Scholtes FRI 886.1 MT Mode d'emploi

Marque: Scholtes

Modèle: FRI 886.1 MT

Catégorie: Fours

Taper: Mode d'emploi

FRI 886.1 MT

English

Operating Instructions

OVEN

Français

Mode d’emploi

FOUR

Contents

Operating Instructions,1

Warnings,2

Assistance,4

Description of the appliance,5

Description of the appliance,6

Installation,7

Start-up and use,9

Modes,10

Precautions and tips,14

Maintenance and care,14

Troubleshooting,16

Sommaire

Mode d’emploi,1

Avertissements,3

Assistance,4

Description de l’appareil,5

Description de l’appareil,6

Installation,17

Mise en marche et utilisation,19

Programmes,20

Précautions et conseils,24

Nettoyage et entretien,24

Anomalies et remèdes,26

Warnings

WARNING: The appliance and its

accessible parts become hot during use.

Care should be taken to avoid touching

heating elements. Children less than 8

years of age shall be kept away unless

continuously supervised. This appliance

can be used by children aged from 8 years

and above and persons with reduced

physical, sensory or mental capabilities

or lack of experience and knowledge

if they have been given supervision

or instruction concerning use of the

appliance in a safe way and understand

the hazards involved. Children shall not

play with the appliance. Cleaning and

user maintenance shall not be made by

children without supervision.

Do not use harsh abrasive cleaners or

sharp metal scrapers to clean the oven door

glass since they can scratch the surface,

which may result in shattering of the glass.

“Before initiating the automatic cleaning

cycle:

• clean the oven door;

• remove large or coarse food residues

from the inside of the oven using a

damp sponge. Do not use detergents;

• remove all accessories and the sliding

rack kit (where present);

• do not place tea towels”

Keep children away from the appliance

during the automatic cleaning cycle as

surfaces may become very hot.

Never use steam cleaners or pressure

cleaners on the appliance.

WARNING: Ensure that the appliance is

switched off before replacing the lamp to

avoid the possibility of electric shock.

! When you place the rack inside, make

sure that the stop is directed upwards and

in the back of the cavity.

Avertissements

ATTENTION : Cet appareil ainsi que

ses parties accessibles deviennent très

chauds pendant leur fonctionnement.

Il faut faire attention à ne pas toucher

les éléments chauffants. Ne pas faire

approcher les enfants de moins de 8 ans

à moins qu’ils ne soient sous surveillance

constante. Le présent appareil peut

être utilisé par des enfants de plus de

8 ans et par des personnes présentant

des capacités physiques, sensorielles

ou mentales réduites ou n’ayant pas

l’expérience ou les connaissances

indispensables, à condition qu’ils soient

sous bonne surveillance ou qu’ils aient

reçu les instructions nécessaires pour une

utilisation de l’appareil en toute sécurité

et à condition qu’ils se rendent compte

des dangers encourus. Les enfants ne

doivent pas jouer avec l’appareil. Les

opérations de nettoyage et d’entretien

ne doivent pas être effectuées par des

enfants non surveillés.

Ne pas utiliser de produits abrasifs ni

de spatules métalliques coupantes pour

nettoyer la porte du four en verre, sous peine

d’éraer la surface et de briser le verre.

Avant d’activer la fonction de nettoyage

automatique :

• nettoyer la porte du four

• enlever avec une éponge humide les

résidus les plus gros. Ne pas utiliser de

détergents ;

• sortir tous les accessoires ainsi que le

kit éventuel de glissières coulissantes ;

• ne pas placer de torchons ou de

maniques sur la poignée du four.

Lors du nettoyage automatique, les

surfaces peuvent devenir chaudes, c’est

pourquoi il convient d’éloigner les jeunes

enfants.

Ne jamais nettoyer l’appareil avec des

nettoyeurs vapeur ou haute pression.

ATTENTION : s’assurer que l’appareil est

éteint avant de procéder au remplacement

de l’ampoule, an d’éviter tout risque

d’électrocution.

! Lors de l’introduction de la grille,

s’assurer que l’arrêt est bien tourné vers

le haut et se trouve dans la partie arrière

de l’enceinte.

Assistance

Warning:

The appliance is tted with an automatic diagnostic system

which detects any malfunctions. Malfunctions are signalled

through messages of the following type: “F—” followed by

numbers.

Call for technical assistance in the event of a malfunction.

Before calling for Assistance:

• Check whether you can x the problem yourself.

• Restart the programme to check whether the malfunction

has disappeared.

• If it has not, contact the Authorised Technical Assistance

Service.

! Never use the services of an unauthorised technician.

Please have the following information to hand:

• The type of problem encountered.

• The message shown on the TEMPERATURE display.

• The appliance model (Mod.).

• The serial number (S/N).

The latter two pieces of information can be found on the

data plate located on the appliance.

Assistance

Attention :

L’appareil dispose d’un système d’autotest qui permet de

détecter toute anomalie de fonctionnement. Ces anomalies

sont afchées sous la forme: «F—» suivi de chiffres.

Contacter alors un service d’assistance technique.

Avant d’appeler le service de dépannage :

• Vérier s’il est possible de résoudre le problème soi-

même ;

• Redémarrer le programme pour contrôler si le problème

a été résolu;

• Si ce n’est pas le cas, contacter le service d’Assistance

technique agréé.

! Ne jamais faire appel à des techniciens non agréés.

Indiquer :

• le type d’anomalie;

• le code erreur afché sur l’écran TEMPERATURE

• le modèle de l’appareil (Mod.);

• son numéro de série (S/N).

Ces informations figurent sur la plaque signalétique

apposée sur l’appareil

Description of the appliance

Overall view

1 POSITION 1

2 POSITION 2

3 POSITION 3

4 POSITION 4

5 POSITION 5

6 GUIDES for the sliding racks

7 DRIPPING PAN

8 GRILL

9 Control panel

9 6

Description de l’appareil

Vue d’ensemble

1 NIVEAU 1

2 NIVEAU 2

3 NIVEAU 3

4 NIVEAU 4

5 NIVEAU 5

6 GLISSIERES de coulissement

7 Support LECHEFRITE

8 Support GRILLE

9 Tableau de bord

Description of the appliance

Control panel

1. MANUAL COOKING MODE Icons

2. PYROLYSIS selector

3. TEMPERATURE display

4. TEMPERATURE icon

5. DURATION icon

6. TIME display

7. END OF COOKING Icon

8. CONTROL PANEL LOCK icon

9. START / STOP

10. LIGHT icon

11. CLOCK icon

12. MINUTE MINDER Icon

13. TIME / TEMPERATURE ADJUSTMENT Icons

14. PREHEATING / RESIDUAL HEAT icons

15. DOOR LOCK indicator

16. AUTOMATIC/ECO COOKING MODE icons

17. CONTROL PANEL POWER BUTTON

Description de l’appareil

Tableau de bord

1. Icônes PROGRAMMES MANUELS

2. Sélection PYROLYSE

3. Afcheur TEMPERATURE

4. Icône TEMPÉRATURE

5. Icône DURÉE

6. Afcheur TEMPS

7. Icône FIN CUISSON

8. Icône VERROUILLAGE COMMANDES

9. DÉPART / ARRÊT

10. Icône ECLAIRAGE

11. Icône HORLOGE

12. Icône MINUTEUR

13. Icônes RÉGLAGE TEMPS / TEMPÉRATURE

14. Icône PRÉCHAUFFAGE / CHALEUR RÉSIDUELLE

15. Voyant PORTE VERROUILLÉE

16. Icônes PROGRAMMES AUTOMATIQUES / ECO

17. ALLUMAGE PANNEAU

Installation

! Please keep this instruction booklet in a safe place for

future reference. If the appliance is sold, given away or

moved, please make sure the booklet is also passed on to

the new owners so that they may benet from the advice

contained within it.

! Please read this instruction manual carefully: it contains

important information concerning the safe operation,

installation and maintenance of the appliance.

Positioning

! Do not let children play with the packaging material; it

should be disposed of in accordance with local separated

waste collection standards (see Precautions and tips).

! The appliance must be installed by a qualied professional

in accordance with the instructions provided. Incorrect

installation may damage property or cause harm to people

or animals.

Built-in appliances

Use an appropriate cabinet to ensure that the appliance

operates properly:

• The panels adjacent to the oven must be made of heat-

resistant material.

• Cabinets with a veneer exterior must be assembled with

glues which can withstand temperatures of up to 100°C.

• To install the oven under the counter (see diagram) or

in a kitchen unit, the cabinet must have the following

dimensions:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

558 mm.

547 mm. min.

! The appliance must not come into contact with electrical

parts once it has been installed.

The indications for consumption given on the data plate

have been calculated for this type of installation.

Ventilation

To ensure adequate ventilation, the back panel of the

cabinet must be removed. It is advisable to install the oven

so that it rests on two strips of wood, or on a completely

at surface with an opening of at least 45 x 560 mm (see

diagrams).

560 mm.

45 mm.

Centring and xing

Position the 4 tabs on the side of the oven so that they are

lined up with the 4 holes on the outer frame. Adjust the

tabs according to the thickness of the cabinet side panel,

as shown below:

20 mm thick: take off the removable

part of the tab (see diagram).;

18 mm thick: use the rst groove,

which has already been set in the

factory (see diagram).

16 mm thick: use the second

groove (see diagram).

Secure the appliance to the cabinet by opening the oven

door and putting 4 screws into the 4 holes on the outer

frame.

! All parts which ensure the safe operation of the appliance

must not be removable without the aid of a tool.

Electrical connection

Ovens equipped with a three-pole power supply cable are

designed to operate with alternating current at the voltage

and frequency indicated on the data plate located on the

appliance (see below).

Fitting the power supply cable

1. Open the terminal board

by inserting a screwdriver

into the side tabs of the

cover. Use the screwdriver

as a lever by pushing it

down to open the cover (see

diagram).

2. Install the power supply

cable by loosening the

cable clamp screw and the

three wire contact screws

L-N- .

Connect the wires to the

corresponding terminals:

the Blue wire to the terminal

marked (N), the Brown wire

to the terminal marked (L)

and the Yellow/Green wire

to the terminal marked

(see diagram).

3. Secure the cable by fastening the clamp screw.

4. Close the cover of the terminal board.

Connecting the supply cable to the mains

Install a standardised plug corresponding to the load

indicated on the data plate (see table).

The appliance must be directly connected to the mains using

an omnipolar switch with a minimum contact opening of 3

mm installed between the appliance and the mains. The

switch must be suitable for the charge indicated and must

comply with current electrical regulations (the earthing wire

must not be interrupted by the switch). The supply cable

must be positioned so that it does not come into contact

with temperatures higher than 50°C at any point (the back

panel of the oven, for example).

! The installer must ensure that the correct electrical

connection has been performed and that it is fully compliant

with safety regulations.

Before connecting the appliance to the power supply, make

sure that

• The appliance is earthed and the plug is compliant with

the law.

• The socket can withstand the maximum power of the

appliance, which is indicated on the data plate.

• The voltage is in the range between the values indicated

on the data plate.

• The socket is compatible with the plug of the appliance.

If the socket is incompatible with the plug, ask an

authorised technician to replace it. Do not use extension

cords or multiple sockets.

! Once the appliance has been installed, the power supply

cable and the electrical socket must be easily accessible.

! The cable must not be bent or compressed.

! The cable must be checked regularly and replaced by

authorised technicians only (see Assistance).

! The manufacturer declines any liability should these

safety measures not be observed.

APPLIANCE SPECIFICATIONS

Dimensions*

width 43.5 cm

height 32,4 cm

depth 41.5 cm

Volume*

59 l

Dimensions**

width 45.5 cm

height 32,4 cm

depth 41.5 cm

Volume**

62 l

Electrical

connections

voltage: 220 - 240 V~ 50 Hz

(see data plate)

maximum power absorbed

2800 W

ENERGY

LABEL

Directive 2002/40/EC on the label

of electric ovens. Standard EN 50304

Declared energy consumption

for Forced convection Class –

heating mode:

Baking

* Only for models with drawn rails.

** Only for models with wire rails.

Start-up and use

WARNING! The oven is

provided with a stop system

to extract the racks and

prevent them from coming

out of the oven (1).

As shown in the drawing,

to extract them completely,

simply lift the racks, holding

them on the front part, and

pull (2).

! The rst time you use your appliance, heat the empty oven with

its door closed at its maximum temperature for at least half an

hour. Make sure that the room is well ventilated before switching

the oven off and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective substances

used during the manufacturing process burning away.

! To make the setting process easier, press and hold the and

buttons to scroll through the numbers on the display rapidly.

! Each setting will automatically be stored in the appliance

memory after 10 seconds.

! The touch controls cannot be activated if the user is

wearing gloves.

! In order to optimise the cooking performance, when

starting the selected function, product settings will be

applied that could cause a delayed start of the fan and

heating elements.

Control panel lock

! The control panel can be locked while the oven is off, once

cooking has started or nished and during programming.

To lock the oven controls, press and hold the button

for at least 2 seconds. A buzzer will sound and the

TEMPERATURE display shows the key symbol “O—n”. The

icon will light up to indicate lock activation.

To deactivate the lock, press and hold the button again

for at least 2 seconds.

Setting the clock

! The clock can only be set when the oven is switched off. If

the oven is in standby mode, pressing the button once will

display the current time setting. Press it again to set the time.

