Zephyr ZSPE36BS Mode d'emploi

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

AUG18.0201 © Zephyr Ventilation LLC.

Siena Pro

ZSP-E36BS

ZSP-E42BS

ZSP-E48BS

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

+RRG6SHFL¿FDWLRQV

................................................... 8

Mounting the Range Hood

...................................... 9

FEATURES & CONTROLS

ICON Touch Controls

................................................ 10

MAINTENANCE

Cleaning, Filter Care, Part List

.............................. 11

ACT CONVERSION

..................................................................... 12

FAN CURVE DIAGRAMS

......................................................... 13-14

WIRING DIAGRAM

...................................................................... 15

TROUBLESHOOTING

................................................................ 16

WARRANTY

.................................................................................... 17

PRODUCT REGISTRATION

.................................................... 18

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG

F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516

,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG

 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG

 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV

,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ

E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV

attics, crawl spaces or garages.

OPERATION

$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH

ground path is adequate.

Do not ground to a gas pipe.

&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an

outlet that is properly installed and grounded.

4

www.zephyronline.com

(6) 4 x 38

(2) 4 x 8

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

- Cable connector (if required by local codes)

- Duct cover extension accessory

HARDWARE PACKAGE CONTENTS

MODELS: ZSP-E36BS, ZSP-E42BS, ZSP-E48BS

PARTS SUPPLIED

1 - Hood with internal blower

2 - Baffle filters (3 for ZSP-E48BS)

1 - Duct cover assembly (top and bottom)

1 - Duct cover wall bracket

1 - 9W Brite Strip™ LED (2 for ZSP-E48BS)

1 - 10” round collar with backdraft damper

1 - Hardware package

(4) 4 x 8

List of Materials

5

Duct pieces

Tot a l

Equivalent number

length x used =

3- 1/4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

Tot a l

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 100 equivalent feet.

6” round to

3- 1/4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Installation – Ducting Calculation Sheet

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum of 10” round duct is recommended to

PDLQWDLQPD[LPXPDLUÀRZHI¿FLHQF\

Always use rigid type metal ducts only. Flexible

GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR

Use calculation worksheet on page 5 to compute

total duct work.

ALWAYS, when possible, reduce the number of

transitions and turns. If a long duct run is required,

increase duct size from 10” to 12”.

If turns or transitions are required: Install as far

away from opening and as far apart, between 2,

as possible.

Minimum mount height between range top to hood

bottom should be no less than 24”.

Maximum mount height should be no higher than

34”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV

mounted too high will be hard to reach and will

ORRVHLWVSHUIRUPDQFHDQGHI¿FLHQF\

If available, also refer to range manufacturer’s

height clearance requirements and recommended

hood mounting height above range. Always check

your local codes for any differences.

Duct cover extension kit available for ceiling

heights up to 12 feet. Turn to page 11 for part

number and ordering information.

DAMAGE-SHIPMENT / INSTALLATION:

 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH

installation.

 ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH

unit to the store in which it was bought for

repair or replacement.

 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU

or replacement is the responsibility of the

customer.

 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU

WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW

be made by arrangement between customer

and installer.

24” min.

34” max.

min. A

max. B

min. C

max. D

Standard Extension

Hood Heights Duct Cover Duct Cover

minimum (A) 27-1/2” 45“

maximum (B) 42” 78”

Ceiling Heights

minimum (C) 87-1/2” (7’ 3-1/2”) 105“ (8‘ 9”)

maximum (D) 112” (9’ 4“ ) 148” (12’ 4”)

36”

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside, unless using the recirculating option.

Use single wall rigid Metal ductwork only.

)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZFHUWL¿HG6LOYHU7DSHRU'XFW7DSH

Some Ducting Options

Installation – Ducting Options

side wall cap

w/ gravity damper

Soffit or crawl space

Roof Pitch w/

Flashing & Cap

side wall cap

w/ gravity damper

8

www.zephyronline.com

Installation – +RRG6SHFL¿FDWLRQV

TOP

FRONT

SIDE

16

11/16”

11

5/16”

1

3”

9/16”

35

7/8

”, 41

7/8

”, 47

7/8

”

STANDARD

min. ducted - 27 1/2”

min. recirc. - N/A

max. - 42”

Z1C-00SP

min. ducted - 45”

min. recirc. - N/A

max. - 78”

12

3/16”

21

15/16”

6

3/4”

6

9/16”

1”

9

15/16”

AC In

C/L

9

1. Measure from range top to hood bottom and mark line A.

´PLQLPXPIURPUDQJHWRS

2. Plum and mark center line.

 0DUNPRXQWLQJKHLJKWOLQH%´IURPOLQH$

4. Mark mounting spread from C/L on line B 14-15/16”

 )DVWHQ[VFUHZVLQWRVWXGVRQOLQH%'RQRWIDVWHQ

screws all the way. Note: wood blocking may need to

be added behind the drywall if no studs are present.

Wall anchors may also be used but check local codes

for compliance. Failure to use suitable wall anchors

and screws to hold the weight of the hood could result

in personal injury or damage to cooking surface or

counter.

6. Install 10” round duct collar with backdraft damper to top of

KRRGE\[VFUHZV

 +DQJKRRGRQWRVFUHZVDQGKDQGWLJKWHQ),*$8VH

the last 4 x 38 screws to further secure the hood to the wall

IURPLQVLGHWKHKRRG),*$

8. Center and attach duct cover bracket to wall below ceiling

RUVRI¿WXVLQJ[VFUHZV

9. Position electrical outlet within the space covered by the

telescopic duct covers and where it will not interfere with

WKHURXQGGXFW),*%

10. Install duct work and duct tape.

11. Power up hood and check for leaks around duct tape.

12. Place telescopic duct covers onto hood and extend inner

WRSGXFWFRYHUXSZDUGVDQGVHFXUHWRGXFWFRYHUEUDFNHW

XVLQJ[VFUHZV

A

C

B

C/L

12-1/8"

1-3/8"

14-15/16"

13"

C/L

24" min

2

1

Duct Cover Bracket

CAUTION: At least two installers are

required due to the weight and size of the

hood.

!

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be

properly grounded. Turn off electrical power at service entrance before wiring.

!

Installation – Mounting the Hood

FIG. A

24”

MAX.

HOOD

CENTERLINE

4¼”

MAX.

12”

FIG. B

10

www.zephyronline.com

Lights On/Dim/Off

Display (speed level, delay off, filter clean/change)

Adjust 5 Speed Levels

Power / Delay Off

1 POWER / DELAY OFF BUTTON

Power Button Function

- Button will turn power on and off for entire hood (fan and lights).

- Hood will remember the last speed and light level it was turned off at.

(Example: Press Button to turn off hood when on fan speed 4 and high lights. Press Button

again and the hood will turn back on at speed 4 and high lights level.)

Delay Off Button Function

- With the fan on press and hold the Button for two seconds. The fan will change to speed 1 and the

5 minute delay off timer will start.

+ LEDs will illuminate and slowly blink in accordance with the time

remaining until the fan and lights automatically turn off.

- Pressing Button while Delay Off Function is enabled will turn the hood off and cancel the Delay Off

Function.

ACT Verification

- Airflow Control Technology (ACT) allows the installer to set the maximum fan CFM to align with local

codes and regulations.

- To verify the maximum fan CFM:

- With hood off, hold the Button for two seconds. If all five fan speed indicators illuminate =

default maximum CFM. If three fan speed indicators illuminate = 590 maximum CFM. If 2

fan speed indicators illuminate = 390 maximum CFM.

2 SPEED SELECTION BUTTON

Fan Speed Decrease Button

- Press this button to decrease fan speed. 5, 4, 3, 2, 1.

- If fan is On Speed 1 and this button is pressed, fan will power Off.

Fan Speed Increase Button

- Press this button to increase fan speed. Fan On, 1, 2, 3, 4, 5.

- If hood is Off and this button is pressed, fan will turn On Speed 1.

Act Enabled Speed Selections

- When ACT is enabled, the number of fan speeds will be reduced as follows:

- 590 CFM = Maximum 3 speeds

- 390 CFM = Maximum 2 speeds

3 LIGHTS BUTTON

- Lights are two levels, High and Low.

- From off, press one time for High. Press again for Low. Press again to power lights off.

4 DISPLAY INDICATORS

Baffle Filter Clean Reminder (always enabled)

- After 30 hours of fan usage, the button indicator will begin to slowly blink indicating it is time to

clean the baffle filters.

- To reset: With hood off: hold the button for three seconds. All LED indicators will blink two times

confirming the 30 hour timer has been reset.

Features & Controls - ICON Touch Controls

11

SURFACE MAINTENANCE:

Clean the hood surface periodically with hot soapy water and clean cotton cloth. Do not use corrosive or

abrasive detergent, or steel wool/scouring pads which will scratch and damage surface.

For heavier soil use liquid degreaser.

After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and

buff out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.

Do not use any product containing chlorine bleach. Do not use “orange” cleaners.

%DIÀH)LOWHUV

7KHEDIÀH¿OWHUVLQVWDOOHGE\WKHIDFWRU\DUHLQWHQGHGWR¿OWHURXWUHVLGXHDQGJUHDVHIURPFRRNLQJ7KH\

need not be replaced on a regular basis but are required to be kept clean.

Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if

heavily soiled.

'U\¿OWHUVDQGUHLQVWDOOEHIRUHXVLQJKRRG

5HPRYLQJ%DIÀH)LOWHUV

1. Push in on spring loaded handle

3XOOGRZQRQ¿OWHUKDQGHWRUHPRYH¿OWHU

6KRXOG¿OWHUVZHDURXWGXHWRDJHDQGSURORQJHGXVH

replace with following part number:

Maintenance – Cleaning, Filter Care & Part List

LIST OF PARTS & ACCESSORIES

DESCRIPTION PART#

Replacement Parts

%DIÀH)LOWHUHDFK 

Optional Accessories

Duct Cover Extension Kit Z1C-00SP

Universal Make-Up Air Damper MUA010A

To order parts, visit us online at http://store.zephyronline.com or call us at 1.888.880.8368

12

www.zephyronline.com

ACT Conversion

ALUÀRZ&RQWURO7HFKQRORJ\$&7

Some local codes limit the maximum amount of CFM a range hood can move. ACT allows you to control the

maximum blower CFM of select Zephyr Ventilation range hoods without the need for expensive make up air kits.

$&7HQDEOHVWKHLQVWDOOHUWRHDVLO\VHWWKHPD[LPXPEORZHUVSHHGWRRQHRIWZRPRVWFRPPRQO\VSHFL¿HG&)0

OHYHOVRU&)07KHXVDJHRI$&7PD\QRWEHQHFHVVDU\IRU\RXULQVWDOODWLRQ3OHDVHFKHFN\RXUORFDO

codes for CFM restrictions.

By default the maximum blower CFM is set to 1200.

To enable ACT

1. Before hood installation, gain access to PC board by following the steps shown in FIG. C.

2. Change plastic jumper positioning as shown in FIG. D to set the desired maximum blower CFM.

3. Re-install PC board & continue with hood installation.

4. Remove the appropriate foil CFM sticker included with the hood literature and place inside the hood body below

the wiring diagram or in another clearly visible location.

NOTE: After re-positioning the jumper and powering on the hood, the CFM cannot be changed again.

To verify if your installer enabled ACT

With hood off, press and hold the power button for three seconds. If 5 LEDs illuminate = defualt max. CFM, if 3

LEDs illuminate = max. 590 CFM, and if 2 LEDs illuminate = max. 390 CFM.

When ACT is enabled, the number of blower speeds will be reduced. 590 CFM = max. 3 speeds and 390 CFM =

max. 2 speeds.

There should also be a foil label located inside the hood body near the wiring diagram that indicates the blower

CFM.

PC Board

1

3

5

7

2

4

6

8

Jumper 5-6 or 7-8

DEFAULT POSITION

Default Max. Blower CFM

Jumper 3-4

Max. Blower CFM

590

Jumper 1-2

Jumper Pins

Plastic

Jumper

1

3

5

7

2

4

6

8

1

3

5

7

2

4

6

8

1

3

5

7

2

4

6

8

Max. Blower CFM

390

CAUTION:

Hood must be disconnected from main power prior to performing the

conversion instructions listed below. Failure to do so could result in

personal injury or damage to the product.

!

- PC Board is located behind internal cover panel.

5HPRYHEDIÀH¿OWHUV   

- Remove 3 screws attaching internal cover panel.

- Pull down on panel to access PC Board.

FIG. C FIG. D

13

Fan Curve Diagrams

0.90

1.00

1.10

1.20

1.30

1.40

1.50

1.60

1.70

1.80

1.90

2.00

2.10

2.20

2.30

2.40

2.50

2.60

2.70

2.80

Pressure (inAq)

Blower Fan Curve

Model: ZSP

AC Input: 120V, 60Hz

Outlet Diameter: 10in

0.00

0.10

0.20

0.30

0.40

0.50

0.60

0.70

0.80

0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 1000 1050 1100 1150 1200 1250 1300

Flow rate (CFM)

14

www.zephyronline.com

Fan Curve Diagrams

15

VOLTS

HZ

MAX AMPS

120

60

7

ZSP-E36BS

ZSP-E42BS

CIRCUIT DIAGRAM

MOTO R

BLUE

BROWN

GRAY

AC N

TRANS FORMER

WHITE

GRE EN

BLACK

WHITE

BODY

PURPLE

R E MAR K S :C ONDE NS E R 11+11uF 250VAC 2 F IT AC 120V 60Hz

AC L

GRAY

BLUE

BROWN

BODY

GREEN

LOMID

HI

YELLOW

COM

FUSE

YELLOW

RED

WHITE

MOTOR

BODY

GREEN

YELLOW

RED

WHITE

RED

CONTROL

PC

GRAY

BLUE

BROWN

Wiring Diagrams

ACT 590 CFM - Fan Max. 556W @ 4.6A

ACT 390 CFM - Fan Max. 381W @ 3.4A

3RZHUFRQVXPSWLRQVKRZQIRUGHIDXOW&)0EORZHUFRQ¿JXUDWLRQ

VOLTS

HZ

MAX AMPS

120

60

7

ZSP-E48BS

CIRCUIT DIAGRAM

MOTO R

BLUE

BROWN

GRAY

AC N

TR ANSFOR MER

WHITE

GREE N

BLACK

WHITE

BODY

PURPLE

R E MAR K S :C ONDE NS E R 11+11uF 250VAC 2 FIT AC 120V 60Hz

AC L

GRAY

BLUE

BROWN

BODY

GREEN

LO

MID

HI

YELLOW

COM

FUSE

YELLOW

RED

WHITE

MOTO R

BODY

GREEN

YELLOW

RED

WHITE

RED

CONTROL

PC

GRAY

BLUE

BROWN

16

www.zephyronline.com

Troubleshooting

TROUBLESHOOTING PROCEDURES FOR SIENA PRO

Issue Cause What to do

After installation,

the unit doesn’t

work.

1. The power source is not turned ON. 1. Make sure the circuit breaker and the unit’s

power is ON.

2. The power line and the cable locking connector

is not connecting properly.

2. Check the power connection with the unit is

connected properly.

3. The wires on the control board are loose. 3. Make sure the wires on the control board are

connected properly.

4. The switch board and control board wirings are

disconnected.

4. Make sure the wirings between the switch

board and control board are connected

properly.

5. The switch board or control board is defective. 5. Change the switch board or control board.

Light works, but

blower is not

turning.

1. The blower cable is disconnected. 1. Check all wirings from the blower to be sure

all cables are connected properly.

2. The blower is defective, possibly seized. 2. Change the blower.

3. The thermally protected system detects if the

blower is too hot to operate and shuts the blower

down.

3. The blower will function properly after the

thermally protected system cool down.

4. The switch board or control board is defective. 4. Change defective part.

The unit is

vibrating.

1. The motor is not secure in place. 1. Tighten the motor in place.

2. Damaged blower wheel. 2. Replace the blower.

3. The hood is not secured in place. 3. Check the installation of the hood.

The unit is

whistling.

7KH¿OWHULVQRWLQWKHFRUUHFWSRVLWLRQ $GMXVWWKH¿OWHUVXQWLOWKHZKLVWOLQJVWRSV

2. The duct pipe connections are not sealed or

connected properly.

2. Check the duct pipe connections to be sure all

connections are sealed properly.

The blower is

working, but the

lights are not.

1. Defective LED bulb. 1. Change the LED bulb.

2. The LED bulb wire is loose. 2. Check bulb wire connections at the control

board and the light bulbs. Reconnect any

loose wires.

The unit turns on

by itself.

1. A spot light or kitchen lamp is shining directly

onto the switch controls.

1. The switch controls are light sensative. A

direct light source onto the switch controls

may disrupt switch functions.

The speed levels

of the blower

sound the same.

1. Using the wrong size of ducting. 1. Change the ducting to at least 10” or higher.

The hood is

not venting out

properly.

1. The hood might be hanging too high from the

cook top.

1. Adjust the distance between the cook top and

the bottom of the hood within 24” and 34”

range.

2. The wind from the opened windows or opened

doors in the surrounding area are affecting the

ventilation of the hood.

2. Close all the windows and doors to eliminate

WKHRXWVLGHZLQGÀRZ

3. Blockage in the duct opening or ductwork. 3. Remove all the blocking from the duct work or

duct opening.

4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.

5. Using the wrong size of ducting. 5. Change the ducting to at least 10” or higher.

Mesh Filter is

vibrating.

 0HVK¿OWHULVORRVH 1. Make sure the metal clips in the handle are

QRWVWXFN2UUHSODFHWKHPHVK¿OWHU

2. Filter spring clip is loose or broken. 8QLQVWDOODQGUHLQVWDOO¿OWHUSXVKXSRQ¿OWHU

ODWFK5HSODFHPHVK¿OWHULIQHHGHG

17

1-888-880-8368

STAPLE YOUR RECEIPT HERE

TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:

Zephyr Ventilation, LLC (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to

herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials

or workmanship as follows:

Three Year Limited Warranty for Parts: For three years from the date of your original purchase of the Products, we

will provide, free of charge, Products or parts (including LED light bulbs, if applicable) to replace those that failed due to

manufacturing defects. We may choose, in our sole discretion, to repair or replace parts before we elect to replace the

Products.

One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will

provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to

manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs

associated with this warranty.

Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts and

does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and service

required for the Products and consumable parts such as fluorescent, incandescent or halogen light bulbs, mesh and char-

coal filters and fuses; (b) any Products or parts which have been subject to freight damage, misuse, negligence, accident,

faulty installation or installation contrary to recommended installation instructions, improper maintenance or repair (other

than by us); (c) commercial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear

of the finish of the Products or wear caused by improper maintenance, use of corrosive and abrasive cleaning products,

pads, and oven cleaner products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips

to your home to teach you how to use the Products; (g) damage to the Products caused by accident, fire, floods, acts of

God; or (h) Custom installations or alterations that impact serviceability of the Products. If you are outside our service

area, additional charges may apply for shipping costs for warranty repair at our designated service locations and for the

travel cost to have a service technician come to your home to repair, remove or reinstall the Products. After the first year

from the date of your original purchase, you are also responsible for all labor costs associated with this warranty.

Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE AND

EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR

SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCTS.

THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS

WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS,

AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not allow limitations on the duration of an implied

warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not

apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable

implied warranty is limited to the same two-year period described above. Any oral or written description of the Products is for

the sole purpose of identifying the Products and shall not be construed as an express warranty. Prior to using, implementing

or permitting use of the Products, you shall determine the suitability of the Products for the intended use, and you shall assume

all risk and liability whatsoever in connection with such determination. We reserve the right to use functionally equivalent

refurbished or reconditioned parts or Products as warranty replacements or as part of warranty service. This warranty is not

transferable from the original purchaser and applies in the United States and Canada.

To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or

telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identifi-

cation number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the

request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase

date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documenta-

tion to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.

Please check our website for any revisions, www.zephyronline.com.

Zephyr Ventilation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368

Limited Warranty

AUG14.0401

Proof of the original purchase

date is needed to obtain

service under warranty

Warranty

18

www.zephyronline.com

PRODUCT REGISTRATION

Congratulations on your Zephyr range

hood purchase! Please take a moment to

register your new range hood at

www.zephyronline.com/registration

Zephyr Ventilation | 2277 Harbor Bay Pkwy. | Alameda, CA 94502 | 1.888.880.8368

Prompt registration helps in more ways

than one.

IT’S IMPORTANT

Ensures warranty coverage should you

need service.

Ownership verification for insurance

purposes.

Notification of product changes or recalls.

La page est en cours de chargement...

Zephyr ZSPE36BS Mode d'emploi

Zephyr ZSPE36BS Mode d'emploi

dans d''autres langues

Documents connexes