GE Gas Dryer Guide d'installation

Marque: GE

Modèle: Gas Dryer

Taper: Guide d'installation

WARNING RISK OF FIRE

• To reduce the risk of severe injury or death, follow all installation instructions.

&ORWKHVGU\HULQVWDOODWLRQPXVWEHSHUIRUPHGE\DTXDOL¿HGLQVWDOOHU

• Install the clothes dryer according to these instructions and in accordance with local

codes. In the absence of local codes, installation must comply with National Fuel Gas

Code, ANSIZ223.1/NFPA 54 or the Canadian Natural Gas and Propane Installation

Code, CSA B149.1.

• California Safe Drinking Water and Toxic Enforcement Act.

This act requires the governor of California to publish a list of substances known to

the state to cause cancer, birth defects or other reproductive harm and requires

businesses to warn customers of potential exposure to such substances. Gas

appliances can cause minor exposure to four of these substances, namely benzene,

carbon monoxide, formaldehyde and soot, caused primarily by the incomplete

combustion of natural gas or LP fuels. Properly adjusted dryers will minimize

incomplete combustion. Exposure to these substances can be minimized further by

properly venting the dryer to the outdoors.

• This dryer must be exhausted to the outdoors.

• Use only 4” rigid metal ducting for exhausting the clothes dryer to the outdoors.

• DO NOTLQVWDOODFORWKHVGU\HUZLWKÀH[LEOHSODVWLFGXFWLQJPDWHULDOV,IÀH[LEOHPHWDO

(semi-rigid or foil-type) duct is installed, it must be UL listed and installed in accordance

with the instructions found in “Connecting The Dryer To House Vent” on page 6 of this

manual. Flexible venting materials are known to collapse, be easily crushed, and trap

OLQW7KHVHFRQGLWLRQVZLOOREVWUXFWGU\HUDLUÀRZDQGLQFUHDVHWKHULVNRI¿UH

• Do not install or store this appliance in any location where it could be exposed to

water and or weather.

• Save these instructions. (Installers: Be sure to leave these instructions with the

customer).

In the state of Massachusetts:

• ,QVWDOODWLRQ PXVW EH SHUIRUPHG E\ D TXDOL¿HG RU OLFHQVHG FRQWUDFWRU

SOXPEHURUJDV¿WWHUTXDOL¿HGRUOLFHQVHGE\WKHVWDWH

• :KHQXVLQJEDOOW\SHJDVVKXWRȹYDOYHVWKH\VKDOOEH7KDQGOHW\SH

• $ÀH[LEOHJDVFRQQHFWRUZKHQXVHGPXVWQRWH[FHHGIHHW

Installation

Instructions

Gas Dryer

BEFORE YOU BEGIN

Read these instructions completely and

FDUHIXOO\

• ,03257$17 Save these instructions

for local inspector’s use.

• ,03257$17 Observe all governing

codes and ordinances.

• 1RWHWR,QVWDOOHU Be sure to leave these

instructions with the customer.

• 1RWH WR &XVWRPHU  Keep these

instructions with your Owner’s Manual for

future reference.

• Before the old dryer is removed from

service or discarded, remove the dryer

door.

• Inspect the dryer exhaust outlet and

straighten the outlet walls if they are bent.

• Service information and the wiring

diagram are located in the control console.

• Do not allow children on or in the appliance.

Close supervision of children is necessary

when the appliance is used near children.

• Install the dryer where the temperature is

above 50°F for satisfactory operation of

the dryer control system.

• Product failure due to improper installation

is not covered under the Warranty.

LEVEL

8" PIPE WRENCH

10" ADJUSTABLE WRENCHES

(x2)

SLIP JOINT PLIERS

FLAT BLADE SCREWDRIVER

M ATERIALS YOU WILL NEED

EXHAUST HOOD

FLEXIBLE GAS LINE CONNECTOR

SOAP SOLUTION

FOR LEAK DETECTION

PIPE

COMPOUND

DUCT TAPE

GLOVES

SAFETY GLASSES

4" DIAM METAL ELBOW

4" DUCT CLAMPS

4" SPRING CLAMPS

(x2)

4" DIA. FLEXIBLE METAL (SEMI-RIGID)

UL LISTED TRANSITION DUCT

(IF NEEDED)

KIT WX08X10077 (INCLUDES 2 ELBOWS)

4" DIA. METAL DUCT

(RECOMMENDED)

4" DIA. FLEXIBLE METAL (FOIL TYPE)

UL LISTED TRANSITION DUCT

(IF NEEDED.)

234D2217P001 31-16735 10-13 GE

4XHVWLRQV"&DOO*(&$5(6RUYLVLWRXU:HEVLWHDW*($SSOLDQFHVFRP

,Q&DQDGDFDOORUYLVLWZZZ*($SSOLDQFHVFD

TOOLS YOU WILL

NEED

Installation Instructions

0LQLPXP&OHDUDQFH2WKHU7KDQ$OFRYHRU&ORVHW,QVWDOODWLRQ

Minimum clearance to combustible surfaces and for air opening are: 0 in. clearance both sides and 1 in. rear.

Consideration must be given to provide adequate clearance for installation and service.



GAS REQUIREMENTS

WARNING

• Installation must conform to local codes and

RUGLQDQFHVRULQWKHLUDEVHQFHWKH1$7,21$/)8(/

*$6&2'($16,=

 7KLV JDV GU\HU LV HTXLSSHG ZLWK D 9DOYH  %XUQHU

$VVHPEO\ IRU XVH RQO\ ZLWK QDWXUDO JDV 8VLQJ

FRQYHUVLRQ NLW :(; \RXU ORFDO VHUYLFH

RUJDQL]DWLRQ FDQ FRQYHUW WKLV GU\HU IRU XVH ZLWK

SURSDQH/3JDV$//&219(56,2160867%(0$'(

BY PROPERLY TRAINED AND QUALIFIED PERSONNEL

AND IN ACCORDANCE WITH LOCAL CODES AND

25',1$1&(5(48,5(0(176

7KHGU\HUPXVWEHGLVFRQQHFWHGIURPWKHJDVVXSSO\

SLSLQJ V\VWHP GXULQJ DQ\ SUHVVXUH WHVWLQJ RI WKDW

V\VWHPDWDWHVWSUHVVXUHLQH[FHVVRI36,.3D

7KHGU\HUPXVWEHLVRODWHGIURPWKHJDVVXSSO\SLSLQJ

V\VWHP E\ FORVLQJ WKH HTXLSPHQW VKXWRȹ YDOYH

GXULQJDQ\SUHVVXUHWHVWLQJRIWKHJDVVXSSO\SLSLQJ

RIWHVWSUHVVXUHHTXDOWRRUOHVVWKDQ36,.3D

GAS SUPPLY

• A 1/8-in.National Pipe Taper thread plugged tapping,

accessible for test gauge connection, must be installed

immediately upstream of the gas supply connection to

the dryer. Contact your local gas utility should you have

questions on the installation of the plugged tapping.

• Supply line is to be 1/2-in. rigid pipe and equipped with

DQDFFHVVLEOHVKXWRȺZLWKLQ IWRIDQG LQ WKHVDPH

room with the dryer.

 8VH SLSH WKUHDG VHDOHU FRPSRXQG RU 7HÀRQ WDSH

appropriate for natural or LP gas.

 <RXPXVWXVHZLWKWKLVGU\HUDÀH[LEOHPHWDOFRQQHFWRU

listed connector ANSI Z21.24 / CSA 6.10. The length of

the connect shall not exceed 3 ft.

 &RQQHFWÀH[LEOHPHWDOFRQQHFWRUWRGU\HUDQGJDVVXSSO\

 2SHQVKXWRȺYDOYH

INTERNAL DUCT

OPENING

CHECK THAT EXHAUST

HOOD DAMPER OPENS

AND CLOSES FREELY.

WALL

TILT THE DRYER SIDEWAYS

AND REMOVE THE FOAM

SHIPPING PADS BY

PULLING AT THE SIDES

AND BREAKING THEM

AWAY FROM THE DRYER

LEGS. BE SURE TO

REMOVE ALL OF THE

FOAM PIECES AROUND

THE LEGS.

PREPARING FOR INSTALLATION OF

NEW DRYER

7,3,QVWDOO\RXUGU\HUEHIRUHLQVWDOOLQJ\RXUZDVKHU

7KLVZLOODOORZEHWWHUDFFHVVZKHQLQVWDOOLQJGU\HU

H[KDXVW

DISCONNECTING GAS

5(029,1*/,17)520:$//(;+$867

OPENING

• 5HPRYHDQGGLVFDUGH[LVWLQJSODVWLFRUPHWDOIRLO

WUDQVLWLRQGXFWDQGUHSODFHZLWK8/OLVWHGWUDQVLWLRQ

GXFW

DISCONNECT AND DISCARD OLD

FLEXIBLE GAS CONNECTOR AND

OLD TRANSITION DUCTING

MATERIAL. REPLACE WITH NEW

CSA(AGA) APPROVED FLEXIBLE

GAS LINE CONNECTOR AND UL

APPROVED TRANSITION DUCT.

TURN GAS

SHUT-OFF VALVE

TO THE OFF

POSITION.

:$51,1*1(9(55(86(2/'

)/(;,%/(&211(&7256

7KHXVHRIROGÀH[LEOHFRQQHFWRUVFDQFDXVHOHDNVDQG

SHUVRQDOLQMXU\ $OZD\VXVH QHZÀH[LEOH FRQQHFWRUV

when installing gas appliances.

DRYER GAS SUPPLY CONNECTION

2-5/8"

3/8" NPT MALE THREAD GAS SUPPLY

NOTE: Add to vertical dimension

the distance between cabinet

bottom to floor.

• Gas clothes dryers input ratings are based on sea level

operation and need not be adjusted for operation at or

below 2000 ft. elevation.

For operation at elevations above 2000 ft., input ratings

should be reduced at a rate of 4 percent for each 1000

ft. above sea level.

• Installation must conform to local codes and ordinances or,

in their absence, the NATIONAL FUEL GAS CODE, ANSI Z223.

$'-867,1*)25(/(9$7,21

Installation Instructions



LEAK TEST



RECONNECTING GAS

Note:7KHFRQQHFWRUDQG¿WWLQJVDUHGHVLJQHGIRUXVH

only on the original installation and are not to be reused

IRUDQRWKHUDSSOLDQFHRUDWDQRWKHUORFDWLRQ.HHSÀDUH

end of adaptor free of grease, oil and thread sealant.

CAUTION: Use adapters as shown. Connector

nuts must not be connected directly to pipe threads.

WARNING: 1(9(586($123(1

)/$0(727(67)25*$6/($.6

FLARE

NPT

PIPE SIZE

Listed connector ANSI Z21.24

CSA 6.10

1/8" NPT PIPE

PLUG FOR

CHECKING GAS

INLET PRESSURE

AT LEAST 1/2"

3/8" NPT

TIGHTEN THE FLEXIBLE

GAS LINE USING TWO

ADJUSTABLE WRENCHES.

TIGHTEN ALL CONNECTIONS

USING TWO ADJUSTABLE WRENCHES.

DO NOT OVERTORQUE GAS CONNECTIONS!

ck all connections for leaks with soapy solution or equivalent.

ly soap solution. Leak test solution must not contain ammonia

ch could cause damage to the brass fittings. If leaks are found,

e valve, retighten the joint, and repeat the soap test.

Installation Instructions



ELECTRICAL CONNECTION

INFORMATION

ELECTRICAL REQUIREMENTS

This appliance must be supplied with 120V, 60Hz, and

connected to a properly grounded branch circuit,

protected by a 15- or 20- amp circuit breaker or time-

delay fuse. If electrical supply provided does not meet the

DERYH VSHFL¿FDWLRQV LW LV UHFRPPHQGHG WKDW D OLFHQVHG

electrician install an approved outlet.

:$51,1*TO REDUCE THE

5,6.2)),5((/(&75,&$/6+2&.

AND PERSONAL INJURY:

• '212786($1(;7(16,21&25'25$1$'$37(5

3/8*:,7+7+,6$33/,$1&(

Dryer must be electrically grounded in accordance

with local codes and ordinances, or in the absence

of local codes, in accordance with the NATIONAL

ELECTRICAL CODE, ANSI/NFPA NO. 70.

  :$51,1*  THIS DRYER IS

(48,33(' $ 7+5((3521* *5281',1*

PLUG FOR YOUR PROTECTION AGAINST

6+2&.+$=$5'$1'6+28/'%(3/8**('

DIRECTLY INTO A PROPERLY GROUNDED

7+5((3521* 5(&(37$&/( '2 127 &87

25 5(029( 7+( *5281',1* 3521*

)5207+,63/8*

ENSURE PROPER GROUND

EXISTS BEFORE USE.

IF LOCAL CODES PERMIT,

AN EXTERNAL GROUND WIRE

(NOT PROVIDED), WHICH MEETS

LOCAL CODES, MAY BE ADDED

BY ATTACHING TO THE GREEN

GROUND SCREW ON THE REAR

OF THE DRYER, AND TO A GROUNDED

METAL COLD WATER PIPE OR OTHER

ESTABLISHED GROUND.



(;+$867,1)250$7,21

:$51,1* IN CANADA AND IN THE

81,7('67$7(67+(5(48,5('(;+$867'8&7

',$0(7(5,6,1PP'212786('8&7

/21*(57+$163(&,),(',17+((;+$867

/(1*7+7$%/(

8VLQJH[KDXVWORQJHUWKDQVSHFL¿HGOHQJWKZLOO

• Increase the drying times and the energy cost.

• Reduce the dryer life.

$FFXPXODWHOLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG

7KHFRUUHFWH[KDXVWLQVWDOODWLRQLVYOUR

RESPONSIBILITY3UREOHPVGXHWRLQFRUUHFWLQVWDOODWLRQ

DUHQRWFRYHUHGE\WKHZDUUDQW\

Remove and discard existing plastic or metal foil transition

duct and replace with UL listed transition duct.

The 0$;,080$//2:$%/( duct length and number of

bends of the exhaust system depends upon the type of

duct, number of turns, the type of exhaust hood (wall cap),

and all conditions noted below. The maximum duct length

for rigid metal duct is shown in the table below.

EXHAUST LENGTH

4" DIA.

2-1/2"

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended

No. of 90º

Elbows

Rigid

Metal

Rigid

Metal

90 Feet

60 Feet

45 Feet

35 Feet

60 Feet

45 Feet

35 Feet

25 Feet

Use only

for short

run installations

(;+$8676<67(0&+(&./,67

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry of birds or

other wildlife.

• Termination should present minimal resistance to the exhaust air

ÀRZDQGVKRXOGUHTXLUHOLWWOHRUQRPDLQWHQDQFHWRSUHYHQWFORJJLQJ

• 1HYHU install a screen in or over the exhaust duct. This could cause

lint build up.

• Wall caps must be installed at least 12 in. above ground level or any

other obstruction with the opening pointed down.

SEPARATION OF TURNS

For best performance, separate all turns by at least 4 ft. of straight

duct, including distance between last turn and exhaust hood.

TURNS OTHER THAN 90º

• One turn of 45º or less may be ignored.

• Two 45º turns should be treated as one 90º turn.

• Each turn over 45º should be treated as one 90º turn.

SEALING OF JOINTS

• All joints should be tight to avoid leaks. The male end of each section

of duct must point away from the dryer.

• Do not assemble the ductwork with fasteners that extend into the

duct. They will serve as a collection point for lint.

• Duct joints can be made air and moisture-tight by wrapping the

overlapped joints with duct tape.

•

Horizontal runs should slope down toward the outdoors 1/4

inch per foot.

INSULATION

Duct work that runs through an unheated area or is near air

conditioning should be insulated to reduce condensation and lint

build-up.

• For every extra 90° elbow, reduce the allowable vent system

length by 10 ft.

• Two 45° elbows will be treated like one 90° elbow.

• For the side exhaust installations, add one 90° elbow to the

chart.

• The total vent system length includes all the straight portions

and elbows of the system (transition duct included).

Installation Instructions

GAS

INLET

PIPE

EXTERNAL

DUCT

OPENING

DUCT TAPE OR

DUCT CLAMP

DUCT TAPE OR

DUCT CLAMP

(CUT TO PROPER

LENGTH)

4" METAL DUCT

CSA (AGA) APPROVED

NEW FLEXIBLE GAS

LINE CONNECTOR

NOTE: WE STRONGLY RECOMMEND SOLID METAL EXHAUST DUCTING.

HOWEVER, IF FLEXIBLE DUCTING IS USED IT MUST BE UL-LISTED METAL

NOT PLASTIC.

FOR STRAIGHT LINE INSTALLATION, CONNECT THE DRYER EXHAUST TO

THE EXTERNAL EXHAUST HOOD USING DUCT TAPE OR CLAMP.

STANDARD REAR EXHAUST

(Vented at floor level)



(;+$867&211(&7,21

THIS DRYER COMES READY FOR REAR

(;+$867,1*,) 63$&( ,6/,0,7('86(

THE INSTRUCTIONS IN SECTION 9 TO

(;+$867',5(&7/<)5207+(6,'(625

%277202)7+(&$%,1(7

RECOMMENDED

CONFIGURATION

TO MINIMIZE

EXHAUST

BLOCKAGE.

ELBOW HIGHLY

RECOMMENDED

ELBOW HIGHLY

RECOMMENDED

NOTE: ELBOWS WILL PREVENT DUCT

KINKING AND COLLAPSING.

STANDARD REAR EXHAUST

(Vented above floor level)

:$51,1*TO REDUCE THE

RISK OF FIRE OR PERSONAL INJURY:

• This clothes dryer must be exhausted to the

outdoors.

• We recommend that you install your dryer before

installing your washer. This will permit direct access

for easier exhaust connection.

• Use only 4” rigid metal ducting for the home exhaust

duct.

 8VH RQO\ µ ULJLG PHWDO RU 8/OLVWHG ÀH[LEOH PHWDO

(semi-rigid or foil-type) duct to connect the dryer

to the home exhaust duct. It must be installed

in accordance with the instructions found in

“Connecting The Dryer To House Vent” on page 6 of

this manual.

• Do not terminate exhaust in a chimney, a wall,

a ceiling, gas vent, crawl space, attic, under an

HQFORVHG ÀRRU RU LQ DQ\ RWKHU FRQFHDOHG VSDFH

of a building. The accumulated lint could create a

potential ¿UHKD]DUG

• Never terminate the exhaust into a common duct

with a kitchen exhaust system. A combination of

JUHDVHDQGOLQWFUHDWHVDSRWHQWLDO¿UHKD]DUG

 'RQRWXVHGXFWORQJHUWKDQVSHFL¿HGLQWKHH[KDXVW

length table. Longer ducts can accumulate lint,

FUHDWLQJDSRWHQWLDO¿UHKD]DUG

• Never install a screen in or over the exhaust duct.

This will cause lint to accumulate, creating a

SRWHQWLDO¿UHKD]DUG

• Do not assemble ductwork with any fasteners

that extend into the duct. These fasteners can

DFFXPXODWHOLQWFUHDWLQJDSRWHQWLDO¿UHKD]DUG

• Do not obstruct incoming or exhausted air.

• Provide an access for inspection and cleaning of

the exhaust system, especially at turns and joints.

Exhaust system shall be inspected and cleaned at

least once year.

/(9(/,1*'5<(5

LEVEL

SIDE-TO-SIDE.

4 LEVELING LEGS

2 ANTI-TIP LEGS

LEVEL

FRONT-TO-BACK.

STAND THE DRYER UPRIGHT NEAR THE

FINAL LOCATION AND ADJUST THE 4 LEVELING

LEGS TO MATCH THE HEIGHT OF YOUR WASHER.

ADJUST THE 2 ANTI-TIP LEGS TO CONTACT

THE FLOOR.

Installation Instructions

&211(&7,1*7+('5<(572+286(9(17

RIGID METAL TRANSITION DUCT

• For best drying performance, a rigid metal transition duct is

recommended.

•

Rigid metal transitions ducts reduce the risk of crushing and kinking.

8//,67(')/(;,%/(0(7$/6(0,5,*,'75$16,7,21'8&7

 ,IULJLGPHWDOGXFWFDQQRWEHXVHGWKHQ8/OLVWHGÀH[LEOH

metal (semi-rigid) ducting can be used (Kit WX08X10077).

 1HYHULQVWDOOÀH[LEOHPHWDOGXFWLQZDOOVFHLOLQJVÀRRUVRU

other enclosed spaces.

 7RWDOOHQJWKRIÀH[LEOHPHWDOGXFWVKRXOGQRWH[FHHGIHHWP

• For many applications, installing elbows at both the dryer

and the wall is highly recommended (see illustrations below).

Elbows allow the dryer to sit close to the wall without kinking

and or crushing the transition duct, maximizing drying

performance.

• Avoid resting the duct on sharp objects.

8//,67(')/(;,%/(0(7$/)2,/7<3(75$16,7,21'8&7

• In special installations, it may be necessary to connect the

GU\HUWRWKHKRXVHYHQWXVLQJDÀH[LEOHPHWDOIRLOW\SHGXFW

$8/OLVWHGÀH[LEOHPHWDOIRLOW\SHGXFWPD\EHXVHG21/<

LQLQVWDOODWLRQVZKHUHULJLGPHWDORUÀH[LEOHPHWDOVHPLULJLG

ducting cannot be used AND where a 4” diameter can be

maintained throughout the entire length of the transition duct.

,Q&DQDGDDQGWKH8QLWHG6WDWHVRQO\WKHÀH[LEOHPHWDOIRLO

type) ducts that comply with the “Outline for Clothes Dryer

Transition Duct Subject 2158A” shall be used.

 1HYHULQVWDOOÀH[LEOHPHWDOGXFWLQZDOOVFHLOLQJVÀRRUVRU

other enclosed spaces.

 7RWDOOHQJWKRIÀH[LEOHPHWDOGXFWVKRXOGQRWH[FHHGIHHWP

• Avoid resting the duct on sharp objects.

• For best drying performance:

Slide one end of the duct over the clothes dryer outlet

pipe.

Secure the duct with a clamp.

With the dryer in its permanent position, extend the duct

to its full length. Allow 2” of duct to overlap the exhaust

SLSH&XWRȺDQGUHPRYHH[FHVVGXFW.HHSWKHGXFWDV

VWUDLJKWDVSRVVLEOHIRUPD[LPXPDLUÀRZ

Secure the duct to the exhaust pipe with the other clamp.

ELBOWS HIGHLY

RECOMMENDED

ELBOW HIGHLY

RECOMMENDED

DO NOT

SIT DRYER

ON FLEXIBLE

EXHAUST

DO NOT USE

EXCESSIVE

EXHAUST

LENGTH

DO NOT

CRUSH

FLEXIBLE

EXHAUST

AGAINST

WALL.

DON’T

$/&29(25&/26(7,167$//$7,21

• If your dryer is approved for installation in an alcove or closet,

it will be stated on a label on the dryer back.

• The dryer MUST be vented to the outdoors. See the (;+$867

INFORMATION section.

• Minimum clearance between dryer cabinet and adjacent

walls or other surfaces is:

0 in. either side

3 in. front and rear

 0LQLPXPYHUWLFDOVSDFHIURPÀRRUWRRYHUKHDGFDELQHWV

ceiling, etc. is 52 in.

• Closet doors must be louvered or otherwise ventilated and

must contain a minimum of 60 sq. in. of open area equally

distributed. If the closet contains both a washer and a dryer,

doors must contain a minimum of 120 sq.in. of open area

equally distributed.

• The closet should be vented to the outdoors to prevent gas

pocketing in case of a gas leak in the supply line.

• No other fuel-burning appliance shall be installed in the same

closet with the dryer.

MOBILE OR MANUFACTURED HOME INSTALLATION

• Installation must conform to the MANUFACTURED HOME

&216758&7,216$)(7<67$1'$5'7,7/(3$57

or, when such standard is not applicable, with AMERICAN

1$7,21$/67$1'$5')2502%,/(+20(12%.

• The dryer MUST be vented to the outdoors with the

termination securely fastened to the mobile home structure.

(See (;+$867,1)250$7,21 section 6.)

• The vent MUST NOT be terminated beneath a mobile or

manufactured home.

• The vent duct material MUST BE METAL.

• .,7'0867 be used to attach the dryer securely to

the structure.

• The vent MUST NOT be connected to any other duct, vent, or

chimney.

• Do not use sheet metal screws or other refastening devices

which extend into the interior of the exhaust vent.

• Provide an opening with a free area of at least 25 sq. in.or

introduction of outside air into the dryer room.

• Stacking of a gas dryer is not permitted in a mobile home or

manufactured home.

BATHROOM OR BEDROOM INSTALLATION

• The dryer MUST be vented to the outdoors. See (;+$867

INFORMATION section 6.

• The installation must conform with local codes or, in the

absence of local codes, with the 1$7,21$/)8(/*$6&2'(

$16,=

Installation Instructions



'5<(5(;+$867725,*+7/()725

BOTTOM CABINET

:$51,1*

BEFORE PERFORMING

7+,6(;+$867

,167$//$7,21%(685(

TO DISCONNECT THE DRYER FROM ITS

(/(&75,&$/ 6833/< 3527(&7 <285

HANDS AND ARMS FROM SHARP

EDGES WHEN WORKING INSIDE THE

&$%,1(7%(685(72:($5*/29(6

Note: Only 4” round rigid metal ducting allowed inside

dryer.

TAB LOCATION

Detach and remove the bottom, right or left side knockout

as desired. Remove the screw inside the dryer exhaust duct

and save. Pull the duct out of the dr

er.

REMOVE

SCREW

AND SAVE.

REMOVE

DESIRED

KNOCKOUT

(ONE ONLY).

ADDING NEW DUCT

ADDING ELBOW AND DUCT FOR

(;+$86772/()76,'(2)&$%,1(7

• Preassemble 4” elbow with 4” duct. Wrap duct tape

around joint.

,QVHUWGXFWDVVHPEO\HOERZ¿UVWWKURXJKWKHVLGH

opening and connect the elbow to the dryer internal

duct.

CAUTION:%HVXUHQRWWRSXOORUGDPDJH

WKHHOHFWULFDOZLUHVLQVLGHWKHGU\HUZKHQLQVHUWLQJWKH

GXFW

• Apply duct tape as shown on the joint between the

dryer internal duct and the elbow.

Cut the duct as shown and keep portion A.

FIXING HOLE

Through the rear opening, locate the tab in the middle of

the appliance base. Lift the tab to about 45º using a flat

blade screwdriver.

BEND TAB

UP 45

Reconnect the cut portion (A) of the duct to the blower

housing. Make sure that the shortened duct is aligned with

the tab in the base. Use the screw saved previously to secure

the duct in place through the tab on the appliance base.

LEFT SIDE

EXHAUST

PORTION "A"

FIXING

HOLE

EXHAUST CAN

BE ADDED TO

LEFT OR RIGHT SIDE

DUCT

TAPE

DUCT

TAPE

CAUTION:

Internal duct joints must be

VHFXUHG ZLWK WDSH RWKHUZLVH

they may separate and cause

DVDIHW\KD]DUG

GARAGE INSTALLATION (IF ALLOWED

%</2&$/&2'(6

• Dryers installed in garages must be elevated 18 inches

FPDERYHWKHÀRRU



Installation Instructions

$'',1*(/%2:)25(;+$867

THROUGH BOTTOM OF CABINET

• Insert the elbow through the rear opening and connect

it to the dryer internal duct.

• Apply duct tape on the joint between the dryer internal

duct and elbow, as shown on page 7.

$'',1*&29(53/$7(725($52)

CABINET

Connect standard metal elbows and ducts to complete

the exhaust system. Cover back opening with a plate (Kit

WE1M454) available from your local service provider. Place

GU\HULQ¿QDOORFDWLRQ

:$51,1*1(9(5/($9(7+(

%$&.23(1,1*:,7+2877+(3/$7(

PL ATE

(KIT WE1M454)

CAUTION:

Internal duct joints must be secured with tape,

otherwise they may separate and cause a

safety hazard.

CHANGING DIRECTION OF DOOR OPENING

1. 2SHQWKHGRRUDQGUHPRYHWKH¿OOHUSOXJVRSSRVLWHWKH

hinges. With the door completely open, remove the

bottom screws from each hinge on the dryer face. Insert

these screws about half way into the TOP holes, for each

KLQJHRQWKHRSSRVLWHVLGHZKHUH\RXUHPRYHGWKH¿OOHU

SOXJV$SSO\¿UPSUHVVXUHWRJHWWKHVFUHZVVWDUWHG

2. Loosen the top screws from each hinge on the dryer

face half way. With one hand holding the top of the door

and the other hand holding the bottom, remove the

door from the dryer by lifting it UP and OFF.

3. Remove the blind plate from

the hinge side of the dryer

by removing its two screws.

Remove the strike plate

from the opposite side of the

dryer by removing its two

screws. Reinstall the plates,

on the opposite sides, using

two screws in each plate.

4. Rotate the door 180º. Insert the door on the opposite

side of the opening by moving the door ON and DOWN

until the top hinge and the bottom hinge are resting on

the top screws inserted in step 1.

5. Remove the remaining screws from the side of the

opening from which the door was removed. With these

screws secure each hinge at the bottom. Tighten the

two top screws on each hinge. Reinsert the plastic plugs

on the side from which the door was removed.

LOOSEN EACH TOP HINGE

SCREW HALF WAY AND LIFT

THE DOOR UP AND OFF

ROTATE DOOR 180º AND HANG

IT ON TOP HINGE SCREWS

INSTALL AND TIGHTEN BOTTOM

SCREWS AND TIGHTEN TOP

SCREWS

INSERT PLUGS

INTO HOLES ON

OPPOSITE SIDE

FRONT PANEL

SWITCH

STRIKE

PLATE

BLIND

PLATE

REMOVE BOTTOM SCREW FROM EACH HINGE

AND INSTALL HALF WAY INTO EACH TOP OF

OPPOSITE HINGE HOLES

REMOVE 4 PLUGS AND KEEP

FOR INSERTION INTO

THE OPPOSITE SIDE

Installation Instructions

WATER SUPPLY REQUIREMENTS

Hot and cold water faucets MUST be installed within 42 in.

(107 cm) of your washer’s water inlet. The faucets MUST

be 3/4 in. (1.9 cm) garden hose-type so inlet hoses can

be connected. Water pressure MUST be between 10 and

120 pounds per square inch. Your water department can

advise you of your water pressure.

NOTE: A water softener is recommended to reduce buildup

of scale inside the steam generator if the home water

supply is very hard.

CONNECTING INLET HOSES

(on some models)

To produce steam, the dryer must connect to the cold

water supply. Since the washer must also connect to the

cold water, a “Y” connector is inserted to allow both inlet

hoses to make that connection at the same time.

NOTE: Use the new inlet hoses provided; never

use old hoses.

 7XUQWKHFROGZDWHUIDXFHWRȺ5HPRYHWKHZDVKHULQOHW

KRVHIURPWKHZDVKHU¿OOYDOYHFRQQHFWRUFROG

 (QVXUHWKHUXEEHUÀDWZDVKHULVLQSODFHDQGVFUHZWKH

IHPDOHFRXSOLQJRIWKHVKRUW KRVH RQWR WKH ZDVKHU¿OO

YDOYHFRQQHFWRU7LJKWHQE\KDQGXQWLO¿UPO\VHDWHG

 Attach the female end of the ‘’Y’’ connector to the male

FRXSOLQJRIWKHVKRUWKRVH(QVXUHWKHUXEEHUÀDWZDVKHU

LVLQSODFH7LJKWHQE\KDQGXQWLO¿UPO\VHDWHG

 ,QVHUW WKH ¿OWHUVFUHHQLQ WKH FRXSOLQJRI WKH ZDVKHU·V

LQOHW KRVH ,I D UXEEHU ÀDW ZDVKHU LV DOUHDG\ LQ SODFH

UHPRYHLWEHIRUHLQVWDOOLQJWKH¿OWHUVFUHHQ$WWDFKWKLV

coupling to one male end of the ‘’Y’’ connector. Tighten

E\KDQGXQWLO¿UPO\VHDWHG

 (QVXUHWKHUXEEHUÀDWZDVKHULVLQSODFHDQGDWWDFKWKH

dryer’s long inlet hose to the other male end of the ‘’Y’’

FRQQHFWRU7LJKWHQE\KDQGXQWLO¿UPO\VHDWHG

 (QVXUH WKH UXEEHU ÀDW ZDVKHU LV LQ SODFH DQG DWWDFK

WKH RWKHU HQG RI WKH GU\HU·V ORQJ LQOHW KRVH WR WKH ¿OO

valve connector at the bottom of the dryer back panel.

7LJKWHQE\KDQGXQWLO¿UPO\VHDWHG

 Using pliers, tighten all the couplings with an additional

two–thirds turn.

NOTE: Do not overtighten. Damage to the couplings may

result.



6(59,&,1*

:$51,1* LABEL ALL WIRES

PRIOR TO DISCONNECTION WHEN

6(59,&,1*&21752/6:,5,1*(55256

CAN CAUSE IMPROPER AND DANGEROUS

23(5$7,21$)7(56(59,&,1*

,167$//$7,21

For servicing phone numbers for replacement parts, and

other information, refer to Owner’s Manual or visit our

Web site.

&211(&7,1*,1/(7+26(6FRQW

 Turn the water faucet on.

 Check for leaks around the ‘’Y’’ connector, faucet and

hose couplings.

IMPORTANT PRODUCT NOTIFICATIONS.

Please go to www.GEAppliances.com or mail in your

Product Registration Card.

For questions on installation, call: 800.626.2000 (US) or

800-561-3344 (Canada).

Notes

GE Gas Dryer Guide d'installation

Marque: GE

Modèle: Gas Dryer

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: GE Gas Dryer Installation guide

GE Gas Dryer Guide d'installation

GE Gas Dryer Guide d'installation

dans d''autres langues

Documents connexes

Autres documents