Whirlpool WED4950HW Manuel utilisateur

Marque: Whirlpool

Modèle: WED4950HW

Catégorie: Sèche-linge

Taper: Manuel utilisateur

ELECTRIC OR GAS DRYER

USE AND CARE GUIDE

Table of Contents Table des matières

DRYER SAFETY ............................................................2

CHECK YOUR VENT SYSTEM

FOR GOOD AIR FLOW .................................................4

USE ACCUDRY™/AUTOMATIC DRY CYCLES FOR

BETTER FABRIC CARE AND ENERGY SAVINGS ......4

CONTROL PANEL & FEATURES ..................................5

CYCLE GUIDE ............................................................... 6

USING YOUR DRYER ...................................................7

DRYER CARE ................................................................9

TROUBLESHOOTING .................................................11

WARRANTY ................................................................. 13

ASSISTANCE OR SERVICE .................... BACK COVER

SÉCURITÉ DE LA SÉCHEUSE ...................................14

VÉRIFICATION D’UNE CIRCULATION D’AIR

ADÉQUATE POUR LE SYSTÈME D’ÉVACUATION ..16

UTILISATION DES PROGRAMMES

AUTOMATIQUES POUR UN MEILLEUR SOIN

DU TISSU ET DAVANTAGE D’ÉCONOMIES

D’ÉNERGIE .................................................................. 16

TABLEAU DE COMMANDE

ET CARACTÉRISTIQUES ...........................................17

GUIDE DE PROGRAMMES ........................................18

UTILISATION DE LA SÉCHEUSE ............................... 19

ENTRETIEN DE LA SÉCHEUSE ................................. 21

DÉPANNAGE. ..............................................................24

GARANTIE. ..................................................................26

ASSISTANCE OU SERVICE ... COUVERTURE ARRIÈRE

SÉCHEUSE

ÉLECTRIQUE OU À GAZ

GUIDE D’UTILISATION

ET D’ENTRETIEN

Para una versión de estas instrucciones en español, visite www.whirlpool.com

W11185731A

W11185733A - SP

Dryer Safety

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death or property

damage.

–

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building, or area of all occupants.

•

Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

•

If you cannot reach your gas supplier, call the fire department.

–

Installation and service must be performed by a qualified installer, service agency, or

the gas supplier.

Check Your Vent System for Good Air Flow

Good air  ow

Along with heat, dryers require good air  ow to ef ciently

dry laundry. Proper venting will reduce your drying times

and improve your energy savings. See Installation

Instructions.

The venting system attached to the dryer plays a big role

in good air  ow.

Service calls caused by improper venting are not covered

by the warranty and will be paid by the customer, regardless

of who installed the dryer.

Maintain good air  ow:

Good Better

Use the ACCUDRY™/Automatic Dry cycles to provide the most energy savings and enhanced fabric care from the dryer.

During ACCUDRY™/Automatic Dry cycles, drying air temperature or moisture level are sensed in the load. This sensing occurs

throughout the drying cycle and the dryer shuts off when the load reaches the selected dryness.

With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to

overdrying. Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.

Clean your lint screen before each load.

Replace plastic or foil vent material with 4" (102 mm)

diameter heavy, rigid vent material.

Use the shortest length of vent possible.

Use no more than four 90° elbows in a vent system;

each bend and curve reduces air  ow.

Remove lint and debris from the exhaust hood.

Remove lint from the entire length of the vent system

at least every 2 years. When cleaning is complete,

be sure to follow the Installation Instructions supplied

with your dryer for  nal product check.

Clear away items from the front of the dryer.

Use ACCUDRY

™

/Automatic Dry Cycles

for Better Fabric Care and Energy Savings

Control Panel & Features

WRINKLE SHIELD™ Feature (on some models)

When you are unable to remove a load of clothes from the

dryer as soon as it stops, wrinkles can form. The Wrinkle

Shield™ feature periodically tumbles, rearranges, and uffs

the load to help keep wrinkles from forming.

Get 90minutes of heat-free, periodic tumbling at the end

of a cycle. Turn the Wrinkle Shield™ knob to On or Off

at any time before the cycle has ended.

DRYER CYCLE KNOB

Use your Dryer Cycle knob to select available cycles on

your dryer. Turn the knob to select a cycle for your laundry

load. See “Cycle Guide” for detailed descriptions of cycles.

TIMED DRY

Will run the dryer for the specied time on the control.

On models with a selectable temperature knob, you may

choose a setting based on the fabrics in your load. Drying

time and temperature will depend on your dryer model.

ACCUDRY™/AUTOMATIC DRY

Senses moisture in the load or air temperature and shuts

off when the load reaches the selected dryness level.

Gives the best drying in the shortest time. Drying time will

vary based on fabric type, load size, and dryness setting.

TEMPERATURE

Select a drying temperature based on the fabrics in your

load. If you are unsure of the temperature to select for a

load, select the lower setting rather than the higher setting.

NOTE: The No Heat temperature setting (on some models)

is not available on ACCUDRY™ cycles.

CYCLE SIGNAL/PUSH TO START

The Cycle Signal produces an audible sound when the

drying cycle is nished. Promptly removing clothes at the

end of the cycle reduces wrinkling.

Turn the Cycle Signal knob to select the desired setting

(On or Off). Press the PUSH to START knob to start

the dryer.

NOTE: When the Wrinkle Shield™ setting is selected

and the Cycle Signal is on, the tone will sound every

5minutes until the clothes are removed or the Wrinkle

Shield™ setting ends.

Not all features and options are available on all models. Appearance may vary.

2 31 4

2 3 4

Items to dry:

Temperature:

Available

Options:

Cycle Details:

Wrinkle Shield™

Temperature

Cycle Signal

Cycle Guide – ACCUDRY

™

/Automatic Dry Cycles

Not all cycles and settings are available on all models.

ACCUDRY™ – Senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.

Items to dry: Temperature:Cycle:

Available

Options:

Cycle Details:

Large or heavy items

such as thick towels

or robes

Any load

Heavy Dry

or Heavy Duty

Damp Dry Any

Temperature

Choose High to dry large or heavy loads.

Dries items to a damp level or for items

that do not require an entire drying

cycle.

Casual, shirts, pants,

lightweight items,

synthetics, delicates,

athletic wear

Any

Wrinkle Shield™

Temperatur

Cycle Signal

Setting the Drying Temperature

If your dryer has multiple heat settings:

A High temperature setting may be used for drying

heavyweight items such as towels and work clothes.

A Low to Medium temperature setting may be used for drying

medium-weight items such as sheets, blouses, dresses,

underwear, permanent press fabrics, and some knits.

Use the No Heat setting for foam, rubber, plastic, or heat-

sensitive fabrics.

Line dry bonded or laminated fabrics.

NOTE: If you have questions about drying temperatures

for various loads, refer to the care label directions.

Jeans, heavy work

clothes, towels

Energy Preferr

Delicate

or Less Dry

Jeans, More,

or Very Dry

Wrinkle Shield™

Temperature

Cycle Signal

Automatic cycles give the best drying

in the shortest time. Drying time varies

based on fabric type, load size, and

dryness setting.

Select a drying temperature based on

the fabrics in your load. If you are unsure

of the temperature to select for a load,

select the lower setting rather than the

higher setting.

Cycle:

High

Medium

Low

Work clothes, medium

weight fabrics, sheets

Rubber, plastic, heat

sensitive fabrics

Fluff Air

No Heat

Temperature

No heat drying.

Normal

NOTE: If loads do not seem as dry as you would like, select More or Very Dry the next time you dry a similar load. If loads seem

drier than you like, select Less Dry the next time you dry a similar load.

Cycle Guide – Timed Dry Cycles

Not all cycles and settings are available on all models.

TIMED DRY – Will run the dryer for the specifi ed time on the control.

NOTE: Government energy certifications for the Whirlpool Gas and Electric models were based on the Timed Dry cycle with the

Maximum drying temperature setting. The as-shipped defaults of Auto Dry, Normal cycle, Low heat, wrinkle shield were not used.

Using Your Dryer

1. Clean the lint screen

Clean the lint screen before each load. Pull the lint screen out

of its holder. Roll lint off the screen with your  ngers. Do not rinse

or wash screen to remove lint. Push the lint screen  rmly back

into place.

For additional cleaning information, see “Dryer Care”.

2. Load the dryer

Place laundry in the dryer. Close the door.

NOTE: Your model may have a different door than

the one shown. Some models have drop down doors.

Do not tightly pack the dryer; clothes should be able

to tumble freely.

WARNING: To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUCTIONS before

operating this dryer.

Before using your dryer, wipe the dryer drum with a damp cloth

to remove dust from storing and shipping.

6. Press PUSH to START

to begin cycle

Push and hold the PUSH to START knob to begin the cycle.

Promptly remove garments after cycle has completed to reduce

wrinkling. Use the Wrinkle Shield™ feature to avoid wrinkling

when you are unable to remove a load from the dryer as soon

as it stops.

4. Set cycle settings and options

Select cycle settings and options by turning the knob to the

desired position.

NOTE: Not all options and settings are available with all cycles.

Temperature

Turn the Temperature knob to change the drying temperature

setting. See “Setting the Drying Temperature”.

Wrinkle Shield™ feature (on some models)

Get 90 minutes of heat-free, periodic tumbling at the

end of a cycle. Turn the Wrinkle Shield™ knob to select

on or off at any time before the cycle has ended.

Some models with a Wrinkle Shield™ cycle will

automatically get 40 minutes of heat-free, periodic

tumbling at the end of a cycle.

3. Select the desired cycle

Select the desired cycle for your load. See the “Cycle Guide”

for more information about each cycle.

ACCUDRY™/Automatic Dry Cycles

You can select a different dryness level, depending on your

load, by turning the knob to dryness level.

Selecting More or Very Dry, Normal, ENERGY PREFERRED,

or Less Dry automatically adjusts the dryness level at which

the dryer will shut off. Once a dry level is set, it cannot be

changed without stopping the cycle.

ACCUDRY™/AUTOMATIC DRY cycles give the best drying in

the shortest time. Drying time varies based on fabric type, load

size, and dryness setting.

NOTE: More or Very Dry removes more load moisture.

ENERGY PREFERRED or Normal is used for a starting point

for ACCUDRY™ cycles. Less Dry removes less moisture

and is used for loads you may want to put on a hanger

to complete drying.

5. Select Cycle Signal (if desired)

Turn the Cycle Signal knob to select the desired setting

(On or Off). The Cycle Signal produces an audible sound

when the drying cycle is  nished. Promptly removing clothes

at the end of the cycle reduces wrinkling.

NOTE: When the Wrinkle Shield™ setting is selected and the

Cycle Signal is On, the tone will sound every 5minutes until

the clothes are removed, or the Wrinkle Shield™ setting ends.

Control panel and cycles may vary, depending on model.

Dryer Care

Keep dryer area clear and free from items that would

block the air  ow for proper dryer operation. This includes

clearing piles of laundry in front of the dryer.

Cleaning the lint screen

Every load cleaning

The lint screen is located in the dryer. A screen blocked

by lint can increase drying time.

To clean:

1. Pull the lint screen out of its holder. Roll lint off the

screen with your  ngers. Do not rinse or wash screen

to remove lint. Wet lint is hard to remove.

2. Push the lint screen  rmly back into place.

IMPORTANT:

Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can cause

overheating and damage to both the dryer and fabrics.

If lint falls off the screen into the dryer during removal,

check the exhaust hood and remove the lint. See

“Venting Requirements.”

As needed cleaning

Laundry detergent and fabric softener residue can build

up on the lint screen. This buildup can cause longer drying

times for your clothes, or cause the dryer to stop before

your load is completely dry. The screen is probably clogged

if lint falls off while the screen is in the dryer.

Clean the lint screen with a nylon brush every 6 months,

or more frequently, if it becomes clogged due to a residue

buildup.

To wash:

1. Roll lint off the screen with your  ngers.

2. Wet both sides of lint screen with hot water.

3. Wet a nylon brush with hot water and liquid detergent.

Scrub lint screen with the brush to remove residue

buildup.

4. Rinse screen with hot water.

5. Thoroughly dry lint screen with a clean towel.

Reinstall screen in dryer.

Cleaning the dryer interior

To clean dryer drum

1. Apply a liquid, non ammable household cleaner to the

stained area of the drum and rub with a soft cloth until

stain is removed.

2. Wipe drum thoroughly with a damp cloth.

3. Tumble a load of clean cloths or towels to dry the drum.

NOTE: Garments that contain loose dyes, such as denim

blue jeans or brightly colored cotton items, may discolor the

dryer interior. These stains are not harmful to your dryer and

will not stain future loads of clothes. Dry these items inside

out to avoid drum staining.

Removing accumulated lint

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often,

depending on dryer usage. Cleaning should be done

by a quali ed servicer.

From the Exhaust Vent

Lint should be removed every 2 years, or more often,

depending on dryer usage.

Cleaning the dryer location

Vacation, storage, and moving care

Non-Use or Storage Care

Operate your dryer only when you are at home. If you will

be on vacation or not using your dryer for an extended

period of time, you should:

1. Unplug dryer or disconnect power.

2. (For gas dryers only): Close shut-off valve to gas supply

line.

3. Clean lint screen. See “Cleaning the Lint Screen.”

Moving Care

For power supply cord-connected dryers:

1. Unplug the power supply cord.

2. Make sure leveling legs are secure in dryer base.

3. Use tape to secure dryer door.

For direct-wired dryers:

1. Turn off power at fuse or breaker box.

2. Disconnect wiring.

3. Make sure leveling legs are secure in dryer base.

4. Use tape to secure dryer door.

For gas dryers:

1. Unplug or disconnect power to dryer.

2. Close shut-off valve in gas supply line.

3. Disconnect gas supply line pipe and remove  ttings

attached to dryer pipe.

4. Cap the open fuel supply line.

5. Make sure leveling legs are secure in dryer base.

6. Use tape to secure dryer door.

Reinstalling the Dryer

Follow the “Installation Instructions” to locate, level,

and connect the dryer.

Changing the drum light

(on some models)

1. Unplug dryer or disconnect power.

2. Open the dryer door. Locate the light bulb cover on the

back wall of the dryer. Using a Phillips-head screwdriver,

remove the screw located in the lower right-hand corner

of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with

a 10-watt appliance bulb only. Replace the cover and

secure with the screw.

4. Plug into a grounded outlet or reconnect power.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

Troubleshooting

Door not closed completely. Make sure the dryer door is closed completely.

Household fuse is blown or circuit

breaker has tripped.

Electric dryers use 2 household fuses or circuit breakers. The

drum may be turning, but you may not have heat. Replace both

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

Dryer will not run

PUSH to START knob not pressed

 rmly or held long enough.

Incorrect power supply.

Electric dryers require 240-volt power supply.

Check with a quali ed electrician.

Wrong type of fuse.

Use a time-delay fuse.

Unusual sounds

Dryer had a period of non-use.

If the dryer hasn’t been used for awhile, there may be a

thumping sound during the  rst few minutes of operation.

Check the front and rear edges of the drum for small objects.

Clean out pockets before laundering.

The four legs are not installed, or the

dryer is not level front to back and

side to side.

The dryer may vibrate if not properly installed.

See Installation Instructions.

A coin, button, or paper clip is

caught between the drum and front

or rear of the dryer.

Clothing knotted or balled up.

When balled up, the load will bounce, causing the dryer to

vibrate. Separate the load items and restart the dryer.

Press and hold the PUSH to START knob until you hear the dryer

drum moving.

No heat

Household fuse is blown or circuit

breaker has tripped.

The drum may be turning, but you may not have heat. Electric

dryers use 2 household fuses or circuit breakers. Replace both

fuses or reset the circuit breaker. If the problem continues, call

an electrician.

It is a gas dryer.

The gas valve clicking is a normal operating sound.

Supply line valve not open. For gas dryers, make sure the supply line valve is open.

Clothes are not drying

satisfactorily; drying

times are too long

Lint screen clogged with lint. Lint screen should be cleaned before each load.

Fluff Air cycle or No Heat temperature

setting has been selected.

Select the right cycle for the types of garments being dried.

See “Cycle Guide.”

Load too large and heavy to dry

quickly.

Separate the load to tumble freely.

Exhaust vent or outside exhaust

hood clogged with lint, restricting

air movement.

Run the dryer for 5-10 minutes. Hold your hand under the

outside exhaust hood to check air movement. If you do not feel

air movement, clean exhaust system of lint or replace exhaust

vent with heavy metal or  exible metal vent. Make sure vent is

not crushed or kinked. See Installation Instructions.

Exhaust vent diameter not the

correct size.

Use 4" (102mm) diameter vent material.

Dryer located in a room with

temperature below 45ºF (7ºC).

Proper operation of dryer cycles requires temperatures above

45ºF (7ºC).

Dryer located in a closet without

adequate opening.

Closet doors must have ventilation openings at the top and

bottom of the door. The front of the dryer requires a minimum

of 1" (25mm) of airspace and, for most installations, the rear

of the dryer requires 5" (127mm). See Installation Instructions.

Exhaust vent not the correct length.

Check that the exhaust vent is not too long or has too many

turns. Long venting will increase drying times. Make sure vent

is not crushed or kinked. See Installation Instructions.

Fabric softener sheets blocking

the grille.

Use only one fabric softener sheet, and use it only once.

Incorrect power supply.

Electric dryers require 240-volt power supply.

Check with a quali ed electrician.

First try the solutions suggested here or visit our website at www.whirlpool.com/product_help -

In Canada www.whirlpool.ca for assistance and to possibly avoid a service call.

If you experience

Possible Causes

Solution

Troubleshooting

Cycle time too short

Automatic cycle ending early. The load may not be contacting the sensor strips.

Level the dryer.

Use Timed Dry for very small loads. Change the Dry Level

setting on ACCUDRY™/Automatic Dry cycles.

Increasing or decreasing the Dry Level setting will change the

amount of drying time in a cycle.

Lint on load

Lint screen clogged.

Lint screen should be cleaned before each load.

Stains on load or drum

Dryer fabric softener not properly

used.

Add dryer fabric softener sheets at the beginning of the cycle.

Fabric softener sheets added to a partially dried load can stain

your garments.

Drum stains are caused by dyes in clothing (usually blue jeans).

These will not transfer to other clothing.

Loads are wrinkled

Load not removed from dryer at the

end of the cycle.

Select Wrinkle Shield™ feature to tumble the load without heat

to avoid wrinkling.

Dryer tightly packed.

Dry smaller loads that can tumble freely reduce wrinkles from

forming.

Odors

You have recently been painting,

staining, or varnishing in the area

where your dryer is located.

If so, ventilate the area. When the odors or fumes are gone

from the area, rewash and dry the clothing.

The electric dryer is being used for

the  rst time.

The new electric heating element may have an odor. The odor

will be gone after the  rst cycle.

Load is too hot

Laundry items removed from the

dryer before the end of the cycle.

Allow Cool Down cycle to  nish before removing laundry from

dryer. All cycles are cooled slowly to reduced wrinkling and

make it easier to handle. Items removed before Cool Down

may feel very warm.

A high temperature cycle was used,

or a separate temperature control

was set on High.

Select a lower temperature and use an automatic drying cycle.

These cycles sense the temperature or the moisture level in the

load and shut off when the load reaches the selected dryness.

This reduces overdrying.

WHIRLPOOL

LAUNDRY

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS

REQUIRED TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

Name, address, and telephone number

Model number and serial number

A clear, detailed description of the problem

Proof of purchase including dealer or retailer name and address

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR

A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces

do not allow limitations on the duration of implied warranties of merchantability or tness, so this limitation may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.

WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This

warranty gives you specic legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the

representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes

with this major appliance, you should ask Whirlpool or your retailer about buying an extended warranty.

11/14

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some questions can be

addressed without service. Please take a few minutes to review the Troubleshooting or Problem Solver section of the Use and

Care Guide, or visit https://www.whirlpool.com/product_help.

2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers. In the U.S. and Canada, direct all

requests for warranty service to:

Whirlpool Customer eXperience Center

In the U.S.A. call 1-800-253-1301. In Canada call 1-800-807-6777.

If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.

ONE YEAR LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,

operator, or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes, or correction of household electrical or

plumbing (i.e. house wiring, fuses, or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation solutions, etc.).

Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.

6. Conversion of your product from natural gas or propane gas or reversal of appliance

doors.

7. Damage from accident, misuse, abuse, fire, floods, acts of God, or use with products not

approved by Whirlpool.

8. Repairs to parts or systems to correct product damage or defects caused by unauthorized

service, alteration, or modification of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to appliance

finishes unless such damage results from defects in materials and workmanship and is

reported to Whirlpool within 30 days.

10. Discoloration, rust, or oxidation of surfaces resulting from caustic or corrosive

environments, including but not limited to, high salt concentrations, high moisture or

humidity, or exposure to chemicals.

11. Pick-up or delivery. This product is intended for in-home repair.

12. Travel or transportation expenses for service in remote locations where an authorized

Whirlpool servicer is not available.

13. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim, decorative

panels, flooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing,

removal, or replacement of the product.

14. Service or parts for appliances with original model/serial numbers removed, altered, or not

easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

For one year from the date of purchase,

when this major appliance is installed,

operated, and maintained according

to instructions attached to or furnished

with the product, Whirlpool Corporation

or Whirlpool Canada LP (hereafter

“Whirlpool”) will pay for Factory

Specified Replacement Parts and repair

labor to correct defects in materials or

workmanship that existed when this major

appliance was purchased, or at its sole

discretion replace the product. In the event

of product replacement, your appliance

will be warranted by the remaining term of

the original unit’s warranty period.

YOUR SOLE AND EXCLUSIVE REMEDY

UNDER THIS LIMITED WARRANTY

SHALL BE PRODUCT REPAIR AS

PROVIDED HEREIN. Service must be

provided by a Whirlpool designated

service company. This limited warranty

is valid only in the United States or

Canada and applies only when the major

appliance is used in the country in which

it was purchased. This limited warranty

is effective from the date of original

consumer purchase. Proof of original

purchase date is required to obtain service

under this limited warranty.

Sécurité de la sécheuse

– Ne pas entreposer ou utiliser de l’essence ou d’autres vapeurs ou liquidesinflammables

à proximité de cet appareil ou de tout autre appareil électroménager.

– QUE FAIRE DANS LE CAS D’UNE ODEUR DE GAZ :

•

Ne pas tenter d’allumer un appareil.

•

Ne pas toucher à un commutateur électrique; ne pas utiliser le téléphone se trouvant

sur les lieux.

•

Évacuer tous les gens de la pièce, de l’édifice ou du quartier.

•

Appeler immédiatement le fournisseur de gaz d’un téléphone voisin. Suivre ses

instructions.

•

À défaut de joindre votre fournisseur de gaz, appeler les pompiers.

– L’installation et l’entretien doivent être effectués par un installateur qualifié, uneagence

de service ou le fournisseur de gaz.

AVERTISSEMENT :

RISQUE D'INCENDIE OU D'EXPLOSION

Le non-respect des avertissements de sécurité peut causer des dommages à la propriété,

des blessures graves, voire la mort.

Véri cation d’une circulation d’air adéquate

pour le système d’évacuation

Maintenir une bonne circulation d’air

en effectuant les opérations suivantes :

Nettoyer le  ltre à charpie avant chaque charge.

Remplacer le matériau de conduits d’évacuation en

plastique ou en aluminium par des conduits d’évacuation

lourds et rigides de 4" (102 mm) de diamètre.

Toujours employer les conduits d’évacuation les plus

courts possible.

Ne pas utiliser plus de quatre coudes à 90° dans un

circuit d’évacuation car chaque inclinaison et courbe

réduit le  ux d’air.

Retirer la charpie et les résidus du clapet d’évacuation.

Retirer la charpie sur toute la longueur du circuit

d’évacuation au moins tous les 2 ans. Après le

nettoyage, veuillez suivre les instructions d’installation

fournies avec la sécheuse pour une véri cation  nale

de l’appareil.

Dégager tout article qui se trouverait devant la sécheuse.

Circulation d’air adéquate

Une sécheuse a besoin de chaleur et d’une circulation

d’air adéquate pour sécher ef cacement le linge. Une

ventilation adéquate réduit les durées de séchage et accroît

les économies d’énergie. Voir les Instructions d’installation.

Le système d’évacuation  xé à la sécheuse joue un rôle

important dans la circulation de l’air.

Les interventions de dépannage causées par une ventilation

incorrecte ne sont pas couvertes par la garantie et seront

à la charge du client, quel que soit l’installateur de la

sécheuse.

Utiliser les programmes de séchage automatique ACCUDRY™ pour que la sécheuse puisse réaliser davantage d’économies

d’énergie et apporter un soin supérieur aux tissus. Durant les programmes de séchage automatique ACCUDRY™, la température

de séchage de l’air et le niveau d’humidité sont détectés dans la charge. Cette détection se produit tout au long du programme

de séchage et la sécheuse s’éteint lorsque la charge atteint le degré de séchage sélectionné.

Avec l’option de séchage minuté, la sécheuse fonctionne pendant la durée réglée, ce qui peut parfois entraîner le rétrécissement

ou le froissement du linge, et l’accumulation d’électricité statique due au séchage excessif. Utiliser le séchage minuté pour une

charge encore humide nécessitant un peu de temps supplémentaire ou lorsqu’on utilise la grille de séchage.

Bon

Mieux

Utilisation des programmes automatiques ACCUDRY™ pour

un meilleur soin du tissu et davantage d’économies d’énergie

Tableau de commande et caractéristiques

Caractéristique Wrinkle Shield™

(sur certains modèles)

Lorsqu’on ne peut pas enlever une charge de la sécheuse

dès qu’elle s’arrête, des faux plis peuvent se former. La

caractéristique Wrinkle Shield™ effectue un culbutage

de la charge, la réagence et l’aère à intervalles réguliers

pour aider à éviter la formation de faux plis.

Obtener 90 minutes de culbutage périodique

sans chaleur à la n d’un programme. Appuyer

sur le bouton Wrinkle Shield™ pour activer

ou désactiver cette fonction à tout moment

avant la n d’un programme.

BOUTON DE PROGRAMME DE LA SÉCHEUSE

Utiliser le bouton de programme de séchage pour

sélectionner les programmes disponibles sur la sécheuse.

Tourner le bouton de programme pour sélectionner un

programme correspondant à la charge de linge. Voir “Guide

de programmes” pour des descriptions de programmes

détaillées.

Séchage minuté

Ceci fait fonctionner la sécheuse pour la durée

spéciée sur le module de commande. Pour les modèles

dotés d’un bouton de sélection de température, vous

pouvez choisir un réglage en fonction des tissus de

votre charge. Le temps de séchage et la température

dépendront du modèle de votre sécheuse.

Programmes automatiques

avec la caractéristique ACCUDRY™

Détecte l’humidité de la charge et la température de l’air

et s’éteint lorsque la charge a atteint le degré de séchage

sélectionné. Permet d’obtenir le meilleur rendement de

séchage en un minimum de temps. Le temps de séchage

variera en fonction du type de tissu, du volume de la

charge et du réglage de séchage.

TEMPERATURE (température)

Choisir une température de séchage en fonction des

tissus de votre charge. Si vous hésitez sur la température à

sélectionner pour une charge donnée, choisir le réglage plus

bas plutôt que le réglage plus élevé.

REMARQUE : Le réglage No Heat (sans chaleur) (sur

certains modèles) n’est pas disponible sur les programmes

de séchage automatique ACCUDRY™.

CYCLE SIGNAL/PUSH to START (signal de

programme/enfoncer pour mettre en marche)

Le signal de n de programme émet un signal sonore

qui indique la n du programme de séchage. Le fait de

sortir rapidement les vêtements à la n du programme

permet de réduire le froissement.

Tourner le bouton Cycle Signal (signal de programme)

pour activer ou désactiver le réglage désiré. Appuyer sur le

bouton PUSH to START (enfoncer pour mettre en marche)

pour mettre la sécheuse en marche.

REMARQUE : Lorsque le réglage Wrinkle Shield™ est

sélectionné et que le signal de programme est activé,

un signal sonore retentit toutes les 5 minutes jusqu’à

ce que les vêtements soient retirés, ou que le réglage

Wrinkle Shield™ se termine.

Certains programmes et options ne sont pas disponibles sur certains modèles. L’apparence des appareils peut varier.

2 31 4

2 3 4

Articles à sécher :

Température :

Options

disponibles :

Détails du programme :

Energy Preferred

Delicate (articles

délicats) ou Less

Dry (moins sec)

Wrinkle Shield™

Temperature

Cycle Signal

Guide de programmes – Séchage minuté

Articles à sécher :

Programme : Température :

Options

disponibles :

Détails du programme :

Certains programmes et réglages ne sont pas disponibles sur certains modèles.

Articles lourds ou

volumineux tels que

serviettes épaisses

ou peignoirs

N’importe quelle

charge

Heavy Dry

ou Heavy Duty

Damp Dry

N’importe laquelle

Temperature

Sélectionner high (élevé) pour sécher des

charges importantes ou lourdes.

Sèche les articles à un degré d’humidité

ou les articles qui ne nécessitent pas un

programme de séchage complet.

REMARQUE : Si les charges ne semblent pas aussi sèches que désiré, sélectionner More Dry (plus sec) ou Very Dry (très sec)

la prochaine fois que l’on sèche une charge semblable. Si les charges semblent plus sèches que désiré, sélectionner Less Dry

(moins sec) la prochaine fois que l’on sèche une charge semblable.

Tout-aller, chemisiers,

pantalons, articles légers,

synthétiques, tissus

délicats, vêtements de

sport

N’importe laquelle

Wrinkle Shield™

Temperature

Cycle Signal

Réglage de la température de séchage

Si la sécheuse comporte plusieurs réglages de chaleur :

On peut utiliser un réglage de chaleur High (élevée) pour

sécher les articles lourds tels que les serviettes et les

vêtements de travail.

Un réglage de chaleur Low (bas) à Medium (moyen) peut être

utilisé pour sécher les articles moyennement lourds tels que

draps, chemisiers, robes, sous-vêtements, tissus à pressage

permanent et certains tricots.

Utiliser le réglage No Heat (sans chaleur) pour la mousse, le

caoutchouc, le plastique ou les tissus sensibles à la chaleur.

Sécher sur une corde à linge les tissus doublés ou

multicouches.

REMARQUE : Pour toute question concernant les

températures de séchage pour diverses charges, consulter

les instructions sur l’étiquette de soin.

Jeans, vêtements de travail

lourds, serviettes

Jeans, More ou

Very Dry

(très sec, plus sec

ou très sec)

Wrinkle Shield™

Temperature

Cycle Signal

Permet d’obtenir le meilleur rendement de

séchage en un minimum de temps. Le temps

de séchage variera en fonction du type de

tissu, du volume de la charge et du réglage

de séchage.

Choisir une température de séchage en

fonction des tissus de votre charge. Si vous

hésitez sur la température à sélectionner pour

une charge donnée, choisir le réglage le plus

bas plutôt que le réglage le plus élevé.

Programme :

High

(élevé)

Medium

(moyen)

Low

(bas)

Vêtements de travail,

articles moyennement

lourds, draps

Caoutchouc, plastique,

tissus sensibles à la

chaleur

Fluff Air

No Heat

(sans chaleur)

Temperature

Séchage sans chaleur.

Options de Température

de séchage :

Very Dry (très sec)

Energy Preferred (éconergique)

Less Dry (moins sec)

Heavy Dry (séchage intense)

Heavy Duty (service intense)

Options disponibles :

Temperature (température)

Wrinkle Shield™ (antifroissement)

Cycle Signal (signal de programme)

Time Adjustment (ajustement de la durée)

Damp Dry (séchage humide)

Tumble Press (pressage par culbutage)

Fluff Air (duvetage à l’air)

ou Normal

TIMED DRY (séchage minuté) – Fait fonctionner la sécheuse pour la durée spécifi ée sur le module de commande.

Guide de programmes – ACCUDRY™/Programmes automatiques

Certains programmes et réglages ne sont pas disponibles sur certains modèles.

SÉCHAGE AUTOMATIQUE ACCUDRY™ – Détecte l’humidité présente dans la charge ou la température de l’air et s’éteint

lorsque la charge atteint le degré de séchage sélectionné.

REMARQUE : Les certifications énergétiques gouvernementales pour les modèles Whirlpool Gas et Electric étaient basées sur le

cycle Timed Dry avec le réglage de température de séchage maximum. Les paramètres par défaut tels que Auto Dry, Normal,

Low Heat, Wrinkle Shield n'ont pas été utilisés.

Utilisation de la sécheuse

1. Nettoyer le  ltre à charpie

Nettoyer le  ltre à charpie avant chaque charge. Retirer le

 ltre à charpie de son logement. Enlever la charpie du  ltre

en la roulant avec les doigts. Ne pas rincer ni laver le  ltre

pour enlever la charpie. Remettre le  ltre à charpie fermement

en place.

Pour plus d’informations sur le nettoyage, voir “Entretien

de la sécheuse”.

2. Charger la sécheuse

Placer le linge dans la sécheuse. Fermer la porte.

REMARQUE : La porte de votre modèle peut différer de celle

 gurant sur l’illustration. Certains modèles peuvent comporter

des portes à ouverture vers le bas.

Ne pas surcharger la sécheuse; les vêtements doivent pouvoir

culbuter librement.

AVERTISSEMENT : Pour réduire le risque d’incendie, de choc

électrique ou de blessures à autrui, lire les IMPORTANTES

INSTRUCTIONS DE SÉCURITÉ avant de faire fonctionner cette

sécheuse.

Avant d’utiliser la sécheuse, essuyer le tambour de la sécheuse

avec un linge humide pour enlever la poussière accumulée au

cours de l’entreposage et de l’expédition.

4. Sélectionner les réglages

et options du programme

Sélectionner les réglages et options du programme

en tournant le bouton sur la position souhaitée.

REMARQUE : Tous les réglages et options ne sont pas

disponibles avec tous les programmes.

Temperature (température)

Tourner le bouton Temperature (température) pour modi er

le réglage de la température de séchage. Voir “Réglage de

la température de séchage”.

Caractéristique Wrinkle Shield™ (antifroissement)

(sur certains modèles)

Obtener 90 minutes de culbutage périodique sans chaleur

à la  n d’un programme. Tourner le bouton Wrinkle Shield™

pour activer ou désactiver cette fonction à tout moment

avant la  n d’un programme.

Sur les modèles dotés de l’option Wrinkle Shield™

(antifroissement), le programme ajoute automatiquement

40 minutes de culbutage périodique sans chaleur à la  n

d’un programme.

3. Sélectionner le programme désiré

5. Sélectionner le signal

de programme (si désiré)

Tourner le bouton Cycle Signal (signal de programme)

pour activer ou désactiver le signal. Le signal de programme

est un signal sonore qui retentit lorsque le programme de

séchage est terminé. Sortir rapidement les vêtements à la  n

du programme réduit le froissement.

REMARQUE : Lorsque le réglage Wrinkle Shield™ est

sélectionné et que le signal de programme est activé, un

signal sonore retentit toutes les 5 minutes jusqu’à ce que les

vêtements soient retirés, ou que le réglage Wrinkle Shield™

se termine.

Le tableau de commande et les programmes peuvent varier selon le modèle.

Sélectionner le programme souhaité pour la charge.Voir le

Guide de programmes pour plus d’informations sur chaque

programme.

Programmes de séchage automatique/ACCUDRY™

Selon votre charge, vous pouvez sélectionner un degré

de séchage différent en tournant le bouton sur le degré

de séchage.

Lorsqu’on sélectionne More or Very Dry (plus sec ou très

sec), Normal, ENERGY PREFERRED (éconergique) ou Less

Dry (moins sec), le degré de séchage qui commandera l’arrêt

de la sécheuse est automatiquement ajusté. Après avoir

sélectionné un certain degré de séchage, il est impossible de

le modi er sans arrêter le programme.

Les programmes de séchage automatique/ACCUDRY™

offrent un séchage idéal en un minimum de temps. La durée

de séchage varie en fonction du type de tissu, de la taille de

la charge et du réglage de niveau de séchage.

REMARQUE : Le séchage More or Very Dry (plus sec ou très

sec) élimine davantage d’humidité dans la charge. ENERGY

PREFERRED ou Normal est utilisé comme point de départ

dans les programmes ACCUDRY™. Le séchage Less Dry

(moins sec) élimine moins d’humidité et est utilisé pour les

charges que l’on souhaite placer sur un cintre pour qu’elles

nissent de sécher.

La page charge ...

Whirlpool WED4950HW Manuel utilisateur

Marque: Whirlpool

Modèle: WED4950HW

Catégorie: Sèche-linge

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WED4950HW User manual

Documents connexes

Autres documents

Maytag MEDC700VW - Centennial Series-27 Inch Electric Dryer User Instructions