Falmec FPERO30U5SS Mode d'emploi

Ed. 2008

Cod. 110030249 - UNDER CABINET HOOD

INSTRUCTIONS BOOKLET

LIVRET D’INSTRUCTIONS

MANUAL DE INSTRUCCIONES

Dear Sir/Madam, congratulations!

You have purchased a prestigious range hood of guaranteed quality. For best results, we

suggest that you carefully follow the operating and maintenance instructions provided

in this booklet; in addition, to order spare charcoal filters, use the special coupon on the

cover.

Chère Madame/Cher Monsieur, félicitations!

Vous venez d’acheter une hotte haut de gamme. Pour en tirer les performances les

meilleures veuillez lire avec attention le mode d’emploi et la maintenance que vous

trouvez dans ce manuel ; pour commander les filtres de rechange au carbone actif

veuillez vous servir du coupon annexé à la couverture.

Enhorabuena Señora/Señor!

Ha comprado una campana extractora de prestigio y calidad segura. Para que pueda

obtener las mejores prestaciones, le sugerimos seguir con atención las instrucciones

contenidas en este manual para el uso y el mantenimiento. Para pedir los filtros de

recambio de carbón activo, utilice el cupón adjunto a la cubierta.

Product code

ASNET30U4SS

ASROM30U4SS

ARPLU30U4SS

ASALB30U4SS

ASERO30U5SS

ASNET36U4SS

ASROM36U4SS

ARPLU36U4SS

ASALB36U4SS

ASERO36U5SS

1

29 13/16" - 35 7/8" 18 7/8"

12"

1 9/16"

6 11/16"

7 7/8"

12"

18 7/8"

3 11/16"

4 7/8

"

ALBA 760/912

2

29 13/16"

- 35 7/8"

5 1/8"

5 15/16"

21 1/16"

10 1/4"

2 3/8"

12"

EROS 760/912

3

29 13/16"

- 35 7/8"

19 11/16"

6 11/16"

2 3/8"

7 13/16"

12"

4 7/8"

3 11/16"

15 3/4"

NETTUNO 760/912

4

29 13/16"

- 35 7/8"

3 11/16"

4 7/8"

6 11/16"

7 7/8"

19 11/16"

12"

2 3/8"

PLUTONE 760/912

5

29 13/16"

- 35 7/8"

26" - 32 1/16"

19 11/16"

6 11/16"

7 13/16"

12"

2 3/8"

4 7/8"

3 11/16"

ROMBO 760/912

6

650 mm

(25,6”)

OUTSIDE DISCHARGE HOOD

Cabinet

Hood

Fig. C

650 mm

(25,6”)

RECIRCULATING HOOD

Cabinet

Recirculating kit

Hood

7

A

1

B

F

B

2

A

B

Fig. O1

INSTALLING THE INTERNAL RECIRCULATING HOOD

INSTRUCTION DE MONTAGE POUR HOTTE À RECYCLAGE

INTÉRIEUR

INSTRUCCIONES DE MONTAJE PARA CAMPANA CON

RECIRCULACIÓN INTERIOR

8

Fig. O2

INSTALLING THE EXTRACTION HOOD

INSTRUCTION DE MONTAGE POUR HOTTE ASPIRANTE

INSTRUCCIONES CAMPANA EXTRACCIÓN

Air output arranged

Préparation évacuation d’air

Salida de aire predispuesta

Standard output

Sortie standard

Salida estándar

BO02

BO01

A

Rectangular back output

Sortie arrière rectangulaire

Salida posterior rectangular

1

3

4

2

B

BO02

BO01

9

1

2

A

Rectangular upper output

Sortie supérieure rectangulaire

Salida superior rectangular

1

3

4

2

C

GB

INSTRUCTIONS BOOKLET

WARNINGS

A

This instruction booklet must be kept together with the appliance for future

reference. If the appliance is sold or consigned to other parties, check that

the booklet is supplied with it, to ensure that the new user has the correct

information on the operation of the range hood and is aware of the warnings.

These warnings have been provided for the your safety and the safety of oth-

ers. As a result, please read them carefully before installing and operating the

appliance.

This appliance is not intended for use by young children or infirm persons un-

less they have been adequately supervised by a responsible person to ensure

that they can use the appliance safely. Young children should be supervised to

ensure they do not play with the appliance.

The appliance must be installed by qualified personnel, in accordance with

national and local safety regulations the standards in force. If the supply cord

is damaged, it must be re-placed by the manufacturer, its service agent or

similarly qualified persons in order to avoid a hazard. Any modifications that

may be required to the electrical system for the installation of the range hood

must only be made by qualified electricians.

It is dangerous to modify or attempt to modify the characteristics of this sys-

tem. In the event of malfunctions or if repairs are required to the appliance,

do not attempt to solve the problems directly.

Repairs performed by unqualified persons may cause damage. For all repair

and other work on the appliance, contact an authorised service/spare parts

centre.

Always check that all the electrical parts (lights, exhaust device), are off when

the appliance is not being used. Read the entire instruction booklet before

performing any operations on the range hood.

The manufacturer can not be held responsible for unauthorized work. Ensure

that power to the appliance is OFF while installation or repair work is per-

formed.

Verify that the voltage, load and circuit rating information found on the data

plate (located behind the grease filter), match the household electrical supply

before installing the hood.

The range hood must only be used for the exhaust of cooking fumes in home

kitchens. The manufacturer disclaims all liability for any other use of the ap-

pliance.

The maximum weight of any object placed above the hood, or hung to it (if

possible) must not exceed 1,5 kilos. After installing the stainless steel hood,

clean it in order to remove any residue of the protective glue, and stains of

grease or oil. The manufacturer recommends its cleaning cloth available for

purchase. The manufacturer accepts no liability in case of damage caused by

the use of different detergent types.

10

TECHNICAL SPECIFICATIONS

B

The technical data pertaining to the electric appliance The technical specifica-

tions of the appliance are shown on the rating plates located inside the range

hood.

INSTALLATION

C

(Section reserved for qualified installers of the range hood)

Minimum distance: distance between the main top of the cooking appliance

and the bottom-most section of the hood. When the hood is positioned above

a gas appliance this minimum distance must be at least 65 cm (25,6“) (see

fig. C) or more importantly, check the distances specified for the gas cooking

appliance.

In the outside exhaust version, the diameter of the entire duct run must be no

smaller than the range hood connection.

In the horizontal duct run, the duct must slope slightly (around 10%) upwards,

so as to better ventilate the air outside of the room.

Avoid using angled pipes, make sure that the pipes are at least of the mini-

mum length.

Comply with the current regulations on air discharge into the atmosphere.

If a boiler, stove, fireplace, etc. that uses gas or other fuels is being used at

the same time, make sure the room where the fumes are extracted is well

ventilated, in compliance with the current regulations.

Mounting instruction: see section “O” of the booklet.

ELECTRICAL CONNECTIONS

D

(Section reserved for qualified installers)

WARNING!

Before doing any work inside the range hood, disconnect the appliance from

the mains power supply.

Check that the wires inside the range hood are not disconnected or cut; if this

is the case, contact your nearest service centre. The electrical connections

must be performed by qualified personnel.

The connections must be performed in compliance with the legal standards

in force. Check that the receptacle and wiring are able to support the load of

the appliance (see the technical specifications in point B).

THIS APPLIANCE MUST BE GROUNDED.

Important:

The hood comes equipped with a 5 ft(1.5 m) power cord with a NEMA 5-15

molded plug for connection to a 120 VAC, 60 Hz, 15 A power outlet. This outlet

must be located in the duct cover area above the hood.

Some types of appliance are supplied with a cable without plug; in this case,

“standardised” or a junction box must be used, keeping in mind that:

- the yellow/green wire must be used for the earth,

- the blue/white wire must be used for the neutral,

11

12

- the brown/black wire must be used for the phase; the cable must not come

into contact with hot parts (over 75°C).

- fit a plug that is suitable for the load to the power cable, and connect it to a

suitable power outlet.

If local codes permit, the power cord may be removed and the hood may

be connected to a hard wired electrical connection. If there is any question

concerning the electrical connection of this appliance to your power supply,

please consult a licensed electrician.

For appliances that come supplied with cable and plug please ensure they are

plugged into a circuit suitable for this appliance.

Please refer to a qualifed person. (See technical specifications in point B).

The manufacturer declines all liability if the safety standards are not ob-

served.

E

RANGE HOOD WITH OUTSIDE

DISCHARGE (exhaust)

In this application, the fumes and steam from the kitchen are vented outside

through an exhaust duct.

The exhaust conveyor that protrudes from the upper part of the range hood

must be connected to a duct that carries the fumes and steam outside. In this

application, the charcoal filters, if fitted, should be removed; to do this, see the

instructions in point F. There must be adequate ventilation of the room when

the range hood is used at the same time as appliances burning gas or other

fuels, according to the standard.

Deviation for Germany:

When the range hood and appliances supplied with energy other than elec-

tricity are simultaneously in operation, the negative pressure in the room

must not exceed 4 Pa (4x10 E-5 bar).

F

RECIRCULATING RANGE

HOOD (with filter)

In this application, the air passes through charcoal filters for purification, and

is then recirculated back into the kitchen.

Check that the charcoal filters are fitted to the motor, and if not, install them

as described in the instructions in point H.

If the hood is of filtering type, remove the non-return valve fitted at the mo-

tor’s outlet.

For maximum efficiency, the third speed should be used when there are

strong odours or a lot of steam, the second speed in normal conditions, and

the first speed for keeping the air clean with minimum energy consumption.

The range hood should be switched on when starting to cook, and left on

until the odours disappear.

13

G

OPERATION

1. TWO BUTTON CONTROL PANEL (Nettuno, Plutone)

LIGHT - Switch A

Position 0: the light is off.

Position 1: the light is on.

SPEED - Switch B

This is used to start and set the speed of the motor, from 1 to 3, or with

continuous speed variator, depending on the version.

LIGHT - C

Motor operation indicator light.

2. ELECTRONIC CONTROL PANEL (Alba, Eros, Rombo)

Light pushbutton

• ON: light on (the pushbutton is lit);

• OFF: light off;

Pushbutton -

Press to reduce motor speed

Speed 1, 2 and 3 are indicated by the number of LEDs that light up (exclud-

ing the light and the timer LEDs).

Pushbutton +

Press to increase motor speed. Speed 1, 2 and 3 are indicated by the

number of LEDs that light up (excluding the light and the timer LEDs).

(In the 4-speed version the pushbutton + blinks. The fourth speed remains

on for a set duration of time. After 15 minutes the motor returns to the

third speed).

Mode pushbutton

Function: it turns hood motor on and off.

The function “desired speed” enables to start the motor at the speed that

was selected before the hood was last turned off.

Optional: version with remote control (some versions only).

WARNING:

Install the hood away from sources of electromagnetic waves, as these

could affect the correct operation of the electronic system.

Maximum operating distance: 5 metres. The maximum operating distance

could be less than 5 metres in case of electromagnetic interference by

other equipment.

Light pushbutton on remote control: light on/off.

– and + pushbutton: increase/decrease speed (to start the motor press

either the + or the – pushbutton).

14

Timer pushbutton: see instructions below.

Instructions for changing the code (only in case of malfunctions caused by

interferences):

Disconnect the hood from the power supply

Remove the cover of the remote control, change the code with the levers.

Connect the hood to the power supply and make sure the lights and the

motors are off.

Press the timer pushbutton for 2 seconds. When the red LED of the control

panel lights up press any of the buttons on the control panel.

Timer and ‘filter clogged’ alarm pushbutton

• This function allows the automatic turning off of the hood after running

for 15 minutes at the speed previously set (the pushbutton shows a flicker-

ing light).

• After about 30 hours of running the pushbutton indicates the need for

washing the metal filters (the pushbutton shows a solid red light). To dis-

able the alarm press the pushbutton for a few seconds until the red light

turns off. Then turn the hood off and on again to check that the alarm has

disappeared.

FILTERS REMOVING AND REPLACING’S INSTRUCTIONS

H

1. METAL FILTERS

To remove the metal grease-trapping filter, simply pull the handle A until

releasing it from the front guide; then tilt it slightly downwards, and slide

it out of the rear guide. To reposition the filter, repeat the operation in the

reverse order.

A

2. CHARCOAL FILTERS

To replace the charcoal filters, proceed as follows:

- remove the metal filters as described above.

To install the new ﬁ lters see the pictures below.

To order new filters, use the coupon enclosed with this booklet or provided

by the distributor.

15

UNDER CABINET: ALBA, PLUTONE, ROMBO, NETTUNO UNDER CABINET: EROS

LIGHTING ASSEMBLY AND REPLACEMENT

I

1. SPOTLIGHT

To replace the lamp (“Round halogen light”):

a) Make sure the appliance is disconnected from the mains power supply.

b)

Remove, by levering with a screwdriver, the support ring A for the cover glass.

c) Remove the cover glass B to access the light compartment.

d)

Replace the lamp with the same type (halogen, max 20 W, 12 Volt, G4 fitting).

e) Replace the glass cover B and fasten it using the special ring A.

Round halogen light

How to replace a square halogen light:

a) Check that the equipment is disconnected from the power supply.

b) Open the panel completely till 90° (see figure) pressing the PUSH button

c) Replace the lamp with a similar one (halogen, max 20 W, 12 Volt, G4 con-

nection).

d) Close the panel. If the panel does not close correctly repeat the operation

at point b.

Square halogen light

16

2. FLUORESCENT TUBE

(Section reserved for qualified installers)

Replacing the fluorescent tube:

a) Disconnect the device from the mains;

b) Unscrew the fixing screws and remove the bottom panel;

c) Remove the fluorescent tube, by rotating through 90°, and replace it with

one of similar features (8W-13W-21W-28W according with the model);

d) Reconnect the device to the mains.

MAINTENANCE AND CLEANING

L

Constant maintenance ensures the correct operation and efficiency of the ap-

pliance over time. Special attention should be paid to the metal grease-trap-

ping filters and the charcoal filters. Frequent cleaning of the filters and their

supports will ensure that fats and grease do not accumulate on the range

hood, with the consequent risk of fire.

1. METAL GREASE-TRAPPING FILTERS

These trap the fat and grease particles suspended in the air, and therefore

should be washed every month in hot water and detergent, without bend-

ing them. Wait until they are completely dry before repositioning them.

To remove and replace these filters, see the instructions in point H1. This

operation should be performed at regular intervals.

2. CHARCOAL FILTERS

These trap the odours present in the stream of air that passes through

them. The air is purified by passing a number of times through the filters

and being recirculated into the kitchen. The charcoal filters cannot be

cleaned, and should be replaced on average every 3-4 months (according

to use). To replace the charcoal filters, see the instructions in point H2.

3. CLEANING THE OUTSIDE OF THE APPLIANCE

The ouside of the range hhod should be cleaned using a damp cloth and

neutral liquid detergent or denatured alcohol.

In case of fingerprint-less finish (fasteel) clean only with water and neutral

soap using clean with a soft cloth, rinse and wipe dry thoroughly. Do not

use products that contain abrasive substances, rough cloths or cloths spe-

cifically designed for cleaning steel. Using abrasive substances or rough

cloths will inevitably damage the finish of steel. The steel surface will be

irrevocably damaged if the instructions above are not complied with. Keep

these instructions together with the instructions for use of your hood.

The manufacturer accepts no liability for any damage caused by non-com-

pliance with the instructions above.

4. CLEANING THE INSIDE OF THE APPLIANCE

The electrical parts or parts of the motor assembly inside the range hood

must not be cleaned using liquids or solvents.

Do not use abrasive products.

All the above operations must be performed after having disconnected the

appliance from the mains power supply.

17

SAFETY WARNINGS

M

The electrical system features an earth connection in compliance with in-

ternational safety standards; furthermore, it is compliant with the European

standard for electromagnetic compatibility.

Do not connect the appliance to flues (from boilers, fireplaces, etc.). Make

sure the mains voltage corresponds to the values on the rating plate located

inside the range hood. The minimum safety distance between the cooktop and

the range hood must be at least 65 cm (25,6”).

Never cook on “open” flames under the range hood.

Check deep-fryers during use: superheated oil may be flammable.

- Ensure there is adequate ventilation of the room when the rangehood is

used at the same time as appliances burning gas or other fuels.

- Do not flambe under the rangehood

- The exhaust air must not be discharged into a flue which is used for exhaust-

ing fumes from appliances burning gas or other fuels.

- Ensure that all regulations concerning the discharge of exhaust air have

been fulfilled before you use the appliance.

Before performing any cleaning or maintenance operations, disconnect the ap-

pliance by unplugging it or using the main switch. The manufacturer disclaims

all liability for any damage that may be directly or indirectly caused to people,

things and animals due to the failure to follow all the instructions provided in

this booklet and above all the warnings relating to the installation, operation

and maintenance of the appliance.

WARRANTY

N

The new equipment is covered by warranty.

The warranty conditions are provided by the distributor.

The manufacturer is not liable for any inaccuracies in this booklet resulting

from printing or transcription errors. The manufacturer reserves the right to

modify its products as it considers necessary or in the interests of the user,

without compromising their essential safety and operating characteristics.

O

MOUNTING INSTRUCTIONS, RANGE

HOODS WITH BOX

INSTALLING THE INTERNAL RECIRCULATING HOOD (fig. O1)

Step 1

- Mount the air recirculation kit (specific for the hood to be installed) onto the

cabinet, using the screws provided (A).

- Check that the back output be closed by buffer BO1 and BO2.

Step 2

- Remove the hood’s metal filters as described in section H1.

- Install the carbon filters (F) as described in section H2.

- Mount the hood onto the recirculation kit that was previously installed, using

18

the screws provided (B).

- Connect the hood’s electric system, in compliance with current norms.

- Put the metal filters back in place.

INSTALLING THE EXTRACTION HOOD (fig. O2)

Step 1

- Decide how the fumes are to be expelled (from the top or from the back).

- See instructions for the configuration A, B or C.

Step 2

- Remove the hood’s metal filters as described in section H1.

- Mount the hood onto the cabinet with the screws provided (A).

- Connect the hood’s electric system, in compliance with current norms.

- Put the metal filters back in place.

La page est en cours de chargement...

Falmec FPERO30U5SS Mode d'emploi

Ce manuel convient également à

Falmec FPERO30U5SS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents