Futaba R2106GF Manuel utilisateur

Futaba
Marque
Futaba
Modèle
R2106GF
Catégorie
Antennes réseau
Taper
Manuel utilisateur
FUTABA CORPORATION
oak kandakajicho 8F 3-4 Kandakajicho, Chiyoda-ku, Tokyo 101-0045, Japan
TEL: +81-3-4316-4820, FAX: +81-3-4316-4823
©FUTABA CORPORATION 2018, 5 (4)
For Park Flyers and Slow Fly models
R2106GF
Thank you for purchasing the R2106GF S-FHSS 6(six)
channel receiver. This model is designed for short range
DSSOLFDWLRQVXFKDVSDUNÀ\HUVDQGVORZÀ\PRGHOV
The R2106GF is compatible with the S-FHSS/FHSS transmitters as shown below.
Futaba T8J-2.4GHz,T6J-2.4GHz,T4YF-2.4GHz
Connectors
1: CH1 servo
2: CH2 servo
3: CH3 servo/ESC connector
4: CH4 servo
5: CH5 servo
6: CH6 servo/battery
Link Button
Antenna
LED
Compliance Information State-
ment (for U.S.A.)
This device, trade name Futaba Corporation of America,
model number R2106GF, complies with part15 of the
FCC Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesiredoperation.
The responsible party of this device compliance is:
FUTABA Corporation of America
2681 Wall Triana Hwy Huntsville, AL 35824, U.S.A.
Phone:1-256-461-9399 FAX:1-256-461-1059
E-mail: [email protected]
5*)6SHFLÀFD-
tions
•
S-FHSS/FHSS system (Auto
detection)
•
Operating voltage(Typ.): 4.8V-
7.4V
• F/S and Battery F/S function
The operation channels differ
according to the transmitter
used. However,Battery F/
S doesn't function when it is
used with FHSS and F/S be-
comes only CH2.
• Battery F/S voltage: 3.8V
• Size: 21.5x38.8x10.7mm
(0.85x1.53x0.42in.)
• Weight: 4.5g (0.16oz.)
WARNING
Do not fold or cut the receiver an-
tenna as it cause shorter range.
Do not apply any excessive force to
the antenna as it may damage the
wire.
The receiver antenna's location must
be away from metal objects such as
servo wiring, motor wiring, or batteries at
least half inch as it keeps better receiving
result.
Never remove the case to avoid the
unexpected malfunction.
The connectors are covered with the
case but the material of the case is
relatively soft as it may cause the reverse
connection thus please pay great attention
when connect a battery or an ESC to keep
the correct polarity. Otherwise the receiver
may break down or the wire may burn out.
Keep away from conductive material
to avoid the short circuit.
Link Switch
Press and hold two(2) seconds to re-
link the transmitter's ID.
* Place the transmitter within 2 ft. (60cm)
to re-link.)
Range Check the Radio
Please follow the transmitter's
instruction manual and check if the
range is over 10 paces.
LED Indication
Green Red Status
Off Solid No signal reception
Solid Off Receiving signals
Blink Off Receiving signals but ID is unmatched
Alternate blink Unrecoverable failure (Memory etc.)
Usage Precautions
This model is designed for short range application such as parkflight or indoor use air-
crafts. Please read the usage condition shown below.
• Do not use it for a middle or large scale model.
• Please be sure that the ESC's regulated output for receiver has enough capacity to
sustain the entire operating condition of your servos, battery, and motor. Never use dry
cell batteris for the receiver as this may cause difficulties with the receiver's operation.
• After the linking is done, please cycle receiver power and check if the receiver to be
linked is really under the control by the transmitter to be linked.
• Please do not perform the linking procedure with motor's main wire is connected as it
may result in serious injury.
• Futaba S-FHSS/FHSS system does not work with current Futaba FASST system. Fu-
taba FASST system and S-FHSS/FHSS system are not compatible each other.
Black Red White
Receiver
bottom side
1M23N17446
  • Page 1 1

Futaba R2106GF Manuel utilisateur

Futaba
Marque
Futaba
Modèle
R2106GF
Catégorie
Antennes réseau
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents