V1.4.1
EN 301 489-3 V1.4.1
Products Conform to CE Marking Directive 93/68/EEC
All SHoW DMX models are RoHS compliant
Safety Notices
Please read this entire manual before using your new equipment. Please keep the manual in a
safe place so you can refer to it in the future as required.
The SHoW DMX System is intended for use only by qualified professionals. Connection,
installation, and hanging of this equipment must be performed in accordance with all pertinent
local, regional, and national safety codes and regulations.
SHoW DMX equipment is intended for indoor use only unless specified for outdoor use.
Keep the equipment dry! Do not operate the equipment if it gets wet!
Do not operate in excessive heat/direct sunlight.
Be sure installation provides adequate ventilation.
There are no user-serviceable parts inside! Refer to qualified service personnel!
RF Exposure: The antenna(s) used for this transmitter must be installed to provide a
separation distance of at least 20cm from all persons and must not be collocated or operating in
conjunction with any other antenna or transmitter.
8
Introduction
Thank you for using City Theatrical’s SHoW DMX SHoW Baby® 6 Wireless DMX/RDM
Transceiver.
The SHoW DMX SHoW Baby 6 represents a breakthrough in plug-and-play wireless DMX and
RDM transmission, and can be used either as a wireless DMX transmitter or receiver. All you
need now to set up a SHoW DMX wireless DMX system is two SHoW DMX SHoW Babys and
two minutes!
The SHoW DMX SHoW Baby 6 features include:
SHoW DMX Neo® 2.4GHz Frequency Hopping Spread Spectrum (FHSS) Radio
Wirelessly broadcast and receive a full Universe (512 slots) of DMX
Robust wireless DMX512 and RDM data transmission
Six Possible SHoW IDs – including the original SHoW Baby 201
Full Compatibility with previous SHoW Babys
Extremely low 7mS max latency
RDM proxy and responder functions
Instant plug-and-play configuration: For a Transmitter, connect DMX IN, for a Receiver,
don’t!
72mW ETSI broadcast power (with 2dBi Antenna)
Mounting bracket for installation with C-Clamp or similar hanging hardware
Included CL2 Power Supply
Included 2dBi Omni-directional Antenna
Neutrik® 5P XLR Connectors for DMX IN and DMX OUT (3 pin in 5702M-3)
Every effort has been made to anticipate your questions in this manual, but if you have any
questions that are not answered here, or you want to discuss a special application, please feel
free to contact us directly at City Theatrical.
SHoW DMX SHoW Baby 6 Neo Settings
The SHoW DMX SHoW Baby 6 uses the 5792 SHoW DMX Neo Radio Module. It is
permanently configured with six SHoW ID options for Adaptive Spread Spectrum Frequency
Hopping and Neo Low Latency broadcast mode. Using RDM, you can adjust SHoW ID, adjust
the broadcast power, edit the RDM Device Label, and enable or disable RDM traffic. No other
settings are adjustable. The SHoW ID can also be changed by pressing the small button on
the back of the SHoW DMX SHoW Baby® 6 labeled “SET ID”.
Color SHoW ID Description
Green 201 Neo Adaptive
Cyan 102 Neo Full Bandwidth
Magenta 117 Neo Low Limited Bandwidth
White 133 Neo Mid Limited Bandwidth
Red 149 Neo High Limited Bandwidth
Yellow 165 Neo High Limited Bandwidth
9
SHoW DMX SHoW Baby 6 Antennas
The SHoW DMX SHoW Baby 6 is shipped with a 2dBi omni directional antenna. Any of the
approved antennas listed above may be used with the SHoW DMX SHoW Baby® 6 (please
note the special installation requirements for use with the CTI # 5636 14 dBi Yagi Antenna).
ETSI power settings for all 5792M SHoW DMX Neo Radio module equipped products,
including the SHoW DMX SHoW Baby 6, are based on use with the CTI 5630 5 dBi Omni
Antenna. ETSI power and range will vary with the antenna used. Contact your dealer or City
Theatrical for more information.
DMX512 Setup and Operation
Rear View Front View
A SHoW DMX SHoW Baby 6 system will normally consist of at least two SHoW Baby 6 units.
Transmitter Setup
Although a simple SHoW Baby 6 system will have one transmitter and one or more receivers,
you can use up to six SHoW Baby 6 units as transmitters set on different SHoW IDs to create a
multi universe system. The following instructions describe how to set up a single universe
system.
1. Install the SHoW DMX SHoW Baby 6 you will use for a transmitter in a convenient
location where you can reach it with the DMX cable from your console or controller. For
best results, locate the unit as high in the air as possible to enable it to be clear of
obstructions. Consider where you will put your SHoW Baby 6 receivers and place the
SHoW Baby 6 transmitter where its antenna will be within line of sight with the receivers, if
possible.
2. Install the provided antenna and point it straight up in the air.
3. Connect the provided 12V DC Power Supply to the unit, and connect to mains power.
4. Select a SHoW ID for your transmitter by choosing an ID/Data LED color using the Set ID
button located on the rear next to the power jack.
5. Connect a DMX cable from the console/controller to the DMX IN. The SHoW Baby 6 will
automatically configure itself as a transmitter and the Tx LED will light. The DMX IN will be
automatically terminated, and the DMX OUT will be available as a DMX pass-thru. If you
also connect a cable to the DMX OUT the termination is lifted.
6. As soon as you begin sending DMX from your console, the SHoW Baby 6 will begin
broadcasting and the Data LED will light solid.
10
Receiver Setup
You will need at least one SHoW DMX SHoW Baby 6 to use as a receiver.
1. Install the SHoW Baby 6 you will use for a receiver in a convenient location where you
can reach it with a DMX cable to the device (or devices) it will be providing DMX for. As
with the SHoW Baby 6 transmitter, locate the unit higher in the air for best results, and try
to place your SHoW Baby 6 receiver where its antenna will be within line of sight with the
transmitter.
2. Install the provided antenna and point it straight up in the air.
3. Connect the provided 12V DC Power Supply to the unit, and connect to mains power.
The SHoW Baby 6 will be configured as a receiver and the Rx LED will light.
4. Select a SHoW ID by matching the ID/Data LED color to that of the transmitting SHoW
Baby 6 you wish to receive DMX data from by using the button located on the rear of the
unit next to the power jack. Transmitter and receiver SHoW ID colors must match for
them to communicate.
5. Connect a DMX cable from the SHoW Baby 6 DMX OUT to the first DMX device you
want to provide DMX to. You can then continue to add up to 32 more DMX devices to the
chain. Like any other DMX system, be sure the last connected device in the chain is
properly terminated.
6. As soon as you begin broadcasting from the SHoW Baby 6 set up as your transmitter, the
data will be received by the SHoW Baby(s) 6 set up as receiver(s) and the transmitted
DMX will be output from the receiver unit’s DMX OUT. The received signal strength will
be displayed on the four LO – RF Signal – HI LEDs. This four LED “meter” will light to
show you your signal strength; a good wireless signal is three or more LEDs, and weaker
signal is two or less.
You can set up any number of additional SHoW Baby 6 units as receivers.
RDM Operation
RDM stands for Remote Device Management. RDM is a lighting control protocol
enhancement to DMX512 specified by PLASA (formerly ESTA); the official name is ANSI/
ESTA E1.20, Entertainment Technology - Remote Device Management over USITT DMX512.
To learn more about RDM, a good place to start is the Wikipedia article on RDM (lighting) at:
http://en.wikipedia.org/wiki/RDM_(lighting)
SHoW DMX SHoW Baby 6 is fully enabled as an RDM proxy system, so you can use RDM to
manage your SHoW DMX SHoW Baby 6 system and any connected RDM responders that
are downstream of the system.
11
In order to use RDM, you will also need an RDM controller or a lighting control console with a
built-in RDM controller.
SHoW DMX SHoW Baby® 6 supports the following read-only PIDs:
PROXIED_DEVICE_COUNT
PROXIED_DEVICES_ENHANCED
SUPPORTED_PARAMETERS
PARAMETER_DESCRIPTION
PRODUCT_DETAIL_ID_LIST
DEVICE_MODEL_DESCRIPTION
MANUFACTURER_LABEL
FACTORY_DEFAULTS
SOFTWARE_VERSION_LABEL
SENSOR_DEFINITION
SENSOR_VALUE, OUTPUT_POWER
SHoW DMX SHoW Baby® 6 supports the following editable PIDS:
SHoW ID(editable, 201, 102, 117, 133, 149, 165)
DEVICE_LABEL (editable)
RDM_TRAFFIC_ENABLE (editable, 01 = enable, 00 = disable)
OUTPUT_POWER (editable, 00=1mW, 01=14mW, 02=28mW, 03=72mW)
In order to allow RDM traffic and discovery and control of connected Responders you must
enable RDM Traffic (Set RDM_TRAFFIC_ENABLE to 01).
Note that DMX transmission fidelity may be slightly reduced when RDM Traffic is enabled.
Installing the Mounting Bracket
The SHoW DMX SHoW Baby 6 is provided with a Mounting Bracket for use with ½”
theatrical mounting hardware like a C-Clamp.
Mount the Bracket on the SHoW DMX SHoW Baby 6 using the 3 provided 8-32 x 1/2" Pan
Head Philips screws.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
City Theatrical Legacy 5702M SHoW Baby 6 Manuel utilisateur
- Catégorie
- Stroboscopes
- Taper
- Manuel utilisateur