Indesit AQ9D 69 U (EX)/V Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
EN
1
English,1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
Technical data
Description of the machine, 4-5
Touch control panel
Running a wash cycle, 6
Wash cycles and options, 7
Table of wash cycles
Wash options
Detergents and laundry, 8
Detergent
Preparing the laundry
Washing recommendations
Precautions and advice, 9
General safety
Load balancing system
Disposal
Opening the porthole door manually
Care and maintenance, 10
Cutting off the water and electricity supplies
Cleaning the machine
Cleaning the detergent dispenser drawer
Caring for your appliance drum
Cleaning the pump
Checking the water inlet hose
Trouble shooting, 11
Assistance, 12
EN
WASHING MACHINE
AQUALTIS
AQ9D 69 U
Instructions for
installation and use
F
Français,13
EN
2
Installation
This instruction manual should be kept in a safe place
for future reference. If the washing machine is sold,
given away or moved, please ensure the manual is kept
with the machine, so that the new owner may benefit
from the advice contained within it.
Read these instructions carefully: they contain vital
information relating to the safe installation and operation
of the appliance.
Inside the pack containing this manual, you will also
find the guarantee and all the details necessary for
installation.
Unpacking and levelling
Unpacking
1. Once you have removed all the packaging from the
washing machine, make sure it has not been damaged
during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Remove the 4
protective screws (used
during transportation) and
the corresponding spacer,
located on the rear part of
the appliance (see figure).
3. Close off the holes using the plastic plugs supplied in
the pack.
4. Keep all the parts in a safe place; they will be needed
again if the washing machine is moved to another
location, to prevent the inside of the appliance being
damaged.
Packaging materials should not be used as toys for
children.
Levelling
1. Place the washing machine on a flat sturdy floor,
without resting it up against walls or cabinets.
2. If the floor is uneven,
the front feet of the
machine may be adjusted
until it reaches a horizontal
position (the angle of
inclination must not
exceed 2 degrees).
If the appliance is levelled correctly, it will be more
stable and much less likely to cause vibrations and noise
while it is operating, particularly during the spin cycle.
If it is placed on carpet or a rug, adjust the feet in such
a way as to allow a sufficient ventilation space
underneath the washing machine.
Connecting the electricity and water
supplies
Connecting the water inlet hose
Before connecting the inlet hose to the water supply,
run the water until it is perfectly clear.
1. Connect the inlet hose
to the machine by
screwing it onto the cold
water inlet of the
appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
2. Connect the inlet hose
by screwing it to a cold
water tab using a 3/4 gas
threaded connection (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical data table (see next
page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand or old inlet hoses; use the
products supplied with the machine.
EN
3
Technical data
Model
AQ9D 69 U
Dimensions
width 59,5 cm
height 85 cm
depth 64,5 cm
Capacity
from 1 to 9 kg
Electrical
connections
please refer to the technical data
plate fixed to the machine
Water connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 62 litres
Spin speed
up to 1600 rotations per minute
Energy rated
programmes
according to
regulation
EN 60456
programme ; temperature 60°C;
using a load of 9 kg.
This appliance conforms to the
following EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2006/95/EC (Low Voltage)
- 2002/96/EC
65 - 100 cm
Connecting the drain hose
Connect the drain hose to
drain duct piping or a wall
drain located between 65
and 100 cm above the
floor, making sure it is not
bent at all.
Alternatively, rest the drain
hose on the side of a
washbasin or bathtub,
fastening the duct
supplied to the tap (see
figure).
The free end of the hose
should not be underwater.
We advise against the use of hose extensions; if it is
absolutely necessary, the extension must have the same
diameter as the original hose and must not exceed 150
cm in length.
Electrical connections
Before plugging the appliance into the electricity socket,
make sure that:
the socket is earthed and complies with all applicable
laws;
the socket is able to withstand the maximum power
load of the appliance as indicated in the Technical
data table (see opposite);
the power supply voltage falls within the values
indicated in the Technical data table (see opposite);
the socket is compatible with the plug of the
appliance. If this is not the case, have the socket or
the plug replaced.
The machine must not be installed outdoors, even in
covered areas. It is extremely dangerous to leave the
appliance exposed to rain, storms and other weather
conditions.
The mains socket must remain within easy reach after
the washing machine has been installed.
Do not use extension cords or multiple sockets.
The cable should not be bent or compressed.
The power supply cable and plug must only be
replaced by authorised technicians.
Warning! The company shall not be held responsible in
the event that these regulations are not respected.
EN
4
CONTROL
PANEL
1
2
Description of the machine
PORTHOLE DOOR
Always use the handle to
open the porthole door (see
figure).
DETERGENT DISPENSER DRAWER
The detergent dispenser
drawer is located inside the
machine and can be
accessed by opening the
door.
For more information on
detergent measures, please
refer to the chapter entitled
Detergents and laundry.
Note: stick the label showing
the wash cycle descriptions and options on the front of
the detergent dispenser drawer. You will find the sticker
in the pack containing this manual.
1. pre-wash compartment:
use powder detergent.
2. main wash compartment:
use powder or liquid
detergent. If using the latter
type of detergent, we
recommend it is poured into
the drawer immediately
before you start the washing
machine.
washing additives compartment: for fabric softener or
liquid additives. We recommend that the maximum level
indicated by the grille is not exceeded, and that
concentrated fabric softeners are diluted.
TOUCH CONTROL PANEL
To adjust the settings, gently
press the icon inside the
sensitive (touch control) area
as illustrated in the figure.
Standby mode
This washing machine, in compliance with new energy
saving regulations, is fitted with an automatic standby
system which is enabled after a few minutes if no activity
is detected. Press the ON-OFF
button briefly and wait
for the machine to start up again.
PORTHOLE DOOR
PORTHOLE DOOR
HANDLE
ADJUSTABLE FEET
KICK STRIP
EN
5
WASH CYCLE
SELECTOR knob
Button withON/OFF
indicator light
Touch control panel
Button with ON/OFF indicator light: press this briefly to
switch the machine on or off. The green indicator light
indicates that the machine is switched on. To switch off the
washing machine during the wash cycle, press and hold the
button for approximately 3 seconds; if the button is
pressed briefly or accidentally the machine will not switch
off. If the machine is switched off during a wash cycle, this
wash cycle will be cancelled.
WASH CYCLE SELECTOR knob: may be turned in either
direction. To select the most suitable wash cycle, please refer
to the Table of wash cycles.
The knob will not move during the wash cycle.
M1-M2-M3 buttons: press and hold one of the buttons to
store a cycle with your own set preferences in the memory of
the machine. To recall a previously-stored cycle, press the
corresponding button.
TEMPERATURE
button: press to modify or exclude the
temperature setting; the value selected will appear on the
display above (see Running a wash cycle).
SPIN CYCLE
button: press to modify or exclude the spin
cycle; the value selected will appear on the display above (see
Running a wash cycle).
DELAYED START
button: press to set a delayed start
for the selected wash cycle; the set delay time will appear on
the display above (see Running a wash cycle).
OPTION buttons: press to select the available options. The
indicator light corresponding to the selected option will remain
lit (see Running a wash cycle).
WASH CYCLE PHASE icons: these illuminate to indicate the
progress of the wash cycle (Wash
 Rinse  Spin
Drain
). The text lights up when the cycle is complete.
START/PAUSE button with indicator light: when the green
indicator light flashes slowly, press the button to start a wash
cycle. Once the cycle has begun the indicator light will remain
lit in a fixed manner. To pause the wash cycle, press the button
again; the indicator light will flash in an orange colour. If the
Door locked
indicator light is switched off, the door may
be opened. To start the wash cycle from the point at which it
was interrupted, press the button again.
DOOR LOCKED
indicator light: indicates that the
porthole door is locked. To open the door, pause the wash
cycle (see Running a wash cycle).
CONTROL PANEL LOCK
button with indicator light: to
activate or deactivate the control panel lock, press and hold
the button for approximately 2 seconds. when the indicator
light is illuminated, the control panel is locked. This means it is
possible to prevent wash cycles from being modified
accidentally, especially where there are children in the home.
ECO indicator light: the icon lights up when, after altering
the washing parameters, an energy saving of at least 10% is
made. Furthermore, before the machine enters Standby
mode, the icon will light up for a few seconds; when the
machine is switched off the estimated energy saving will be
around the 80% mark.
CHANGE LANGUAGE
The first time the machine is switched on, the first
language will flash on the display. The "
", "OK" and "V"
symbols will appear on the display, in line with the 3 buttons
on the right-hand side. The languages change automatically
every 3"; alternatively, they can be changed by pressing the
buttons next to the " " and "V" symbols. Use the "OK" button
to confirm the language, which will be set after 2". If no
buttons are pressed, the automatic language change will
begin again after 30".
The language may only be changed while the machine is
switched off.
Press and hold the temperature
+spin +delayed start
buttons for 5''; a short beep sounds and the set language
flashes on the display. Press the buttons next to the "
" and
"V" symbols to change the language. Use the button next to
the "OK" symbol to confirm the language, which will be set
after 2". If no buttons are pressed, the language set previously
will be displayed after 30".
Switch on the machine.
TEMPERATURE
button
OPTION
buttons
SPIN
button
DISPLAY
M1
ECO
indicator light
DELAYED START
button
START/PAUSEbutton
with indicator light
DOOR LOCKED indicator light
WASH
CYCLE
PHASE
icons
CONTROL PANEL
LOCK button with
indicator light
M2
M3
EN
6
WARNING: before you use the washing machine for
the first time, run a wash cycle with detergent and no
laundry, using the 90° cottons cycle without pre-wash.
1. SWITCH THE MACHINE ON. Press the
button.
All the indicator lights will illuminate for 1 second and
the text AQUALTIS will appear on the display; the
indicator light corresponding to the
button will then
remain lit in a constant manner and the START/PAUSE
indicator light will flash.
2. SELECT THE PROGRAMME. Turn the
PROGRAMME KNOB left or right, until the required
programme has been selected; the name of the
programme will appear on the display. A temperature
and spin speed is set for each programme; these may
be adjusted. The cycle duration will also appear on
the display.
3. LOAD THE LAUNDRY. Open the porthole door.
Load the laundry, making sure you do not exceed the
maximum load value indicated in the table of wash
cycles on the following page.
4. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
Description of the machine.
5. CLOSE THE PORTHOLE DOOR.
6. CUSTOMISE THE WASH CYCLE. Use the
relevant buttons on the control panel:
Modify the temperature and/or spin speed.
The machine automatically displays the maximum
temperature and spin speed values set for the
selected cycle, or the most recently-used settings if
they are compatible with the selected cycle. The
temperature can be decreased by pressing the
button, until the cold wash OFF setting is reached.
The spin speed may be progressively reduced by
pressing the
button, until it is completely excluded
OFF. If these buttons are pressed again, the
maximum values are restored.
Exception: if the Cottonsprogramme is selected, the
temperature can be increased up to a value of 90°C.
Setting a delayed start.
To set a delayed start for the selected cycle, press
the corresponding button repeatedly until the required
delay period has been reached. During the setting
procedure, the delay period and the text "Starts in:"
will be displayed, along with the flashing
symbol.
After the delayed start has been set, the
symbol
will remain fixed on the display, which will also indicate
the duration of the selected cycle with the text "Ends
in:" and the cycle duration. Press the DELAYED
START button just once to display the delay time set
previously.
After the countdown has begun, the display will show
the text "Starts in:" and the delay period. Once the
set delay time has elapsed, the machine will begin its
cycle and the display will show "Ends in:" and the
time remaining until the end of the cycle.
To remove the delayed start option, press the button
until the display shows the text OFF; the
symbol
will disappear.
Modify the cycle settings.
Press the button to activate the option; the name
of the option will then appear on the display and
the corresponding indicator light will illuminate.
Press the button again to deactivate the option;
the name of the option will then appear on the
display followed by the text OFF, and the
corresponding indicator light will switch off.
If the selected option is not compatible with the
selected wash cycle, this incompatibility will be
signalled by the flashing of the indicator light and a
sound alert (3 beeps); the option will not be activated.
If the selected option is not compatible with another
option that has been selected previously, the indicator
light corresponding to the first option selected will flash
and only the second option will be activated; the
indicator light corresponding to the button will remain
lit in a constant manner.
The options may affect the recommended load value
and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light
remains lit in a fixed manner and the porthole door
locks (the
DOOR LOCKED indicator light
illuminates). The icons corresponding to the wash
cycle phases will light up during the cycle to indicate
which phase is currently in progress.
To change a wash cycle once it has already started,
pause the washing machine by pressing the START/
PAUSE button; then select the desired cycle and
press the START/PAUSE button again.
To open the door during a wash cycle, press the
START/PAUSE button; if the DOOR LOCKED
indicator light is switched off you may open the door.
Press the START/PAUSE button again to restart the
wash cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This is indicated
by the illuminated text END. The porthole door may be
opened immediately. If the START/PAUSE indicator light
is flashing, press the button to end the cycle. Open the
door, unload the laundry and switch off the machine.
If you wish to cancel a cycle which has already begun,
press and hold the
button until the cycle stops and
the machine switches off.
Bag for quilts, curtains and delicate garments
The Aqualtis washing machine makes it easier for you to
wash even the most valuable and delicate garments in
complete confidence thanks to the special bag which
protects the laundry (this is supplied with the machine).
We recommend that the bag is used every time you
wash quilts and padded items with an outer layer made
using synthetic material.
Running a wash cycle
EN
7
Wash options
Steam Hygiene
This option enhances washing performance by
generating steam during the wash cycle that eliminates
any bacteria from fibres while treating them at the same
time. Place the laundry in the drum, choose a
compatible programme and select option "
".
The steam generated during washing machine
operation may cause the porthole door to become hazy.
It cannot be used in conjunction with
, (90°C), ,
, , , , , , , , .
Easy Iron
By selecting this option, the wash and spin cycles will be
modified in order to reduce the formation of creases.
At the end of the cycle the washing machine
drum will rotate slowly; the Easy Iron and START/
PAUSE indicator lights will flash. To end the cycle press
the START/PAUSE button or the Easy Iron button.
For the Silk
wash cycle, the machine will end the
cycle while the laundry is soaking and the Easy
Iron indicator light will flash. To drain the water so that
the laundry may be removed, press the START/PAUSE
button or the Easy Iron button.
It cannot be used in conjunction with
, , , , , .
Time Saver
If you select this option, the wash cycle duration will be
reduced by 30%-50%, depending on the selected cycle,
thereby guaranteeing simultaneous water and energy
saving. Use this cycle for lightly soiled garments.
It cannot be used in conjunction with
, , , ,
, , , , , .
Extra rinse
By selecting this option, the efficiency of the rinse is
increased and optimal residual detergent removal is
guaranteed. It is particularly useful for skin which is
sensitive to detergents. We recommend this option is
used with a full load of washing, or when a large amount
of detergent is required.
It cannot be used in conjunction with
, , , .
(*) The duration of the wash cycles can be checked
on the display.
(*) Note: 10 minutes after the START, the machine will recalculate the time remaining until the end of the wash cycle on the basis of the load inside it; this
value will then be shown on the display.
Wash cycles and options
Table of wash cycles
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 60456: set wash cycle
with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle
with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle
with a temperature of 40°C.
Icon Description of the wash cycle
Max.
temp.
(°C)
Max.
speed
(rpm)
Detergent and additives
Max.
load
(kg)
Cycle
duration
Detergent
for prewash
Detergent
for wash
Fabric
softener
Cottons wash cycles
Cotton
with pre-wash
(Add detergent to the relevant compartment).
90° 1600
lll
9
Cotton (1): heavily soiled whites and resistant colours.
60°
(Max. 90°)
1600 -
ll
9
Cotton (2): heavily soiled whites and delicate colours.
40° 1600 -
ll
9
Coloured Cotton (3) 40° 1600 -
ll
9
Shirts
40° 600 -
ll
2
Jeans
40° 800 -
ll
4
Special programmes
Baby: heavily soiled delicate colours
40° 800 -
ll
4
Durable Synthetics 60° 800 -
ll
4
* Steam Refresh (see next page).
- - - - - 1,5
"Bed & Bath" for bedlinen and towels.
60° 1600 -
ll
9
Duvets: for down-stuffed garments.
30° 1200 -
ll
3,5
Silk: for garments in silk and viscose, lingerie.
30° 0 -
ll
2
Wool: for wool, cashmere, etc.
40° 600 -
ll
2
Mix 30':
to refresh lightly soiled garments quickly (not suitable
for wool, silk and clothes which require washing by hand)
30° 800 -
ll
3,5
Partials wash cycles
Rinse - 1600 - -
l
9
Spin - 1600 - - - 9
Drain - 0 - - - 9
EN
8
Detergents and laundry
Detergent
The type and quantity of detergent required depend on the
type of fabric you are washing (cotton, wool, silk, etc.), as well
as its colour, the washing temperature, the level of soiling and
the hardness of the water in the area. Measuring out the
detergent carefully will avoid wastage and help to protect the
environment: although they are biodegradable, detergents still
contain ingredients which alter the balance of nature.
We recommend the following:
use powder detergents for white cotton garments and
pre-washing.
use liquid detergents for delicate cotton garments and
for all low-temperature wash cycles.
use gentle liquid detergents for wool and silk garments.
The detergent should be poured into the relevant
compartment - or the dispenser placed directly inside
the drum - before the wash cycle begins. In the latter
case, it will not be possible to select the Cottons with
pre-wash cycle.
Do not use hand washing detergents because these
create too much foam.
Preparing the laundry
Shake out the garments before loading them into the
machine.
Divide the laundry according fabric type (symbol on the
washing instruction label) and colour, making sure you
separate the coloured garments from the white ones;
Empty all pockets and check the buttons;
Do not exceed the values listed in the Table of wash
cycles, which refer to the weight of the laundry when dry.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillowcase 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
1 pair of jeans 400-500 g
1 shirt 150-200 g
Washing recommendations
* Steam Refresh
This programme refreshes garments by removing bad
odours and relaxing the fibres (1.5 kg, roughly 3 items).
Insert dry items only (that are not dirty) and select
programme "
". The garments will be damp once the
cycle is completed, so we recommend hanging them to
dry. The "
" programme makes ironing easier.
Moreover, with the "Steam Perfume" laundry balls, your
favourite perfume can be added to your laundry. Place a
few drops of perfume on the sponge contained inside
the laundry ball, close it and insert it into the drum
together with the laundry. Then launch the specific
programme "
". At the end of the cycle, garments will
be relaxed and fragrant.
Not recommended for wool or silk garments.
Do not add too much perfume to the sponge in order
to avoid it dripping.
Do not add softeners or detergents.
Shirts: use the special Shirts
wash cycle to wash
shirts in different fabrics and colours to guarantee they
receive the best possible care.
Jeans: use the special Jeans
wash cycle for all
denim garments; turn inside out before washing and use
a liquid detergent.
Baby: use the special Baby
wash cycle to remove
the remove the soiling typically caused by babies, while
removing all traces of detergent from nappies in order to
prevent the delicate skin of babies from suffering allergic
reactions. The cycle has been designed to reduce the
amount of bacteria by using a greater quantity of water
and optimising the effect of special disinfecting additives
added to the detergent. At the end of the wash cycle,
the machine will slowly rotate the drum; to end the cycle
press the START/PAUSE button.
Silk: use the special Silk
wash cycle to wash all silk
garments. We recommend the use of special detergent
which has been designed to wash delicate clothes.
Curtains: use the Silk
wash cycle. These should
be folded and placed inside the bag provided.
Wool: Ariston is the only washing machine brand to
have been awarded the prestigious Woolmark Platinum
Care endorsement (M.0508) by the Woolmark Company,
which means that all woollen garments may be washed
in the washing machine, even those which state hand
wash only
on the label. The Wool wash cycle can
be used to wash all woollen garments in the washing
machine while guaranteeing optimum performance.
Duvets: to wash double or single duvets (the weight of
which should not exceed 3,5 kg), cushions or clothes
padded with goose down such as puffa jackets, use the
special Duvets
wash cycle. We recommend that
duvets are placed in the drum with their edges folded
inwards (see figure) and that no more than ¾ of the total
volume of the drum is used. To achieve the best results,
we recommend that a liquid detergent is used and
placed inside the detergent dispenser drawer.
Quilts: to wash quilts with a synthetic outer layer, use
the bag provided and set the wash cycle to Duvets
.
Bedlinen and towels: use the Bed & Bath
cycle
to wash laundry from all over the house; this optimises
fabric softener performance and helps you save time and
energy. We recommend the use of powder detergent.
Stubborn stains: it is wise to treat stubborn stains with
solid soap before washing, and to use the Cottons with
pre-wash cycle.
EN
9
Precautions and tips
The machine was designed and constructed in
accordance with international safety regulations. The
following information is provided for safety reasons and
must therefore be read carefully.
General safety
This appliance was designed for domestic use only.
the machine must only be used by adults, in
accordance with the instructions given in this manual.
Do not touch the machine when barefoot or with wet
or damp hands or feet.
Do not pull on the power supply cable when
unplugging the appliance from the electricity socket.
Hold the plug and pull.
Do not touch the drained water as it may reach
extremely high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent
accidental opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance
while it is operating.
If it must be moved, proceed with the help of two or
three people and handle it with the utmost care.
Never try to do this alone, because the appliance is
very heavy.
Before loading laundry into the washing machine,
make sure the drum is empty.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
before every spin and to distribute the load in a uniform
manner, the drum rotates continuously at a speed which
is slightly greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly, the
machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs
the distribution process instead of spinning. To encourage
improved load distribution and balance, we recommend
small and large garments are mixed in the load.
Disposal
Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states
that household appliances should not be disposed of
using the normal solid urban waste cycle. Exhausted
appliances should be collected separately in order to
optimise the cost of re-using and recycling the
materials inside the machine, while preventing
potential damage to the atmosphere and to public
health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations
regarding separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their
local authorities or appliance dealer.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the
electrical socket.
2. make sure the water level
inside the machine is lower
than the door opening; if it is
not, remove excess water
using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. remove the cover panel on the lower front part of the
washing machine (see overleaf).
4. pull outwards using the
tab as indicated in the figure,
until the plastic tie-rod is
freed from its stop position;
pull downwards until you
hear a click, which
indicates that the door is
now unlocked.
5. open the door; if this is
still not possible repeat the
procedure.
6. reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
EN
10
Care and maintenance
1
2
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This will
limit wear on the hydraulic system in the machine and
help to prevent leaks.
Unplug the appliance when cleaning it and during all
maintenance work.
Cleaning the machine
The outer parts and rubber components of the appliance
can be cleaned using a soft cloth soaked in lukewarm
soapy water. Do not use solvents or abrasives.
Cleaning the detergent dispenser
drawer
To remove the drawer, press
lever (1) and pull the drawer
outwards (2) (see figure).
Wash it under running
water; this procedure should
be repeated frequently.
Caring for your appliance drum
Always leave the door ajar to prevent unpleasant
odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
protective pre-chamber at the base of the pump.
Make sure the wash cycle has finished and unplug the
appliance.
To access the pre-chamber:
1. take off the cover panel on the front of the machine
by first pressing it in the centre and then pushing
downwards on both sides until you can remove it (see
figures);
2. position a container so
that it will collect the water
which flows out
(approximately 1.5 l) (see
figure);
3. unscrew the lid by
rotating it in an anti-
clockwise direction (see
figure);
4. clean the inside thoroughly;
5. screw the lid back on;
6. reposition the panel, making sure the hooks are
securely in place before you push it onto the appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
1
2
EN
11
Trouble shooting
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Centre
(see Assistance), make sure that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not fill
with water.
The washing machine door
remains locked.
The machine continuously fills
with water and drains.
The washing machine does not
drain or spin.
The machine vibrates a lot during
the spin cycle.
The washing machine leaks.
The icons corresponding to the
Phase in progress flash rapidly
at the same time as the ON/OFF
indicator light.
There is too much foam.
The washing machine door
remains locked.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or not enough to make
contact.
There is no power in the house.
The door is not closed properly.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
If you have selected the Baby
cycle or the Easy iron option, when
the wash cycle has finished the machine will slowly rotate the drum; to end
the cycle press the START/PAUSE button or the Easy iron
button. If
you have selected the Silk
wash cycle, the machine will end the cycle
while the laundry is soaking; to drain the water so that the laundry may be
removed, press the START/PAUSE button or the Easy iron
button.
The drain hose is not fitted at a height between 65 and 100 cm from the
floor (see Installation).
The free end of the hose is under water (see Installation).
If the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washing machine to fill
with water and drain continuously. Special anti-draining valves are available
in shops and help to prevent this inconvenience.
The wall drainage system is not fitted with a breather pipe.
The wash cycle does not include draining: Some wash cycles require the
drain phase to be started manually (see Wash cycles and options).
The Easy iron option is enabled: to complete the wash cycle, press the
START/PAUSE button (Wash cycles and options).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The machine is not level (see Installation ).
The machine is trapped between cabinets and walls (see Installation).
The load is unbalanced (see Detergents and laundry).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser is blocked (to clean it, see Care and
maintenance).
The drain hose is not fixed in place properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute and
then switch it back on again. If the problem persists, contact the Technical
Assistance Service.
The detergent is not suitable for machine washing (it should display the text
for washing machines or hand and machine wash, or the like).
Too much detergent was used.
Perform the manual unlocking procedure (see Precautions and tips).
Note: To exit Demo mode, press and hold the two ON/OFF and START/PAUSE buttons simultaneously for 3 seconds.
EN
12
Before calling for Assistance:
Check whether you can solve the problem by yourself (see Trouble shooting);
Restart the wash cycle to check whether the problem has been solved;
If it has not, contact the Authorised Technical Assistance Service.
If the washing machine has been installed or used incorrectly, you will have to pay for the call-out service.
Always request the assistance of authorised technicians.
Please have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
The above information can be found on the data plate located on the appliance itself.