After connection to the power supply network or after a

blackout, the button and the digits on the TIME display

will ash for 10 seconds.

To set the clock:

1. Press the button.

2. Adjust the hour gure using the and buttons.

3. Once you have reached the correct hour value, press

the button.

4. Repeat the above process to set the minutes.

If a blackout occurs, it will be necessary to reset the clock.

If the icon ashes on the display, this indicates that the

clock has not been set correctly.

Setting the minute minder

! The minute minder may be set regardless of whether the

oven is switched on or off. It does not switch the oven on or off.

When the set time has elapsed, the timer emits a buzzer

that will automatically stop after 30 seconds or when any

active button on the control panel is pressed.

To adjust the timer proceed as follows:

1. Press button .

2. Set the desired time using buttons and .

3. Once you have reached the desired value, press the

button again.

The lit symbol will remind you that the minute minder

is on.

To cancel the minute minder, press the button and use

the and buttons to set the time to 00:00. Press button

again.

The icon will switch off to indicate that the minute minder

has been disabled.

Starting the oven

1. Switch the control panel on by pressing the button.

The appliance buzzer sounds three times (ascending) and

all buttons light up in sequence.

2. Press the button corresponding to the desired cooking

mode. The TEMPERATURE display shows:

- the temperature associated with the mode, if programming

manually;

- “Auto”, if programming is automatic.

The TIME display shows:

- the current time, if programming manually;

- the duration, if programming is automatic.

3. Press the button to begin cooking.

4. The oven will begin its preheating phase, the preheating

indicators will light up as the temperature rises.

5. When the preheating process has nished, a buzzer sounds

and all the preheating indicator lights show that this stage has

been completed: the food can then be placed in the oven.

6. During cooking it is always possible to:

- change the temperature by pressing the button,

followed by the and buttons (manual modes only);

- set the duration of a cooking mode (see Cooking Modes);

- press the button to stop cooking. In this case the

appliance stores the temperature modied previously in its

memory (manual modes only);

- switch off the oven by pressing the button for 3 seconds.

7. If a blackout occurs while the oven is already in operation,

an automatic system within the appliance will reactivate the

cooking mode from the point at which it was interrupted,

provided that the temperature has not dropped below a

certain level. Programmed cooking modes which have not

yet started will not be restored and must be reprogrammed

(for example: a cooking mode has been programmed to

start at 20:30. At 19:30 a blackout occurs. When the power

supply is restored, the mode will have to be reprogrammed).

! There is no preheating stage for the GRILL mode.

! Never put objects directly on the bottom of the oven; this

will prevent the enamel coating from being damaged.

! Always place cookware on the rack(s) provided.

Cooling ventilation

In order to cool down the external temperature of the oven, a

cooling fan blows a stream of air between the control panel and

the oven door, as well as towards the bottom of the oven door.

At the beginning of the PYROLISIS mode, the cooling fan

operates at low speed.

! Once cooking has been completed, the cooling fan continues

to operate until the oven has cooled down sufciently.

Oven light

The light comes on when the oven door is opened or when

a cooking mode starts.

The button can be used to switch on the light at any time.

Residual heat indicators

The appliance is tted with a residual heat indicator. When

the oven is off, the “residual heat” bar on the display lights

up to indicate high temperatures inside the oven cavity. The

individual segments of the bar switch off one by one as the

temperature inside the oven falls.

Demo mode

The oven can operate in the DEMO mode: all heating

elements are deactivated, and the controls remain operative.

To activate DEMO mode, press and release button ,

then buttons and simultaneously for 6 seconds, and

then press and release button .

A buzzer sounds and the TEMPERATURE display shows

“dEon”. To deactivate DEMO mode, when the oven is off

press and hold button and button simultaneously

for 3 seconds. A buzzer sounds and the “dEoF” message

disappears from the display.

Restoring the factory settings

The oven factory settings can be restored to reset all

selections made by the user (clock and customised

durations). To carry out a reset, switch off the oven, then

press and hold the button corresponding to the rst manual

cooking mode (top left) and the button simultaneously

for 6 seconds. Once the restore procedure is complete, a

buzzer will sound. The rst time the button is pressed, the

oven will behave as if it is being switched on for the rst time.

Standby

This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode. If no buttons are pressed for 30

minutes and the control panel/door lock has not been

activated, the appliance automatically reverts to standby

mode. Standby mode is indicated by the high luminosity

“Clock button” light. As soon as interaction with the machine

resumes, the system’s operating mode is restored.

Modes

! Every time the oven is switched on, it suggests the rst

manual cooking mode.

Manual cooking modes

! All cooking modes have a default cooking temperature which

may be adjusted manually to a value between 30°C and

250°C as desired (300°C for GRILL mode). Any temperature

adjustments will be stored in the appliance memory and

suggested again the next time this mode is used. If the

selected temperature is lower than the temperature inside the

oven, the text “Hot” appears on the TEMPERATURE display.

However, it will still be possible to start cooking.

MULTILEVEL mode

All heating elements and the fan are activated. Since the

heat remains constant throughout the oven, the air cooks

and browns food in a uniform manner. A maximum of two

racks may be used at the same time.

BARBECUE mode

The top heating element and the rotisserie spit (where

present) are activated. The high and direct temperature

of the grill is recommended for food which requires a high

surface temperature. Always cook in this mode with the oven

door closed (see “Practical cooking advice”).

TURNSPIT mode

The function is ideal for turnspit cooking. Always cook in

this mode with the oven door closed.

FAN GRILLING mode

The top heating element and the rotisserie spit (where

present) are activated and the fan begins to operate.

During part of the cycle the circular heating element is

also activated. This combination of features increases the

effectiveness of the unidirectional thermal radiation provided

by the heating elements through the forced circulation of

the air throughout the oven.

This helps prevent food from burning on the surface and

allows the heat to penetrate right into the food. Always

cook in this mode with the oven door closed (see “Practical

cooking advice”).

PIZZA modes

The top and circular heating elements switch on and the fan

begins to operate. This combination heats the oven rapidly.

If you use more than one rack at a time, switch the position

of the dishes halfway through the cooking process.

BAKING mode

The rear heating element and the fan are switched on, thus

guaranteeing the distribution of heat in a delicate and uniform

manner throughout the entire oven. This mode is ideal for baking

temperature sensitive foods (such as cakes, which need to rise).

Rotisserie spit*

To operate the rotisserie

function (see diagram)

proceed as follows:

1. Place the dripping pan in

position 1.

2. Place the rotisserie

support in position 3 and

insert the spit in the hole

provided on the back panel

of the oven.

3. Start the rotisserie

function by selecting the modes;

! When mode is on, the rotisserie will stop if the door is

opened.

Automatic cooking modes

! The temperature and cooking duration are pre-set values,

guaranteeing a perfect result every time - automatically. These

values are set using the C.O.P.® (Programmed Optimal

Cooking) system. The cooking cycle stops automatically and

the oven indicates when the dish is cooked. You may start

cooking whether the oven has been preheated or not.

The cooking duration can be customised according to

personal taste by modifying the relevant value - before

cooking begins - by ±5/20 minutes depending on the

selected programme. The duration can however be modied

even once cooking has begun. If the value is modied

before the programme begins, it is stored in the memory

and suggested again by the appliance when the programme

is next used. If the temperature inside the oven is higher

than the suggested value for the selected mode, the text

“Hot” appears on the TEMPERATURE display and it will

not be possible to begin cooking; wait for the oven to cool.

! When the cooking stage has been reached, the oven

buzzer sounds.

! Do not open the oven door as this will disrupt the cooking

time and temperature.

ROAST mode

Use this function to cook beef, veal, pork, chicken and lamb.

Place the food inside the oven while it is still cold. The dish

may also be placed in a preheated oven.

CHICKEN mode

This function is ideal for cooking chicken (whole or in

pieces). Place the food inside the oven while it is still cold.

The dish may also be placed in a preheated oven.

BAKED CAKES mode

This function is ideal for cooking desserts which are made

using natural yeast, baking powder and desserts which

contain no yeast. Place the dish in the oven while it is still

cold. The dish may also be placed in a preheated oven.

TARTS mode

This function is ideal for all tart recipes (which normally need

to be heated well from underneath). Place the food inside

the oven while it is still cold.

The dish may also be placed in a preheated oven.

PASTRIES mode

This function is ideal for baked desserts (made using natural

yeast). Place the food inside the oven while it is still cold;

the dish may also be placed in a preheated oven if desired.

BREAD mode

Use this function to bake bread. To obtain the best results,

we recommend that you carefully observe the instructions

below:

• follow the recipe;

• do not exceed the maximum weight of the dripping pan;

• remember to pour 50 g (0,5 dl) of cold water into the

baking tray in position 5.

• The dough must be left to rise at room temperature for

1 – 1 ½ hours (depending on the room temperature) or

until the dough has doubled in size.

Recipe for BREAD:

1 Dripping pan holding 1000 g Max, lower level

2 Dripping pans each holding 1000 g Max, medium and

lower levels

Recipe for 1000 g of dough: 600 g our, 360 g water, 11g

salt, 25 g fresh yeast (or 2 sachets of powder yeast)

Method:

• Mix the our and salt in a large bowl.

• Dilute the yeast in lukewarm water (approximately 35

degrees).

• Make a small well in the mound of our.

• Pour in the water and yeast mixture.

• Knead the dough by stretching and folding it over itself

with the palm of your hand for 10 minutes until it has a

uniform consistency and is not too sticky.

• Form the dough into a ball shape, place it in a large bowl

and cover it with transparent plastic wrap to prevent the

surface of the dough from drying out. Select the manual

LOW TEMPERATURE function on the oven and set the

temperature to 40°C. Place the bowl inside and leave

the dough to rise for approximately 1 hour (the dough

should double in volume).

• Cut the dough into equal sized loaves.

• Place them in the dripping pan, on a sheet of baking

paper.

• Dust the loaves with our.

• Make incisions on the loaves.

• Place the food inside the oven while it is still cold.

• Start the BREAD cooking mode.

* Only available in certain models.

• Once baked, leave the loaves on one of the grill racks

until they have cooled completely.

Programming cooking

! A cooking mode must be selected before programming

can take place.

! Once a cooking mode has been selected, the button

is activated; it will then be possible to program a duration.

The button is only activated after a duration has been

set; it will then be possible to program a delayed start.

Programming the duration

1. Press the button; the button and the numbers on

the TIME display will ash.

2. Set the duration by pressing buttons and .

3. Once you have reached the desired duration, press the

button again.

4. Press the button to begin cooking.

5. When cooking has nished, “END” appears on the

TEMPERATURE display and a buzzer sounds.

• For example: it is 9:00 a.m. and a duration of 1 hour and

15 minutes is programmed. The programme will stop

automatically at 10:15 a.m.

Programming delayed cooking

! A cooking duration must be set before the cooking end

time can be scheduled.

! For the delayed programming to work properly, the clock

should be set to the correct time.

1. Press the button and repeat steps 1 to 3 as described

for the duration setting.

2. Then press the button and set the end time using

the and buttons.

3. Once you have reached the desired end time, press the

button again.

4. Press the button to activate the programmed mode.

The and buttons will ash alternately to indicate that

programming has taken place; in the time before cooking

starts, the TIME display will show the duration and the

cooking end time alternately.

5. Once cooking has finished, “END” appears on the

TEMPERATURE display and a buzzer sounds.

• For example: it is 9:00 a.m. and a time of 1 hour and 15

minutes is programmed, while the end time is set to 12:30.

The programme will start automatically at 11:15 a.m.

To cancel programming press the button.

Practical cooking advice

! Do not place racks in position 1 and 5 during fan-assisted

cooking. This is because excessive direct heat can burn

temperature sensitive foods.

! In the GRILL and FAN GRILLING cooking modes,

particularly when using the rotisserie spit, place the dripping

pan in position 1 to collect cooking residues (fat and/or

grease).

MULTILEVEL

• Use positions 2 and 4, placing the food which requires

more heat on 2.

• Place the dripping pan on the bottom and the rack on

top.

GRILL

• Place the rack in position 3 or 4. Position the food in the

centre of the rack.

• We recommend that the temperature is set to its

maximum level. The top heating element is regulated by

a thermostat and may not always operate constantly.

PIZZA

• Use a lightweight aluminium pizza pan. Place it on the

rack provided.

For a crispy crust, do not use the dripping pan as this

extends the total cooking duration and prevents the crust

from forming.

• If the pizza has a lot of toppings, we recommend adding

the mozzarella cheese to the top of the pizza halfway

through the cooking process.

Modes Foods Weight

(in kg)

Preheating

Manual

Standard

guide

rails

Sliding

guide

rails

Multilevel*

1+1

2 and 4

1 and 2/3

1 or 2

2 and 4

1 and 3

yes

20-25

30-35

20-30

65-75

45-50

30-35

35-40

20-25

10-20

20-25

25-35

Grill*

0,7

0,5

0,8

0,7

n° 4 or 5

n° 4 or 6

3 or 4

2 or 3

300

10-20

10-15

15-20

10-20

10-12

3-5

70-80

Fan grilling*

1,5

210

200

210

55-60

30-35

70-80

60-70

60-75

70-80

40-45

Pizza*

Pizza

Focaccia bread

0,5

yes

15-20

20-25

Baking*

0,5

0,7

0,6

0,7

0,8

0,5

2 or 3

2 and 4

2 or 3

1 and 3

1 or 2

1 and 3

1 or 2

1 and 2

yes

180

180-190

160-170

180-190

180

200

210

25-35

40-50

45-55

20-25

35-40

20-30

20-25

30-35

180

20-25

Automatic**

Roast

Roast dishes12 or 32 no

Bread***

Bread (see recipe)

11 or 21 no

Baked cakes

12 or 32 no

Tarts

0,52 or 32 no

Cooking advice table

Rack position Recommended

Temperature

(°C)

Cooking

duration

(minutes)

1 and 3 and 5

1 and 2 and 4

50 0,5

210-220

180

160-170

200-210

190-200

180

180-190

190

180

210

190-200

210-220

190-200

Turnspit*

Chicken on the turnspit

Duck on the turnspit

Chicken

Chicken/poultry

Pastries

1,5

250

70-80

60-70

1,2-1,5

2 o 32 no

Precautions and tips

! This appliance has been designed and manufactured

in compliance with international safety standards. The

following warnings are provided for safety reasons and

must be read carefully.

General safety

• The appliance was designed for domestic use inside the

home and is not intended for commercial or industrial use.

• The appliance must not be installed outdoors, even in

covered areas. It is extremely dangerous to leave the

appliance exposed to rain and storms.

• When moving or positioning the appliance, always use

the handles provided on the sides of the oven.

• Do not touch the appliance while barefoot or with wet or

damp hands and feet.

• The appliance must be used by adults only for

the preparation of food, in accordance with the

instructions provided in this booklet. Any other

use of the appliance (e.g. for heating the room)

constitutes improper use and is dangerous. The

manufacturer may not be held responsible for any

damage caused as a result of improper, incorrect

and unreasonable use of the appliance.

• Do not touch the heating elements or certain parts

of the oven door when the appliance is in use; these

parts become extremely hot. Keep children well away

from the appliance.

• Make sure that the power supply cables of other electrical

appliances do not come into contact with the hot parts of

the oven.

• The ventilation and heat dispersal openings must never

be obstructed.

• Always grip the oven door handle in the centre: the ends

may be hot.

• Always use oven gloves when placing cookware in the

oven or when removing it.

• Do not use aluminium foil to line the bottom of the oven.

• Do not place ammable materials in the oven: if the

appliance is switched on accidentally, the materials could

catch re.

• When unplugging the appliance, always pull the plug

from the mains socket; do not pull on the cable.

• Do not perform any cleaning or maintenance work without

having disconnected the appliance from the electricity

mains.

• If the event of malfunctions, under no circumstances

should you attempt to perform the repairs yourself.

Contact an authorised Service Centre (see Assistance).

• Do not rest objects on the open oven door.

• Do not let children play with the appliance.

• The appliance should not be operated by people (including

children) with reduced physical, sensory or mental

capacities, by inexperienced individuals or by anyone

who is not familiar with the product. These individuals

should, at the very least, be supervised by someone who

assumes responsibility for their safety or receive preliminary

instructions relating to the operation of the appliance.

• The appliance is not intended to be operated by

means of an external timer or separate remote-

control system.

Disposal

• When disposing of packaging material: observe local

legislation so that the packaging may be reused.

• The European Directive 2012/19/EC on Waste

Electrical and Electronic Equipment (WEEE), requires

that old household electrical appliances must not

be disposed of in the normal unsorted municipal

waste stream. Old appliances must be collected

separately in order to optimise the recovery and

recycling of the materials they contain and reduce

the impact on human health and the environment.

The crossed out “wheeled bin” symbol on the product

reminds you of your obligation, that when you dispose

of the appliance it must be separately collected.

Consumers should contact their local authority or retailer

for information concerning the correct disposal of their

old appliance.

Respecting and conserving the environment

• You can help to reduce the peak load of the electricity

supply network companies by using the oven in the

hours between late afternoon and the early hours of

the morning. The cooking mode programming options,

the “delayed cooking” mode (see Cooking modes) and

“delayed automatic cleaning” mode (see Care and

Maintenance) in particular, enable the user to organise

their time efciently.

• Always keep the oven door closed when using the GRILL

and FAN GRILLING modes: this will achieve improved

results while saving energy (approximately 10%).

• Check the door seals regularly and wipe them clean

to ensure they are free of debris so that they adhere

properly to the door, thus avoiding the dispersal of heat.

! This product complies with the requirements of the latest

European Directive on the limitation of power consumption

of the standby mode.

Maintenance and care

Switching the appliance off

Disconnect your appliance from the electricity supply before

carrying out any work on it.

Cleaning the appliance

• Slight differences in colour on the front of the oven are due

to the different materials used, i.e. glass, plastic or metal.

• Any shady areas resembling grooves on the oven door

glass are caused by reections from the oven light.

• The enamel is branded at very high temperatures. This

process may cause colour variations. This is normal and

will not affect appliance operation in any way. The thin

edges of the sheet metal cannot be entirely enamelled

and may therefore appear to be unnished. This will not

affect the rust protection.

• The stainless steel or enamel-coated external parts and

the rubber seals may be cleaned using a sponge that

has been soaked in lukewarm water and neutral soap.

Use specialised products for the removal of stubborn

stains. After cleaning, rinse and dry thoroughly. Do not

use abrasive powders or corrosive substances.

• The inside of the oven should ideally be cleaned after

each use, while it is still lukewarm. Use hot water and

detergent, then rinse well and dry with a soft cloth. Do

not use abrasive products.

• All accessories - with the exception of the sliding racks

- can be washed like everyday crockery, and are even

dishwasher safe.

• We recommend that detergents are not sprayed directly

onto the control panel, but that a sponge is used instead.

! Never use steam cleaners or pressure cleaners on the

appliance.

Cleaning the oven door

Clean the glass part of the oven door using a sponge and

a non-abrasive cleaning product, then dry thoroughly with

a soft cloth. Do not use rough abrasive material or sharp

metal scrapers as these could scratch the surface and cause

the glass to crack.

For more thorough cleaning purposes, the oven door may

be removed:

1. Open the oven door fully (see diagram).

2. Use a screwdriver to lift up and turn the small levers F

located on the two hinges (see diagram).

3. Grip the door on the two outer

sides and close it approximately

half way. Pull the door towards you,

lifting it out of its slot (see diagram).

To replace the door, reverse this

sequence.

Inspecting the seals

Check the door seals around the oven regularly. If the seals

are damaged, please contact your nearest Service Centre

(see Assistance). We recommend that the oven is not used

until the seals have been replaced.

Replacing the light bulb

To replace the oven light

bulb:

1. Remove the glass cover

of the lamp-holder.

2. Remove the light bulb and

replace it with a similar one:

halogen lamp voltage 230 V,

wattage 25 W, cap G 9.

3. Replace the glass cover

(see diagram).

! Do not touch the light bulb directly with your hands.

Glass cover

Lamp

Holder

compartment

! Do not use the oven lamp as/for ambient lighting.

Automatic cleaning with the PYROLYSIS

function

With the PYROLYSIS mode, the internal temperature of the

oven reaches 500°C. The pyrolytic cycle is activated, burning

away food and grime residues. Dirt is literally incinerated.

Keep children away from the appliance during the automatic

cleaning cycle as surfaces may become very hot. Particles

may ignite inside the oven as a result of the combustion

process. There is no cause for concern: this process is both

normal and hazard-free.

Before initiating the PYROLYSIS mode:

• clean the oven door;

• remove large or coarse food residues from the inside of

the oven using a damp sponge. Do not use detergents;

• remove all accessories and the sliding rack kit (where

present);

• do not place tea towels or pot holders over the oven

handle.

! If the oven is too hot, the pyrolytic cycle may not start.

Wait for the oven to cool down.

! The programme may only be started once the oven door

has been closed.

To activate the PYROLYSIS programme:

1. Switch the control panel on by pressing the button.

2. Press the button; the TIME display will show the default

duration of 1:30 h (normal cycle), while he TEMPERATURE

display will show “Piro” and “nor” alternately;

3. The desired cleaning level can be selected by pressing

the button, then:

- pressing to switch to the intensive cycle: the duration is

2 h and the TEMPERATURE display shows the text “Piro”

and “int” alternately;

- pressing to switch to the economy cycle: the duration is

1 h and the TEMPERATURE display shows the text “Piro”

and “eco” alternately.

Safety devices

• the door locks automatically as soon as the temperature

reaches a high value; the icon lights up on the

display;

• pressing the button cancels the cleaning cycle t any

time;

• if a malfunction occurs, the heating elements will be

switched off;

• once the oven door has been locked, you cannot change

the duration and end time settings.

Programming delayed automatic cleaning

! Programming is possible only after selecting the

PYROLYSIS mode.

1. Press the button and set the end time using the

and buttons.

2. Once you have reached the desired end time, press the

button again.

3. Press the button to activate the programmed mode.

4. When the selected time has elapsed, “END” appears on

the TEMPERATURE display and a buzzer sounds.

• For example: it is 9:00 a.m. and the Economy (ECO)

PYROLYSIS level has been selected, with the default

duration of 1 hour. 12:30 is scheduled as the end time.

The programme will start automatically at 11:30 a.m.

The icons and ash to indicate that programming

has taken place. After programming, in the time before the

PYROLYSIS mode starts, the TIME display indicates the

duration and end of the PYROLYSIS mode alternately.

To cancel programming press the button.

Once the automatic cleaning cycle is over

Before you can open the oven door, you will have to wait

for the icon to switch off: this indicates the oven

temperature has dropped to an acceptable level. You will

notice some white dust deposits on the bottom and the sides

of your oven; remove these deposits with a damp sponge

once the oven has cooled down completely. Alternatively,

you can make use of the already heated oven, in which

case it is not necessary to remove the deposits, they are

completely harmless and will not affect your food in any way.

Troubleshooting

Problem

Possible cause

Solution

The appliance has just been

connected to the electricity mains

or there has been a blackout.

Set the clock.

A programmed cooking mode

does not start.

There has been a blackout. Reprogram the cooking mode.

Only the high luminosity

“Clock button” is lit.

The appliance is in standby mode Press any button to exit

standby mode.

The temperature inside the oven

is higher than the suggested

value for the selected mode.

Wait for the oven to cool down.

Fan-assisted cooking has been

selected and the food looks burnt.

Positions 1 and 5: the direct

heat could cause

temperature-sensitive

foods to burn.

We recommend switching

dripping pan positions halfway

through cooking.

The “Clock button” and the

digits on the display flash.

An automatic mode has been

selected. “Hot” appears on the

display and cooking does not

start.

Installation

! Conservez ce mode d’emploi pour pouvoir le consulter

à tout moment. En cas de vente, de cession ou de

déménagement, veillez à ce qu’il suive l’appareil pour

informer le nouveau propriétaire sur son fonctionnement

et lui fournir les conseils correspondants.

! Lisez attentivement les instructions : elles contiennent

des conseils importants sur l’installation, l’utilisation et la

sécurité de votre appareil

Positionnement

! Les emballages ne sont pas des jouets pour enfants, il

faut les mettre au rebut en respectant la réglementation

sur le tri sélectif des déchets (voir Précautions et conseils).

! L’installation doit être effectuée par un professionnel du

secteur conformément aux instructions du fabricant. Une

mauvaise installation peut causer des dommages à des

personnes, des animaux ou des biens.

Encastrement

Pour garantir le bon fonctionnement de l’appareil, il faut

que le meuble possède des caractéristiques bien précises:

• les panneaux adjacents doivent être fabriqués dans un

matériau résistant à la chaleur;

• dans le cas de meubles en plaqués bois, les colles

doivent pouvoir résister à une température de 100 °C;

• la cavité du meuble pour encastrement du four, tant

sous plan (voir gure) qu’en colonne , doit avoir les

dimensions suivantes:

595 mm.

25 mm.

545 mm.

5 mm.

567 mm.

23 mm.

575-585 mm.

45 mm.

558 mm.

547 mm. min.

! Après encastrement de l’appareil, il ne doit plus y avoir

possibilité de contact avec les parties électriées.

Les déclarations de consommation indiquées sur la plaque

signalétique ont été mesurées pour ce type d’installation.

Aération

Pour garantir une bonne aération, la cavité d’encastrement

doit être dépourvue de paroi arrière. Il est conseillé

d’installer le four de manière à ce qu’il repose sur deux

cales en bois ou bien sur un plan d’appui continu qui ait une

découpe d’au moins 45 x 560 mm (voir gures).

560 mm.

45 mm.

Centrage et xation

Positionner les 4 taquets situés sur les côtés du four en

face des 4 trous pratiqués sur le cadre et les régler selon

l’épaisseur de la joue du meuble :

épaisseur 20 mm : enlever la partie

amovible du taquet (voir figure);

épaisseur 18 mm : utiliser la

première rainure, comme prévu

par le fabricant (voir figure);

épaisseur 16 mm : utiliser la

deuxième rainure (voir figure).

Pour xer l’appareil au meuble : ouvrir la porte du four et

visser 4 vis à bois dans les 4 trous du cadre.

! Toutes les parties qui servent de protection doivent être

xées de manière à ne pouvoir être enlevées qu’avec l’aide

d’un outil.

Raccordement électrique

Les fours munis d’un câble d’alimentation tripolaire sont prévus

pour un fonctionnement au courant alternatif à la tension et

à la fréquence indiquées sur la plaque signalétique apposée

sur l’appareil (voir ci-dessous).

Montage du câble d’alimentation

1. Pour ouvrir le bornier,

faire pression à l’aide d’un

tournevis sur les languettes

latérales du couvercle : tirer

et ouvrir le couvercle (voir

gure).

2. Montage du câble

d’alimentation : dévisser la

vis du serre-câble ainsi que

les trois vis des contacts

L-N- puis fixer les fils

sous les têtes de vis en

respectant les couleurs Bleu

(N) Marron (L) Jaune-Vert

(voir gure).

3. Fixer le câble dans le

serre-câble prévu.

4. Fermer le couvercle du

bornier.

Branchement du câble d’alimentation au réseau électrique

Montez sur le câble une prise normalisée adaptée à la

charge indiquée sur l’étiquette des caractéristiques.

En cas de raccordement direct au réseau, il faut intercaler entre

l’appareil et le réseau un interrupteur à coupure omnipolaire

ayant au moins 3 mm d’écartement entre les contacts,

dimensionné à la charge et conforme aux normes en vigueur

(le l de terre ne doit pas être interrompu par l’interrupteur).

Le câble d’alimentation ne doit atteindre, en aucun point, des

températures dépassant de 50°C la température ambiante.

! L’installateur est responsable du bon raccordement

électrique de l’appareil et du respect des normes de sécurité.

Avant de procéder au branchement, assurez-vous que :

• la prise est bien munie d’une terre conforme à la loi;

• la prise est bien apte à supporter la puissance maximale

de l’appareil, indiquée sur la plaquette signalétique;

• la tension d’alimentation est bien comprise entre les

valeurs indiquées sur la plaquette signalétique;

• la prise est bien compatible avec la che de l’appareil.

Si ce n’est pas le cas, remplacez la prise ou la che,

n’utilisez ni rallonges ni prises multiples.

! Après installation de l’appareil, le câble électrique et la

prise de courant doivent être facilement accessibles

! Le câble ne doit être ni plié ni excessivement écrasé.

! Il doit être contrôlé périodiquement et ne peut être

remplacé que par un technicien agréé (voir Assistance).

! Nous déclinons toute responsabilité en cas de non

respect des normes énumérées ci-dessus.

* Uniquement pour les modèles avec glissières embouties.

** Uniquement pour les modèles avec glissières en fil.

PLAQUE SIGNALETIQUE

Dimensions*

largeur 43,5 cm

hauteur 32,4 cm

profondeur 41,5 cm

Volume*

L. 59

Raccordements

électriques

tension 220-240V~ 50Hz

(voir plaque signalétique)

puissance maximum absorbée

2800W

ENERGY

LABEL*

(ETIQUETTE

ENERGIE *)

Directive 2002/40/CE sur l'étiquette

des fours électriques

Norme EN 50304

Consommation énergie déclaration

Classe convection Forcée –

fonction four: PÂTISSERIE

Cet appareil est conforme aux

Directives Communautaires

suivantes : 2006/95/CEE du

12.12.06 (Basse Tension) et

modifications successives -

2004/108/CEE du 15.12.04

(Compatibilité Électromagnétique)

et modifications successives -

93/68/CEE du 22/07/93 et

modifications successives.

- 2012/19/CE et modifications

successives.

- 1275/2008 standby/off mode

Dimensions**

largeur 45,5 cm

hauteur 32,4 cm

profondeur 41,5 cm

Volume**

L. 62

Mise en marche et utilisation

ATTENTION! Le four

est équipé d’un système

d’arrêts de grilles qui

permet de les retirer sans

que ces dernières sortent

entièrement du four (1).

Pour sortir complètement

les grilles il suft, comme

illustré, de les soulever en

les saisissant par l’avant et de les tirer (2).

! Lors de son premier allumage, faire fonctionner le four à

vide, porte fermée, pendant au moins une heure en réglant

le thermostat sur le maximum. Puis éteindre le four, ouvrir

la porte et aérer la pièce. L’odeur qui se dégage est due

à l’évaporation des produits utilisés pour protéger le four.

! Pour simplier les sélections, garder les touches « » et

« » enfoncées ; les numéros délent plus rapidement.

! Chaque sélection est automatiquement mémorisée

pendant 10 secondes.

! Quand on porte les gants, il est impossible d’actionner

les touches.

! Pour optimiser les performances de cuisson, un réglage

des paramètres du produit est effectué au moment

de l’activation de la fonction sélectionnée, ceci peut

entraîner un retard d’allumage du ventilateur et des

éléments chauffants.

Verrouillage de commandes

! Les commandes peuvent être verrouillées four éteint,

cuisson en cours ou terminée ou bien en programmation.

Pour verrouiller les commandes du four, appuyer sur la

touche pendant au moins 2 secondes. Un signal sonore

retentit et le symbole clé «O--n» apparaît sur l’afcheur

TEMPÉRATURE. L’icône allumée indique que le

verrouillage est activé.

Pour déverrouiller, appuyer à nouveau sur la touche

pendant au moins 2 secondes.

Régler l’horloge

! L’horloge n’est réglable que four éteint. Si le four est en mode

veille (standby), une première pression sur la touche afche

l’heure courante. Appuyer à nouveau pour régler l’heure.

Après branchement au secteur ou après une panne de

courant, la touche et les chiffres de l’afcheur TEMPS

se mettent à clignoter pendant 10 secondes.

Pour régler l’horloge :

1. Appuyer sur la touche .

2. Régler l’heure à l’aide des touches et .

3. Une fois l’heure exacte atteinte, appuyer à nouveau sur

la touche .

4. procéder comme sus-indiqué pour les minutes aussi.

En cas de panne de courant, il faut remettre l’horloge à

l’heure. L’icône qui clignote sur l’afcheur signale que

l’horloge a besoin d’être réglée.

Régler le minuteur

! Le minuteur est toujours réglable tant four éteint que four

allumé. Il ne contrôle pas l’allumage et l’arrêt du four.

Une fois le temps écoulé, le minuteur émet un signal sonore

qui s’arrête automatiquement au bout de 30 secondes ou

après avoir appuyé sur une touche active quelconque.

Pour régler la minuterie :

1. Appuyer sur la touche .

2. Sélectionner le temps désiré à l’aide des touches et

3. Une fois la sélection voulue atteinte, appuyer à nouveau

sur la touche .

L’icône allumée signale que le minuteur est activé.

Pour annuler la sélection de la minuterie, appuyer sur la

touche et à l’aide des touches et ramener le temps

à 00:00. Appuyer à nouveau sur la touche .

L’icône éteinte signale que le minuteur est désactivé.

Mise en marche du four

1. Appuyer sur la touche pour allumer le panneau de

commande. L’appareil émet un triple son ascendant et

toutes les touches s’allument à la suite.

2. Appuyer sur la touche du programme de cuisson

souhaité. L’écran TEMPÉRATURE afche :

- en cas de programme manuel, la température associée

au programme ;

- «Auto» en cas de programme automatique.

l’écran TEMPS afche :

- en cas de programme manuel, l’heure courante ;

- la durée en cas de programme automatique.

3. Appuyer sur la touche pour démarrer la cuisson.

4. Le four se place en préchauffage, les indicateurs de

montée en température s’éclairent progressivement au fur

et à mesure que la température augmente.

5. Un signal sonore suivi de l’allumage de tous les

indicateurs de préchauffage signale la n du préchauffage.

Il est temps d’enfourner les plats.

6. En cours de cuisson, il est possible à tout moment de :

- modier la température en appuyant sur les touches

puis sur les touches et (seuls programmes manuels) ;

- programmer la durée d’une cuisson (voir Programmes) ;

- stopper la cuisson en appuyant sur la touche . Dans ce cas,

l’appareil se rappelle de la température éventuellement modiée

précédemment (uniquement pour programmes manuels).

- éteindre le four en gardant la touche enfoncée pendant

3 secondes.

7. En cas de coupure de courant, si la température du four

n’est pas trop redescendue, un dispositif spécial fait repartir

le programme à partir du moment où il a été interrompu. Les

programmations en attente de démarrage ne sont par contre

pas rétablies et doivent être reprogrammées dès rétablissement

du courant (par exemple : un départ de cuisson a été

programmé à 20h30. A 19h30, il y a une coupure de courant.

Après rétablissement du courant, il faut reprogrammer).

! Aucun préchauffage n’est prévu pour le programme

BARBECUE.

! Ne jamais poser d’objets à même la sole du four, l’émail

risque de s’abîmer.

! Il faut toujours enfourner les plats sur la grille fournie avec

l’appareil.

Ventilation de refroidissement

Pour obtenir un abaissement des températures extérieures,

un système de refroidissement soufe de l’air à l’extérieur

par une fente située entre le tableau de bord, la porte du

four et la partie basse de la porte du four.

Au début du programme PYROLYSE le système fonctionne

à faible vitesse.

! Le ventilateur continue à tourner après l’arrêt du four

jusqu’à ce que ce dernier se soit sufsamment refroidi.

Eclairage du four

L’éclairage s’allume à l’ouverture de la porte du four ou au

démarrage d’un programme de cuisson.

La touche permet d’allumer ou éteindre l’éclairage à

tout moment.

Indicateurs de chaleur résiduelle

Cet appareil est équipé d’un indicateur de chaleur résiduelle.

Four éteint, l’afcheur signale par allumage de la barre de

“chaleur résiduelle” la présence de température à l’intérieur

de l’enceinte. Les éléments de la barre s’éteignent au fur

et à mesure que la température à l’intérieur du four baisse.

Mode Demo (Démonstration)

Le four peut fonctionner en mode DEMO : dans ce cas,

tous les éléments chauffants sont désactivés et seules les

commandes fonctionnent.

Pour activer le mode DEMO, appuyer brièvement sur la touche

, puis sur les touches et simultanément pendant 6

secondes, appuyer ensuite brièvement sur la touche .

Un signal sonore retentit et le message « dEon » apparaît

sur l’afcheur TEMPÉRATURE.

Pour désactiver le mode de fonctionnement DEMO, quand

le four est éteint, appuyer simultanément sur la touche

et sur la touche pendant 3 secondes. Un signal sonore

retentit et le message « dEof » est afché.

Rétablissement des réglages d’usine

Le four peut retourner à ses paramètres de réglage usine, il

suft pour cela de réinitialiser toutes les sélections effectuées par

l’utilisateur (horloge et durées personnalisées). Pour procéder à

la réinitialisation, éteindre le four, garder enfoncées pendant 6

secondes de suite la touche de la première cuisson manuelle

en haut à gauche ainsi que la touche . Une fois que la

réinitialisation a eu lieu, un signal sonore retentit. Dès la première

pression sur la touche il y a retour à la première mise en service.

Standby

Ce produit est conforme à la nouvelle Directive européenne

sur la réduction de la consommation d’énergie en mode veille

(standby). Sans opérations pendant 30 minutes et si aucun

verrouillage de touches ou de porte n’a été sélectionné,

l’appareil se place automatiquement en mode veille. Le mode

standby est signalé par l’intense luminosité de la «touche

horloge». A la moindre intervention sur l’appareil, le système

se remet en mode de fonctionnement normal.

Programmes

! A chaque allumage, le four propose le premier programme

de cuisson manuel.

Programmes de cuisson manuels

! Tous les programmes ont une température de cuisson

présélectionnée. Il est possible de la régler manuellement,

entre 30°C et 250°C au choix (300°C pour le programme

BARBECUE). Toute modication de la température sera

mémorisée et reproposée dès la prochaine utilisation du

programme. Si la température choisie est inférieure à la

température intérieure du four, l’afcheur TEMPÉRATURE

afche « Hot ». Il est toutefois possible de démarrer la cuisson.

Programme MULTINIVEAUX

Mise en marche de tous les éléments chauffants ainsi que

de la turbine. La chaleur est constante et bien répartie à

l’intérieur du four, l’air cuit et dore de façon uniforme en

tous points. Il est possible de cuire au maximum sur deux

niveaux en même temps.

Programme BARBECUE

Mise en marche de la résistance de voûte et du tournebroche

(si l’appareil en est équipé). La température élevée et directe

du gril est conseillée pour tous les aliments qui exigent une

haute température en surface. La cuisson doit avoir lieu

porte du four fermée (voir « Conseils de cuisson »).

Programme TOURNEBROCHE

Cette fonction est optimisée pour les cuissons au

tournebroche. Cuissons porte du four fermée.

Programme GRATIN

Mise en marche de la résistance de voûte, de la résistance

circulaire (pendant un certain temps) et de la turbine et

du tournebroche (si l’appareil en est équipé). L’irradiation

thermique unidirectionnelle s’ajoute au brassage de l’air pour

une répartition uniforme de la chaleur dans l’enceinte du four.

Plus de risque de brûler les aliments en surface et plus

grande pénétration de la chaleur. La cuisson doit avoir lieu

porte du four fermée (voir « Conseils de cuisson »).

Programme PIZZA

Mise en marche de la résistance de voûte et de la résistance

circulaire ainsi que de la turbine. Cette combinaison permet

une montée en température rapide du four. En cas de

La page charge ...

Scholtes FRI 886.1 MT Mode d'emploi

Marque: Scholtes

Modèle: FRI 886.1 MT

Catégorie: Fours

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Scholtes FRI 886.1 MT User guide

Scholtes FRI 886.1 MT Mode d'emploi

Scholtes FRI 886.1 MT Mode d'emploi

dans d''autres langues

Autres documents