Norcold 1210 Ultraline Guide d'installation
- Catégorie
- Cheminées
- Taper
- Guide d'installation
NORCOLD, Inc.
P.O. Box 4248
Sidney, OH 45365-4248
Part No. 635493E (12/23/2019)
English
Installation Manual
for the 121X series of RV Refrigerators
The letter “X”, in the model numbers above, stands for a letter or numeral which means a
refrigerator option.
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to this manual. For assistance
or additional information, contact a qualied installer, service agency, or
the gas supplier.
FIRE OR EXPLOSION HAZARD
If you smell gas:
1. Open Windows
2. Do not attempt to light appliance.
3. Do not touch electrical switches.
4. Extinguish any open ame
5. Shut o fuel supply.
6. Evacuate immediately and call emergency services.
Failure to follow these instructions could result in re or explosion, which could cause
property damage, personal injury, or death.
DO NOT install this refrigerator in below deck marine applications. Do not install this refrigerator in a
xed indoor cabin or other dwelling applications. This refrigerator must use only NORCOLD designed and
approved outside air intake and exhaust ventilation for correct and safe operation. Any other ventilation
could cause lethal combustion exhaust fumes and/or explosive propane gas fumes to be in the living area
and/or to be below deck.
FOR YOUR SAFETY
Do not store or use gasoline or other ammable vapors and liquid in the
vicinity of this or any other appliance.
Norcold Customer Support Dept.
Telephone: 800-543-1219
Fax: 734-769-2332
Web Site: www.norcold.com
WARNING
!
WARNING
!
WARNING
!
Installation Manual 2
Table of Contents
Safety Awareness
Safety Awareness ........................................................................................................................................................................................ 2
Safety Instructions ....................................................................................................................................................................................... 3
Certication and Code Requirements.......................................................................................................................................................... 3
Ventilation Requirements............................................................................................................................................................................. 4
Key Refrigerator Dimensions....................................................................................................................................................................... 5
Assemble the Enclosure for the Refrigerator............................................................................................................................................... 6
Install the Lower Intake Vent ....................................................................................................................................................................... 6
Optional Installation ..................................................................................................................................................................................... 7
Install the Upper Roof Exhaust Vent............................................................................................................................................................ 8
Install the Baes for an Upper Roof Exhaust Vent ..................................................................................................................................... 8
Vertical enclosures ............................................................................................................................................................................... 8
Oset vertical enclosures ................................................................................................................................................................... 10
Install an Upper Side-Wall Exhaust Vent ................................................................................................................................................... 12
Install the Baes for an Upper Side-Wall Exhaust Vent ............................................................................................................................ 12
Install an Air Deector (optional)................................................................................................................................................................ 14
Install Decorative Door Panels (non-metal door models) .......................................................................................................................... 14
Install the Refrigerator ............................................................................................................................................................................... 15
Connect the Electrical Components .......................................................................................................................................................... 17
Connect the 120 volts AC supply ....................................................................................................................................................... 17
Connect the 12 volts DC supply ......................................................................................................................................................... 17
Connect the Low Ambient Heater (optional) .............................................................................................................................................. 18
Connect the Propane Gas Components.................................................................................................................................................... 19
Connect the propane gas supply system .................................................................................................................................................. 19
Examine the propane gas supply system for leaks ................................................................................................................................... 19
Connect the Ice Maker (optional) .............................................................................................................................................................. 20
Connect the water supply line ................................................................................................................................................................... 20
Ignition and Start Up .................................................................................................................................................................................. 21
Set the controls to automatic mode operation .................................................................................................................................... 21
Set the controls to manual mode operation........................................................................................................................................ 22
Do a test of the gas safety valve .............................................................................................................................................................. 22
Shut down.................................................................................................................................................................................................. 22
Fault Codes ............................................................................................................................................................................................... 23
Read this manual carefully and understand the contents before you install the refrigerator.
Be aware of possible safety hazards when you see the safety alert symbol on the refrigerator and in this manual. A signal word follows
the safety alert symbol and identies the danger of the hazard. Carefully read the descriptions of these signal words to fully know their
meanings. They are for your safety.
This signal word means a hazard, which if ignored, can cause dangerous personal injury, death, or much
property damage.
This signal word means a hazard, which if ignored, can cause small personal injury or much property
damage.
CAUTION
!
WARNING
!
Installation Manual 3
Certication and Code Requirements
Safety Instructions
- This refrigerator is not approved for use as a free standing refrigerator. It is equipped for the use of propane gas only
and can not be changed to use any other fuels (natural gas, butane, etc.).
- Incorrect installation, adjustment, alteration, or maintenance of this refrigerator can cause personal injury, property
damage, or both.
- Obey the instructions in this manual to install intake and exhaust vents.
- Do not install the refrigerator directly on carpet. Put the refrigerator on a metal or wood panel that extends the full
width and depth of the refrigerator.
- Do not allow anything to touch the refrigerator cooling system.
- Propane gas can ignite and cause an explosion that can result in property damage, personal injury, or death. Do not
smoke or create sparks. Do not use an open ame to examine the propane gas supply line for leaks. Always use two
wrenches to tighten or loosen the propane gas supply line connections.
- Make sure the electrical installation obeys all applicable codes. See “Certication and Code Requirements” section.
- Do not bypass or change the refrigerator’s electrical components or features.
- Do not spray liquids near electrical outlets, connections, or the refrigerator components. Many liquids are electrically
conductive and can cause a shock hazard, electrical shorts, and in some cases re.
- The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system.
- The cooling system contains sodium chromate. The breathing of certain chromium compounds can cause cancer. The
cooling system contents can cause severe skin and eye burns, and can ignite and burn with an intense ame. Do not
bend, drop, weld, move, drill, puncture, or hit the cooling system.
- The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the
refrigerator, use caution and wear cut resistant gloves.
- Make sure that the refrigerator is stored in a location so that it is not exposed to the elements of the weather.
This refrigerator is certied by CSA International as meeting the
latest edition of ANSI Z21.19 / CSA 1.4 standards for installation in
mobile homes or recreational vehicles.
The installation must obey these standards and this “Installation
Manual” for the NORCOLD limited warranty to be in eect.
Installation must conform with the following as applicable:
CAUTION
!
WARNING
!
Art01290
Installation Manual 4
Ventilation Requirements
The completed installation must:
- Make sure there is sucient intake of fresh air for combustion.
- Make sure the living space is completely isolated from the combustion system of the refrigerator.
- Make sure there is complete and unrestricted ventilation of the ue exhaust which, in gas mode, can produce carbon
monoxide. The breathing of carbon monoxide fumes can cause dizziness, nausea, or in extreme cases, death.
- Make sure the refrigerator is completely isolated from its heat generating components through the correct use of
baes and panel construction.
Certied installation needs one lower intake vent and one upper exhaust vent. Install the vents exactly as written in this manual. Any
other installation method voids both the certication and the factory warranty of the refrigerator.
The bottom of the opening for the lower intake vent, which is also the service access door, must be even with or immediately below the
oor level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.
CSA International certication allows the refrigerator to have zero (0) inch minimum clearance at the sides, rear, top, and bottom.
While there are no maximum clearances specied for certication, the following maximum clearances are necessary for correct
refrigerator performance:
Bottom 0 inch min. 0 inch max.
Each Side 0 inch min. 1/2 inch max.
Top 0 inch min. 1/4 inch max.
Rear 0 inch min. 1 inch max.
These clearances plus the lower and upper vents allow the natural air draft that is necessary for good refrigeration. Cooler air comes in
through the lower vent, goes up around the refrigerator coils where it removes the excess heat from the refrigerator components, and
goes out through the upper vent.
The refrigerator also has two thermostat controlled fans to move air across the cooling system. These fans turn on when the condenser
n temperature at the thermostat is about 130° F or higher and only when the refrigerator controls are on. These fans turn o when the
condenser n temperature at the thermostat is about 115° F or less. Even with these fans, if the air ow is blocked or decreased, the
refrigerator will not cool correctly.
Each NORCOLD model is certied by CSA International for correct ventilation. Install only the certied vents that are listed in this
manual.
In the United States and Canada:
- Local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1/NFPA 54, the Natural Gas and Propane
installation Code, CSA B149.1, ANSI A119.2 Recreational Vehicles Code, and CSA Z240 RV Series, Recreational Vehicles.
- A manufactured home (mobile home) installation must conform with the Manufactured Home Construction and Safety Standard,
Title 24 CFR, Part 3280 [formerly the Federal Standard for Mobile Home Construction and Safety, Title 24 (part 280), and the
current CSA Z240.4, Gas-equipped Recreational Vehicles and Mobile Housing.
- If an external power source is utilized, the appliance, when installed, must be electrically grounded in accordance with local codes
or, in the absence of local codes, the National Electrical code, and ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2.
Parts 1 and 2.
All propane gas supply piping and ttings must obey local, state, and national codes about type and size. These components must also
obey the current NFPA 1192 section 2-4, and in Canada with the current CAN 1-6.10 Standard.
WARNING
!
Installation Manual 5
Key Refrigerator Dimensions
These key refrigerator dimensions are for your reference as necessary (See Art01734).
Refrigerator cabinet width w/o trim - 32.4 in. ....................... 1
Refrigerator width overall w/ trim - 35.0 in. .......................... 2
Refrigerator cabinet to side trim - 1.30 in. ...........................3
Refrigerator cabinet height w/o trim - 63.2 in.......................4
Refrigerator height overall w/ trim - 65.1 in..........................5
Refrigerator cabinet to top/bottom trim - 0.90 in. ................. 6
Enclosure wall to hinges - 1.92 in. .......................................7
Refrigerator cabinet to center of handles - 40.5 in. .............8
Enclosure wall to door (w/dispenser) - 4.47 in.................123
Art01734
2
1
8
7
3
5
4
6
123
Installation Manual 6
Assemble the Enclosure for the Refrigerator
Install the Lower Intake Vent
Install the lower intake vent (See Art01597):
The lower intake vent is also the service access opening for the components on the rear of the refrigerator.
Make sure the bottom of the opening of the lower intake vent is even with or immediately below the oor
level. This allows any leaking propane gas to escape to the outside and not to collect at oor level.
- Make sure the bottom of the opening of the lower intake vent [9] is even with or immediately below the oor level.
- Make sure that the opening for the lower intake vent is between 1/2 inch and 1 inch from the burner side of the refrigerator
enclosure.
1. Make sure the enclosure shelf is solid and level. The enclosure shelf must be:
- a metal or a wood panel and extend the full width and depth of the enclosure.
- able to support the weight of the refrigerator and its contents.
- level to maintain door alignment.
2. Make sure there are no adjacent heat sources such as a furnace vent, a hot water heater vent, etc.
3. Make sure the enclosure is 63.25 - 63.38 inches high x 32.69 - 32.82 inches wide x 24 inches deep.
Measure the enclosure depth [174] from the interior face of the enclosure to the inside
of the rear wall (See art01763).
4. If there is more than 1/2 inch between either side of the refrigerator and the inside of the enclosure:
- Fill the space with berglass (batt-type) insulation or add a bae to eliminate the clearance.
- The rear of the batt-type insulation must be between 18 -19 inches from the face of the
enclosure.
- Securely attach the batt-type insulation to the enclosure, so that it remains in this position during refrigerator installation, if it
becomes wet, and in windy conditions.
5. The enclosure face must be perpendicular to the enclosure shelf to provide a combustion seal.
6. The cutout opening must be square and perpendicular to the enclosure shelf to maintain door alignment.
7. Using the following chart, decide which vents and rough opening (RO) sizes to use:
Certied Vent P/N RO Height RO Width
Upper Roof Exhaust Cap 622293 N/A N/A
625240 N/A N/A
Upper Roof Exhaust Vent 616319 24 in. 5 1/4 in.
625161 24 in. 5 1/4 in.
Upper Plastic Exhaust & Lower Intake 621156 / 637615 13 3/4 in. + 1/8-0in 21 1/2 in.+1/8-0in.
Lower Metal Corner Intake 616010 9 3/4 in. 9 3/8 in.
The RO must be square. Diagonal measurements of the RO should be within 1/16in. The vent should be centered in the RO width.
Art01763
174
NOTICE
NOTICE
WARNING
!
Installation Manual 7
You can change enclosures that were made for Norcold model N8XX refrigerators so that you can put Norcold model 121X refrigerators
into them.
To change the Norcold model N8XX refrigerator enclosure [130] into the Norcold model 121X refrigerator enclosure [131] (See
Art01597):
- Increase the height of the enclosure by 3 3/8 inches [132].
- Increase the width of the enclosure by 8 13/16 inches [133].
- Make sure to add the additional width to the left side of the enclosure (as looking at the rear of the refrigerator).
Install the necessary baes only as written in the “Install the Upper and Lower Vents” section of this manual.
The locations of the 12 VDC supply, the 120 VAC supply, and the propane gas supply line do not change.
Optional Installation
12
Art01597
12
11
9
130
131
132
N8XX
120X
133
Installation Manual 8
1. Install the upper roof exhaust vent.
Make sure that no sawdust, insulation, or other construction
debris is on the refrigerator or in the enclosure. Debris can cause
a combustion hazard and prevent the refrigerator from operating
correctly.
Tighten the screws of the upper roof exhaust cap to 10 inch-pounds max.
Also make sure that the air ow around the upper roof exhaust cap is not
blocked or decreased by other roof mounted features such as a luggage
carrier, an air conditioner, a solar panel, etc.
2. Align the upper roof exhaust vent above the lower intake exhaust vent (See Art01597):
3. Determine the type of enclosure in a vehicle using an upper roof exhaust vent (See
Art01756):
- If the distance from the face of the enclosure to the inboard edge of the roof exhaust
vent opening [169] is more than 17 1/2 inches, install the roof exhaust vent [12] directly
above the condenser [11] of the refrigerator as a vertical enclosure.
- If the distance from the face of the enclosure to the inboard edge of the roof exhaust vent opening [169] is 17 1/2 inches or less,
install the roof exhaust vent [12] inboard from the condenser [11] of the refrigerator as an oset vertical enclosure.
Install an Upper Roof Exhaust Vent
Install the Baes for an Upper Roof Exhaust Vent
Make sure that all horizontal baes are the full width of the inside of the
enclosure and are in the correct location. If the baes are not the full
width of the enclosure or incorrectly located, poor cooling performance
can result.
Vertical enclosures:
If the enclosure depth is 24 inches or more and less than 25 inches (See Art01780):
- Install a top bae [13].
- Make sure there is less than 1/4 inch clearance between the bae and the top of the
refrigerator.
Art01756
11
12
169
Art01780
13
15
CAUTION
!
CAUTION
!
NOTICE
Installation Manual 9
If the enclosure depth is 25 inches or more and less than 26 inches (See Art01781):
- Install a top bae [13].
- Make sure that the top bae is less than 1/4 inch [15] from the top of the
refrigerator.
- Install a condenser bae [16] at the lowest edge of the condenser of the refrigerator.
- Make sure that the condenser bae is 1 inch or less [19] from the condenser.
- Install an absorber bae [171] 18 inches to 18 1/2 inches above the bottom of the
enclosure [17] (4 1/4 inches to 4 3/4 inches above the top of the lower intake vent
opening) [18] .
- Make sure that the absorber bae is 1 inch or less [19] from the absorber.
If the enclosure depth is 26 inches or more (See Art01782):
- Install a top bae [13].
- Make sure that the top bae is less than 1/4 inch [15] from the top of the
refrigerator.
- Install a wood or an aluminum or galvanized sheet solid box bae [21] in the rear of
the enclosure.
- Make sure that the bottom of the solid box bae is 18 inches to 18 1/2 inches
above the bottom of the enclosure [17] (4 1/4 inches to 4 3/4 inches above the
top of the lower intake vent opening) [18] .
- Make sure that the back of the solid box bae is perpendicular to the bottom of
the enclosure.
- Make sure that the back of the solid box bae is against the top of the enclosure.
- Make sure that the solid box bae is one inch or less [19] from the coils [10]
and condenser [11] of the refrigerator.
- Make sure that the solid box bae is the full width of the inside of the
enclosure.
Art01781
15
13
19
16
19
171
18
17
10
11
Art01782
12
19
13
15
21
10
18
9
17
11
Installation Manual 10
Oset vertical enclosures:
If the enclosure depth is 24 inches or more and less than 25 inches (See Art01783):
- Install an angled top bae [172] between the top rear edge of the refrigerator and the
inside edge of the upper exhaust vent opening.
- Make sure that the angled top bae is less than 1/4 inch [15] from the top of the
refrigerator.
- Make sure that the angled top bae is no more than 45° from vertical [20].
- Install an inside corner bae [173] between the outside edge of the upper exhaust
vent opening and either the side wall of the vehicle or the solid box bae (depending
on the vehicle design).
If the enclosure depth is 25 inches or more and less than 26 inches (See Art01784):
- Install an angled top bae [172] between the top rear edge of the refrigerator and the
inside edge of the upper exhaust vent opening.
- Make sure that the angled top bae is less than 1/4 inch [15] from the top of the
refrigerator.
- Make sure that the angled top bae is no more than 45° from vertical [20].
- Install an inside corner bae [173] between the outside edge of the upper exhaust
vent opening and either the side wall of the vehicle or the solid box bae (depending
on the vehicle design).
- Install a condenser bae [16] at the lowest edge of the condenser of the refrigerator.
- Make sure that the condenser bae is 1 inch or less [19] from the condenser.
- Install an absorber bae [171] 18 inches to 18 1/2 inches above the bottom of the
enclosure [17] (4 1/4 inches to 4 3/4 inches above the top of the lower intake vent
opening) [18] .
- Make sure that the absorber bae is 1 inch or less [19] from the absorber.
Art01783
15
20
172
173
Art01784
20
15
172
173
10
16
19
18
17
171
19
11
Installation Manual 11
If the enclosure depth is 26 inches or more (See Art01785):
- Install an angled top bae [172] between the top rear edge of the refrigerator and the
inside edge of the upper exhaust vent opening.
- Make sure that the angled top bae is less than 1/4 inch from the top of the
refrigerator.
- Make sure that the angled top bae is no more than 45° from vertical [20].
- Install an inside corner bae [173] between the outside edge of the upper exhaust
vent opening and either the side wall of the vehicle or the solid box bae (depending
on the vehicle design).
- Install a wood or an aluminum or galvanized sheet solid box bae [21] in the rear of
the enclosure.
- Make sure that the bottom of the solid box bae is 18 inches to 18 1/2 inches
above the bottom of the enclosure [17] (4 1/4 inches to 4 3/4 inches above the top
of the lower intake vent opening) [18] .
- Make sure that the back of the solid box bae is perpendicular to the bottom of
the enclosure.
- Make sure that the back of the solid box bae is either against the top of the
enclosure or against the inside corner bae [173] (depending on the vehicle
design).
- Make sure that the solid box bae is one inch or less from the coils [10] and
condenser [11] of the refrigerator.
- Make sure that the solid box bae is the full width of the inside of the
enclosure.
Art01785
14
20
172
21
18
11
9
17
10
173
9
Installation Manual 12
If the design of the vehicle does not allow you to install a roof exhaust vent, install an upper side-wall
exhaust vent.
The refrigerator is 23.7 in. min. to 24.0 in. max. from the rear of the breaker to the rear of
the condenser [22] and is 57.7 in. min. to 58.0 in. max. from the bottom of the refrigerator
to the bottom of the refrigerator condenser [23] (See Art01600).
Only use an upper side-wall exhaust vent on refrigerator models that are
equipped with a fan. If you use an upper side-wall exhaust vent on a
refrigerator model that is not equipped with a fan, the refrigerator cooling
performance will be poor.
Make sure the refrigerator model is equipped with a fan.
- Install the upper side-wall exhaust vent [24] so that the distance [25] from the bottom of the
enclosure to the top of the rough opening for the upper exhaust vent is at least 63 inches (see
Art01588 and Art01589).
- Align the upper exhaust vent horizontally above the lower intake vent [9].
Install an Upper Side-Wall Exhaust Vent
Install the Baes for an Upper Side-Wall Exhaust Vent
Make sure that all horizontal baes are the full
width of the inside of the enclosure and are in the
correct location. If the baes are not the full width
of the enclosure or incorrectly located, poor cooling
performance can result.
If the enclosure depth is 24 inches or more and less than 26 inches (See
Art01764):
- Install a wood, aluminum or galvanized steel top bae [13] between the
top of the refrigerator and the top of the upper exhaust vent [24].
- Make sure that the top bae is less than 1/4 inch [15] from the top of
the refrigerator and bae overlaps the refrigerator 1 inch or less.
- Make sure that the bae is against the wall of the vehicle at the top
of the upper exhaust vent and less than 1/4 inch above the opening
for the upper exhaust vent.
- Install an aluminum or galvanized steel bent-sheet condenser bae [26].
- Make sure that the bend of the condenser bae is the full width of
the inside of the enclosure.
Art01600
23
22
Art01764
13
25
24
9
26
15
15
CAUTION
!
CAUTION
!
NOTICE
Installation Manual 13
- Make sure that the bend of the condenser bae is
ush with the bottom edge of the door frame of the
upper side-wall exhaust vent.
- Make sure that the top edge of the condenser bae is
1/4 inch or less [15] from the lower rear corner of the
condenser.
If the enclosure depth is 26 inches or more (See Art01787):
- Install a wood, aluminum or galvanized steel top bae [13]
between the top of the refrigerator and the top of the upper
exhaust vent [24].
- Make sure that the top bae is less than 1/4 inch [15]
from the top of the refrigerator and bae overlaps the
refrigerator 1 inch or less.
- Make sure that the bae is against the wall of the
vehicle at the top of the upper exhaust vent and less
than 1/4 inch above the opening for the upper exhaust
vent.
- Install solid box bae [21] between the lower intake vent
and the upper exhaust vent.
- Make the solid box bae either from wood or from an
aluminum or galvanized-steel sheet.
- Make sure that the bottom of the solid box bae is
18 inches to 18 1/2 inches above the bottom of the
enclosure [17] (4 1/4 inches to 4 3/4 inches above the
top of the lower intake vent opening REF) [18].
- Make sure that the back of the solid box bae is
perpendicular to the bottom of the enclosure.
- Make sure that the horizontal top of the solid box bae
is even with the bottom edge of the upper exhaust vent
[24].
- Make sure that the vertical top edge of the solid box bae is 1/2 inch or less [170] below and 1/4 inch or less behind [15] the
lower rear corner of the condenser [11].
Art01787
15
13
15
15
24
21
25
18
17
9
27
170
11
Installation Manual 14
The doors are made to accept decorative panels. The decorative panels
must be 3/16 inch or less in thickness. Install the decorative door panels
in the refrigerator doors before installing the refrigerator in the vehicle.
1. Make two upper door panels that are 16 13/64 inches wide x 18 3/8 inches high:
- Raised panels must be centered on each door and no larger than 15 11/32 inchs
wide x 17 17/32 inches high.
2. Make two lower door panels that are 16 13/64 inches wide x 41 13/64 inches high:
- Raised panels must be centered on each door and no larger than 15 11/32 inchs
wide x 40 11/32 inches high.
3. Install the decorative door panels:
- Pull the panel retainer [37] o of each door [39] (See Art01797).
- Push a decorative door panel [38] into the slots of each door.
- Make sure that each panel retainer is correctly positioned and push the
curved snap [125] of the panel retainer [37] inside of the curved snap [126] of
the door (See Art01794).
Install Decorative Door Panels (non-metal door models)
Install an Air Deector (optional)
If the oor plan has the refrigerator on the rear wall of
the vehicle, obey all of the vent installation as written in
the “Install the Lower and Upper Vents” section of this
manual. Install the roof exhaust vent so that:
- The sloped end of the roof exhaust vent is toward
either side of the vehicle.
- The roof exhaust vent is perpendicular to the air
ow over the vehicle.
Install an air deector on the roof of the vehicle
between the roof exhaust vent and the front of the
vehicle (See Art01767).
- Make sure that the air deector [175] is between
the roof exhaust vent [24] and the front of the
vehicle [179].
- Make sure that the air deector is at least 3 1/2 inches high [176].
- Make sure that the overall width [177] of the air deector is 32 7/8
- Make sure that the distance between the air deector and the roof exhaust vent is between 2 and 3 inches [178].
179
175
24
176
177
178
Art01767
37
125
126
Art01794
NOTICE
Installation Manual 15
When manually (by hand) or mechanically (by hoist , lift truck, etc.) handling
a refrigerator that is not installed in an enclosure, the best method is while the
regerator is in it’s original packaging.
If the refrigerator is not in its original packaging, use the sides, the edges, and/or
the corners of the refrigerator cabinet as the primary load carrying points.
There are two (2) areas of the cooling unit that may be used as handling points
[122] (See Art01754). These handling points may be used only to tilt or to steady
the refrigerator. When tilting the refrigerator, Norcold recommends that you have a
another person hold the refrigerator cabinet.
CAUTION: Do not lift or drag the refrigerator by using
either or both of the two (2) handling points. Damage to the
refrigerator cooling unit can result.
- Put the refrigerator completely into the enclosure:
- Push below the center of the refrigerator.
- Pull using a wire-form tool hooked into mounting holes [121] of the
refrigerator frame (See Art01753).
Make sure the foam combustion seal is not broken,
is completely around the refrigerator mounting anges, and is
between the mounting anges and the wall of the enclosure If
the seal is not complete, exhaust fumes can be present in the
living area of the vehicle. The breathing of exhaust fumes can
cause dizziness, nausea, or in extreme cases, death.
1. Put the refrigerator in position:
Make sure the combustion seal is not broken, is completely around
the refrigerator mounting anges, and is between the mounting
anges and the wall of the enclosure If the seal is not complete,
exhaust fumes can be present in the living area of the vehicle. The
breathing of exhaust fumes can cause dizziness, nausea, or in extreme cases, death.
Be careful when you put the refrigerator into position. The refrigerator has vacuum insulating panels on the top and
sides. If punctured, these panels lose insulation value which decreases the cooling performance of the refrigerator.
It is not necessary to remove the protective packaging from the doors of metal door models to install or operate the
refrigerator.
- Make sure that the ue cap is not pushed down against the top of the ue tube.
- Push the refrigerator into the enclosure so the side trim is approximately one inch from the wall.
Install the Refrigerator
Art01754
122
122
121
Art01753
CAUTION
!
NOTICE
WARNING
!
WARNING
!
Installation Manual 16
2. Make sure that the side trim pieces [127] are in the
correct position (See Art01649 and Art01650):
- Slide both side trim pieces up or down as necessary
so that the ends of the side trim pieces are fully
covered by the upper and lower trim pieces [40 and
128].
- Pull the left hand side trim piece toward the left as
far as it will go so that there is no gap between the
edge of the side trim piece and the upper and lower
trim pieces.
- Pull the right hand side trim piece toward the right as
far as it will go so that there is no gap between the
edge of the side trim piece and the upper and lower
trim pieces.
- Push the refrigerator completely into the enclosure.
3. Install the mounting screws and trim:
- Put the upper trim piece [40] onto the front of the
refrigerator (See Art01649).
- Put the four screws [41] through the mounting ange on the
front of the refrigerator and into the enclosure wall.
- Put a cap plug [129] on each of the screw holes in the
upper trim piece on the front of the refrigerator.
Do not omit the lower trim piece. This
piece is part of the combustion seal.
- Push the lower trim piece [128] onto the front of the refrigerator (See Art01650).
- Put the four screws [41] through the mounting ange on the front of the refrigerator and into the enclosure wall.
- Put a cap plug [129] on each of the screw holes in the lower trim piece on the front of the refrigerator.
- Put two or more screws through the mounting ange on the rear of the refrigerator and into the oor.
4. On metal door models only, you may wish to remove the protective packaging from the doors.
Be careful to not scratch or dent the metal doors. Do not use any abrasive cleaners, chemicals, or scouring pads
because they can damage the ninish of the doors.
Art01649
4041
127
127
129
Art01650
4127
128
129
127
NOTICE
WARNING
!
Installation Manual 17
This refrigerator operates on these electrical sources. Operation out of these limits may damage the refrigerator’s electrical circuit parts
and will void the warranty.
AC Operation 120 volts AC voltage (132 volts max. - 108 volts min.)
12 volts DC control voltage (15.4 volts max. - 10.5 volts min.)
The rear of the refrigerator cooling system has hot surfaces and sharp surfaces that can damage electrical
wiring. Make sure that there is a good clearance between all electrical wiring and the cooling system of the
refrigerator. Position any electrical wiring within the refrigerator enclosure opposite the burner side of the
refrigerator. Do not put any electrical wiring through the roof exhaust vent. Failure to correctly position
electrical wiring can result in electrical shock or re.
Connect the 120 volts AC supply:
Connect the AC power cord(s) only to a grounded three-prong receptacle. Do not remove the round
ground prong from the AC power cord of the refrigerator or the ice maker (optional). Do not use a two
prong adapter or an extension cord with either AC power cord. Operation of the refrigerator without
correct ground can cause dangerous electrical shock or death if you are touching the metal parts of the
refrigerator.
Put the AC power cord(s) into a grounded three-prong receptacle:
- Make sure the receptacle is positioned within easy reach of the lower intake vent.
- Make sure the power cord(s) does not touch the burner cover, the ue pipe, or any hot component that could damage the insulation
of the power cord.
Connect the 12 volts DC supply:
The refrigerator controls operate on 12 VDC power. As the distance from the vehicle battery to the refrigerator increases, the correct
AWG wire size and fuse size also increases. If the wire size is too small for the distance, a voltage drop occurs.
Use a minimum of 18 AWG wire and a maximum 6 Amp fuse. If the wire size is larger than the min. size, use the correct fuse per RVIA
A119.2 standard or local codes.
1. Install a fuse in DC power supply wires between the battery and the refrigerator:
- Put fuse as close to the battery as possible.
2. Connect the DC power supply wires (See Art02242):
- Attach a 1/4 inch Quick Connect terminal to each DC power supply
wire.
Do not use the chassis of the refrigerator or the vehicle
frame as one of the conductors.
- Connect the positive DC power wire [50] to the teminal on the power
board [49] that is marked 12VDC.
- Push the DC ground wire [51] onto the terminal of the power board [49]
that is marked GND.
- Make sure each DC power supply wire is on the correct polarity
terminal.
Connect the Electrical Components
NOTICE
WARNING
!
WARNING
!
Art02242
49
51
50
Installation Manual 18
Connect the Low Ambient Heater (optional)
Connect the low ambient heater wires to the 12 volts DC supply. The
black (+) wire of the low ambient heater is 16 AWG and the brown (-) wire
is 18 AWG.
1. Cut the 12V input (+) wire behind the quick connect [269]; strip both
ends (See Art02316).
2. Solder the wires with the 16AWG black wire [266].
3. Wrap the soldered wires with black electrical tape [268]; BE SURE
there are no exposed strands.
4. Cut the 12V ground wire behind the quick connect [269]; strip both
ends (See Art02317).
5. Solder the wires with the 18AWG wire [267].
6. Wrap the soldered wires with black electrical tape [268] ; BE SURE there
are no exposed strands.
7. Connect 12V supply to the input wires.
This kit supplies DC voltage to the heater any time the
ambient temperature is low enough. Extended storage
during cold weather will drain the vehicle batteries. To
prevent battery drain, remove the 3 amp fuse from the low
ambient heater.
Art02317
268
269
267
Art02316
268
269
266
NOTICE
Installation Manual 19
Connect the Propane Gas Components
This refrigerator operates on propane gas at a pressure of 11 inches Water Column Propane.
The controls operate on 12 volts DC (10.5 volts min. - 15.4 volts max.). Operation out of these limits can damage the refrigerator
electrical circuit parts and will void the warranty.
Connect the propane gas supply system:
Be very careful when working on or near the propane gas system.
- Do not smoke, or use an open ame near the propane gas system.
- Do not use an open ame to examine for leaks.
- Do not connect the refrigerator to the propane gas tank without a pressure regulator between them.
- To avoid a propane gas leak, always use two wrenches to tighten or loosen the propane gas supply line connections.
- Leaking propane gas can ignite or explode and result in dangerous personal injury or death.
Connect the gas supply line to the refrigerator:
- Make sure that all tubing and ttings obey all local, state, and national codes about size and type.
- Make sure that all exible metal connectors obey the current CAN1-6.10 Standard.
- Make sure that the materials used for the gas supply line obey both the current ANSI A 119.2 (NFPA 1192) and CSA Z240
Standards on Recreational Vehicles. Norcold recommends the use of 3/8 inch copper tubing as the gas supply line and requires a
3/8 inch SAE (UNF 5/8-18) male are tting as the connection to the refrigerator.
- Put the propane gas supply line up through the oor of the enclosure.
- Make sure the hole through the oor is large enough allow clearance for the gas supply line.
- Put a weather resistant seal (grommet, sealant, etc.) around the gas supply line where it goes through the oor to prevent vibration
and abrasion.
- To prevent vibration and abrasion, make sure that the gas supply line is not against anything in the enclosure.
- Attach the gas supply line to the bulkhead tting of the refrigerator.
Examine the propane gas supply line for leaks:
Do not allow the leak detecting solution to touch the electrical components. Many liquids are electrically
conductive and can cause electrical shorts and in some cases, re.
Use a leak detecting solution to examine the gas supply line and all propane gas connections for leaks.
If you use compressed air for the test:
- The pressure of the compressed air at the manual shut o valve of the refrigerator must not be more than 1/2 psig (14 inches Water
Column).
- If the pressure of the compressed air is more than 1/2 psig (14 inches Water Column), remove the gas supply line from the
bulkhead tting of the refrigerator before the test.
- If the pressure of the compressed air is equal to or less than 1/2 psig (14 inches Water Column), close the manual shut o valve of
the refrigerator before the test.
WARNING
!
WARNING
!
Installation Manual 20
Connect the Ice Maker (optional)
The ice maker is assembled to the refrigerators at the factory as optional equipment. If the refrigerator does not have a factory installed
ice maker, one can not be added to the refrigerator at a later time.
The refrigerator installer must connect a cold water supply line to the solenoid valve at the rear of the refrigerator. The following are
necessary to connect the icemaker:
- 1/4 in. OD copper tubing for the water supply line.
OR
- 1/4 in. OD plastic tubing for the water supply line.
- 1/4 in. shut o valve in the water supply line. This should be easily accessible through the lower intake vent.
Connect the water supply line:
Install a 1/4 in. OD water supply line [43] from the water shut o valve of the vehicle to the
solenoid water valve [44] at the rear of the refrigerator (See Art01014):
A brass compression nut [45], a brass sleeve, a plastic sleeve [46] , and a
brass insert [47] are supplied and attached to the rear of the refrigerator (See
Art01604).
- Put the compression nut and then the sleeve onto the water supply line [43].
- For copper tubing, use the brass sleeve.
- For plastic tubing, use the plastic sleeve [46].
- For plastic tubing with .040 in. wall thickness, also use the brass insert [47].
- Flush the water supply line until the water is clear.
- Put the tubing into the adapter [48] until it is against the stop of the adapter.
- Tighten the compression nut by hand (hard nger tight).
- Using two wrenches, tighten the compression nut 1 ½ to 2 turns.
- Open the water shut o valve of the vehicle.
- Examine the connections for leaks.
Art01604
48
47
43
46
45
NOTICE
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
Norcold 1210 Ultraline Guide d'installation
- Catégorie
- Cheminées
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Norcold 1210 Ultraline Guide d'installation
-
-
-
-
-
Norcold N109X Series Le manuel du propriétaire
-