Assistance
13
FR
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Caractéristiques techniques
Description de lappareil, 16-17
Tableau de bord "touch control"
Comment faire un cycle de lavage, 18
Programmes et options, 19
Tableau des programmes
Options de lavage
Produits lessiviels et linge, 20
Lessive
Triage du linge
Conseils de lavage
Précautions et conseils, 21
Sécurité générale
Système déquilibrage de la charge
Mise au rebut
Ouverture manuelle de la porte hublot
Entretien et soin, 22
Coupure de larrivée deau et du courant
Nettoyage de lappareil
Nettoyage du tiroir à produits lessiviels
Entretien du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Anomalies et remèdes, 23
Assistance, 24
FR
LAVE-LINGE
AQUALTIS
AQ9D 69 U
Mode dinstallation et demploi
FR
14
Installation
Conserver ce mode demploi pour pouvoir le consulter
à tout moment. En cas de vente, de cession ou de
déménagement, veiller à ce quil accompagne toujours
le lave-linge.
Lire attentivement les instructions : elles fournissent
des conseils importants sur linstallation, lutilisation et la
sécurité de lappareil.
Cette notice, la garantie et les pièces servant à
linstallation sont réunies dans un sachet.
Déballage et mise à niveau
Déballage
1. Sitôt le lave-linge déballé, sassurer quil na pas été
endommagé pendant son transport.
Sil est abîmé, ne pas le raccorder et contacter le
vendeur.
2. Enlever les quatre vis de
protection pour le
transport, le caoutchouc
et la cale, placés dans la
partie arrière (voir figure).
3. Boucher les trous à laide des bouchons plastique
fournis dans le sachet.
4. Ces pièces sont à conserver car il faut les remonter
en cas de déplacement du lave-linge pour éviter
dendommager lintérieur de lappareil pendant le
transport.
Les pièces demballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Poser le lave-linge sur un sol plat et rigide, sans
ladosser à un mur ou à un meuble.
2. Pour compenser les
irrégularités du sol, visser
ou dévisser les pieds de
réglage jusquà ce que
lappareil soit parfaitement
à lhorizontale (il ne doit
pas être incliné de plus de
2 degrés).
Une mise à niveau minutieuse garantit une bonne
stabilité de lappareil et évite toute vibration et bruit
surtout pendant lessorage.
Si lappareil est posé sur de la moquette ou un tapis,
agir sur les pieds de réglage de manière à ce quil y ait
suffisamment de place pour assurer une bonne
ventilation.
Raccordements eau et électricité
Raccordement du tuyau darrivée de leau
Avant de raccorder le tuyau darrivée de leau, laisser
couler leau jusquà ce quelle soit limpide.
1. Raccorder le tuyau
darrivée de leau à
lappareil en le vissant à la
prise deau prévue, dans la
partie arrière en haut à
droite (voir figure).
2. Reliez le tuyau
dalimentation en le vissant
à un robinet deau froide à
embout fileté 3/4 gaz (voir
figure).
3. Attention à ce que le tuyau ne soit pas plié ou écrasé.
La pression de leau doit être comprise entre les
valeurs indiquées dans le tableau des Caractéristiques
techniques (voir page ci-contre).
Si la longueur du tuyau dalimentation ne suffit pas,
sadresser à un magasin spécialisé ou à un technicien
agréé.
Ne jamais utiliser de tuyaux darrivée usés mais
uniquement ceux fournis avec lappareil.
15
FR
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau de
vidange à un conduit
dévacuation ou à une
évacuation murale placés
à une distance du sol
comprise entre 65 et 100
cm en évitant à tout prix
de le plier.
Autrement, accrocher le
tuyau de vidange à un
évier ou à une baignoire,
dans ce cas, fixer le
support plastique fourni
avec lappareil au robinet
(voir figure).
Lextrémité libre du tuyau
dévacuation ne doit pas
être plongée dans leau.
Lutilisation dun tuyau de rallonge est absolument
déconseillée mais si on ne peut faire autrement, il faut
absolument quil ait le même diamètre que le tuyau
original et sa longueur ne doit pas dépasser 150 cm.
Raccordement électrique
Avant de brancher la fiche dans la prise de courant,
sassurer que :
la prise est bien reliée à la terre et est conforme aux
réglementations en vigueur;
la prise est bien apte à supporter la puissance
maximale de lappareil indiquée dans le tableau des
Caractéristiques techniques (voir ci-contre);
la tension dalimentation est bien comprise entre les
valeurs figurant dans le tableau des Caractéristiques
techniques (voir ci-contre);
la prise est bien compatible avec la fiche de lappareil.
Autrement, remplacer la prise ou la fiche.
Cet appareil ne doit pas être installé à lextérieur,
même à labri, car il est très dangereux de le laisser
exposé à la pluie et aux orages.
Après installation de lappareil, la prise de courant doit
être facilement accessible.
Nutiliser ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni trop écrasé.
Le câble dalimentation et la fiche ne doivent être
remplacés que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas de
non-respect des normes énumérées ci-dessus.
Caractéristiques techniques
Modèle
AQ9D 69 U
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 64,5 cm
Capaci
de 1 à 9 kg
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 62 litres
Vitesse
d'essorage
jusqu'à 1600 tours minute
Programmes de
contrôle selon la
norme EN 60456
programme ; temrature 60°C;
effectavec une charge de 9 kg.
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibilité électromagnétique) et
modifications suivantes
- 2006/95/CE (Basse Tension)
- 2002/96/CE
FR
16
1
2
Description de lappareil
PORTE HUBLOT
Pour ouvrir la porte, se
servir de la poignée prévue
(voir illustration).
TIROIR A PRODUITS LESSIVIELS
Le tiroir est situé à lintérieur
de lappareil et il faut ouvrir
la porte pour y accéder.
Pour le dosage des produits
lessiviels, consulter le
chapitre Produits lessiviels
et linge.
Remarque : coller sur le
tiroir létiquette contenant les
descriptions des
programmes et options.
Létiquette se trouve dans la pochette avec le présent
manuel.
1. bac à produit de
prélavage : utiliser de la
lessive en poudre.
2. bac à produit de lavage :
utiliser de la lessive en poudre
ou liquide. Dans ce dernier
cas, il est recommandé de le
verser juste avant de
démarrer le lavage.
bac à additifs : pour
assouplissant ou additifs
liquides. Il est recommandé de ne jamais dépasser le
niveau maximal indiqué par la grille et de diluer des
assouplissants concentrés.
Tableau de bord "touch control"
Pour modifier les sélections,
appuyer légèrement sur
l'icône à l'intérieur de la
zone sensible (touch control)
comme illustré (voir figure).
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l'économie d'énergie, est
équipée d'un système d'extinction automatique (veille)
activé après quelques minutes d'inutilisation. Appuyez
brièvement sur la touche ON-OFF
et attendre que la
machine soit réactivée.
TABLEAU DE
BORD
PORTE
HUBLOT
POIGNEE
PORTE
HUBLOT
SOCLE
PIEDS REGLABLES
17
FR
Bouton avec témoin ON/OFF: appuyer brièvement sur la
touche pour allumer ou éteindre lappareil. Le témoin vert
indique que lappareil est sous tension. Pour éteindre le lave-
linge en cours de lavage, appuyer sur la touche pendant au
moins 3 secondes de suite; une pression brève ou
accidentelle nentraîne pas larrêt de lappareil. Larrêt de
lappareil pendant un lavage annule le lavage en cours.
Bouton PROGRAMMES: il peut tourner dans les deux sens.
Pour sélectionner le programme plus adapté, consulter le
Tableau des programmes.
Pendant le lavage, le bouton reste fixe.
Touches M1-M2-M3: exercer une pression sur une des
touches pour mémoriser un cycle et les personnalisations
préférées. Pour retourner à un cycle précédemment mémorisé
appuyer sur la touche correspondante.
Touche
TEMPERATURE: appuyer sur la touche pour
régler ou supprimer la température; la valeur est indiquée par
les voyants situés au-dessus (voir Comment faire un cycle de
lavage).
Touche ESSORAGE: appuyer sur la touche pour régler ou
supprimer lessorage; la valeur est indiquée par les voyants
situés au-dessus (voir Comment faire un cycle de lavage).
Touche
DEPART DIFFÉRÉ: appuyer sur la touche pour
sélectionner un départ différé du programme choisi; le retard
programmé est indiqué par lécran situé au-dessus (voir
Comment faire un cycle de lavage).
Touches et Voyants OPTIONS: appuyez pour sélectionner les
options disponibles. Le voyant correspondant à loption
sélectionnée reste allumé (voir Comment faire un cycle de lavage).
Icônes PHASES DE LAVAGE: elles sallument pour indiquer
le stade davancement du cycle (Lavage
- Rinçage -
Essorage
Vidange finale ).
Linscription
sallume quand le cycle est terminé.
Touche avec voyant START/PAUSE: quand le voyant vert
clignote lentement, appuyer sur la touche pour démarrer un
lavage. Une fois le cycle lancé, le voyant passe à lallumage
fixe. Pour activer une pause de lavage, appuyer à nouveau sur
la touche; le voyant passe à lorange et se met à clignoter. Si
Bouton avec témoin
ON/OFF
le voyant Porte verrouillée est éteint, on peut ouvrir la
porte. Pour faire redémarrer le lavage exactement à lendroit
de larrêt, appuyer une nouvelle fois sur la touche.
Voyant
HUBLOT VERROUILLEÉ: il indique que la porte
hublot est verrouillée. Pour pouvoir ouvrir la porte, il faut
mettre le cycle en pause (voir Comment faire un cycle de
lavage).
Bouton avec témoin VERROU ENFANT: pour activer ou
désactiver le verrouillage des commandes, garder la touche
enfoncée pendant environ 2 secondes. Lallumage du voyant
signale que le tableau est verrouillé. Ceci permet déviter toute
modification involontaire des programmes, surtout sil y a des
enfants à la maison.
Voyant ECO: licône
sallume quand la modification des
paramètres de lavage permet datteindre au moins 10%
déconomie délectricité.
De plus, avant que l'appareil ne se mette en mode "Stand by",
l'icône s'allume pendant quelques secondes. Appareil éteint, la
récupération d'énergie estimée est d'environ 80%.
MODIFICATION DE LA LANGUE
A la première mise en service de lappareil, la première
langue clignote à lécran. En correspondance des 3 touches à
droite de lécran, il y a affichage des symboles
, OKet
V. Les langues changent automatiquement toutes les 3
secondes ou par pression des touches à côté des symboles
et V. La touche OKpermet de confirmer la langue qui
devient fixe au bout de 2 secondes. Si aucune pression nest
exercée, le changement de langue automatique reprend au
bout de 30 secondes.
La langue ne peut être modifiée quappareil éteint.
Un pression simultanée de 5 secondes sur les touches
température
+ essorage + départ différé déclenche
un bref signal sonore et affiche à lécran la langue sélectionnée
clignotante. Pour changer de langue, appuyer sur les touches
à côté des symboles
et V. La touche à côté du symbole
OKpermet de confirmer la langue qui devient fixe au bout de
2 secondes. Si aucune pression nest exercée, le changement
de langue automatique reprend au bout de 30 secondes.
Allumer lappareil.
Tableau de bord "touch control"
Écran
M1
Bouton
PROGRAMMES
M2
Touches
OPTIONS
Touche TEMPÉRATURE
Touche ESSORAGE
Touche avec voyant
START/PAUSE
Voyant
ECO
Voyant HUBLOT
VERROUILLEÉ
Icônes PHASES
DE LAVAGE
Bouton avec témoin
VERROU ENFANT
Touche DEPART
DIFFÉRÉ
M3
FR
18
REMARQUE: lors de la première mise en service du
lave-linge, lancer un cycle de lavage à vide mais avec du
produit lessiviel en sélectionnant un programme coton
90° sans prélavage.
1. METTRE L'APPAREIL SOUS TENSION. Appuyer
sur la touche
. Tous les voyants s'allument pendant
1 seconde et AQUALTIS est affiché à l'écran; le
voyant de la touche
reste allumé et le voyant
START/PAUSE se met à clignoter.
2. CHOISIR LE PROGRAMME. Tourner le BOUTON
PROGRAMMES vers la droite ou vers la gauche pour
sélectionner le programme désiré. Le nom du programme
est affiché à l'écran avec attribution d'une température et
d'une vitesse d'essorage qui peuvent être modifiées.
L'écran affiche la durée du cycle de lavage.
3. CHARGER LE LINGE. Ouvrir la porte hublot.
Charger le linge en faisant attention à ne pas
dépasser la quantité indiquée dans le tableau des
programmes de la page suivante.
4. DOSER LE PRODUIT LESSIVIEL. Sortir le tiroir et
placer le produit lessiviel dans les bacs correspondants
comme indiqué au paragraphe Description de lappareil.
5. FERMER LA PORTE HUBLOT.
6. PERSONNALISER LE CYCLE DE LAVAGE. Agir
sur les touches correspondantes du tableau de bord:
Modifier la température et/ou la vitesse
dessorage.
L'appareil affiche automatiquement la température et
l'essorage maximum prévus pour le programme
sélectionné ou ceux qui ont été sélectionnés en
dernier s'ils sont compatibles avec le programme
choisi. En appuyant sur la touche
, on peut
diminuer progressivement la température de lavage
jusquà un lavage à froid (OFF). En appuyant sur la
touche
, on peut diminuer progressivement la
vitesse dessorage jusquà sa suppression totale
(OFF). Une autre pression sur les touches ramènera
les valeurs aux maximums prévus.
Exception: lors de la sélection du programme Coton
Blanc la température peut être augmentée jusquà 90°.
Sélectionner un départ différé.
Pour programmer le départ différé dun programme
sélectionné, appuyer sur la touche correspondante
jusquà ce que le retard désiré soit atteint. Pendant le
réglage, le temps de décalage est affiché ainsi que le
message Démarrage dans:et le symbole
clignotant. Après avoir programmé le départ différé,
lécran affiche le symbole
en fixe et lécran
retourne à laffichage de la durée du cycle
sélectionné, du message Finit dans:et de la durée
du cycle. Une seule pression sur la touche DÉPART
DIFFÉRÉ permet dafficher le délai dattente
sélectionné précédemment.
Après le lancement, lécran affiche le message
Démarrage dans:et le temps de décalage.
Une fois que le délai dattente sélectionné touche à
sa fin, lappareil démarre et lécran affiche le message
Finit dans:et le temps restant jusquà la fin du
cycle. Pour annuler le départ différé, appuyer sur la
touche jusqu'à ce que l'écran affiche OFF; le symbole
s'éteindra.
Modifier les caractéristiques du cycle.
Appuyer sur la touche pour activer l'option,
l'écran affiche le nom de l'option et le croissant
de lune correspondant à la touche s'allume.
Appuyer une nouvelle fois sur la touche pour
désactiver l'option, l'écran affiche le nom de
l'option plus OFF et le croissant de lune s'éteint.
Si la fonction sélectionnée est incompatible avec le
programme sélectionné, le voyant correspondant se
met à clignoter, un signal sonore (3 bips) retentit et la
fonction nest pas activée.
Si loption sélectionnée est incompatible avec une
autre option précédemment sélectionnée, le voyant
correspondant à la première option se met à clignoter
et seule la deuxième option est activée le voyant de la
touche reste fixe.
Les options permettent de modifier la charge
conseillée et/ou la durée du cycle de lavage.
7. DEMARRER LE PROGRAMME. Appuyer sur la
touche START/PAUSE. Le voyant correspondant
reste fixe et la porte hublot est verrouillée (voyant
HUBLOT VERROUILLEÉ
allumé). Les icônes
correspondant aux phases de lavage sallument
pendant le cycle pour indiquer la phase en cours.
Pour changer un programme tandis quun cycle est
en cours, activer une pause du lave-linge par pression
sur la touche START/PAUSE; sélectionner enfin le
cycle désiré et appuyer à nouveau sur la touche
START/PAUSE. Pour ouvrir la porte tandis quun cycle
est en cours, appuyer sur la touche START/PAUSE; si
le voyant HUBLOT VERROUILLEÉ
est éteint, on
peut ouvrir la porte. Pour faire redémarrer le
programme exactement à lendroit de larrêt, appuyer
une nouvelle fois sur la touche START/PAUSE.
8. FIN DU PROGRAMME. Elle est signalée par
linscription END allumée. La porte hublot peut alors
être ouverte aussitôt. Si le voyant START/PAUSE
clignote, appuyer sur la touche pour terminer le cycle.
Ouvrir la porte, vider le lave-linge et éteindre lappareil.
Une pression prolongée sur la touche
permet
dannuler un cycle déjà lancé. Le cycle est interrompu et
la machine séteint.
Sachet pour édredons, rideaux et vêtements délicats
Grâce au sachet spécial fourni avec lappareil, le lave-
linge Aqualtis vous permet de laver à la machine même
vos vêtements plus délicats et précieux en assurant au
maximum leur protection. Nous recommandons en tout
cas dutiliser le sachet pour le lavage dédredons et de
couettes avec housse réalisée dans un matériau
synthétique.
Comment faire un cycle de
lavage
19
FR
Icône Description du Programme
Te m p.
maxi
C)
Vitesse
maxI
(tours
minute)
Produits lessiviels
Charge
maxi
(Kg)
Durée
cycle
Pré-
lavage
Lavage Adoucissant
Programmes Coton
COTON
avec
PRÉLAVAGE:
pour enlever les taches tenaces.
(Ajouter le produit lessiviel dans le bac prévu).
90° 1600
ll l
9
COTON
BLANC
(1):
Blancs et couleurs résistantes très sales.
60°
(Maxi 90°)
1600 -
ll
9
COTON
BLANC
(2):
Blancs et couleurs délicates très sales.
40° 1600 -
ll
9
COTON
COULEURS
(3)
40° 1600 -
ll
9
CHEMISES
40° 600 -
ll
2
JEANS
40° 800 -
ll
4
Programmes spécial
BÉBÉ:
couleurs délicates très sales.
40° 800 -
ll
4
SYNTHETIQUE
RÉSISTANT
60° 800 -
ll
4
* FRAÎCHEUR VAPEUR
(voir page ci-contre).
- - - - - 1,5
LIT ET BAIN:
pour le linge de lit et le linge de toilette.
60° 1600 -
ll
9
DUVET:
pour linge et vêtements en duvet d'oie.
30° 1200 -
ll
3,5
SOIE:
pour linge en soie, viscose, lingerie.
30° 0 -
ll
2
LAINE:
pour laine, cachemire, etc.
40° 600 -
ll
2
MIX 30':
pour rafrchir rapidement du linge peu sale (ne
convient pas pour la laine, la soie et le linge à laver à la main).
30° 800 -
ll
3,5
Fonction (Programmes partiaux)
Riage - 1600 - -
l
9
Essorage - 1600 - - - 9
Vidange - 0 - - - 9
Options de lavage
Vapeur Hygiène
La sélection de cette option augmente l'efficacité du
lavage par la production de vapeur qui pendant le cycle
de lavage élimine aussi les bactéries nichées dans les
fibres tout en prenant soin du linge. Introduire le linge
dans le tambour, sélectionner le programme compatible
et choisir l'option "
".
Pendant le fonctionnement du lave-linge, il se peut que
la porte hublot soit moins transparente à cause de la
formation de vapeur.
Cette option ne peut être activée avec les programmes
, (90°C), , , , , , , , , , .
Repassage Facile
En cas de sélection de cette option, le lavage et lessorage
seront dûment modifiés pour réduire la formation de plis. A
la fin du cycle de lavage, le lave-linge fait tourner le
tambour lentement; les voyants Repassage Facile et
START/PAUSE se mettent à clignoter. Pour finir le cycle,
appuyer sur la touche START/PAUSE ou sur la touche
Repassage Facile. Pour le programme Soie
lappareil
arrive au bout du cycle en laissant le linge tremper, le
voyant Repassage facile clignote. Pour vidanger leau et
pouvoir sortir le linge, il faut appuyer sur la touche START/
PAUSE ou sur la touche Repassage Facile.
Cette option nest pas disponible avec les programmes
, , , , , .
Temps Réduit
En sélectionnant cette option, la durée du programme
est réduite de 30 à 50 % en fonction du cycle choisi, ce
qui permet de faire des économies deau et dénergie.
Utiliser ce programme pour les vêtements modérément
sales.
Cette option nest pas disponible avec les programmes
, , , , , , , , , .
Rinçage Plus
La sélection de cette option permet daugmenter
lefficacité du rinçage et déliminer totalement toute
trace de lessive. Elle est très utile pour les personnes
particulièrement sensibles aux produits lessiviels. Son
utilisation est conseillée en cas de pleine charge ou de
doses élevées de produit lessiviel.
Elle nest pas disponible pour les programmes
, ,
, .
(*) La durée des programmes de lavage est indiquée sur
lafficheur.
(*) Remarque : environ 10 minutes après le début du programme, selon la charge, la machine effectuera un nouveau calcul et affichera le temps restant jusquà la fin du programme.
Programmes et options
Tableau des programmes
Pour tous les instituts qui effectuent ces tests :
1) Programme de contrôle selon la norme EN 60456: sélectionner le programme
et une température de 60°C.
2) Programme coton long: sélectionner le programme
et une température de 40°C.
3) Programme coton court: sélectionner le programme
et une température de 40°C.
FR
20
Produits lessiviels et linge
Lessive
Le choix et la quantité de lessive dépendent du type de
textile (coton, laine, soie...), de la couleur, de la
température de lavage, du degré de salissure et de la
dureté de leau. Bien doser la quantité de produit lessiviel
permet déviter les gaspillages et protège lenvironnement :
bien que biodégradables, les produits lessiviels contiennent
des éléments qui altèrent léquilibre de la nature.
Il est conseillé de:
utiliser des lessives en poudre pour le linge en coton
blanc et pour le prélavage.
utiliser des lessives liquides pour linge délicat en coton
et pour tous les programmes basse température.
utiliser des lessives liquides délicates pour la laine et la soie.
Le produit lessiviel doit être versé juste avant le démarrage
du lavage dans le bac prévu à cet effet ou dans la boule
doseuse directement dans le tambour. Dans ce cas, le
cycle Coton avec prélavage nest pas disponible.
Ne pas utiliser de lessives pour lavage à la main, elles
génèrent trop de mousse.
Triage du linge
Bien déployer le linge avant de le charger.
Trier le linge selon le type de textile (symbole sur
létiquette du vêtement) et la couleur en veillant à bien
séparer le linge couleur du linge blanc;
Vider les poches et contrôler les boutons ;
Ne pas dépasser les valeurs indiquées dans le Tableau
des programmes correspondant au poids de linge sec.
Combien pèse le linge ?
1 drap 400-500 g
1 taie doreiller 150-200 g
1 nappe 400-500 g
1 peignoir 900-1200 g
1 serviette de toilette 150-250 g
1 jeans 400-500 g
1 chemise 150-200 g
Conseils de lavage
* Fraîcheur Vapeur
Ce programme permet de rafraîchir les vêtements,
d'éliminer les odeurs désagréables et de détendre les
fibres (1,5 kg, environ 3 vêtements). N'introduire que des
vêtements secs (non sales) et choisir le programme
"
". A la fin du cycle, les vêtements seront humides et
nous conseillons de les accrocher à un cintre.
Le programme "
" simplifie l'opération de repassage.
Les boules "Steam Parfum" permettent en outre
d'ajouter son parfum préféré pour embaumer le linge.
Mettre quelques gouttes de parfum sur l'éponge à
l'intérieur de la boule, la refermer et la glisser dans le
tambour avec les vêtements et faire démarrer le
programme délicat "
". A la fin du cycle les vêtements
seront souples et parfumés.
Déconseillé pour les textiles délicats comme la laine et
la soie.
Ne pas imprégner excessivement l'éponge de parfum
pour éviter qu'il ne coule.
Ne pas ajouter d'assouplissant ou de produit lessiviel.
Chemises: sélectionner le programme approprié au
lavage de chemises
pour laver des chemises de
textile et couleur différents.
Jeans: utiliser le programme Jeans
pour tous les
vêtements à base de textile Denim; mettre les vêtements
sur lenvers avant le lavage et utiliser une lessive liquide.
Bébé: utiliser le programme Bébé
pour enlever les
tâches des vêtements de bébé et rincer correctement
les vêtements afin déviter les réactions allergiques.
Spécialement conçu pour diminuer la charge
bactérienne, ce cycle utilise une plus grande quantité
deau et optimise leffet des additifs désinfectants
spécifiques ajoutés à la lessive. En fin de lavage,
lappareil fait tourner le tambour lentement. Pour
compléter le cycle appuyer sur la touche START/PAUSE.
Soie: sélectionner le programme Soie
pour le
lavage des vêtements en soie. Il est conseillé dutiliser
une lessive spéciale pour linge délicat.
Rideaux: Utiliser le programme Soie
. Nous
recommandons de les plier et de les mettre dans le
sachet fourni avec la machine.
Laine: Ariston est le seul lave-linge à avoir obtenu le
prestigieux label Woolmark Platinum Care (M.0508) délivré
par The Woolmark Company qui garantit le lavage à la
machine de tous les vêtements en laine, y compris ceux
qui portent létiquette lavage à la main uniquement
.
Grâce au programme Laine, on peut donc laver à la
machine, en toute tranquillité, tous les vêtements en laine
avec des performances de lavage garanties.
Duvets: pour laver des articles avec garnissage en duvet
doie comme par exemple des couettes pour une ou deux
personnes (poids maximal à ne pas dépasser 3,5 kg), oreillers,
anoraks, utiliser le programme spécial Duvets
. Pour
introduire les duvets dans le tambour, nous recommandons
de replier les bords vers lintérieur (voir figures) et de ne pas
occuper plus de ¾ du volume du tambour. Pour un lavage
optimal, nous recommandons dutiliser une lessive liquide à
doser dans le tiroir à produits lessiviels.
Edredons: pour laver les édredons avec housse
synthétique, utilisez le sachet spécial fourni avec la
machine et sélectionnez le programme «Duvets»
.
Linge de toilette et de lit: ce lave-linge permet de laver
tout le linge de maison de la semaine en un seul cycle Lit
et bain
qui optimise lutilisation de lassouplissant et
permet de faire des économies de temps et délectricité.
Nous conseillons dutiliser de la lessive en poudre.
Taches tenaces: mieux vaut traiter les taches tenaces
avec du savon solide avant le lavage et sélectionner ensuite
le programme Coton avec prélavage.
1 / 1

Indesit AQ9D 69 U (EX)/V Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues