GE PCF25PGSBB Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
ge.com
Refrigerators
Profile Side by Side
200D8074P011 49-60482 11-06 JR
La section française commence à la page 46
La sección en español empieza en la página 88
Safety Instructions . . . . . . . . . . .2–4
Operating Instructions
Automatic Icemaker . . . . . . . . . . .14
Care and Cleaning . . . . . . . . . .16, 17
ClimateKeeper2
. . . . . . . . . . . . . . .6
Crispers and Pans . . . . . . . . . . . . .13
CustomCool
. . . . . . . . . . . . . . . .7, 8
Ice and Water Dispenser . . . . .15–16
QuickFreeze
. . . . . . . . . . . . . . . . .9
Quick Ice . . . . . . . . . . . . . . . . . . . .15
Refrigerator Doors . . . . . . . . . . . .12
Replacing the Light Bulbs . . . . . . .18
Shelves and Bins . . . . . . . . . . .10, 11
Temperature Controls . . . . . . . . . . .5
TurboCool
. . . . . . . . . . . . . . . . . . .6
Water Filter . . . . . . . . . . . . . . . . . . .9
Installation Instructions
Installing the Refrigerator . . . .28–31
Moving the Refrigerator . . . . .24–27
Preparing to Install
the Refrigerator . . . . . . . . . . . . . . .23
Trim Kits and Panels . . . . . . . .19–22
Water Line Installation . . . . . .32–34
Troubleshooting Tips . . . . . . .36–38
Normal Operating Sounds . . . . . .35
Consumer Support
Consumer Support . . . . .Back Cover
Performance Data Sheet . . . . . . . .41
Product Registration . . . . . . . .43, 44
Warranty (Canadian) . . . . . . . . . . .39
Warranty (U.S.) . . . . . . . . . . . . . . .40
Réfrigérateurs
Profile Côte à Côte
Refrigeradores
Profile Lado a Lado
Models 23, 25, 26, 27 and 29
Write the model and serial numbers here:
Model # __________________________
Serial # __________________________
Find these numbers on a label inside
the refrigerator compartment at the
top on the right side.
Owner’s Manual
and Installation
Manuel d’utilisation
et d’installation
Manual del propietario
e instalación
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
2
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
Use this appliance only for its intended purpose as described in this Owner’s Manual.
SAFETY PRECAUTIONS
When using electrical appliances, basic safety precautions should be followed, including the following:
This refrigerator must be properly installed
and located in accordance with the Installation
Instructions before it is used.
Do not allow children to climb, stand or hang
on the shelves in the refrigerator. They could
damage the refrigerator and seriously injure
themselves.
Do not touch the cold surfaces in the freezer
compartment when hands are damp or wet. Skin
may stick to these extremely cold surfaces.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
In refrigerators with automatic icemakers,
avoid contact with the moving parts of the
ejector mechanism, or with the heating element
located on the bottom of the icemaker. Do not
place fingers or hands on the automatic
icemaking mechanism while the refrigerator
is plugged in.
Keep fingers out of the “pinch point” areas;
clearances between the doors and between
the doors and cabinet are necessarily small.
Be careful closing doors when children are
in the area.
Unplug the refrigerator before cleaning and
making repairs.
NOTE: We strongly recommend that any servicing be
performed by a qualified individual.
Non-LCD models: Setting either or both controls to
0 (off) does not remove power to the light circuit.
LCD models: Turning the cooling system off does
not remove power to the light circuit.
Do not refreeze frozen foods which have
thawed completely.
Always clean the CustomCool
Tray after thawing
food.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions Installation Instructions
ge.com
PROPER DISPOSAL OF THE REFRIGERATOR
Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are
still dangerous…even if they will sit for “just a few
days.” If you are getting rid of your old refrigerator,
please follow the instructions below to help prevent
accidents.
Before You Throw Away Your Old Refrigerator
or Freezer:
Take off the doors.
Leave the shelves in place so that children may
not easily climb inside.
Refrigerants
All refrigeration products contain refrigerants,
which under federal law must be removed prior
to product disposal. If you are getting rid of an
old refrigeration product, check with the
company handling the disposal about what
to do.
USE OF EXTENSION CORDS
Because of potential safety hazards under certain conditions, we strongly recommend against the use
of an extension cord.
However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United
States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding
type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.
DANGER! RISK OF CHILD ENTRAPMENT
3
4
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
IMPORTANT SAFETY INFORMATION.
READ ALL INSTRUCTIONS BEFORE USING.
WARNING!
HOW TO CONNECT ELECTRICITY
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For
personal safety, this appliance must be properly grounded.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet
to minimize the possibility of electric shock hazard
from this appliance.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded.
If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall
outlet.
The refrigerator should always be plugged into its
own individual electrical outlet which has a voltage
rating that matches the rating plate.
This provides the best performance and also
prevents overloading house wiring circuits which
could cause a fire hazard from overheated wires.
Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet.
Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.
When moving the refrigerator away from the
wall, be careful not to roll over or damage the
power cord.
READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.
SAVE THESE INSTRUCTIONS
Consumer SupportTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
About the temperature controls. ge.com
NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not
removed during installation, remove it now.
The temperature controls are preset in the factory at 37°F (3°C) for the
refrigerator compartment and 0°F (-18°C) for the freezer compartment.
Allow 24 hours for the temperature to stabilize to the preset
recommended settings.
Refrigerator temperatures can be adjusted between 34°F and 44°F
(1°C to 7°C), and the freezer temperatures can be adjusted between
–6°F and +6°F (–21°C to –14°C).
To change the Refrigerator temperature:
LCD Models:
Access By: Home > Refrigerator
Activate By: Using the arrows to select the desired
temperature. You must press ENTER to set the new
temperature.
To change the Freezer temperature:
Access By: Home > Freezer
Activate By: Using the arrows to select the desired
temperature. You must press ENTER to set the new
temperature.
Once the desired temperature has been set, the display will
return to the HOME screen and show the set temperatures
underneath the actual temperature display for several
seconds. Several adjustments may be required. Each time
you adjust the controls, allow 24 hours for the refrigerator
to reach the temperature you have set.
Non-LCD Models:
To change the temperature, press and release the WARMER
or COLDER pad. The SET light will come on and the display
will show the set temperature. To change the temperature,
tap either the WARMER or COLDER pad until the desired
temperature is displayed.
Once the desired temperature has been set, the
temperature display will return to the actual refrigerator
and freezer temperatures after 5 seconds. Several
adjustments may be required. Each time you adjust the
controls, allow 24 hours for the refrigerator to reach the
temperature you have set.
The temperature controls can display both the SET temperature as well
as the actual temperature in the refrigerator and freezer. The actual
temperature may vary slightly from the SET temperature based on
usage and operating environment.
Turning the cooling system off:
LCD models: Turning the cooling system OFF stops cooling in both the
freezer and refrigerator compartments, but does not shut off electrical
power to the refrigerator.
Non-LCD models: Setting either or both controls to OFF stops cooling in
both the freezer and refrigerator compartments, but does not shut off
electrical power to the refrigerator.
LCD Models:
Access By: Home > Options > Information and Settings >
Cooling System Off
To turn the cooling system back on, press the touch screen
and press the ON button.
Activate By: Pressing ENTER.
Non-LCD Models:
Tap the WARMER pad for either the refrigerator or the
freezer until the display shows OFF. To turn the unit back on,
press the COLDER pad for either the refrigerator or freezer.
The SET light will illuminate on the side you selected. Then
press the COLDER pad again (on the side where the SET
light is illuminated) and it will go to the preset points of 0°F
(–18°C) for the freezer and 37°F (3°C) for the refrigerator.
When the unit is turned back on, it will take up to 24 hours
to stabilize.
The Performance Air-Flow System is designed to maximize
temperature control in the refrigerator and freezer
compartments. This unique special feature consists of the
Air Tower along the back wall of the refrigerator and the
Air Tunnel on the bottom portion of the freezer rear wall.
Placing food in front of the louvers on these components
will not affect performance. Although the Air Tower and
the Air Tunnel can be removed, doing so will affect
temperature performance. (For removal instructions,
on-line, 24 hours a day, contact us at ge.com or call
800.GE.CARES. In Canada, contact us at geappliances.ca
or call 1.800.361.3400.)
Performance Air Flow System
5
LCD models
Non-LCD models
On LCD
models
Not all features are on all models. Your controls will look like one of the following
:
6
About TurboCool.
How it Works
TurboCool
rapidly cools the refrigerator
compartment in order to more quickly
cool foods. Use TurboCool when adding a
large amount of food to the refrigerator
compartment, putting away foods after they
have been sitting out at room temperature
or when putting away warm leftovers. It can
also be used if the refrigerator has been
without power for an extended period.
Once activated, the compressor will turn on
immediately and the fans will cycle on and
off at high speed as needed for eight hours.
The compressor will continue to run until
the refrigerator compartment cools to
approximately 34°F (1°C), then it will cycle
on and off to maintain this setting. After
8 hours, or if TurboCool is pressed again,
the refrigerator compartment will return
to the original setting.
How to Use
LCD Models:
Access By: Home > Options > Refrigerator
Options > TurboCool
Activate By: Pressing ON.
Deactivate By: Pressing OFF.
Non-LCD Models:
Press TurboCool. The refrigerator
temperature display will show TC.
After TurboCool is complete, the refrigerator
compartment will return to the original
setting.
NOTES:
The refrigerator temperature cannot be changed
during TurboCool.
The freezer temperature is not affected during
TurboCool.
When opening the refrigerator door during
TurboCool, the fans will continue to run if they
have cycled on.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
About ClimateKeeper2.
How it Works
The ClimateKeeper2
is the industry’s most
advanced refrigeration system, delivering
optimum temperature and humidity
performance to keep food garden fresh
longer and reduce freezer burn, while
maintaining E star-level efficiency.
The ClimateKeeper2 system features
two evaporators—one for the refrigerator
and one for the freezer.
This provides two separate cooling systems,
and separates the airflow between the fresh
food and freezer compartments during
normal cooling operations.*
This ensures that the humidity levels in the
fresh food compartment are significantly
higher than in a conventional system,**
allowing fresh produce and other unsealed
foods to retain their moisture content and
freshness longer. Moisture sensitive foods
such as fresh fruit, salads, rice, etc., can now
be stored on open shelves without excessive
moisture loss. Due to the higher humidity
in the refrigerator, you may on occasion
experience fog or small amounts of
moisture in the refrigerator compartment.
This is normal and may come and go as
different food loads and environmental
conditions change. Wipe dry with a paper
towel if desired.
The separate airflow system minimizes
the mixing of air between the two
compartments, which reduces fresh food
odor transfer to improve the taste of ice.
The ClimateKeeper2 system also reduces
the number of defrosting cycles in the
freezer evaporator, thereby reducing
freezer burn.
*Freezer air is used in the CustomCool feature.
**Testing shows a higher level of humidity in
the Fresh Food section in ClimateKeeper2
refrigerators versus conventional units.
7
Empty the pan. Place the Chill/Thaw
tray in the pan. Place the items on the
tray and close the pan completely.
LCD Models:
Access by: Home > Options >
Refrigerator Options > CustomCool Pan
Non-LCD Models:
Select the ExpressThaw
, ExpressChill
or SelectTemp
pad. The display and
SET light will come on. Tap the pad
until the light appears next to the
desired setting.
Use the following chart to determine
the best setting to use.
On some models, ExpressChill has
only one 45 minute setting.
To stop a feature before it is finished:
For LCD Models:
Go into that feature’s menu and press
the OFF button.
For Non-LCD Models:
Tap that feature’s pad until no
options are selected and the display
is off.
During ExpressThaw and
ExpressChill, the display on the
controls will count down the time
in the cycle (on some models).
After the ExpressThaw cycle is
complete, the pan will reset to the
MEAT setting (32°F [0°C]) to help
preserve thawed items until they are
used.
The displayed actual temperature of
the CustomCool pan may vary slightly
from the SET temperature based on
usage and operating environment.
NOTE: For food safety reasons, it is recommended
that foods be wrapped in plastic wrap when using
ExpressThaw. This will help contain meat juices
and improve thawing performance.
About CustomCool
. (on some models) ge.com
The CustomCool
feature is used to quickly
chill items, thaw items or hold the pan at a
specific temperature. This feature is a
system of dampers, a fan, a temperature
thermistor and a heater.
The pan is tightly sealed to prevent
temperature fluctuations in the rest of the
refrigerator. The controls for this pan are
located at the top of the refrigerator with
the temperature controls, or on the
dispenser with the temperature controls.
How to Use
How it Works
ExpressThaw
To remove:
Pull the drawer out to the stop position.
Rotate all four swing locks to the unlock
position.
Lift the front of the drawer up and out.
To replace:
Make sure all four swing locks are in the
unlock position.
Place the sides of the drawer into the
drawer supports, making sure the swing
locks fit on the drawer slots.
Lock all four swing locks by rotating
them to the lock position.
How to Remove and Replace the Drawer
ExpressChill
Consumer SupportTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
On LCD
models
8
About CustomCool
. (on some models)
CustomCool
Chart
NOTE: Results may vary depending on packaging, starting temperature and other food traits.
0.5 Lb. (4 hours)
Hamburger Patties (0.5 lb)
Individually Wrapped
Filet Mignon (0.5 lb)
1.0 Lb. (6 hours)
Chicken Breasts (1.0 lb)
Ground Beef (1.0 lb)
Steak (1.0 lb)
2.0 Lbs. (10 hours)
Chicken Breasts (2.0 lbs)
Ground Beef (2.0 lbs)
Steak (2.0 lbs)
3.0 Lbs. (12 hours)
Chicken Breasts (3.0 lbs)
Ground Beef (3.0 lbs)
Steak (3.0 lbs)
15 Minutes
1 Beverage Can (12 oz)
2 Small Juice Boxes (6–8 oz each)
30 Minutes
2 to 6 Beverage Cans (12 oz each)
2 Plastic 20 oz Bottles of Beverage
4 to 6 Small Juice Boxes
(6–8 oz each)
3 Foil Juice Packets
Wine (750 ml bottle)
45 Minutes
2 Liter of Beverage
1/2 Gallon of Juice
Gelatin–1 package
Citrus Setting (43°F [6°C])
Oranges, Lemons, Limes,
Pineapple, Cantaloupe
Beans, Cucumbers, Tomatoes,
Peppers, Eggplant, Squash
Produce Setting (35
°F [2°C])
Strawberries, Raspberries, Kiwifruit,
Pears, Cherries, Blackberries,
Grapes, Plums, Nectarines, Apples
Asparagus, Broccoli, Corn,
Mushrooms, Spinach, Cauliflower,
Kale, Green Onion, Beets, Onions
Meat Setting (32°F [0°C])
Raw Meat, Fish and Poultry
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
Some CustomCool models feature a beverage
center. It is designed to store beverages at
colder temperatures. Select this feature if
you like to keep extra-chilled refreshments
on hand.
LCD Models:
Access by: Home > Options > Refrigerator
Options > Beverage Center
Activate by: Pressing ON.
Deactivate by: Pressing OFF.
Non-LCD Models:
Select the Beverage Center pad. The set
light will come on and the feature will
operate as required.
To turn off the feature, press Beverage
Center pad and set light will turn off.
NOTE: Unless turned off as above, feature will
remain active for six months. Press the Beverage
Center pad to restart.
How to Use the Beverage Center
To remove:
Remove dairy bin first. Holding the
bottom of the dairy bin, lift the front
straight up, then lift up and out.
Holding left and right side of beverage
center, lift straight up and out.
Leave adapter in place.
To replace:
Engage backside of beverage center in
molded supports on adapter. Then
push down on the sides of the beverage
center. The beverage center will lock
into place.
Replace dairy bin.
How to Remove and Replace the Beverage Center
Dairy Bin
Adapter
Beverage
Center
About QuickFreeze.
(on some models) ge.com
The QuickFreeze plate is only to be
used with the QuickFreeze feature.
Use QuickFreeze to freeze items faster
to enhance food preservation.
How to Use
Place food (wrapped in plastic wrap) on
QuickFreeze plate. Turn the feature on via
the LCD controls.
LCD Models:
Access By: Home > Options > Freezer
Options > QuickFreeze
Activate By: Using the arrows to select the
time and pressing Enter.
Deactivate By: Pressing OFF.
NOTE: While the QuickFreeze feature is
enabled, the actual freezer temperature may
drop as low as –3°F (–19°C). This is normal.
Consumer SupportTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
About the water filter.
Water Filter Cartridge
The water filter cartridge is located in the
back upper right corner of the refrigerator
compartment.
When to Replace the Filter
LCD Models:
A pop-up screen will appear on the LCD screen
to remind you to replace the water filter. You can
check the status of the water filter manually.
Access By: Home > Options > Dispenser Options
> Reset Water Filter
Non-LCD Models:
There is a replacement indicator light for the
water filter cartridge on the dispenser. This light
will turn orange to tell you that you need to
replace the filter soon.
The filter cartridge should be replaced when the
replacement indicator light turns red or if the
flow of water to the dispenser or icemaker
decreases.
Removing the Filter Cartridge
If you are replacing the cartridge, first remove
the old one by slowly turning it to the left. Do not
pull down on the cartridge. A small amount of
water may drip down.
Installing the Filter Cartridge
There is an adapter attached to the top of
the new filter cartridge.
The adapter must be removed before
installing the cartridge. To remove the
adapter, turn it to the left about 1/4 turn.
Fill the replacement cartridge with water
from the tap to allow for better flow from
the dispenser immediately after installation.
Line up the arrow on the cartridge and the
cartridge holder. Place the top of the new
cartridge up inside the holder. Do not push
it up into the holder.
Slowly turn it to the right until the filter
cartridge stops. DO NOT OVERTIGHTEN. As
you turn the cartridge, it will automatically
raise itself into position. The cartridge will
rotate about 1/2 turn.
Run water from the dispenser for 5 minutes
to clear the system and prevent sputtering.
LCD Models:
Press FILTER REPLACED button
to confirm replacement.
Non-LCD Models:
Press and hold the RESET FILTER pad
(on some models) on the dispenser for
3 seconds.
NOTE: A newly installed water filter cartridge may cause
water to spurt from the dispenser.
Filter Bypass Plug
You must use the filter bypass plug when a
replacement filter cartridge is not available.
The dispenser and the icemaker will not operate
without the filter or filter bypass plug.
Replacement Filters:
To order additional filter cartridges in the United
States, visit our Website, ge.com, or call GE Parts
and Accessories, 800.626.2002.
MSWF
Suggested Retail $36.95–$41.95 USD
Customers in Canada should consult
the yellow pages for the nearest Mabe Service
Center.
Place the top of the cartridge up
inside the cartridge holder and
slowly turn it to the right.
QuickFreeze
Plate
Filter
Bypass
Plug
SmartWater
Cartridge
Holder
9
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
10
About the shelves and bins.
Refrigerator Door Bins and Freezer Door Tilt-Out Bins
Bins
The larger refrigerator door bins and
freezer tilt-out door bins are adjustable.
To remove: Lift the front of the bin straight
up, then lift up and out.
To replace or relocate: Engage the back side
of the bin in the molded supports on the
door. Then push down on the front of the
bin. Bin will lock in place.
The snugger helps prevent tipping, spilling
or sliding of small items stored on the door
shelf. Place a finger on either side of the
snugger near the rear and move it back
and forth to fit your needs.
Top Freezer Bins
Not all features are on all models.
Refrigerator bin
Freezer tilt-out bin
Snugger
QuickSpace
Shelf
This shelf splits in half and slides under
itself for storage of tall items on the shelf
below.
This shelf can be removed and replaced
or relocated just like Slide-Out Spillproof
Shelves.
On some models, this shelf cannot be used
in the lowest position.
Slide-Out Spillproof Shelf
The slide-out spillproof shelf allows you
to reach items stored behind others. The
special edges are designed to help prevent
spills from dripping to lower shelves.
To remove:
Slide the shelf out until it reaches the stop,
then press down on the tab and slide the
shelf straight out.
To replace or relocate:
Line the shelf up with the supports and
slide it into place. The shelf can be
repositioned when the door is at 90° or
more. To reposition the shelf, slide the shelf
past the stops and angle downward. Slide
shelf down to the desired position, line up
with the supports and slide into place.
Make sure you push the shelves all the way back
in before you close the door.
Press tab and pull shelf forward
to remove
Top freezer bin
Do not block
CAUTION:
Be careful when
placing items in the
top bin. Make sure
that items do not
block or fall into
the ice chute.
Top freezer bin (on some models)
Do not block
CAUTION:
Part must be in
place as shown
for proper ice
dispensing. Food
cannot be stored
in this location.
ge.com
Not all features are on all models.
Slide-Out Freezer Shelves
To remove, slide out to the stop position,
lift the front past the stop position and
slide out.
Make sure you push the shelves all the way back
in before you close the door.
Freezer Baskets
To remove, push the basket all the way to the
back of the freezer. Lift up until the back
pins are disengaged. Lift the entire basket
up and pull out.
Make sure you push the baskets all the way back
in before you close the door.
Fixed Freezer Shelves
There are two types of fixed
freezer shelves.
To remove this type of shelf:
Lift the shelf up at the left side.
Bring the shelf out.
To remove this type of shelf:
Lift up the left side of the shelf and
slide it left into the center of the shelf
supports.
Rotate the right side of the shelf up
and out of the shelf supports.
NOTE FOR DISPENSER MODELS: In order to take
full advantage of the tilt-out ice bin, only store items
on the shelf below the ice bin that are no taller than
the lowest point on the bin.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions Installation Instructions
Door Wine/Beverage Rack (on some models)
This rack holds up to 5 cans, one bottle of
wine or one 2-liter bottle of soda.
The rack hangs from the sides of the
dairy bin.
To remove:
Empty the wine/beverage rack.
Holding the bottom of the dairy bin,
lift the front straight up, then lift up
and out.
To detach the rack from the dairy bin,
pull the rack’s side wires out of the
holes on each side of the dairy bin.
To replace:
Reattach the rack to the sides
of the bin.
Engage the back side of the bin in
the molded supports on the door.
Then push down on the front of the
bin. The bin will lock into place.
11
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
12
About the refrigerator doors.
Refrigerator Doors
The refrigerator doors may feel different
than the ones you are used to. The special
door opening/closing feature makes sure
the doors close all the way and are securely
sealed.
When opening and closing the door you
will notice a stop position. If the door is
opened past this stop point, the door will
remain open to allow you to load and
unload food more easily. When the door
is only partially open, it will automatically
close.
The resistance you feel at the stop
position will be reduced as the door
is loaded with food.
When the door is only partially open,
it will automatically close.
Beyond this stop the door will stay open.
Door Alignment
If doors are uneven, adjust the refrigerator
door.
Using a 7/16wrench, turn the door
adjusting screw to the right to raise the
door, to the left to lower it. (A nylon
plug, imbedded in the threads of the
pin, prevents the pin from turning
unless a wrench is used.)
After one or two turns of the wrench,
open and close the refrigerator door
and check the alignment at the top of
the doors.
7/16Wrench
Raise
About the crispers and pans. ge.com
13
About crisper removal.
Not all features are on all models.
Crisper Removal
Crispers can easily be removed by pulling
the drawer straight out and lifting the
drawer up and over the stop location.
If the door prevents you from taking out
the drawers, first try to remove the door
bins. If this does not offer enough
clearance, the refrigerator will need to
be rolled forward until the door opens
enough to slide the drawers out. In some
cases, when you roll the refrigerator out,
you will need to move the refrigerator
to the left or right as you roll it out.
Not all features are on all models.
Fruit and Vegetable Crispers
Excess water that may accumulate in the
bottom of the drawers should be wiped dry.
On some models, the bottom drawer has
full extension slides that allow full access
to the drawer.
Adjustable Humidity Crispers
Slide the control all the way to the HI setting
to provide high humidity recommended for
most vegetables.
Slide the control all the way to the LO
setting to provide lower humidity levels
recommended for most fruits.
HI LO
Convertible Deli Pan
The convertible deli pan has its own cold
air duct to allow a stream of cold air from
the freezer compartment or fresh food
compartment to flow to the pan.
The variable temperature control regulates
the air flow from the Climate Keeper.
Set the control to the coldest setting to
store fresh meats.
Set the control to cold to convert the pan
to normal refrigerator temperature and
provide extra vegetable storage space. The
cold air duct is turned off. Variable settings
between these extremes can be selected.
C
O
L
D
C
O
L
D
E
S
T
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions Installation Instructions
About the automatic icemaker.
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
14
Automatic Icemaker
The icemaker will produce seven cubes
per cycle—approximately 100–130 cubes
in a 24-hour period, depending on freezer
compartment temperature, room
temperature, number of door openings
and other use conditions.
If the refrigerator is operated before the
water connection is made to the icemaker,
set the power switch in the O (off) position.
When the refrigerator has been connected
to the water supply, set the power switch to
the l (on) position.
The icemaker will fill with water when it
cools to 15°F (–10°C). A newly installed
refrigerator may take 12 to 24 hours to begin
making ice cubes.
You will hear a buzzing sound each time
the icemaker fills with water.
Throw away the first few batches of ice to
allow the water line to clear.
Be sure nothing interferes with the sweep
of the feeler arm.
When the bin fills to the level of the feeler
arm, the icemaker will stop producing
ice. It is normal for several cubes to be
joined together.
If ice is not used frequently, old ice cubes
will become cloudy, taste stale and shrink.
Special note about dispenser models:
Dispenser models have a tilt-out ice bin.
The bin can be tilted out as shown in the
illustrations, and it will hold itself up
while you take ice out or turn the
icemaker power switch on and off. Be
sure to put the bin back in place before
closing the door.
To restore your ice level from an empty
bucket stage, the following steps are
recommended:
12 hours after the first batch of ice
has fallen into the bin, dispense
3 to 4 cubes.
After an additional 6 hours, dispense
3 to 4 cubes again.
These steps will restore your ice level
in the shortest amount of time.
NOTE: In homes with lower-than-average water
pressure, you may hear the icemaker cycle multiple
times when making one batch of ice.
A newly installed refrigerator may take 12 to 24 hours to begin making ice.
Lift the bin, then pull it
forward until the bin stops.
Removing Ice Bin (dispenser models)
CAUTION: The ice bin is heavy when full.
Set the power switch to the O (off) position
before removing the bin.
When replacing the bin, be sure to press it
firmly into place. If it does not go all the
way back, remove it and rotate the drive
mechanism 1/4 turn. Then push the bin
back again.
Icemaker
Feeler Arm
Power
Switch
Green
Power Light
Lower the bin to access ice
or reach the power switch.
NOTE: In order to take full advantage
of the tilt-out ice bin, only store items
on the shelf below the ice bin that
are no taller than the lowest point
on the bin.
On dispenser models,
to access ice or reach
the power switch:
Lift the bin, then pull it
forward until the bin stops.
Lift and pull forward again
to remove the bin.
Rotate
Drive
Mechanism
Dispenser Models only
About the ice and water dispenser. (on some models) ge.com
To Use the Dispenser
Select CUBED, CRUSHED or WATER.
Press the glass gently against the top of the
dispenser cradle.
The spill shelf is not self-draining. To reduce
water spotting, the shelf and its grille should be
cleaned regularly.
If no water is dispensed when the refrigerator is first
installed, there may be air in the water line system. Press
the dispenser arm for at least two minutes to remove
trapped air from the water line and to fill the water
system. To flush out impurities in the water line, throw
away the first six glassfuls of water.
CAUTION: Never put fingers or any other objects into
the ice crusher discharge opening.
Locking the Dispenser
Press the LOCK pad for 3 seconds to lock the
dispenser and control panel. To unlock, press
and hold the pad again for 3 seconds.
Dispenser Light
The LIGHT pad turns the night light in the
dispenser on and off. The light also comes on
when the dispenser cradle is pressed. On some
models, if this light burns out, it should be
replaced with a 6 watt 12V maximum bulb.
Door Alarm
Use Door Alarm to sound if either door is open
for more than 3 minutes. The alarm will stop
once the door is closed. For LCD models, a
popup screen will appear. The alarm can be
silenced by touching the LCD screen.
LCD Models:
Access By: Home > Options > Information and
Settings > Settings > Door Alarm
Access By: Pressing ON.
Deactivate By: Pressing OFF.
Non-LCD Models:
Press the DOOR ALARM pad until the indicator
light comes on.
Spill Shelf
Consumer SupportTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
Precise Fill (on some models)
Quick Ice
This water dispenser is equipped with a feature
called “precise fill.” This feature allows you to
choose a precise amount of water (cups or
ounces) that you would like dispensed. Pints
and Liters are also available for LCD models.
LCD Models
Access By: Home > Options > Dispenser
Options > Precise Fill > Set Amount
Activate By: Using the arrow buttons to select
the desired amount. Press MORE UNITS to select
between CUPS, OUNCES, PINTS or LITERS.
Non-LCD Models
Press the WATER pad.
Press the CUPS or OUNCES pad.
Select the precise amount of water you
would like dispensed.
If you selected OUNCES, press the arrow
pads on either side of the display to
select the number of ounces you
would like to have dispensed between
1–99 ounces.
If you selected CUPS, press the arrow
pads on the left of the display to select
the whole cups (1–16 cups) and/or
the arrow pads on the right side of the
display to select fractions of a cup
(1/4–3/4 cups).
Press the cup against the cradle and water
will begin dispensing. It will automatically
stop when the amount set has been
dispensed. The display will show there
is no water left to dispense, then reset.
NOTE: Do not leave the dispenser unattended when
water is being dispensed.
If you would like to stop dispensing water
before the specified amount has been
dispensed, just remove the cup from the
cradle. The display will show the amount
left to dispense.
When you need to speed up ice production, use
the Quick Ice feature. While this feature is turned
on, the freezer fan runs continuously for 48 hours,
or until the feature is turned OFF. During this
period, ice production will increase up to 40%.
Models with the integrated ice feature system
require at FIRST USE at least half an 8 oz. glass
of ice to be dispensed every 6 to 12 hours. This
will help the icemaker fill the bucket properly
so that dispensing is better.
How to Use
LCD Models:
Access by: Home > Options > Freezer Options >
Quick Ice
Activate by: Pressing ON.
Deactivate by: Pressing OFF.
Non-LCD Models:
Press the QUICK ICE pad to turn the feature ON.
Press the pad again to turn the feature OFF.
15
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
16
Cleaning the Outside
The dispenser drip area, beneath the grille,
should be wiped dry. Water left in this area
may leave deposits. Remove the deposits by
adding undiluted vinegar to the well. Soak
until the deposits disappear or become
loose enough to rinse away.
The dispenser cradle. Before cleaning, lock
the dispenser by pressing and holding the
LOCK pad for 3 seconds. Clean with warm
water and baking soda solution—about a
tablespoon (15 ml) of baking soda to a
quart (1 liter) of water. Rinse thoroughly
and wipe dry.
The door handles and trim. Clean with
a cloth dampened with soapy water.
Dry with a soft cloth.
The stainless steel panels and door handles
(on some models) can be cleaned with
a commercially available stainless steel
cleaner. A spray-on stainless steel cleaner
works best.
Do not use appliance wax or polish
on the stainless steel.
Keep the outside clean. Wipe with a clean
cloth lightly dampened with kitchen
appliance wax or mild liquid dish detergent.
Dry and polish with a clean, soft cloth.
Do not wipe the refrigerator with a soiled dish
cloth or wet towel. These may leave a residue
that can erode the paint. Do not use scouring
pads, powdered cleaners, bleach or cleaners
containing bleach because these products can
scratch and weaken the paint finish.
Cleaning the Inside
To help prevent odors, leave an open box of
baking soda in the fresh food and freezer
compartments.
Unplug the refrigerator before cleaning. If this
is not practical, wring excess moisture out
of sponge or cloth when cleaning around
switches, lights or controls.
Use warm water and baking soda solution—
about a tablespoon (15 ml) of baking soda
to a quart (1 liter) of water. This both
cleans and neutralizes odors. Rinse and
wipe dry.
Use of any cleaning solution other than that
which is recommended, especially those that
contain petroleum distillates, can crack or
damage the interior of the refrigerator.
Avoid cleaning cold glass shelves with hot water
because the extreme temperature difference
may cause them to break. Handle glass shelves
carefully. Bumping tempered glass can cause
it to shatter.
Do not wash any plastic refrigerator parts
in the dishwasher.
The chill/thaw tray is dishwasher safe.
Dispenser drip area.
Care and cleaning of the refrigerator.
About the ice and water dispenser. (on some models)
Important Facts About Your Dispenser
Do not add ice from trays or bags to
the storage drawer. It may not crush or
dispense well.
Avoid overfilling glass with ice and use
of narrow glasses. Backed-up ice can
jam the chute or cause the door in the
chute to freeze shut. If ice is blocking
the chute, poke it through with a
wooden spoon.
Beverages and foods should not be
quick-chilled in the ice storage drawer.
Cans, bottles or food packages in the
storage drawer may cause the icemaker
or auger to jam.
To keep dispensed ice from missing
the glass, put the glass close to, but not
touching, the dispenser opening.
Some crushed ice may be dispensed
even though you selected CUBED.
This happens occasionally when a few
cubes accidentally get directed to
the crusher.
After crushed ice is dispensed, some
water may drip from the chute.
Sometimes a small mound of snow
will form on the door in the ice chute.
This condition is normal and usually
occurs when you have dispensed
crushed ice repeatedly. The snow
will eventually evaporate.
17
For long vacations or absences, remove
food and unplug the refrigerator. Clean the
interior with a baking soda solution of one
tablespoon (15 ml) of baking soda to one
quart (1 liter) of water. Leave the doors
open.
Set the icemaker power switch to the O (off)
position and shut off the water supply to
the refrigerator.
If the temperature can drop below freezing,
have a qualified servicer drain the water
supply system to prevent serious property
damage due to flooding.
ge.com
Behind the Refrigerator
Be careful when moving the refrigerator
away from the wall. All types of floor
coverings can be damaged, particularly
cushioned coverings and those with
embossed surfaces.
Pull the refrigerator straight out and return
it to position by pushing it straight in.
Moving the refrigerator in a side direction
may result in damage to the floor covering
or refrigerator.
When pushing the refrigerator back, make sure
you don’t roll over the power cord or icemaker
supply line.
Preparing for Vacation
Preparing to Move
Secure all loose items such as shelves and
drawers by taping them securely in place
to prevent damage.
When using a hand truck to move the
refrigerator, do not rest the front or back
of the refrigerator against the hand truck.
This could damage the refrigerator. Handle
only from the sides of the refrigerator.
Be sure the refrigerator stays in an upright
position during moving.
Consumer SupportTroubleshooting Tips
Operating Instructions
Safety Instructions Installation Instructions
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
18
Replacing the light bulbs.
Setting the controls to OFF does not remove power to the light circuit.
Not all features are on all models.
Refrigerator Compartment—Upper Light
Unplug the refrigerator.
The bulbs are located at the top of the
compartment, inside the light shield.
On some models, a screw at the front of
the light shield will have to be removed.
On other models, the screw is located
in the pocket located at the back of the
light shield.
To remove the light shield, on some
models, press in on the tabs on the
sides of the shield and slide forward
and out. On other models, just slide
the shield forward and out.
After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the light shield and
screws (on some models). When
replacing the light shield, make sure
that the tabs at the back of the shield
fit into the slots at the back of the light
shield housing.
Plug the refrigerator back in.
Refrigerator Compartment—Lower Light
This light is located above the top drawer.
Unplug the refrigerator.
Remove the convertible meat drawer
control knob by pulling straight out.
Lift the light shield up and pull it out.
After replacing the bulb with an
appliance bulb of the same or lower
wattage, replace the shield and
the knob.
Plug the refrigerator back in.
Freezer Compartment
Unplug the refrigerator.
Remove the shelf just above the light
shield. (The shelf will be easier to
remove if it is emptied first.) On some
models, a screw at the top of the light
shield will need to be removed.
To remove the light shield, press in
on the sides, and lift up and out.
Replace the bulb with an appliance
bulb of the same or lower wattage,
and reinstall the light shield. When
reinstalling the light shield, make
sure the top tabs snap securely
into place. Replace the screw
(on some models).
Reinstall the shelf and plug the
refrigerator back in.
C
O
L
D
C
O
L
D
E
S
T
Dispenser (on some models)
Unplug the refrigerator.
The bulb is located on the dispenser
under the control panel.
Remove the light bulb by turning
it counterclockwise.
Replace the bulb with a bulb of the
same size and wattage.
Plug the refrigerator back in.
Tabs
Pocket
OR
Your light shield will look like
one of the following:
19
Trim kits and decorator panels.
Read these instructions completely and carefully.
Before You Begin
Some models are equipped with trim kits that allow you to install door panels. You can order
pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,
800.626.2002, or you can add wood panels to match your kitchen cabinets.
Panels less than 1/4(6 mm) thick
When installing wood panels less than 1/4(6 mm) thick, you need to create a filler panel, such as 1/8
cardboard, that will fit between the face of the door and the wood panel. If you are installing the pre-cut
decorator panels, pre-cut filler panels are included in the kit. The combined thickness of the decorator
or wood panel and the filler panel should be 1/4(6 mm).
For CustomStyle
models
3/4(19 mm) or Raised Panel
A raised panel design screwed or glued to a 1/4(6 mm) thick backing, or a 3/4 (19 mm) routed board
can be used. The raised portion of the panel must be fabricated to permit clearances of at least 2(5.1 cm)
from the handle side for fingertip clearance.
Panels thicker than 1/4(6 mm), up to 3/4(19 mm) max, will require that the outer 5/16 (8 mm) of
panel perimeter be no thicker than 1/4(6 mm).
Weight limitations for custom panels:
Fresh Food 38 lbs. (17 kg) max.
Freezer Door 28 lbs. (13 kg) max.
2 (5.1 cm)
Clearance
Handle Side
Appearance
Panel
Refrigerator
Door
1/4 (6 mm)
Thick Backing
3/4
(19 mm)
Panels 1/4 thick or less
Panels thicker than 1/4 (6 mm)
1/4 max
1/4 (6 mm) max
3/4 (19 mm)
5/16(8 mm)
Consumer SupportTroubleshooting Tips
Operating InstructionsSafety Instructions
Installation Instructions
Consumer Support Troubleshooting Tips
Operating Instructions Safety InstructionsInstallation Instructions
20
Trim kits and decorator panels.
Freezer Panel
Without Dispenser
Freezer Panel
With Dispenser Fresh Food Panel
Cutout
5/16
(8 mm)
14
15
32
(36.8 cm)
67
9
32
(170.9 cm)
1/8(3 mm)
FRONT
17
7
8
(45.4 cm)
14
15
32
(36.8 cm)
33
5
8
(85.4 cm)
FRONT
67
9
32
(170.9 cm)
19
15
32
(49.5 cm)
FRONT
23‘ Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
25‘
CustomStyle
Dimensions for Custom Wood Panels
The areas at the top of the panels need to be cut out of the panels.
Cutout
1/8(3 mm)
Cutout
1/8(3 mm)
5/16
(8 mm)
5/16
(8 mm)
Freezer Panel
Without Dispenser
Freezer Panel
With Dispenser Fresh Food Panel
Cutout
5/16
(8 mm)
14
15
32
(36.8 cm)
69
(175.3 cm)
1/8(3 mm)
FRONT
17
(43.2 cm)
14
15
32
(36.8 cm)
36
1
4
(92.0 cm)
FRONT
69
(175.3 cm)
19
15
32
(49.5 cm)
FRONT
Cutout
1/8(3 mm)
Cutout
1/8(3 mm)
5/16
(8 mm)
5/16
(8 mm)
1 / 1

GE PCF25PGSBB Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

dans d''autres langues