Datalogic MEMOR 11 Rugged Mobile Computer Mode d'emploi
- Catégorie
- Batteries rechargeables
- Taper
- Mode d'emploi
NOTE: Read carefully the MEMOR 11 User Manual
(available at www.datalogic.com) before performing any
type of connection to the MEMOR 11.
The user is responsible for any damage caused by
incorrect use of the equipment or by inobservance of the
indication supplied in the user manual.
GENERAL SAFETY RULES
CAUTION:
• Before using the devices and the battery packs, read
this Addendum carefully.
• Use only the components and accessories supplied
by the manufacturer for the specific MEMOR 11 being
used.
• Do not attempt to disassemble the MEMOR 11 device,
as it does not contain parts that can be repaired by the
user. Any tampering will invalidate the warranty.
• When replacing the battery pack or at the end of the
operative life of the MEMOR 11 device, disposal must
be performed in compliance with the laws in force in
your jurisdiction.
• Do not submerge the MEMOR 11 in liquid products.
• For further information or support, refer to the
Datalogic web site: www.datalogic.com.
CAUTION:
Do not apply any sticker to the MEMOR 11.
POWER SUPPLY
The device is intended to be supplied by a self-contained rechargeable
Lithium Ion battery pack (UL listed LPS/SELV power source) and/or by
UL Listed/CSA Certified Power Unit LPS/SELV power source which sup-
plies power directly to the unit via the micro USB connector of the cable.
The device could be also used with Certified Accessories (Dock/Cradle)
which supply Wireless power. The Dock/Cradle accessories are inten-
ded to be supplied by a UL Listed/CSA Certified Power Unit LPS/SELV
rating 12V, min 5A power source which supplies power via the power
connector of the cable.
Any changes or modifications to equipment, not expressly approved by
Datalogic could void the user’s authority to operate the equipment.
BATTERY INFORMATION
CAUTION: Do not incinerate, disassemble, short
terminals, or expose to high temperature. Risk of fire and
explosion. Use specified charger only. Risk of explosion
if the battery is replaced by an incorrect type. Dispose of
batteries as required by local authorities.
By default, the main battery pack is disconnected at the factory to avoid
damage due to excessive draining.
Rechargeable battery pack is less than half of full charge when deli-
ve-red. Charge the battery pack as indicated in the Quick Start Guide or
in the User Manual, before using the MEMOR 11 terminal.
The battery pack autonomy varies according to many factors, such as
the frequency of barcode scanning, RF usage, battery life, storage, envi-
ronmental conditions, etc.
To maximize battery life, turn off radios when they are not needed.
Close to the limits of the working temperature, some battery per-
for-mance degradation may occur.
The MEMOR 11 should be charged at an ambient temperature
between 0 - 35° C (32 to 122°F) to achieve the maximum char-
ging rate.
Never charge the device battery in a closed space where excessive
heat can build up. As a safety precaution, the battery may stop char-
ging to avoid overheating.
The MEMOR 11 gets warm during charging; this is normal and does
not mean a malfunction.
Even if the storage temperature range is wider, in order to achieve
the longest battery life, store the terminal and the spare batteries
between 20 to 30°C (68 to 86°F).
To maximize operating autonomy, the Memor 11 checks its battery
level at all times. If the battery is not sufficiently charged, the Memor
11 will not turn on when the ON/OFF Power button is pressed.
In this case, either substitute with a charged battery, insert the
Memor 11 into a powered cradle, or plug it into a wall charger.
CAUTION: Avoid storing batteries for long periods in a
state of full charge or very low charge or in a state of
continuous charging, especially at temperature higher
than 30°C.
We recommend charging the battery pack every two to
three months, if it is not used for long time, to keep its
charge at a moderate level to maximize battery life.
Annual replacement of rechargeable battery pack
avoids possible risks or abnormalities and ensures
maximum performance.
WARNING: Use only Datalogic approved batteries and
accessories for battery charging.
Risk of explosion if battery is replaced by an incorrect
type.
Dispose of used batteries according to the instructions.
Il y a risque d’explosion si la batterie est remplacée par
une batterie de type incorrect.
Mettre au rebut les batteris usagées confor mément
aux instructions.
CAUTION: Do not put any foreign object such as, but not
limited to, coins, paper clips, stickers inside the slot of
any of the wireless charging docks (see the examples
below).
BATTERY SAFETY GUIDELINES
WARNING: Installing, charging and/or any other action
should be done by authorized personnel and following
this manual.
The battery pack may get hot, explode, ignite, and/or
cause serious injury if exposed to abusive conditions.
If the battery pack is replaced with an improper type,
there is risk of explosion.
Do not place the battery pack in or near a fire or
other heat source; do not place the battery pack in
direct sunlight, or use or store the battery pack inside
unventilated areas in hot weather; do not place the
battery pack in microwave ovens, in clothes dryers, in
high pressure containers, on induction cook surfaces or
similar devices. Doing so may cause the battery pack to
generate heat, explode or ignite. Using the battery pack
in this manner may also result in a loss of performance
and a shortened life expectancy.
MEMOR™ 11
SAFETY & REGULATORY
ADDENDUM
Rugged Mobile Computer
with 1D/2D Imager
• All rights reserved • Without limiting
the rights under copyright, no part of this
documentation may be reproduced, stored
in or introduced into a retrieval system, or
transmitted in any form or by any means,
or for any purpose, without the express
written permission of Datalogic S.p.A.
and/or its affiliates • Datalogic and the
Datalogic logo are registered trademarks
of Datalogic S.p.A. in many countries,
including the U.S. and the E.U.
This document is an addendum to the
Quick Start Guide (QSG) for this product.
See the QSG for additional product
information.
www.datalogic.com
©2023 Datalogic S.p.A. and/or its affiliates
852002160 (Rev. A) February 2023
Datalogic S.r.l.
Via San Vitalino 13
40012 Calderara di Reno (BO)
Italy
Tel. +39 051 3147011
Fax +39 051 3147205
©2023 Datalogic S.p.A. and/or its affiliates
All rights reserved. Without limiting the rights under copyright, no part of this documentation may be repro-
duced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any
purpose, without the express written permission of Datalogic S.p.A. and/or its affiliates.
Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and tran-
smit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or
alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure
that all notices appear on any reproductions of the documentation.
Electronic versions of this document may be downloaded from the Datalogic website (www.datalogic.com).
If you visit our website and would like to make comments or suggestions about this or other Datalogic publi-
cations, please let us know via the "Contact" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accu-
rate, however, Datalogic shall not be liable for technical or editorial errors or omissions contained herein, nor
for incidental or consequential damages resulting from the use of this material. Datalogic reserves the right
to change any specification at any time without prior notice.
Trademarks
Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including
the U.S.A. and the E.U.
Memor is a trademark of Datalogic S.p.A. and/or its affiliates. All other brand and product names may be
trademarks of their respective owners.
Patents
See www.patents.datalogic.com for patent list.
This product is covered by one or more of the following patents:
Design patents: EM004675072, EM004803013, EM005513751 0001/0002, GB9004675072 0001/0002,
GB9004803013 0001/0002, GB9005513751 0001/0002, USD933062, ZL201830392430.1, ZL201930042130.5
Utility patents: EP1804089B1, EP1825417B1, EP1828957B1, EP2315156B1, EP2517148B1, EP2521068B1,
EP2616988B1, EP2649555B1, EP2795534B1, EP3234750B1, JP5192390B2, US10671277, US10762405,
US10817685, US7234641, US7721966, US8113430, US8245926, US8561906, US8888003, US8915443,
US9122939, US9430689, US9798948, ZL200680050007.8, ZL200980163411.X, ZL201080071124.9,
ZL201180044793.1, ZL201580074380.6.
CLEANING THE DEVICE
Periodically clean the MEMOR 11 using a so cloth slightly dampened with only water or Iso-
propyl Alcohol (70%). Do not use any other cleaning agents (e.g. different alcohol, abrasive or
corrosive products, solvents) or abrasive pads to clean the device.
Do not spray or pour liquids directly onto the device.
The device is IP65 waterproof.
WARNING: To power the cradle, use only a Datalogic approved power supply. The
use of an alternative power supply will void the product warranty, may cause product
damage and may cause heat, an explosion, or fire.
The area in which the units are charged should be clear of debris and combustible
materials or chemicals.
Do not use the battery pack of this terminal to power devices other than this device.
Avoid storing batteries for long periods in a state of continuous charging, full charge
or very low charge, especially at temperature higher than 30°C.
Periodically check the battery status and immediately discontinue use of the battery
pack if, while using, charging or storing the battery pack, the battery pack emits an
unusual smell, feels hot, changes colour or shape, swelling or appears abnormal in
any other way.
Do not short-circuit the battery pack contacts connecting the positive terminal and
negative terminal. This might happen, for example, when you carry a spare battery
pack in your pocket or purse; accidental short-circuiting can occur when a metallic
object such as a coin, clip, or pen causes direct connection of the contacts of the
battery pack (these look like metal strips on the battery pack). Short-circuiting the
terminals may damage the battery pack or the connecting object.
Do not apply voltages to the battery pack contacts.
Do not pierce the battery pack with nails, strike it with a hammer, step on it or
otherwise subject it to strong impacts, pressures, or shocks.
Do not disassemble or modify (i.e. bend, crush or deform) the battery pack. The
battery pack contains safety and protection devices, which, if damaged, may cause
the battery pack to generate heat, explode or ignite.
In case of leakage of liquid from the battery, avoid contact with liquid the skin or
eyes. If the contact occurs, immediately wash the affected area with water and
consult a doctor.
Do not solder directly onto the battery pack.
Do not expose the battery pack to liquids.
Avoid any knocks or excessive vibrations. If the device or the battery is dropped,
especially on a hard surface, you should take it to the nearest Authorised Repair
Centre for inspection before continuing to use it.
If your device stops working for any reason, do not use its battery on other electronic
devices without a prior check and approval by an Authorised Repair Centre.
Do not remove or damage the battery pack’s label.
Do not use the battery pack if it is damaged in any part.
Battery pack usage by children should be supervised.
Collect and recycle waste batteries separately from the device in compliance with
European Directive 2013/56, 2011/65, 2012/79 and subsequent modifications, with
US and China regulatory laws and regulations about the environment.
WIRELESS AND RADIO FREQUENCIES WARNINGS
WARNING: Most modern electronic equipment is shielded from RF signals. However,
certain electronic equipment may not be shielded against the RF signals generated
by MEMOR 11.
Datalogic recommends persons with pacemakers or other medical devices to follow
the same recommendations provided by Health Industry Manufacturers Associations
for mobile computers.
Persons with pacemakers:
• Should ALWAYS keep this device more than twenty five (25) cm from their
pacemaker and/or any other medical device;
• Should not carry this device in a breast pocket;
• Should keep the device at the opposite side of the pacemaker and/or any other
medical device;
• Should turn this device OFF or move it immediately AWAY if there is any reason
to suspect that interference is taking place.
• Should ALWAYS read pacemaker or any other medical device guides or should
consult the manufacturer of the medical device to determine if it is adequately
shielded from external RF energy.
In case of doubt concerning the use of wireless devices with an implanted medical
device, contact your doctor.
Turn this device OFF in health care facilities when any regulations posted in these
areas instruct you to do so. Hospitals or health care facilities may use equipment
that could be sensitive to external RF energy.
WARNING: RF signals may affect improperly installed or inadequately shielded
electronic systems in motor vehicles. Check with the manufacturer or its
representative regarding your vehicle. You should also consult the manufacturer of
any equipment that has been added to your vehicle.
An air bag inflates with great force. DO NOT place objects, including either installed
or portable wireless equipment, in the area over the air bag or in the air bag
deployment area. If a vehicle’s wireless equipment is improperly installed and the
air bag inflates, serious injury could result.
Turn off the device when in any area with a potentially explosive atmosphere.
Observe restrictions and follow closely any laws, regulations, warnings and best
practices on the use of radio equipment near fuel storage areas or fuel distribution
areas, chemical plants or where any operation involves use of explosive materials.
Do not store or carry flammable liquids, explosive gases or materials with the device
or its parts or accessories.
Areas with a potentially explosive atmosphere are oen, but not always, clearly
marked or shown.
Sparks in such areas could cause an explosion or fire, resulting in injury or even
death.
LASER SAFETY
The following information applies to Laser Aiming System, used on MEMOR 11. The laser light is
visible to the human eye and is emitted from the window indicated in the figure below.
LASER RADIATION - DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAX OUTPUT RADIATION 1 mW
COMPLIANT WITH EN 60825-1 (2014)
NOTE: The artwork below may be only a dra. Please refer to the label attached to
the product for information about certification marks.
ENGLISH
The following information is provided to comply with the rules imposed by international authori-
ties and refers to the correct use of your device.
STANDARD LASER SAFETY REGULATIONS
This product conforms to the applicable requirements of both CDRH 21 CFR 1040 and EN 60825-1
at the date of manufacture.
For installation, use and maintenance, it is not necessary to open the device.
WARNING: Do not attempt to open or otherwise service any components in the optics
cavity. Opening or servicing any part of the optics cavity by unauthorized personnel
may violate laser safety regulations. The optics system is a factory only repair item.
Use of controls or adjustments or performance of procedures other than those
specified herein may result in exposure to hazardous visible laser light.
Use of optical systems with the scanner will increase eye hazard. Optical instruments
include binoculars, microscopes, eye glasses and magnifying glasses.
The product utilizes a low-power laser diode. Although staring directly at the laser beam momen-
tarily causes no known biological damage, avoid staring at the beam as one would with any very
strong light source, such as the sun. Avoid that the laser beam hits the eye of an observer, even
through reflective surfaces such as mirrors, etc.
ITALIANO
Le seguenti informazioni vengono fornite dietro direttive delle autorità internazionali e si riferi-
scono all’uso corretto del terminale.
NORMATIVE STANDARD PER LA SICUREZZA LASER
Questo prodotto risulta conforme alle normative vigenti sulla sicurezza laser alla data di produ-
zione: CDRH 21 CFR 1040 e EN 60825-1.
Non si rende mai necessario aprire l’apparecchio per motivi di installazione, utilizzo o manuten-
zione.
ATTENZIONE: Non tentare di accedere allo scomparto contenete i componenti ottici
o di farne la manutenzione.
L’apertura dello scomparto, o la manutenzione di qualsiasi parte ottica da parte di
personale non autorizzato, potrebbe violare le norme della sicurezza. Il sistema
ottico può essere riparato solamente alla fabbrica.
L’utilizzo di procedure o regolazioni differenti da quelle descritte nella
documentazione può provocare un’esposizione pericolosa a luce laser visibile.
L’uso di strumenti ottici assieme allo scanner può aumentare il pericolo di danno
agli occhi. Tali strumenti ottici includono cannocchiali, microscopi, occhiali e lenti
di ingrandimento.
Il prodotto utilizza un diodo laser a bassa potenza. Sebbene non siano noti danni riportati dall’oc-
chio umano in seguito ad una esposizione di breve durata, evitare di fissare il raggio laser così
come si eviterebbe qualsiasi altra sorgente di luminosità intensa, ad esempio il sole. Evitare inol-
tre di dirigere il raggio laser negli occhi di un osservatore, anche attraverso superfici riflettenti
come gli specchi.
DEUTSCH
Die folgenden Informationen stimmen mit den Sicherheitshinweisen überein, die von internatio-
nalen Behörden auferlegt wurden, und sie beziehen sich auf den korrekten Gebrauch vom Termi-
nal.
NORM FÜR DIE LASERSICHERHEIT
Dies Produkt entspricht am Tag der Herstellung den gültigen EN 60825-1 und CDRH 21 CFR 1040
Normen für die Lasersicherheit.
Es ist nicht notwendig, das Gerät wegen Betrieb oder Installations- und Wartungs-Arbeiten zu
öffnen.
ACHTUNG: Unter keinen Umständen darf versucht werden, die Komponenten im
Optikhohlraum zu öffnen oder auf irgendwelche andere Weise zu warten. Das
Öffnen bzw. Warten der Komponenten im Optikhohlraum durch unbefugtes Personal
verstößt gegen die Laser-Sicherheitsbestimmungen. Das Optiksystem darf nur
werkseitig repariert werden.
Jegliche Änderungen am Gerät sowie Vorgehensweisen, die nicht in dieser
Betriebsanleitung beschrieben werden, können ein gefährliches Laserlicht
verursachen.
Die Verwendung von Optiksystemen mit diesem Scanner erhöht die Gefahr einer
Augenbeschädigung. Zu optischen Instrumenten gehören unter anderem Ferngläser,
Mikroskope, Brillen und Vergrößerungsgläser.
Der Produkt benutzt eine Laserdiode. Obwohl zur Zeit keine Augenschäden von kurzen Ein-
strahlungen bekannt sind, sollten Sie es vermeiden für längere Zeit in den Laserstrahl zu schauen,
genauso wenig wie in starke Lichtquellen (z.B. die Sonne). Vermeiden Sie es, den Laserstrahl
weder gegen die Augen eines Beobachters, noch gegen reflektierende Oberflächen zu richten.
Laser Warning Label
Laser Aperture/Ouverture Laser
ITALIANO DEUTSCH FRANÇAIS ESPAÑOL
LA LUCE LASER È VISI-
BILE ALL’OCCHIO UMANO
E VIENE EMESSA DALLA
FINESTRA INDICATA
NELLA FIGURA.
DIE LASER-STRAHLUNG
IST FÜR DAS MEN-
SCHLICHE AUGE
SICHTBAR UND WIRD AM
STRAHLAUS TRITTSFEN-
STER AUSGESENDET
(SIEHE BILD).
LE RAYON LASER EST
VISIBLE À L’OEIL NU
ET IL EST ÉMIS PAR LA
FENÊTRE DÉSIGNÉE SUR
L’ILLUSTRATION DANS
LA FIGURE.
A LUZ LÁSER ES VISIBLE
AL OJO HUMANO Y ES
EMITIDA POR LA VEN-
TANA INDICADA EN LA
FIGURA.
LUCE LASER NON FIS-
SARE IL FASCIO
APPARECCHIO LASER
DI CLASSE 2 MASSIMA
POTENZA D’USCITA: 1
mW
LUNGHEZZA D’ONDA
EMESSA: 630~680 nm
CONFORME A EN
60825-1 (2014).
LASERSTRAHLUNG
NICHT IN DEN STRAHL
BLICKEN PRODUKT
DER LASERKLASSE 2
MAXIMALE AUSGANG-
SLEISTUNG: 1 mW
WELLENLÄGE: 630~680
nm
ENTSPR. EN 60825-1
(2014).
RAYON LASER EVITER DE
REGARDER LE RAYON
APPAREIL LASER DE
CLASSE 2 PUISSANCE DE
SORTIE: 1 mW
LONGUEUR D’ONDE
EMISE: 630~680 nm
CONFORME A EN
60825-1 (2014).
RAYO LÁSER NO MIRAR
FIJO EL RAYO APARATO
LÁSER DE CLASE 2
MÁXIMA POTENCIA DE
SALIDA: 1 mW
LONGITUD DE ONDA
EMITIDA:
630~680 nm
CONFORME A EN
60825-1 (2014).
FRANÇAIS
Les informations suivantes sont fournies selon les règles fixées par les autorités internationales
et se réfèrent à une correcte utilisation du terminal.
NORMES DE SECURITE LASER
Ce produit est conforme aux normes de sécurité laser en vigueur à sa date de fabrication: CDRH
21 CFR 1040 et EN 60825-1.
Il n’est pas nécessaire d’ouvrir l’appareil pour l’installation, l’utilisation ou l’entretien.
ATTENTION: Ne pas essayer d’ouvrir ou de réparer les composants de la cavité
optique. L’ouverture de la cavité optique ou la réparation de ses composants par une
personne non qualifiée peut entraîner le nonrespect des règles de sécurité relatives
au laser. Le système optique ne peut être réparé qu’en usine.
L’utilisation de procédures ou réglages différents de ceux donnés ici peut entraîner
une dangereuse exposition à lumière laser visible.
L’utilisation d’instruments optiques avec le scanneur augmente le danger pour les
yeux. Les instruments optiques comprennent les jumelles, les microscopes, les
lunettes et les verres grossissants.
Le produit utilise une diode laser. Aucun dommage aux yeux humains n’a été constaté à la suite
d’une exposition au rayon laser. Eviter de regarder fixement le rayon, comme toute autre source
lumineuse intense telle que le soleil. Eviter aussi de diriger le rayon vers les yeux d’un observa-
teur, même à travers des surfaces réfléchissantes (miroirs, par exemple).
ESPAÑOL
Las informaciones siguientes son presentadas en conformidad con las disposiciones de las auto-
ridades internacionales y se refieren al uso correcto del terminal.
NORMATIVAS ESTÁNDAR PARA LA SEGURIDAD LÁSER
Este aparato resulta conforme a las normativas vigentes de seguridad láser a la fecha de produc-
ción: CDRH 21 CFR 1040 y EN 60825-1.
No es necesario abrir el aparato para la instalación, la utilización o la manutención.
ATENCIÓN: No intente abrir o de ninguna manera dar servicio a ninguno de los
componentes del receptáculo óptico. Abrir o dar servicio a las piezas del receptáculo
óptico por parte del personal no autorizado podría ser una violación a los reglamentos
de seguridad. El sistema óptico se puede reparar en la fábrica solamente.
La utilización de procedimientos o regulaciones diferentes de aquellas describidas
en la documentación puede causar una exposición peligrosa a la luz láser visible.
El uso de sistemas ópticos con el escáner aumentará el riesgo de daños oculares.
Los instrumentos ópticos incluyen binoculares, microscopios, lentes y lupas.
El aparato utiliza un diodo láser a baja potencia. No son notori os daños a los ojos humanos a
consecuencia de una exposición de
corta duración. Eviten de mirar fijo el rayo láser así como evitarían cualquiera otra fuente de lumi-
nosidad intensa, por ejempl o el sol.
Además, eviten de dirigir el rayo láser hacia los ojos de un observador, también a través de super-
ficies reflectantes como los espejos.
FCC COMPLIANCE
NOTICE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause unde-
sired operation.
FCC ID: U4GDL36LT
NOTE: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCCRules.
These limits are designed to provide reasonable protection against harmful interference in a resi-
dential installation. This equipment generates uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a parti-
cular installation. If this equipment does cause harmful interference to radio or television recep-
tion, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV technician for help.
Body-worn Operation
This device was tested for typical body-worn operations. To comply With RF exposure require-
ments, a minimum separation distance of 1.0cm must be maintained between the user’s body
and the handset, including the antenna. Third-party belt-clips, holsters, and similar including the
antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not
contain any metallic com-ponents. Body-worn accessories that do not meet these requirements
may not comply with RF exposure requirements and should be avoided.
Specific Absorption Rate (SAR) information:
This wireless mobile computer meets the government’s requirements for exposure to radio
waves. The guidelines are based on standards that were developed by independent scientific orga-
nizations through periodic and thorough evaluation of scientific studies. The standards include a
substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement:
The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: U4GDL36LT
has also been tested against this SAR limit. The highest SAR value reported under this standard
during product certification for use at the ear is 1.4W/kg and when properly worn on the body is
1.29W/kg and as hotspot is 1.29W/kg. This device was tested for typical body-worn operations
with the back of the handset kept 1cm from the body. To maintain compliance with FCC RF expo-
sure requirements, use accessories that
maintain a 1cm separation distance between the user’s body and the back of the handset. The
use of belt clips, holst-ers and similar accessories should not contain metallic components in its
assembly. The use of accessories that do not satisfy these requirements may not comply with
FCC RF exposure requirements, and should be avoided. The device for operation in the band 5150-
5250 MHz is only for indoor use to reduce the potential for harmful interference to cochannel
mobile satellite systems.
ISED COMPLIANCE
NOTICE:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause unde-
sired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouil-
lage est susceptible d’en compromettre le fonctionnement.
CAUTION
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the poten-
tial for harmful interference to cochannel mobile satellite systems;
(ii) high-power radars are allocated as primary users (i.e. priority users) of the bands 5250-
5350MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to
LE-LAN devices.
The highest SAR value reported under this standard during product certification for use at the ear
is 1.4W/kg and when properly worn on the body is 1.29 W/kg and as hotspot 1.29 W/kg.
i. les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de
satellites mobiles utilisant les mêmes canaux;
ii. Les utilisateurs devraient aussi être avisés, d’une part, que les utilisateurs de radars de haute
puissance sont désignés utilisateurs principaux (c.-à-d., qu’ils ont la priorité) des bandes de 5 250
à 5 350 MHz et de 5 650 à 5 850 MHz et, d’autre part, que ces radars pourraient causer du brouil-
lage et/ou des dommages aux dispositifs de RL-EL
Au cours de la période de certification du produit, la valeur SAR la plus élevée rapportée con-
formément à cette norme est de 1.4W/kg pour l’oreille, 1.29 W/kg lorsqu’elle est correctement
portée sur le corps et 1.29W/kg lorsqu’elle est utilisée comme point chaud.
ISED radiation exposure statement
This device is compliant with SAR for general population/uncontrolled exposure limits in RSS-
102 and has been tested in accordance with the measurement methods and procedures specified
in IEEE 1528 and IEC 62209. This equipment should be installed and operated with a minimum
distance of 0.39 in(10mm) between the radiator and you body. This device and its antennas must
not be co-located or operated in conjunction with and other antenna or transmitter.
Cet appareil est conforme aux limites d’exposition DAS incontrôlée pour la population générale de
la norme CNR-102 Innovation. Scinces et Développement économique Canada et a été testé en
conformité avec les méthodes de mesure de procédures spécifiées dans IEEE 1528 et IEC 62209.
Cet appareil doit être installé et utilisé avec une distance minimale de 10mm entre I’émetteur et
votre corps. Cet appareil et sa ou ses antennes ne doivent pas être co-localisés ou fonctionner en
conjonction avec tout autre antenne ou transmetteur.
CANADIAN STATEMENT
Ne pas regarder le faisceu.
Attention classe 2 lumière laser en cas d’ouverture eviter l’esposition - lumière est émise de la
ouverture.
Ce produit est conform au sous-chapitre J de CFR 21.
Pour le modèle avec TYPE qui contient deux lettres “FD”.
Rayonnement laser – ne pas regarder dans le faisceu – ne par regarder avec strumentation opti-
que - appareil à laser de classe 2 – emission maximale de 1mw – longueur d’onde emise 630 -
680nm – selon IEC/EN 60825-1:2014.
-
1
-
2
-
3
Datalogic MEMOR 11 Rugged Mobile Computer Mode d'emploi
- Catégorie
- Batteries rechargeables
- Taper
- Mode d'emploi