Whirlpool WRS321SDHB Le manuel du propriétaire

Marque: Whirlpool

Modèle: WRS321SDHB

Catégorie: Frigos

Taper: Le manuel du propriétaire

W11484052A

SIDE-BY-SIDE REFRIGERATOR OWNER’S MANUAL

MANUEL D’UTILISATION DU RÉFRIGÉRATEUR CÔTE

À CÔTE

Table of Contents/Table des matières

REFRIGERATOR SAFETY.................................................2

Refrigerator Safety .........................................................2

MAINTENANCE AND CARE ..............................................3

Cleaning ......................................................................3

Lights ..........................................................................3

Freezer Shelf (number varies by model)..............................5

Vacation and Moving Care ...............................................5

INSTALLATION INSTRUCTIONS ........................................5

Unpack the Refrigerator ..................................................5

Location Requirements ...................................................6

Electrical Requirements ..................................................8

Water Supply Requirements.............................................9

Connect Water Supply ....................................................9

Complete the Installation ............................................... 11

Install Air Filter (on some models).................................... 11

Install Produce Preserver (on some models) ...................... 12

REFRIGERATOR FEATURES........................................... 13

Convertible Drawer Temperature Control (on some

models) ..................................................................... 13

Crisper Humidity Control (on some models) ....................... 13

Dual Evaporator (on some models).................................. 13

Water and Ice Dispensers .............................................. 13

Ice Maker and Storage Bin............................................. 13

Water Filtration System ................................................. 15

DOOR REMOVAL AND LEVELING STYLE 1....................... 17

Door Instructions ......................................................... 17

Install and Remove Door Handles ................................... 17

Remove Doors and Hinges ............................................ 18

Replace Doors and Hinges ............................................ 20

Door Closing and Alignment........................................... 21

DOOR REMOVAL AND LEVELING STYLE 2....................... 22

Door Instructions ......................................................... 22

Install and Remove Door Handles ................................... 22

Remove Doors and Hinges ............................................ 22

Door Closing, Leveling, and Alignment ............................. 24

PERFORMANCE DATA SHEET ........................................ 26

SÉCURITÉ DU RÉFRIGÉRATEUR .................................... 28

Sécurité du réfrigérateur................................................ 28

ENTRETIEN ET RÉPARATION ......................................... 29

Nettoyage .................................................................. 29

Lampes ..................................................................... 30

Tablettes du congélateur (le nombre varie selon le

modèle) ..................................................................... 31

Précautions à prendre avant les vacances ou le

déménagement ........................................................... 32

INSTRUCTIONS D’INSTALLATION ................................... 32

Déballage du réfrigérateur ............................................. 32

Exigences d’emplacement ............................................. 33

Spécifications électriques .............................................. 35

Spécifications de l’alimentation en eau ............................. 36

Raccordement à la canalisation d’eau .............................. 36

Terminer l’installation .................................................... 38

Installer le filtre à air (sur certains modèles) ....................... 39

Installation du conservateur de produits frais (sur certains

modèles).................................................................... 39

CARACTÉRISTIQUES DU RÉFRIGÉRATEUR..................... 40

Commande de température dans le tiroir convertible (sur

certains modèles) ........................................................ 40

Commande d’humidité dans le bac à légumes (sur certains

modèles).................................................................... 41

Évaporateur double (sur certains modèles)........................ 41

Distributeurs d’eau et de glaçons..................................... 41

Machine à glaçons et bac d’entreposage........................... 41

Système de filtration de l’eau.......................................... 43

RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU,

STYLE 1 ....................................................................... 45

Instructions pour la porte ............................................... 45

Installation et retrait des poignées de la porte..................... 46

Démontage des portes et charnières................................ 47

Réinstallation des portes et charnières ............................. 48

Fermeture et alignement des portes................................. 49

RETRAIT DE LA PORTE ET AJUSTEMENT DU NIVEAU,

STYLE 2 ....................................................................... 50

Instructions pour la porte ............................................... 50

Installation et retrait des poignées de la porte..................... 51

Démontage des portes et charnières................................ 51

Fermeture, mise à niveau et alignement des portes ............. 53

FICHE DE DONNÉES RELATIVES AU RENDEMENT ........... 55

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

DANGER

You can be killed or seriously injured if you don't

immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions,

including the following:

� Children should be supervised to ensure that they do not

play with the appliance.

� This appliance is not intended for use by persons (including

children) with reduced physical, sensory, or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety.

� Do not use an extension cord.

� If power supply cord is damaged, it must be replaced by the

manufacturer, its service agent, or a similarly qualified

person in order to avoid a hazard.

� Connect to potable water supply only.

� This appliance is intended to be used in household and

similar applications such as: staff kitchen areas in shops,

offices, and other working environments; farm houses and

by clients in hotels, motels, and other residential-type

environments; bed and breakfast-type environments; and

catering and similar non-retail applications.

� Do not store explosive substances such as aerosol cans

with a flammable propellant in this appliance.

� Do not use replacement parts that have not been

recommended by the manufacturer (e.g., parts made at

home using a 3D printer).

� Keep ventilation openings, in the appliance enclosure or in

the built-in structure, clear of obstruction.

� Do not use mechanical devices or other means to

accelerate the defrosting process, other than those

recommended by the manufacturer.

� Do not damage the refrigerant circuit.

� Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type

recommended by the manufacturer.

SAVE THESE INSTRUCTIONS

Proper Disposal of Your Old Refrigerator

WARNING: Risk of child entrapment. Before you throw

away your old refrigerator or freezer:

� Take off the doors.

� Leave the shelves in place so that children may not easily

climb inside.

WARNING

Suffocation Hazard

Remove doors or lid from your old appliance.

Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation

are not problems of the past. Junked or

abandoned refrigerators are still dangerous, even

if they will sit for “just a few days.” If you are getting

rid of your old refrigerator, please follow these

instructions to help prevent accidents.

Important information to know about disposal

of refrigerants:

Dispose of refrigerator in accordance with federal

and local regulations. Refrigerants must be

evacuated by a licensed, EPA-certified refrigerant

technician in accordance with established

procedures.

MAINTENANCE AND CARE

Cleaning

WARNING

Explosion Hazard

Risk of Fire or Explosion.

Flammable Refrigerant Used.

Do Not Use Mechanical Devices to Defrost Refrigerator.

Do Not Puncture Refrigerant Tubing.

Both the refrigerator and freezer sections defrost automatically.

However, clean both sections about once a month to avoid

buildup of odors. Wipe up spills immediately.

IMPORTANT: Because air circulates between both sections, any

odors formed in one section will transfer to the other. You must

thoroughly clean both sections to eliminate odors. To avoid odor

transfer and drying out of food, wrap or cover foods tightly.

NOTE: Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning waxes,

concentrated detergents, bleaches or cleansers containing

petroleum products on plastic parts, interior, and door liners or

gaskets. Do not use paper towels, scouring pads, or other harsh

cleaning tools. Stainless steel models have a coating. Do Not use

regular stainless steel cleaning products. Do Not use stainless

steel cleaner or polish and use only mild soap, water, and soft

microfiber cloth to avoid damage to the stainless steel protective

coating. Paper towels scratch and may dull the clear coat of the

painted door. To avoid possible damage, use only clean cloths to

polish and wipe the door.

1. Unplug refrigerator or disconnect power.

2. Hand-wash, rinse, and dry removable parts and interior

surfaces thoroughly. Use a clean sponge or soft cloth and a

mild detergent in warm water.

3. Wash stainless steel and painted metal exteriors with a clean

sponge or soft cloth and a mild detergent in warm water.

WARNING

Explosion Hazard

Risk of Fire or Explosion due to Puncture of Refrigerant

Tubing;

Follow Handling Instructions Carefully.

Flammable Refrigerant Used.

4. There is no need for routine condenser cleaning in normal

home operating environments. If the environment is

particularly greasy or dusty, or there is significant pet traffic in

the home, the condenser should be cleaned every 2 to 3

months to ensure maximum efficiency.

If you need to clean the condenser:

� Remove the base grille. See the “Door Removal”

instructions, either in the Owner’s Manual or in the

separate instruction sheet provided with your refrigerator.

� Use a vacuum cleaner with a soft brush to clean the grille,

the open areas behind the grille, and the front surface area

of the condenser.

� Replace the base grille when finished.

5. Plug in refrigerator or reconnect power.

Lights

Not all bulbs will fit your refrigerator. Be sure to replace the bulb

with one of the same size, shape, and wattage.

IMPORTANT: The light bulbs in both the refrigerator and freezer

compartments of your new refrigerator may use LED technology.

On some models, the LED light bulbs in the refrigerator, freezer,

air tower, and dispenser cannot be changed by yourself. If the

lights do not illuminate when the refrigerator and/or freezer door is

opened, call for assistance or service. In the U.S.A., call

1-800-253-1301. In Canada, call 1-800-807-6777.

Light Styles:

The dispenser lights are LEDs that cannot be changed.

The interior lights vary by model.

� Some models have mini LEDs that cannot be changed.

� Some models have full-size LED bulbs that can be changed.

To order replacement 2.0 W LED bulbs, use part number

W10574850A, and for 3.6 W, use part number W10565137A,

or call 1-800-253-1301 (U.S.A.) or 1-800-807-6777 (Canada).

2.0 watts 3.6 watts

NOTE: Some LED replacement bulbs are not recommended

for wet/damp environments. The refrigerator and freezer

compartments are considered to be wet/damp environments. If

using a brand of LED bulb other than the recommended

Whirlpool LED bulb, read and follow all instructions on the

replacement bulb’s packaging before installing it.

� Some models have interior incandescent 40 W

bulbs that can be changed.

NOTE: Not all replacement bulbs will fit your

refrigerator. Do not use an incandescent bulb in

excess of 40 watts.

To Change a Light Bulb:

1. Unplug refrigerator or disconnect power.

2. Remove the light shield, as explained in the following

sections.

NOTE: To clean the light shield, wash it with warm water and

liquid detergent. Before reinstalling, thoroughly rinse and dry

the shield.

3. Replace the burned-out light bulb, as explained in the

following sections.

4. Reinstall the light shield, as explained in the following

sections.

5. Plug in refrigerator or reconnect power.

Refrigerator Compartment – Upper Lights

Light Shield Removal:

Slide the light shield toward the rear of the refrigerator and remove

it from the light housing.

Replacement Bulb:

� If the burned-out light is a full-size LED bulb, replace it with a

2.0 W LED bulb.

� If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape, and

wattage (40 W maximum).

Light Shield Reinstallation:

Align the light shield in the grooves at the bottom edge of the light

housing; then slide it forward until it snaps into place.

Refrigerator Compartment – Lower Lights

Light Shield Removal:

Slide the light shield to the right to remove the left end from the

wall slots; then pull the right end out of its wall slots.

Replacement Bulb:

� If the burned-out light is a full-size LED bulb, replace it with a

3.6 W LED bulb.

� If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape, and

wattage (40 W maximum).

Light Shield Reinstallation:

Place the right end of the light shield into the wall slots; then snap

the left end into its wall slots.

Freezer Compartment – Upper Light

Light Shield Removal:

Gently squeeze the front and the bottom-rear edge of the light

shield to release the tabs from the wall slots; then pull the light

shield forward.

Replacement Bulb:

� If the burned-out light is a full-size LED bulb, replace it with a

3.6 W LED bulb.

� If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape, and

wattage (40 W maximum).

Light Shield Reinstallation:

Align the light shield in its proper position, and snap the tabs into

the wall slots.

Freezer Compartment – Lower Light

Light Shield Removal:

Slide the light shield to the left to remove the right end from the

wall slots; then pull the left end out of its wall slots.

Replacement Bulb:

� If the burned-out light is a full-size LED bulb, replace it with a

3.6 W LED bulb.

� If the burned-out light is an incandescent bulb, replace it with

an incandescent appliance bulb of the same size, shape, and

wattage (40 W maximum).

Light Shield Reinstallation:

Place the left end of the light shield into the wall slots; then snap

the right end into its wall slots.

Freezer Shelf (number varies by

model)

To Remove and Replace the Bottom Shelf:

1. Lift up the front and back of the shelf, and remove from the

cabinet. Be sure not to remove the retaining rods.

2. Replace the shelf, aligning the rods with the cabinet ribs.

Apply a little pressure on the shelf to attach the rods to the ribs

of the cabinet.

To Remove and Replace the Mid and Top Shelf:

1. With your hand, push the shelf from bottom to top until it is

released from the holding rod. Pull the shelf until it is released

from the rear rod. Remove from the cabinet.

2. To replace the shelf:

� Replace rods into the support holes. Push the rods down

so they click into the holes.

� Identify the front and rear trim of the shelf.

� Place the rear trim on the rear rod and push the shelf so it

clicks the rod into the rear trim. (Keep the front raised while

pushing.)

� Lower the front of the shelf until the front trim is on the rod

and push the shelf down so it clicks the rod into the front

trim.

NOTE: Be sure that both sides of the shelf are positioned evenly

in the shelf support holes and the shelf is secure.

Vacation and Moving Care

Vacations

If You Choose to Leave Refrigerator On While You Are Away:

1. Use up any perishables and freeze other items.

2. If your refrigerator has an automatic ice maker and is

connected to the household water supply, turn off the water

supply to the refrigerator. Property damage can occur if the

water supply is not turned off.

3. If you have an automatic ice maker, turn off the ice maker.

NOTE: Depending on your model, raise the wire shutoff arm

to Off (up) position or press the switch to Off.

4. Empty the ice bin.

If You Choose to Turn Refrigerator Off Before You Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

� Turn off the water supply to the ice maker at least one day

ahead of time.

� When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position or move the switch to the Off

setting.

3. Depending on the model, turn the refrigerator control to Off or

turn cooling off. See “Control Descriptions” in the Quick Start

Guide.

4. Unplug refrigerator or disconnect power.

5. Clean, wipe, and dry thoroughly.

6. Tape rubber or wood blocks to the tops of both doors to prop

them open far enough for air to get in. This stops odor and

mold from building up.

Moving

When you are moving your refrigerator to a new home, follow

these steps to prepare it for the move.

1. If your refrigerator has an automatic ice maker:

� Turn off the water supply to the ice maker at least one day

ahead of time.

� Disconnect the water line from the back of the refrigerator.

� When the last load of ice drops, raise the wire shutoff arm

to the Off (up) position or move the switch to the Off

setting.

2. Remove all food from the refrigerator and pack all frozen food

in dry ice.

3. Empty the ice bin.

4. Depending on the model, turn the refrigerator control to Off or

turn cooling off. See “Control Descriptions” in the Quick Start

Guide.

5. Unplug refrigerator or disconnect power.

6. Clean, wipe, and dry thoroughly.

7. Take out all removable parts, wrap them well, and tape them

together so they don’t shift and rattle during the move.

8. Depending on the model, raise the front of the refrigerator so it

rolls more easily, or screw in the leveling legs so they don't

scrape the floor. See “Adjust the Doors” or “Door Removal,

Leveling and Alignment” in the online Feature Guide.

9. Tape the doors closed and tape the power cord to the back of

the refrigerator.

When you get to your new home, put everything back and refer to

the Installation Instructions for preparation instructions. Also, if

your refrigerator has an automatic ice maker, remember to

reconnect the water supply to the refrigerator.

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

Remove the Packaging

Dispose of/recycle all packaging materials. Do not use sharp

instruments, rubbing alcohol, flammable fluids, or abrasive

cleaners to remove tape or glue. These products can damage the

surface of your refrigerator. For more information, see

“Refrigerator Safety.”

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the refrigerator for

cleaning or service, be sure to cover the floor with cardboard or

hardboard to avoid floor damage. Always pull the refrigerator

straight out when moving it. Do not wiggle or “walk” the

refrigerator when trying to move it, as floor damage could occur.

IMPORTANT:

� For counter-depth models, use 1/2" socket wrench to remove

skids (socket extension is recommended).

� All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

Clean Before Using

After you remove all of the package materials, clean the inside of

your refrigerator before using it. See the “Cleaning” section in this

manual.

Important information to know about glass shelves and

covers:

Do not clean glass shelves or covers with warm water when they

are cold. Shelves and covers may break if exposed to sudden

temperature changes or impact, such as bumping. Tempered

glass is designed to shatter into many small, pebble-size pieces.

This is normal. Glass shelves and covers are heavy. Use both

hands when removing them to avoid dropping.

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline,

away from appliance.

Use nonflammable cleaner.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

� This refrigerator is designed for indoor household use only.

� Observe all governing codes and ordinances.

� Installer: Leave Owner’s Manual with homeowner.

� Homeowner: Keep Owner’s Manual for future reference and

for the local electrical inspector’s use.

� Keep cardboard shipping piece or plywood under refrigerator

until it is installed in the operating position.

� Comply with installation specifications and dimensions.

� Remove any moldings or decorative panels from kitchen

cabinets that would not allow access to the refrigerator for

service.

� Contact a qualified electrical installer.

For Standard Side-by-Side Installation:

To ensure proper ventilation for your refrigerator, allow for 1/2"

(1.27 cm) of space on each side and at the top. Allow for 2" (5.08

cm) of space behind the refrigerator. If your refrigerator has an ice

maker, allow extra space at the back for the water line

connections. When installing your refrigerator next to a fixed wall,

leave a 2" (5.08 cm) minimum space on each side (depending on

your model) to allow the doors to swing open.

NOTES:

� This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

� Normal minimum cabinet cut-out width required for product

installation is 36" (91.44 cm). However, if the product is placed

against an extended wall and the ability to remove the crisper

pans is desired, an additional 18" (45.72 cm) of cabinet width

is required, so a total cabinet opening width of 54" (137.16 cm)

is recommended.

For Counter-Depth Side-by-Side Installation:

NOTES:

� The refrigerator can be installed into a recessed opening, at

the end of cabinets or as a freestanding refrigerator.

� If you are installing the refrigerator to fit flush with the front of

the base cabinets, all shoe moulding and baseboards must be

removed from the rear of the refrigerator opening. Allow for 1"

(2.54 cm) of space behind the refrigerator.

� Location should permit doors to open fully. See “Product

Dimensions.”

� This refrigerator is intended for use in a location where the

temperature ranges from a minimum of 55°F (13°C) to a

maximum of 110°F (43°C). The preferred room temperature

range for optimum performance, which reduces electricity

usage and provides superior cooling, is between 60°F (15°C)

and 90°F (32°C). It is recommended that you do not install the

refrigerator near a heat source, such as an oven or radiator.

� Floor must support refrigerator weight (more than 600 lbs.

[272 kg]) and contents.

Tools Needed:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

� Cordless drill

� 1/4" nut driver and drill bit

� Flat-blade screwdriver

� Two adjustable wrenches

� 5/16" or adjustable wrench

� 7/16" and 1/2" open-end

wrenches

� 3/8" and 1/2" socket

wrenches

Parts Needed:

� Your refrigerator dealer has a kit available with a 1/4" (6.35

mm) saddle-type shutoff valve, a union, and copper tubing.

� Or you can purchase 1/4" (6.35 mm) copper tubing with shutoff

valve and a 1/4" (6.35 mm) compression fitting (coupling).

� Depending on water line connections, you may also need a

1/4" (6.35 mm) nut and 1/4" (6.35 mm) ferrule.

Product Dimensions – Top View

Door

Style

Depth A Depth B Depth C

Flat 27 1/2"

(69.9 cm)

2 5/8" (6.7 cm)

maximum*

30" (76.2 cm)

maximum*

Curved 28 5/8"

(72.7 cm)

2 5/8" (6.7 cm) 31 1/8" (79.1 cm)

*Dimension may vary based on style of door handle.

The depth for the largest available handle is listed.

Product Dimensions – Front View

Model Size Height A

69" 65 3/4" (167.0 cm)

72" 68 1/8" (173.0 cm)

Product Dimensions – Side View

� Height dimensions are shown with the leveling legs extended

to the minimum height of 1/4" (6.35 mm) below the refrigerator.

NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add 3/4" (19 mm) to the height

dimensions.

� The power cord is 61 1/4" (155.6 cm) long.

� The water line attached to the back of the refrigerator is 78"

(198.1 cm) long.

Model Size Height A Height B Height C

69" 68 7/8"

(174.9 cm)

68 7/8"

(174.9 cm)

68 1/2"

(174.0 cm)

72" 71 1/4"

(181.0 cm)

71 1/4"

(181.0 cm)

71"

(180.3 cm)

Opening Dimensions

� Height dimensions are shown with the leveling legs extended

to the minimum height of 1/4" (6.35 mm) below the refrigerator.

NOTE: When leveling legs are fully extended to 1" (25 mm)

below the refrigerator, add 3/4" (19 mm) to the height

dimensions.

� In the following graphic, “A” represents the opening height

required for standard cabinets. For full-overlay cabinet doors

with a trim kit, add 1/8" (0.3 cm).

� In the following graphic, “B” represents the distance needed to

fully open the freezer door and “C” represents the distance

needed to fully open the refrigerator door.

Model Size

and Door

Style

Height A Width B Width C

69" Flat 69"

(175.3 cm)

13 5/8"

(34.6 cm)

maximum*

18 1/8"

(46.0 cm)

maximum*

72" Flat 72"

(182.9 cm)

71 1/4"

(181.0 cm)

maximum*

18 1/8"

(46.0 cm)

maximum*

69" Curved 69"

(175.3 cm)

13 5/8"

(34.6 cm)

18 3/8"

(46.7 cm)

72" Curved 72"

(182.9 cm)

13 3/4"

(34.9 cm)

18 3/8"

(46.7 cm)

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Door Swing Dimensions

� Location must permit doors to open to a minimum of 165°.

� In the following graphic, “A” represents the distance needed to

fully open the freezer door and “B” represents the distance

needed to fully open the refrigerator door.

Dimension Flat Doors Curved Doors

A 13 5/8" (34.6 cm)

maximum*

13 3/4" (34.9 cm)

B 18 1/8" (46.0 cm)

maximum*

18 3/8" (46.7 cm)

C 2 3/4" (7.0 cm)

maximum*

3 3/4" (9.5 cm)

D 1/8" (0.3 cm) 1 1/4" (3.2 cm)

*Dimension may vary based on style of door handle.

The width for the largest available handle is listed.

Electrical Requirements

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is

important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 V, 60 Hz, AC-only, 15 A or 20 A fused, grounded electrical

supply is required. It is recommended that a separate circuit

serving only your refrigerator be provided. Use an outlet that

cannot be turned off by a switch. Do not use an extension cord.

NOTE: Before performing any type of installation, cleaning, or

removing a light bulb, turn cooling off or turn the control

(thermostat, refrigerator, or freezer control depending on the

model) to Off. Then disconnect the refrigerator from the electrical

source. When you are finished, reconnect the refrigerator to the

electrical source. Turn cooling on or reset the control (thermostat,

refrigerator, or freezer control depending on the model) to the

desired setting. See “Control Descriptions” in the Quick Start

Guide.

Water Supply Requirements

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

Tools Needed:

� Flat-blade screwdriver

� 7/16" and 1/2" open-end or two

adjustable wrenches

� 1/4" nut driver

� 1/4" drill bit

� Cordless drill

NOTE: Your refrigerator dealer has a kit available with a 1/4"

(6.35 mm) saddle-type shutoff valve, a union, and copper or PEX

tubing. Before purchasing, make sure a saddle-type valve

complies with your local plumbing codes. Do not use a piercing-

type or 3/16" (4.76 mm) saddle valve, which reduces water flow

and clogs more easily.

IMPORTANT:

� All installations must meet local plumbing code requirements.

� Use copper or PEX tubing and check for leaks. Install copper

or PEX tubing only in areas where the household temperatures

will remain above freezing.

Water Pressure

A cold water supply with water pressure of between 30 and 120

psi (207 and 827 kPa) is required to operate the water dispenser

and ice maker. If you have questions about your water pressure,

call a licensed, qualified plumber.

If your refrigerator has a water dispenser: After installation is

complete, use the water dispenser to check the water pressure.

� With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less, the

water pressure to the refrigerator meets the minimum

requirement.

� If it takes longer than 8 seconds to dispense 1 cup of water, the

water pressure to the refrigerator is lower than recommended.

See online “Troubleshooting” for suggestions.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the

refrigerator needs to be between 30 and 120 psi (207 and 827

kPa).

If a reverse osmosis water filtration system is connected to your

cold water supply, the water pressure to the reverse osmosis

system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than

40 to 60 psi (276 to 414 kPa):

� Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

� Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

� If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse

osmosis system. Remove the water filter. See “Water Filtration

System”.

If you have questions about your water pressure, call a licensed,

qualified plumber.

Connect Water Supply

Read all directions before you begin.

IMPORTANT:

� Connect to potable water supply only.

� Plumbing shall be installed in accordance with the

International Plumbing Code and any local codes and

ordinances.

� The gray water tubing on the back of the refrigerator (which is

used to connect to the household water line) is a PEX (cross-

linked polyethylene) tube. Copper or PEX tubing connections

from the household water line to the refrigerator are

acceptable, and will help avoid off-taste or odor in your ice or

water. Check for leaks. For recommended parts if PEX tubing

is used instead of copper:

W10505928RP (7 ft. [2.14 m] jacketed PEX),

8212547RP (5 ft. [1.52 m] PEX), or

W10267701RP (25 ft. [7.62 m] PEX).

� Install tubing only in areas where temperatures will remain

above freezing.

Tools Needed:

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

� Flat-blade screwdriver

� 7/16" and 1/2" open-end wrenches or two adjustable wrenches

� 1/4" nut driver

Connect to Water Line

IMPORTANT: If you turn on the refrigerator before the water line is

connected, turn off the ice maker.

Style 1 (Recommended)

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Use a quarter-turn shutoff valve or the equivalent, served by a

1/2" copper or PEX household supply line.

NOTE: To allow sufficient water flow to the refrigerator, a

minimum 1/2" size copper or PEX household supply line is

recommended.

A. Bulb

B. Nut

C. Copper or PEX tubing (to refrigerator)

D. Household supply line (½" minimum)

4. Now you are ready to connect the copper or PEX tubing to the

shutoff valve. Use 1/4" (6.35 mm) O.D. (outside diameter) soft

copper or PEX tubing to connect the shutoff valve and the

refrigerator.

� Ensure that you have the proper length needed for the job.

Be sure both ends of the copper tubing are cut square.

� Slip compression sleeve and compression nut onto copper

tubing as shown. (PEX tubing has compression sleeves

and compression nuts preinstalled.) Insert end of tubing

into outlet end squarely as far as it will go. Screw

compression nut onto outlet end with adjustable wrench.

Do not overtighten.

A. Compression sleeve

B. Compression nut

C. Copper or PEX tubing

5. Place the free end of the tubing into a container or sink, and

turn on main water supply to flush out tubing until water is

clear. Turn off shutoff valve on the water pipe.

NOTE: Always drain the water line before making the final

connection to the inlet of the water valve, to avoid possible

water valve malfunction.

6. Bend the copper or PEX tubing to meet the water line inlet,

which is located on the back of the refrigerator cabinet. Leave

a coil of copper or PEX tubing to allow the refrigerator to be

pulled out of the cabinet or away from the wall for service.

Style 2

1. Unplug refrigerator or disconnect power.

2. Turn off main water supply. Turn on nearest faucet long

enough to clear line of water.

3. Locate a 1/2" (1.27 cm) to 1 1/4" (3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

� Make sure it is a cold water pipe.

� Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from

the drill and normal sediment from collecting in the valve.

4. Determine the length of copper or PEX tubing you need.

Measure from the connection on the lower rear corner of

refrigerator to the water pipe. Add 7 ft. (2.1 m) to allow for

cleaning. Use 1/4" (6.35 mm) O.D. (outside diameter) copper

or PEX tubing. Be sure both ends of copper or PEX tubing are

cut square.

5. Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold

water pipe you have selected.

A. Cold water pipe

B. Pipe clamp

C. Copper or PEX tubing

D. Compression nut

E. Compression sleeve

F. Shutoff valve

G. Packing nut

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)

drilled hole in the water pipe and that the washer is under the

pipe clamp. Tighten the packing nut. Tighten the pipe clamp

screws slowly and evenly so the washer makes a watertight

seal. Do not overtighten, or you may crush the copper or PEX

tubing.

7. Slip compression sleeve and compression nut onto copper

tubing as shown. (PEX tubing has compression sleeves and

compression nuts preinstalled.) Insert end of tubing into outlet

end squarely as far as it will go. Screw compression nut onto

outlet end with adjustable wrench. Do not overtighten.

8. Place the free end of the tubing in a container or sink, and turn

on the main water supply. Flush the tubing until water is clear.

Turn off the shutoff valve on the water pipe. Coil the tubing.

Connect to Refrigerator

Style 1

1. Unplug refrigerator or disconnect power.

2. Remove and discard the short, black plastic part from the end

of the water line inlet.

3. Thread the nut onto the end of the tubing. Tighten the nut by

hand. Then tighten it with a wrench two more turns. Do not

overtighten.

NOTE: To avoid rattling, be sure the copper tubing does not

touch the cabinet’s side wall or other parts inside the cabinet.

A. Household water line

B. Nut (purchased)

C. Ferrule (purchased)

D. Refrigerator water tubing

4. Install the water supply tube clamp around the water supply

line to reduce strain on the coupling.

5. Turn shutoff valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Style 2

1. Unplug refrigerator or disconnect power.

2. Remove and discard the plastic part that is attached to the

inlet of the water valve.

3. Attach the copper or PEX tube to the valve inlet using a

compression nut and sleeve as shown. Tighten the

compression nut. Do not overtighten.

A. Tube clamp

B. Tube clamp screw

C. Copper tubing

D. Compression nut

E. Valve inlet

4. Use the tube clamp on the back of the refrigerator to secure

the tubing to the refrigerator as shown. This will help avoid

damage to the tubing when the refrigerator is pushed back

against the wall.

5. Turn shutoff valve on.

6. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the 1/4" (6.35 mm) water line at either tube

connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a 1/4" x 1/4" (6.35 mm x 6.35 mm) coupling is needed

in order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper or PEX tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

A. Refrigerator water

tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

4. Turn shutoff valve on.

5. Check for leaks. Tighten any connections (including

connections at the valve) or nuts that leak.

Complete the Installation

WARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Plug into a grounded 3–prong outlet.

2. Wait a few minutes. Check that the compressor is operating

properly and that all lights are working.

NOTE: If the refrigerator does not operate, check that the

circuit breaker is not tripped or that the household fuse has not

blown.

3. Flush the water system. See “Water and Ice Dispensers.”

NOTE: Allow 24 hours to produce the first batch of ice. Allow

72 hours to completely fill ice container.

IMPORTANT: If construction will continue after refrigerator has

been installed, unplug refrigerator or disconnect power.

Install Air Filter (on some models)

On some models, your refrigerator's accessory packet includes an

air filter, which must be installed prior to use. On some models,

the air filter is already installed at the factory. To order a

replacement air filter, use part number W10311524.

The air filter reduces the buildup of odors. This helps to maintain a

cleaner environment inside the refrigerator.

Installing the Air Filter

The filter should be installed behind the vented door, which is

located (depending on your model) along either the rear or left

interior wall near the top of the refrigerator compartment.

1. Remove the air filter from its packaging.

2. Lift open the vented door.

3. Snap the filter into place.

4. Close the vented door.

Installing the Filter Status Indicator (on some

models)

The filter comes with a status indicator, which should be activated

and installed at the same time the air filter is installed.

1. Place the indicator facedown on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Lift open the vented air filter door. On some models, there are

notches behind the door.

4. On models with notches:

� Slide the indicator down into the notches, facing outward.

NOTE: The indicator will not easily slide into the notches if

the rear bubble has not been popped.

� Close the air filter door, and check that the indicator is

visible through the rectangular hole in the door.

On models without notches:

� Place the indicator in a visible place you will easily

remember—either inside the refrigerator or elsewhere in

your kitchen or home.

Replacing the Air Filter

The disposable air filter should be replaced every 6 months, when

the status indicator has completely changed from white to red.

To order a replacement air filter, see ordering information in the

Quick Start Guide.

1. Remove the old air filter by squeezing in on the side tabs.

2. Remove the old status indicator.

3. Install the new air filter and status indicator using the

instructions in the previous sections.

Install Produce Preserver (on some

models)

Your refrigerator's accessory packet includes a Produce

Preserver, which should be installed prior to use. On some

models, the Produce Preserver is already installed at the factory.

To order a replacement produce preserver, use part number

W10346771.

The Produce Preserver absorbs ethylene, allowing the ripening

process of many produce items to slow down. As a result, certain

produce items will stay fresh longer.

Ethylene production and sensitivity varies depending on the type

of fruit or vegetable. To preserve freshness, it is best to separate

produce with sensitivity to ethylene from fruits that produce

moderate to high amounts of ethylene.

Sensitivity to

Ethylene

Production

Apples High Very High

Asparagus Medium Very Low

Berries Low Low

Broccoli High Very Low

Cantaloupe Medium High

Carrots Low Very Low

Citrus Fruit Medium Very Low

Grapes Low Very Low

Lettuce High Very Low

Pears High Very High

Spinach High Very Low

Installing the Produce Preserver

CAUTION: IRRITANT. MAY IRRITATE EYES AND SKIN.

DANGEROUS FUMES FORM WHEN MIXED WITH OTHER

PRODUCTS.

MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES FORM

WHEN MIXED WITH OTHER PRODUCTS.

Do not mix with cleaning products containing ammonia, bleach, or

acids. Do not get in eyes, on skin or clothing. Do not breathe dust.

Keep out of reach of children.

FIRST AID TREATMENT: Contains potassium permanganate. If

swallowed, call a Poison Control Center or doctor immediately. Do

not induce vomiting. If in eyes, rinse with water for 15 minutes. If

on skin, rinse with water.

The Produce Preserver pouches should be installed in their

housing, which is located along an interior side wall of the crisper

or convertible drawer.

NOTE: For best performance, always use two pouches.

1. Remove the Produce Preserver pouches from their

packaging.

2. Lift up on the housing in order to remove it from its mounting

tab along the wall.

3. Open the housing by pulling up and out on the back of the top

of the housing.

4. Place both pouches inside the housing; then snap the housing

back together.

5. Place the housing back on the mounting tab along the wall.

Installing the Status Indicator

The Produce Preserver comes with a status indicator, which

should be activated and installed at the same time the pouch is

installed.

1. Place the indicator facedown on a firm, flat surface.

2. Apply pressure to the bubble on the back of the indicator, until

the bubble pops to activate the indicator.

3. Slide open the cap on the Produce Preserver housing.

4. Place the indicator in the top of the housing, facing outward.

5. Slide the cap closed, and check that the indicator is visible

through the rectangular hole in the cap.

NOTE: The cap will not close easily if the indicator’s rear

bubble has not been popped.

Replacing the Produce Preserver Pouches

The disposable pouches should be replaced every 6 months,

when the status indicator has completely changed from white to

red.

To order replacements, see the contact information in the Quick

Start Guide. Order part number W10346771A or FRESH1.

1. Remove the used pouches from the produce preserver

housing.

2. Remove the old status indicator.

3. Install the new pouches and status indicator using the

instructions in the previous sections.

REFRIGERATOR FEATURES

Convertible Drawer Temperature

Control (on some models)

The control can be adjusted to properly chill meats or vegetables.

The air inside the pan is cooled to avoid “spot” freezing and can

be set to keep meats at the National Livestock and Meat Board

recommended storage temperatures of 28° to 32°F (–2° to 0°C).

To store meat:

Set the control to one of the three Meat settings to store meat at

its optimal storage temperature.

To store vegetables:

Set the control to Veg to store vegetables at their optimal storage

temperatures.

NOTE: If food starts to freeze, move the control to the right (less

cold), toward the Veg setting. Remember to wait 24 hours

between adjustments.

Crisper Humidity Control (on some

models)

You can control the amount of humidity in the moisture-sealed

crisper. Adjust the control to any setting between Low and High.

LOW (open) for best storage of fruits and vegetables with skins.

HIGH (closed) for best storage of fresh, leafy vegetables.

Dual Evaporator (on some models)

Some models come equipped with a dual sequential evaporation

system which includes two separate evaporators for the

refrigerator and freezer compartments.

Dual evaporation results in higher humidity, which helps keep

foods in the refrigerator from spoiling as quickly and improves

food quality and freshness in the freezer due to decreased freezer

burn. In addition, the dual evaporation system helps keep food

smells in the refrigerator from transferring to ice in the freezer.

NOTE: The dual evaporation system is always activated when

your refrigerator is operating. You do not need to press any

buttons to turn it on.

Water and Ice Dispensers

On how to use your water and ice dispensers, see the online

“Side-by-Side Refrigerator Dispensers” Feature Guide.

NOTES:

� Connect to potable water supply only.

� The dispensing system will not operate when either door

(refrigerator or freezer) is open.

� Allow 24 hours for the refrigerator to cool down and chill water.

� Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced. Wait 72 hours for full ice

production.

� On some models, the display screen on the dispenser control

panel will turn off automatically and enter “sleep” mode when

the control buttons and dispenser pads have not been used for

2 minutes or more. While in “sleep” mode, the first press of a

control button will only reactivate the display screen, without

changing any settings.

Flush the Water System

Air in the water dispensing system can cause the water dispenser

to drip. After connecting the refrigerator to a water source or

replacing the water filter, flush the water system. Flushing the

water dispensing system forces air from the water line and filter

and prepares the water filter for use.

NOTE: As air is cleared from the system, water may spurt out of

the dispenser.

1. Using a sturdy container, depress and hold the water

dispenser pad for 5 seconds; then release it for 5 seconds.

2. Repeat step 1 until water begins to flow.

3. Once water begins to flow, continue depressing and releasing

the dispenser pad (5 seconds on, 5 seconds off) until a total of

3 gal. (12 L) has been dispensed.

Additional flushing may be required in some households.

The Water Dispenser

IMPORTANT:

Dispense at least 1 qt. (1 L) of water every week to maintain a

fresh supply.

If the flow of water from the dispenser decreases, it could be

caused by low water pressure.

� With the water filter removed, dispense 1 cup (237 mL) of

water. If 1 cup of water is dispensed in 8 seconds or less, the

water pressure to the refrigerator meets the minimum

requirement.

� If it takes longer than 8 seconds to dispense 1 cup of water, the

water pressure to the refrigerator is lower than recommended.

See “Water Supply Requirements” or online “Troubleshooting”

for suggestions.

Ice Maker and Storage Bin

� Allow 24 hours to produce the first batch of ice. Discard the

first three batches of ice produced.

� The quality of your ice will be only as good as the quality of the

water supplied to your ice maker. Avoid connecting the ice

maker to a softened water supply. Water softener chemicals

(such as salt) can damage parts of the ice maker and lead to

poor quality ice. If a softened water supply cannot be avoided,

make sure the water softener is operating properly and is well

maintained.

� Do not use anything sharp to break up the ice in the storage

bin. This can cause damage to the ice container and the

dispenser mechanism.

� Do not store anything on top of or in the ice maker or storage

bin.

Style 1

Turning the Ice Maker On/Off:

The On/Off switch, located on the left wall of the freezer door, can

only be accessed when the ice storage bin has been removed.

See the following section for bin removal instructions.

� To turn on the ice maker, flip the switch to the On (up) position.

� To manually turn off the ice maker, flip the switch to the Off

(down) position.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes

will raise the shutoff arm to the Off (arm up) position. When the

storage bin is at full capacity, the ice maker will automatically stop

ice production, but the ice maker On/Off switch will remain in the

On (up) position.

Ice production Off

(Shutoff arm up)

Ice production On

(Shutoff arm down)

Removing and Replacing the Ice Storage Bin:

1. Press down the release lever and tilt the bucket outward. Use

both hands to hold the base of the storage bin, and then lift it

up and out.

A. Release lever

NOTE: It is not necessary to flip the ice maker On/Off switch

to the Off (down) position when removing the storage bin. The

storage bin sensor, located on the left wall (right wall on some

models) of the freezer door, stops the ice maker from

producing ice if the door is open or the storage bin is removed.

A. On/Off switch B. Storage bin sensor

2. Replace the bin by sliding it onto the door, and then tilting it

back into an upright position. The release lever will click when

the bin is securely in place.

Style 2

Turning the Ice Maker On/Off:

� To turn on the ice maker, lower the wire shutoff arm to the On

position.

� To manually turn off the ice maker, lift the wire shutoff arm to

the Off (arm up) position and listen for the click. Ice can still be

dispensed, but no more can be made.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes

will raise the wire shutoff arm to the Off (arm up) position. Do not

force the wire shutoff arm up or down.

Removing and Replacing the Ice Storage Bin:

1. Pull the covering panel up from the bottom.

2. Lift the wire shutoff arm so it clicks into the Off (up) position.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser

will not work.

5. To restart ice production, lower the wire shutoff arm to the On

(down) position. Make sure the door is closed tightly.

Style 3

Turning the Ice Maker On/Off:

� To turn on the ice maker, lift open the ice maker door and lower

the wire shutoff arm to the On position.

� To manually turn off the ice maker, lift the wire shutoff arm to

the Off (arm up) position and listen for the click. Ice can still be

dispensed, but no more can be made.

NOTE: The ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes

will raise the wire shutoff arm to the Off (arm up) position. Do not

force the wire shutoff arm up or down.

Removing and Replacing the Ice Storage Bin:

1. Lift and hold open the ice maker door.

2. Lift the wire shutoff arm so it clicks into the Off (up) position.

Release the ice maker door.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser

will not work.

5. To restart ice production, lift open the ice maker door and push

the wire shutoff arm down to the On position.

Style 4

Turning the Ice Maker On/Off:

The On/Off switch is located on the bottom of the ice maker, which

can be accessed by lifting and opening the ice maker door.

� To turn on the ice maker, lift open the ice maker door, and flip

the switch to the On (right) position.

� To manually turn off the ice maker, lift open the ice maker door,

and flip the switch to the Off (left) position. Ice can still be

dispensed, but no more can be made.

NOTE: Your ice maker has an automatic shutoff to keep the

storage bin from overfilling during normal operation. As ice is

made, the ice cubes will fill the ice storage bin, and the ice cubes

will raise the shutoff arm to the Off (arm up) position. When the

storage bin is at full capacity, the ice maker will automatically stop

ice production, but the ice maker On/Off switch will remain in the

On (up) position.

Removing and Replacing the Ice Storage Bin:

1. Pull the covering panel up from the bottom.

2. Lift the plastic shutoff arm so it clicks into the Off (up) position.

3. Lift up the front of the storage bin and pull it out.

4. Replace the bin by pushing it in all the way or the dispenser

will not work.

5. To restart ice production, lower the plastic shutoff arm to the

On (down) position. Make sure the door is closed tightly.

Water Filtration System

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after the

system. Systems certified for cyst reduction may be used on

disinfected waters that may contain filterable cysts.

Water Filter Status Light

The water filter status light will help you know when to change

your water filter. This is located on the refrigerator control panel.

To order a replacement water filter use part number W10295370A

(P4RFWB).

Style 1 – Order and Replace status:

� When the dispenser control panel’s water filter status display

changes to “Order,” this tells you that it is almost time to

change the water filter cartridge.

� Replace the water filter cartridge when the water filter status

display changes to “Replace.”

NOTE: If water flow to your water dispenser or ice maker

decreases noticeably, change the filter sooner. The filter

should be replaced at least every 6 months, depending on

your water quality and usage.

Style 2 – Red light status:

� When the light turns red on the control panel, this tells you that

it is time to change the water filter cartridge.

� It is recommended that you replace the filter when the status

light turns red or water flow to your water dispenser or ice

maker decreases noticeably.

NOTE: The filter should be replaced at least every 6 months,

depending on your water quality and usage.

Resetting the Filter Status

After changing the water filter, reset the status light.

� For models with the Options button:

Press the Options button to enter Options mode, press Lock to

initiate the reset, and then press Measured Fill to confirm that

you want to reset the status light. When the system is reset,

the “Order” and “Replace” icons will disappear from the display

screen.

� For models with the Filter button:

Press and hold the Filter button for 3 seconds to reset the

status light. When the system is reset, the “Order” and

“Replace” icons will disappear from the display screen.

� For models with the Temp Setting button:

The reset button is located on the control panel in the

refrigerator compartment. To reset the status light after

changing the filter, press Temp Setting within 3 seconds. The

status light will change from red to off when the system is

reset.

� For models with the Light and Ice Type buttons:

Reset the filter status light by pressing and hold Light and Ice

Type buttons for 3 seconds. The status light will turn off when

the system is reset.

Changing the Water Filter

Style 1 – Top-right corner location:

1. Locate the water filter in the top-right corner of the refrigerator

compartment.

2. Lift open the filter cover door. The filter will be released and

then be ejected as the door is opened.

3. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

4. Take the new filter out of its packaging and remove the cap.

Be sure the O-rings are still in place after the cap is removed.

A. Cap B. O-rings

5. With the arrow pointing up, align the new filter with the filter

housing and slide it into place. The filter cover door will

automatically begin to close as the new filter is inserted.

6. Close the filter cover door completely in order to snap the filter

into place. You may need to press hard.

7. After changing the filter, reset the filter status light.

8. Flush the water system. See “Water and Ice Dispensers” for

details.

Style 2 – Base grille location (automatic ejection):

A. Water filter cover door

1. Locate the water filter cover door in the base grille, and pull

open the filter door. The filter will be released and then be

ejected as the door is opened.

2. When the door is completely open, pull the filter straight out.

NOTE: There may be some water in the filter. Some spilling

may occur. Use a towel to wipe up any spills.

3. Take the new filter out of its packaging and remove the covers

from the O-rings. Be sure the O-rings are still in place after the

covers are removed.

4. With the arrow pointing to the left (toward the filter cover

door’s hinge), align the new filter with the filter housing and

slide into place. The filter cover door will automatically begin to

close as the new filter is inserted.

5. Close the filter cover door completely in order to snap the filter

into place. You may need to press hard.

6. Flush the water system. See “Water and Ice Dispensers” for

details.

Style 3 – Base grille location (manual turn):

A. Water filter cover door

1. Locate the water filter cover door in the base grille, and pull

open the filter door.

2. Twist the water filter and turn 90° counterclockwise to unlock.

3. Pull the filter out of the housing.

4. Remove the water filter cap from the water filter.

5. Install the water filter cap onto the new filter. Be sure to align

the arrows so the grooves in the filter align with ribs in the filter

cap.

6. Insert the filter into the housing.

7. Twist the water filter and turn 90° clockwise until it locks into

place and the arrows are aligned.

8. Push the water filter door closed.

DOOR REMOVAL AND LEVELING

STYLE 1

Door Instructions

Gather the required tools and parts and read all instructions

before starting installation. Save these instructions for future

reference.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so could result in death or electrical shock.

NOTE: Before moving your refrigerator into your home, measure

the doorway of your home to see whether you need to remove the

refrigerator and freezer doors. If door removal is necessary, see

the instructions below.

TOOLS NEEDED Depending on your model, you may need the

following: Bubble level, flat-blade screwdriver, Phillips screwdriver

tip #2 with 4” long as minimum, 3/16" hex key, 1/4", 3/8”, and 5/16”

hex-head socket wrench, 1/4" and 5/16" open-ended wrenches or

adjustable wrench, internal star drive or 3/8" hex-head socket

wrench, TORX T30 screwdriver.

Install and Remove Door Handles

Refrigerator Door Handle Style 1

PARTS INCLUDED: Door handles (2).

To Install the Handles:

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws.

A. Shoulder screws

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, push downward until the handle is

released from the shoulder screw.

5. Open the refrigerator door and close the freezer door. Repeat

steps 2 through 4 to install the other handle onto the freezer

door

To Remove the Handles:

1. While holding the handle, push upward until the handle is

released from the shoulder screw.

2. Gently pull the handle away from the door.

3. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

Refrigerator Door Handle Style 2

PARTS INCLUDED: Door handles(2), 1/8” hex key, spare

setscrew(s)

NOTE: The handle mounting setscrews are pre-installed in the

handle.

1. Remove the handles, which are packed inside the refrigerator.

NOTE: To avoid scratching the finish, place the handles on a

towel or other soft surface.

2. Open the freezer door. On the refrigerator door, place the

handle on the shoulder screws with the setscrews facing the

freezer.

A. Shoulder screws B. Setscrews inside the

handle

3. Firmly push the handle toward the door until the handle base

is flush against the door.

4. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

5. Using a clockwise motion, tighten the setscrew until it begins

to contact the shoulder screw.

6. Repeat steps 4 and 5 to begin fastening the lower setscrew.

7. Once both setscrews have been partially tightened as outlined

in the previous steps, fully tighten both the upper and lower

setscrews.

IMPORTANT: When the screws feel tight, tighten them an

additional quarter-turn. The handle is not properly installed

without this extra tightening.

8. Open the refrigerator door and close the freezer door. Repeat

steps 2 through 7 to install the other handle onto the freezer

door with the setscrews facing the refrigerator.

9. Save the hex key and all instructions.

To Remove the Handles:

1. While holding the handle, insert the short end of the hex key

into the upper hole and slightly rotate the hex key until it is

engaged in the setscrew.

2. Using a counterclockwise motion, loosen the setscrew a

quarter-turn at a time.

3. Repeat steps 1 and 2 for the upper setscrew. Gently pull the

handle away from the door.

4. If necessary, use a Phillips screwdriver to remove the shoulder

screws from the door.

Remove Doors and Hinges

If your refrigerator does not fit through the doorway or you are

getting rid of your old refrigerator, follow the steps below for door

removal.

WARNING

Electrical Shock Hazard

Disconnect power before removing doors.

Failure to do so could result in death or electrical shock.

1. Unplug refrigerator or disconnect power.

2. Fully open both doors.

3. If your model has water dispensing, please open the water

filter door by pulling it toward you as shown below. It is not

necessary to remove the water filter itself.

4. Pull the base grille toward you from the sides and then from

the center until it dislodges.

5. To remove the base grille, twist and pull the right side until this

side passes underneath the refrigerator door. Then pull the left

side of the base grille for complete removal.

6. If your model has water dispensing in the door, disconnect the

water dispenser tubing located below the freezer door.

� Press the blue outer ring against the face of fitting and pull

the dispenser tubing free as shown below.

NOTE: Keep the water tubing connector attached to the

tube that runs underneath the freezer. The door cannot be

removed if the connector is still attached to the tube that

runs through the door hinge.

A. Face of fitting

7. If your model has water dispensing in the door, disconnect the

wiring located below the freezer door as shown below.

� Remove the wiring clip and the bracket wire using a 1/4"

hexagonal-head socket wrench.

� Disconnect the wiring plugs from the bracket wire.

A. Wiring plugs C. Grommets

B. Wiring clip

8. Close the freezer door and use a TORX T30 screwdriver to

remove the top hinge completely as shown below.

A. Do Not Remove Screws

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

9. Lift the freezer door straight up off from the bottom hinge as

shown below. The water dispenser tubing and wiring will

remain attached to the freezer door.

WARNING

Excessive Weight Hazard

Use two or more people to lift the appliance door.

Failure to do so can result in back or other injury.

NOTE: This may require two people, one to lift the door and

the other to feed the water tubing and wiring into the bottom

hinge pin.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This

will help to avoid scratching or damaging the door, water

tubing, and wiring.

10. Close the freezer door and use a TORX T30 screwdriver to

remove the top hinge completely as shown below.

A. Do not remove screws.

IMPORTANT: Do not remove either screw A. Hold the door

while hinge is being removed.

11. .Lift the refrigerator door straight up off from the bottom hinge

as shown below.

IMPORTANT: Rest the door on its side on a soft, clean

surface, such as a towel, blanket, or piece of cardboard. This

will help to avoid scratching or damaging the door.

12. If your refrigerator without doors does not pass through the

doorway, you may remove both bottom hinges. Use a 5/16"

nut driver to remove these as shown below..

B. Do not remove B screws

IMPORTANT: Do not remove either screw B.

Replace Doors and Hinges

If your doors and bottom hinges have been removed, please

follow the next instructions for reinstallation:

1. Reinstall both bottom hinges using a 5/16" nut driver to tighten

screws as shown below.

B. Do not remove B screws

2. If your model has water dispensing in the door:

� Lift the freezer door enough to feed the water dispenser

tubing and wiring through the bottom hinge pin as shown

below.

NOTE: This may require two people, one to lift the door

and the other to feed the water tubing and wiring into the

bottom hinge pin.

IMPORTANT: Hold the door while hinge is being installed.

3. Close the freezer door to align and reinstall the top hinge. Use

a TORX T30 screwdriver to tighten the screws as shown

below.

A. Do not remove A screws

IMPORTANT: Provide additional support for the door while top

hinge is being reinstalled. Do not depend on the door magnets

to secure the door to the cabinet.

4. If your model has water dispensing in the door, connect the

water dispenser tubing. For the connection, push the tubing

into the dispenser tubing until black mark touches the face of

fitting as shown below.

A. Face of fitting

5. Connect the wiring as shown below.

A. Wiring plugs C. Grommets

B. Wiring clip

6. Reinstall the wiring clip & the bracket wire using a 1/4"

hexagonal head socket wrench.

7. Connect the wiring plugs from the bracket wire.

8. Lift the refrigerator door enough to insert the door onto the

bottom hinge pin as shown below.

IMPORTANT: Hold the door while hinge is being installed.

La page charge ...

Whirlpool WRS321SDHB Le manuel du propriétaire

Marque: Whirlpool

Modèle: WRS321SDHB

Catégorie: Frigos

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WRS321SDHB Owner's manual

Whirlpool WRS321SDHB Le manuel du propriétaire

Whirlpool WRS321SDHB Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents