LG WD100CV Le manuel du propriétaire

ENGLISH

FRANÇAIS

OWNER’S MANUAL

WASHING

MACHINE

Read this owner’s manual thoroughly before operating the appliance and

keep it handy for reference at all times

www.lg.com

WD100C*

WD200C*

MFL68267007

MFL68267007_E.indd 1 17. 1. 19. 오후 6:52

2

TABLE OF CONTENTS

3 IMPORTANT SAFETY INSTRUCTIONS

3 Basic Safety Precautions

4 Grounding Requirements

5 Safety Instructions for Installation

6 Safety Instructions for Use, Care, Cleaning and

Disposal

7 FEATURES AND BENEFITS

7 Key Parts and Components

7 Included Accessories

7 Required Accessories

8 INSTALLATION INSTRUCTIONS

8 Choose the Proper Location

8 Power Outlet

8 Flooring

9 Unpacking and Removing Shipping Material

1 0 Overview of Connections

11 Connecting the Water Lines

12 Connecting the Drain Hose

12 Using The Drain Connector

13 Leveling the Washing Machine

14 Connecting to the Power Supply

15 Sorting Wash Loads

16 Detergent and Dispenser Use

17 HOW TO USE

17 Control Panel Features

1 8 Time and Status Display

19 Operating the Washer

20 Cycle Guide

20 Wash Cycles

21 Options

21 Warm Water

21 Extra Rinse

21 Child Lock

22 CARE AND CLEANING

22 Regular Cleaning

22 Cleaning the Exterior

22 Care and Cleaning of the Interior

22 Tub Clean Cycle

22 Removing Mineral Buildup

22 Leave the Lid Open

23 Maintenance

24 SPECIFICATIONS

24 SMART DIAGNOSIS™ SYSTEM

25 TROUBLESHOOTING

25 Faqs: Frequently Asked Questions

26 Normal Sounds You May Hear

26 Before Calling for Service

30 Error Codes

32 WARRANTY

MFL68267007_E.indd 2 17. 1. 19. 오후 6:52

3

ENGLISH

SAFETY MESSAGES

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or

electric shock, or to prevent property damage, injury to persons, or death. Your safety and the safety of

others is very important. There are many important safety messages in this manual and on your appliance.

Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in prop-

erty damage and/or serious bodily harm or death.

All safety messages will follow the safety alert symbol and either the word WARNING or

CAUTION. These words mean:

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury,

and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

You can be killed or seriously injured if you don’t follow instructions.

You may be slightly injured or cause damage to the product if you do not follow

instructions.

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic pre-

cautions, including the following.

y Use this appliance only for its intended purpose as described in this Owner's Manual.

y Before use, the washer must be properly installed as described in this manual.

y Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gaso-

line, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that

could ignite or explode.

y Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash

water. These substances give off vapors that could ignite or explode.

y Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used

for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for

such a period, before using the washer, turn on all hot water faucets and let the water flow from each

for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not

smoke or use an open flame during this time.

y Do not allow children to play on or in the washer. Close supervision of children is necessary when the

washer is used near children. A child might become trapped inside the washer and suffocate.

y Before the washer is removed from service or discarded, remove the lid to prevent children from

climbing inside.

y Do not install or store the washer where it will be exposed to the weather or freezing temperatures.

y Do not tamper with controls.

y Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags,

etc.), gasoline, chemicals and other flammable vapors and liquids.

y Service must be performed by a qualified service technician. Do not disassemble the washer.

y See Installation Instructions for grounding requirements.

y WARNING : This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm. Wash hands after handling.

y ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

y Do not place items exposed to cooking oil in your washer. Items contaminated with cooking oils may

contribute to a chemical reaction that could cause a load to catch fire.

BASIC SAFETY PRECAUTIONS

WARNING

CAUTION

MFL68267007_E.indd 3 17. 1. 19. 오후 6:52

4

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion or

electric shock, or to prevent property damage, injury to persons, or death.

GROUNDING REQUIREMENTS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. This appliance is equipped with

a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

CERTAIN INTERNAL PARTS ARE INTENTIONALLY NOT GROUNDED AND MAY PRESENT A RISK

OF ELECTRIC SHOCK ONLY DURING SERVICING. SERVICE PERSONNEL - DO NOT CONTACT THE

FOLLOWING PARTS WHILE THE APPLIANCE IS ENERGIZED: PUMP, VALVE, MOTOR, CONTROL.

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Check with

a qualified electrician or servicer if you are in doubt as to whether the appliance is properly grounded. Do

not modify the plug provided with the appliance. If it does not fit the outlet, have a proper outlet installed

by a qualified electrician. Failure to follow these warnings can cause serious injury, fire, electric shock, or

death.

y Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

y This washer is not designed for maritime use or for mobile installations such as in RVs, aircraft, etc.

y Turn off the water faucets and unplug the washer if the machine is to be left for an extended period of

time, such as during vacations.

y Do not use to dry articles containing foam rubber or similarly textured rubber-like materials.

y Packaging material can be dangerous for children. There is a risk of suffocation! Keep all packaging from

children.

y Always check the inside of the washer for foreign objects before loading laundry. Keep the lid closed

when not in use.

y Do not reach into the appliance if the tub or agitator is moving.

y In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area immediately. Do not

turn any appliance or light on or off. Do not use a ventilating fan. A spark may result in an explosion or

fire.

y Do not repair or replace any part of the appliance or attempt any servicing unless specifically recom-

mended in the user-maintenance instructions or in published user-repair instructions that you under-

stand and have the skills to carry out.

WARNING

MFL68267007_E.indd 4 17. 1. 19. 오후 6:52

5

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

To reduce the risk of fire, electric shock or injury to persons when using this appliance, follow basic precautions,

including the following:

y Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions are

packed with the washer for installer’s reference. If the washer is moved to a new location, have it checked

and reinstalled by a qualified service technician. Failure to follow this warning can cause serious injury, fire,

electric shock, or death.

y The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.

y Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to

follow this warning can cause serious injury, fire, electric shock, or death.

y For personal safety, this appliance must be properly grounded. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

y This washer must be plugged into a 120 VAC, 60 Hz grounded outlet. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

y Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

y Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have

it replaced with a properly grounded 3-prong wall outlet. Failure to follow this warning can cause serious

injury, fire, electric shock, or death.

y Do not install on carpet. Install washer on a solid floor. Failure to follow this warning can cause serious leak

damage.

y The washer should always be plugged into its own individual electrical outlet which has a voltage rating that

matches the rating plate. This provedes the best performance and also prevents overloading house wiring

circuits which could cause a fire hazard from overheated wires.

y If installing the pedestal washer with an LG front-loading washer and an LG gas dryer, and insufficient outlets

are available, an extension cord rated at no less than the branch circuit may be used.

y Never unplug your washer by pulling on the power cord. Always grip plug firmly and pull straight out from the

outlet. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

y Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

y When installing or moving the washer, be careful not to pinch, crush, or damage the power cord. Failure to

follow this warning can cause serious injury, fire, electric shock, or death.

y The washer must be installed and electrically grounded by a qualified service person in accordance with local

codes to prevent shock hazard and assure stability during operation.

y The washer is heavy. Two or more people may be needed to install and move the appliance. Failure to do so

can result in back or other injury.

y Store and install the washer where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause serious leak damage.

y To reduce the risk of electric shock, do not install the washer in humid spaces. Failure to follow this warning

can cause serious injury, fire, electric shock, or death.

y To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the

use of long sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could

result in property damage, injury to persons or death.

y Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

y To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the

washer at the household distribution panel by removing the fuse or switching off the circuit breaker before

attempting any maintenance or cleaning.

y Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor. If

you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be

damaged and this may result in electric shock or fire.

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion,

or electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

MFL68267007_E.indd 5 17. 1. 19. 오후 6:52

6

IMPORTANT SAFETY INSTRUCTIONS

For your safety, the information in this manual must be followed to minimize the risk of fire, explosion, or

electric shock, or to prevent property damage, injury to persons, or death.

y The pedestal washer is for installation and use only underneath an LG manufactured front-loading washer.

The pedestal washer is not designed to operate as a standalone unit, under an LG top-loading washer, under

a dryer, or under a non-LG manufactured washer.

y Do not tamper with the stacking switch. Doing so may cause machine malfunctions or serious injury.

y Do not operate the pedestal washer with two or more pedestal washers stacked. Doing so may cause

machine malfunctions or serious injury.

SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING AND DISPOSAL

To reduce the risk of fire, electric shock or injury to persons when using this appliance, follow basic precautions,

including the following:

y Unplug the washer before cleaning to avoid the risk of electric shock.

y Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the finish.

y Do not put oily or greasy rags or clothing on top of the washer. These substances give off vapors that could

ignite the materials.

y Do not wash items that are soiled with vegetable or cooking oil. These items may contain some oil after laun-

dering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

y Disconnect this appliance from the power supply before attempting any user maintenance. Turning the

controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow this

warning can cause serious injury, fire, electric shock, or death.

y Do not combine laundry products for use in one load unless specified on the label.

y Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using

laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

y Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, press the

START/PAUSE button and allow the drum to coast to a complete stop before reaching inside. Failure to follow

this warning can cause serious injury, fire, electric shock, or death.

y Do not allow children to play on or in the washer. Close supervision of children is necessary when the

washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to

comply with these warnings could result in serious injury to persons or death.

y Destroy the carton, plastic bag, and other packing materials after the washer is unpacked. Children might

use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.

Failure to comply with these warnings could result in serious injury to persons or death.

y Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on product

labels. Failure to comply with these warnings could result in serious injury to persons or death.

y Remove the lid to the washing compartment before your washer is removed from service or discarded to

avoid the danger of children or small animals getting trapped inside. Failure to do so can result in serious

injury to persons or death.

y Keep hands and foreign objects clear of the lid and latch area when closing the lid. Failure to keep hands clear

can result in personal injury.

y Do not touch the power plug with wet hands. This may result in electric shock.

y Do not touch the water draining from the machine during a high-temperature wash or drying cycle. This

water is hot, and touching it may result in burns or injury.

y Do not stand on top of the appliance or place objects(such an laundry, lighted candles,lighted cigarettes,

dishes, chemicals, metal objects, etc.) on the appliance. This may result in electric shock, fire, problems with

the product, or injury.

y Do not install or store the washer where it will be exposed to freezing temperatures. Water may freeze in

the hoses and damage the washer. Winterize the washer before storing or moving it in freezing tempera-

tures. Refer to the Maintenance section for instructions.

y To avoid breaking the lid glass, do not push too hard on the lid when closing.

y Do not step on the pedestal washer. Doing so may damage the washer or cause serious injury.

WARNING

MFL68267007_E.indd 6 17. 1. 19. 오후 6:52

7

ENGLISH

FEATURES AND BENEFITS

KEY PARTS AND COMPONENTS

A INVERTER DIRECT DRIVE MOTOR

The inverter motor, which is directly connected to the tub, produces less noise and vibration while

offering outstanding durability and a long lifespan.

B COMPACT CAPACITY & NEVERUST™ STAINLESS STEEL TUB

The efﬁcient design provides capacity in a compact space.

C FRONT TOUCH PANEL

The simple LED display shows cycle options, setting, cycle status and estimated time remaining.

The touch buttons offer more convenience and a premium design aesthetic.

D SMART DIAGNOSIS™

If you ever experience an issue with your LG washer, you don’t have to worry.

The SmartDiagnosis™ feature helps the service center diagnose problems over the phone, or with a

simple app on your smart phone, helping you minimize costly, inconvenient service calls.

E REMOTE CONTROL RCW1 (OPTIONAL)

Don't want to bend down to reach the controls? Set cycles with the touch of a button on the

optional remote control (available online or through an LG retailer).

NOTE: Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are

missing or to purchase accessories. For a list of LG front-loading washers which are compatible with the

pedestal washer, visit the LG website at www.lg.com/us/twinwash

Drawer

Lid

Control panel

Leveling feet

Leg Support

Stacking Switch

Top Cover

INCLUDED ACCESSORY

2 Inlet

Hoses-Short

2 Inlet Hose

Y-Connectors

Drain Hose

Y-Connector

Drain Hose Non-Skid Pads

(18EA)

(5EA)

Max load

(2 tsp., 10 g)

Normal

(1 tsp., 5 g)

2 Inlet Hoses

Wrench 2 Tie Straps

3 Band clamp

Screws Detergent Dispenser

MFL68267007_E.indd 7 17. 1. 19. 오후 6:52

8

INSTALLATION INSTRUCTIONS

CHOOSE THE PROPER LOCATION

y This pedestal washer must be installed underneath

a matching front-loading LG washing machine manu-

factured after 2009. (The 29" wide machine must be

stacked under a 29" wide LG front-loading washer. The

27" wide machine must be stacked under a 27" wide

LG front-loading washer.)

y The pedestal washer will not work as a standalone unit.

y The pedestal washer must be stacked under an LG

brand appliance in order to operate properly.

CAUTION

POWER OUTLET

y The power outlet must be within 60 in. (1.5 m) of

either side of the washer.

y The appliance and outlet must be positioned so

that the plug is easily accessible.

y For best performance, plug the washer into its own

individual outlet. If necessary, use a new, UL-listed

3-prong adapter or 3-wire extension cord with a 3-prong

(grounding) plug rated at no less than the branch circuit.

Do not use an extension cord longer than three feet.

Failure to follow these warnings can result in serious

injury, fire, electric shock, or death

y The outlet must be grounded in accordance with current

wiring electric codes and regulations.

y Time-delay fuse or circuit breaker is recommended.

WARNING

NOTE: It is the personal responsibility and obligation

of the product owner to have a proper outlet installed

by a qualified service technician.

To ensure sufficient clearance for water lines and airflow, allow

minimum clearances of at least 1 in. (2.5 cm) at the sides and

4 in. (10 cm) behind the unit. Be sure to allow for wall, door, or

floor moldings that may increase the required clearances.

FLOORING

y To minimize noise and vibration, the washer MUST be

installed on a solidly constructed floor.

y Allowable slope under the entire washer is a maximum 1

inch. difference from side to side or from front to back.

y Installing on carpeting and soft tile surfaces is not

recommended.

y Never install the washer on a platform or weakly supported

structure.

NOTE: The washer must be installed on firm flooring to minimize

vibration during the spin cycle. Concrete flooring is best, but a

wood floor is sufficient, provided it is built to FHA standards. The

washer should not be installed on rugs or exposed to weather.

Do not use a drip pan as it can block the drawer. Using the drip

pan may result in increased vibration and noise during operation.

y Two or more people are required when moving, unpack-

ing, and stacking the washer. Failure to follow this warning

may result in damage to property or serious bodily harm.

y Store and install the washer where it will not be exposed

to weather or to temperatures below freezing. Failure to

follow this warning can cause serious injury, fire, electric

shock, or death.

y Properly ground the washer to conform with all electric

governing codes and ordinances. Failure to follow this

warning can cause serious injury, fire, electric shock, or

death.

y To reduce the risk of electric shock, do not install the wash-

er in humid spaces. Failure to follow this warning can cause

serious injury, fire, electric shock, or death.

y To ensure proper air flow, do not block the large opening on

the bottom of the washer with carpeting or other materials.

y Do not remove the ground prong. Do not use a 2-prong

adapter or 2-wire extension cord. Failure to follow these

warnings can cause serious injury, fire, electric shock, or

death.

WARNING

50

1

/2" (128.3 cm)

52

3

/4" (134 cm)

(20 in. [50.8 cm] additional

needed for service)

29

3

/4" (75.6 cm)

32" (82.1 cm)

1”

(2.5 cm)

1”

(2.5 cm)

52

5

/16" (132.9 cm)

54

1

/4" (137.8 cm)

27" (68.9 cm)

29" (73.7 cm)

MFL68267007_E.indd 8 17. 1. 19. 오후 6:52

9

ENGLISH

INSTALLATION INSTRUCTIONS

UNPACKING AND REMOVING

SHIPPING MATERIAL

1. After removing the carton and shipping material,

lift the washer off the foam base. Make sure the

plastic tub support comes off with the base and

is not stuck to the bottom of the washer.

Plastic Tub

Support

Carton Base

If you must lay the washer down to remove the base

packaging materials, always protect the side of the

washer and lay it carefully on its side. DO NOT lay

the washer on its front or back.

2. Save the foam block for future use. If the washer

must be moved in the future, the foam block

will help prevent damage to the washer during

transportation.

NOTE: To prevent damage, do not remove

the foam block until the washer is at the final

location.

3. Turn the top cover about 180 degrees. Cover the

upper hole with the top cover and install 4 short

screws (included in packing box) to fix it in place.

Top cover

Short screws

y The top cover must be installed to avoid the risk of

electric shock or short circuit. Failure to do so can

cause serious injury, fire, electric shock or death.

WARNING

4. Make sure the leveling legs on the front-loading

washer are fully retracted before stacking it

on top of the pedestal washer. Position the

appliance on top of the pedestal washer.

Washer legs

5. Make sure the holes on the pedestal washer

align with the holes in the front-loading washer,

then install 4 long screws (included in box) at

each corner to securely attach the front-loading

washer to the pedestal washer.

Long screws

6. Extend the legs of the front-loading washer

slightly until it is snugged up against the pedestal

washer.

TOOLS YOU WILL NEED

y Adjustable Pliers • Carpenter's Level

y Screwdriver

MFL68267007_E.indd 9 17. 1. 19. 오후 6:52

10

INSTALLATION INSTRUCTIONS

CONNECTING THE DRAIN HOSE WITH

FULL-SIzE WASHER

1. Front-loading washer and pedestal washer with

dryer.

Tie Strap

Band clamps

2. Front-loading washer and pedestal washer with

hybrid dryer

Tie Strap

Band clamps

DETAIL VIEW OF DRAIN CONNECTOR

CONNECTION

For narrow standpipes, insert hybrid dryer drain hose in

center of drain connector. DO NOT insert dryer drain hose

further than 1 inch (2.5 cm). Use tie straps to keep hoses

in place.

OVERVIEW OF CONNECTIONS

CONNECTING THE WATER LINES WITH

FULL-SIzE APPLIANCES

1. Front-loading washer and pedestal washer with

dryer.

Cold

Hot

Short inlet hose

2. Front-loading washer and pedestal washer with

Turbo Steam dryer

Cold

Hot

Short inlet hose

Required for water inlet

Item Qty

Y-Connector 2

Short inlet hose 2

Long inlet hose 4

long inlet hoses sold separately

Required for water inlet

Item Qty

Y-Connector 3

Short inlet hose 3

Long inlet hose 5

long inlet hoses sold separately

Drain hose

Band clamps

Drain

Y Connector

MFL68267007_E.indd 10 17. 1. 19. 오후 6:52

11

ENGLISH

INSTALLATION INSTRUCTIONS

CONNECTING THE WATER LINES

NOTE:

• For your safety, and for extended product life,

use high-quality LG components. LG is not

responsible for product malfunction or damage

caused by the use of separately purchased non-

LG parts.

• Do not reuse old hoses. Use only new hoses

when installing the washing machine. Old hoses

could leak or burst causing flooding and property

damage. Contact LG Customer Service for

assistance in buying hoses: 1-800-243-0000.

• Do not use flood-preventing hoses with auto

shutoff devices. The devices can be tripped

during fill and prevent the machine from filling

properly.

1. Check the fittings and seals.

Inspect the threaded fitting on each hose and

make sure there is a rubber seal in place in both

ends of each hose to prevent leaking.

Rubber Seal

Water Hose

(to tap)

Water Hose

(to water inlet

on washer)

Rubber Seal

2. Connect the water supply hoses.

Connect the water supply hoses to the HOT and

COLD water faucets tightly by hand and then

tighten another 2/3 turn with pliers. Connect the

blue hose to a cold water faucet and the red hose

to a hot water faucet.

y

Do not overtighten.

Damage to the coupling

can result.

WARNING

Water Faucet

3. Flush out the inlet hoses.

After connecting the inlet hoses

to the water faucets, turn on the

water faucets to flush out foreign

substances (dirt, sand or sawdust)

in the water lines. Let water drain

into a bucket, and check the water

temperature to make sure you've

connected the hoses to the correct

faucets.

4. Attach the water lines to the back of the

washer.

Attach the hot water line to the provided inlet

Y-connector and attach the short water line

from the Y-connector to the full-size washer

inlet. Then attach the long water line from

the Y-connector to the pedestal washer inlet.

Repeat with

the cold water

connections.

Tighten the

fittings securely.

Turn on both

faucets all the

way and check for

leaks at both ends

of the hoses.

y

Do not overtighten the hoses or crossthread

y

the hose fittings.

Overtightening or cross-

threading can damage the valves, resulting in

leaking and property damage.

WARNING

NOTE:

• Periodically check the hoses for cracks, leaks,

and wear, and replace the hoses every five years.

Do not stretch the water hoses intentionally, and

make sure that they are not pinched, crushed or

kinked by other objects.

• Water supply pressure must be between 20

psi and 120 psi (138–827 kPa). If the water

supply pressure is more than 120 psi, a pressure

reducing valve must be installed.

• To provide optimum washing performance, set

the hot water temperature at 120°–135°F (48°–

57°C) and the cold at 60°F (15°C).

• Never install or store the washer in a location

subject to freezing temperatures. Damage to

the water lines and internal mechanisms of the

washer can result. If the washer was exposed to

freezing temperatures prior to installation, allow

it to stand at room temperature for several hours

before use and check for leaks prior to operation.

Hot water inlet

Cold water inlet

MFL68267007_E.indd 11 17. 1. 19. 오후 6:52

12

INSTALLATION INSTRUCTIONS

CONNECTING THE DRAIN HOSE

y The drain hose should always be properly secured.

Failure to properly secure the drain hose can result in

flooding and property damage.

y The drain must be installed in accordance with any

applicable local codes and regulations.

y Make sure that the drain hose is not stretched,

pinched, crushed, or kinked.

CONNECTING THE PEDESTAL WASHER DRAIN HOSE

1. Insert the band clamp (included in packing box) on

to the drain hose elbow.

Band Clamp

2. With the hose leading up from the elbow, insert

the elbow onto the drain outlet on the back of the

pedestal washer.

3. Adjust the band clamp with pliers to keep the hose

securely in place and prevent leaking.

Band Clamp

USING THE DRAIN CONNECTOR

y Connect the drain hose of the full-size washer and the

pedestal washer to the drain connector. Insert the included

band hose clamps on to the ends of the two drain hoses.

Push the drain hoses firmly onto the drain connector. Adjust

the band hose clamps to prevent the hoses from coming

loose or leaking. Failure to do so could result in flooding.

Use of the drain connector helps avoid siphoning, odors, or

improper draining.

OPTION 1: STANDPIPE

Bend the outlet end of the drain hoses to form a U shape.

Insert the end of the drain connector into the drain.

Use the

three tie straps included with the installation materials in the

foam block in the tub to secure the drain hoses to each other

and to the drain. See Overview of Connections for details.

If your drain is a standpipe, fasten the drain hoses to the

standpipe with the tie strap provided.

NOTE:

y Normal height of the end of the hoses should be

approximately 35”~47” (90~120 cm) from the floor.

y Do not install the end of the drain hoses lower than 29".

(73.7 cm) or higher than 96 in. (243.8 cm) above the

bottom of the washer or more than 60 in. (152.4 cm) away

from the washer.

y Never create an airtight seal between the hoses and the

drain with tape or other means. If no air gap is present,

water can be siphoned out of the tub resulting in poor

wash/rinse performance or clothing damage.

y For best performance, if there is an additional drain hose

from a hybrid dryer, place the drain hose in the standpipe

next to the drain connector.

y If the standpipe is too narrow to fit both the drain connector

and the dryer drain hose, the dryer drain hose may be

inserted up to 3/4 in. into the center channel of the drain

connector. See Overview of Connections, page 10.

OPTION 2: LAUNDRY TUB

Bend the end of the drain hoses to the desired shape

and support them on the edge of the laundry tub.

Use the tie strap to secure the drain hoses in place.

NOTE:

y Do not use this drain hose with a floor drain. The

end of the drain hose must be at least 29 inches

above the floor for proper draining to occur.

Drain Hose

y Inserting the dryer drain hose farther than 3/4 in.

will cause leaking and improper draining.

CAUTION

Drain Hose

Drain

hose

Band

Clamp

Drain

Y Con-

nector

MFL68267007_E.indd 12 17. 1. 19. 오후 6:52

13

ENGLISH

INSTALLATION INSTRUCTIONS

LEVELING THE WASHING MACHINE

The washer tub of your new washing machine spins

at very high speeds. To minimize vibration, noise, and

unwanted movement, the floor must be perfectly level

and solid.

• Check that the washing machine is level.

- Check for levelness by rocking the top edges of the

washing machine or placing a level on the washing

machine. The slope beneath the washing machine

must not exceed 1/2", and all four leveling feet must

rest firmly on the floor.

Level

1/2"

• Turn the lower leveling feet clockwise to level the

washing machine.

- Turning the lower leveling feet clockwise raises the

washing machine.

Raise

• Turn the locknuts counterclockwise and tighten

them when the washing machine is level.

Tighten all 4 lock

nuts securely using

the wrench.

• Check again that the washing machine is level.

- Push or rock the top edges of the washing

machine gently to make sure that the washing

machine does not rock.

- If the washing machine rocks, repeat steps 1 to

3.

y

Using the washing machine without leveling

may cause it to malfunction, producing excess

vibration and noise.

y

When stacking the full-size washing machine

on the pedestal washer, use the leveling

feet on the pedestal washer to level both.

The full-size washing machine´s leveling feet

should be minimized and the locknuts turned

counterclockwise to secure them.

y

Use the leveling feet only when you level the

washing machine.

If you raise the leveling feet

unnecessarily, it may cause abnormal vibration

of the washing machine.

WARNING

USING NON-SKID PADS (OPTIONAL)

If you install the washing machine on a slippery

surface, it may move because of excessive vibration.

Incorrect leveling may cause malfunction through

noise and vibration. If this occurs, lay the non-skid

pads under the leveling feet and adjust the level.

• Clean the floor to attach the non-skid pads.

- Use a dry rag to remove foreign objects or

moisture. If moisture remains, the non-skid pads

may slip.

• Adjust the level after placing the washing machine

in the installation area.

• Place the adhesive side of the non-skid pad on the

floor.

- It is most effective to install the non-skid pads

under the front legs. If it is hard to place the pads

under the front legs, place them under the back

legs.

Remove

backing

This side up

Adhesive

side

• Check again that the washing machine is level.

- Push or rock the top edges of the washing

machine gently to make sure that the washing

machine does not rock. If the washing machine

rocks, level the washing machine again.

MFL68267007_E.indd 13 17. 1. 19. 오후 6:52

14

INSTALLATION INSTRUCTIONS

CONNECTING TO THE POWER

SUPPLY

The washer should be plugged into a 120 VAC, 60

Hz, 3-prong (grounded) outlet. Plug in the washer.

y

The power outlet must be within 60 inches

(1.5 m) of either side of the washer.

y

The appliance and outlet must be positioned so

that the plug is easily accessible.

y

Plug the washer into an electrical outlet which

has a voltage rating that matches the rating

plate. For best performance, plug the washer

into its own individual outlet.

This helps prevent

overloading house wiring circuits which could

cause a fire hazard from overheated wires.

If necessary, use a new, UL-listed 3-prong

adapter or 3-wire extension cord with a 3-prong

(grounding) plug rated at no less than the

branch circuit. Do not use an extension cord

longer than three feet. Failure to follow these

warnings can cause serious injury, fire, electric

shock, or death.

y

The outlet must be grounded in accordance

with current wiring codes and regulations.

y

Time-delay fuse or circuit breaker is

recommended.

y

It is the personal responsibility and obligation

of the product owner to have a proper outlet

installed by a qualified electrician.

y

Do not use a worn or damaged power cord or

power plug. Replace or repair it immediately.

Failure to do so may result in death, fire, electric

shock, or malfunction.

y

Do not modify the power cord and take care

not to damage it when installing or moving the

washing machine.

Failure to do so may result in

death, fire, electric shock, or malfunction.

y

Make sure that the washing machine is

grounded.

y

Connect this washing machine to a grounded

outlet conforming to the rating prior to use.

Failure to do so may result in fire, electric

shock, or malfunction.

y

Do not damage or cut off the ground prong of

the power cord.

Doing so may cause death,

fire, electric shock, or product malfunction.

WARNING

y

Improper connection of the equipment

grounding conductor can result in risk of electric

shock. Check with a qualified electrician or

service technician if there is doubt that the

outlet is properly grounded. Do not modify the

plug provided with the appliance. Never damage

or cut off the ground prong of the power cord.

If the cord does not fit the outlet, have a proper

outlet installed by a qualified electrician. Failure

to follow these warnings can result in serious

injury, fire, electric shock, or death.

WARNING

MFL68267007_E.indd 14 17. 1. 19. 오후 6:52

15

ENGLISH

INSTALLATION INSTRUCTIONS

FABRIC CARE LABELS

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to the

manufacturer’s recommendations.

Fabric Care Labels

LOADING THE WASHER

y Check all pockets to make sure that they are empty.

Items such as clips, matches, pens, coins, and keys

can damage both the washer and the clothes.

y Close zippers, hooks, and drawstrings to prevent

these items from snagging or tangling on other

clothes.

y Pretreat heavily stained areas for best results.

y To prevent an out-of-balance load, do not wash single

items. Add one or two similar items to the load.

Large, bulky items, such as a blanket, comforter, or

bedspread, should be washed individually in the full-

size washer.

y The washer will not fill or operate with the lid open.

y Don't overload the tub. Clothes should fit loosely in

the tub under the maximum fill line. Loading clothes

over the fill line may result in damage to clothing and

the washer.

SORTING WASH LOADS

GROUPING SIMILAR ITEMS

For the best washing results, and to reduce the

possibility of damage to clothing, sort the clothing

into loads that are made up of similar items.

Mixing different fabric types and/or soil levels can

result in poor wash performance, color transfer,

discoloration, fabric damage or linting. Sort fabrics

into groups as described below.

COLORS

Sort articles by color. Wash dark clothes together in

a separate load from light colors or whites. Mixing

dark clothes with light clothes can result in dye

transfer or discoloration of the lighter clothes.

SOIL LEVEL

Wash heavily soiled clothing in the full-sized

washer. Washing lightly soiled clothing in the same

load with heavily soiled clothing could result in poor

wash performance for the lightly soiled clothing.

The pedestal washer is optimized for use with

lightly soiled and delicate items.

FABRIC TYPE

Do not mix delicate items with heavier or sturdier

fabrics. Washing heavier fabrics in a delicate load

can result in poor wash performance for the heavier

fabrics and possible damage to the delicate items.

LINT TYPE

Some fabrics attract and bind lint to them while

others give off lint in the laundry process. Avoid

mixing these lint collectors and lint producers in the

same load. Mixing these fabrics results in pilling

and linting on the lint collectors. (For example, lint

collector – knit sweater; lint producer – terry cloth

towels.)

SORT LAUNDRY…

By Colors By Soil By Fabric By Lint

White Heavy Delicates Lint Producer

Lights Normal Easy Care Line Collector

Darks Light Sturdy

y Do not load items higher than the top edge of the

tub. Failure to follow this caution can result in leak-

age or damage to fabrics.

y Use the Bedding cycle in the full-size washer for

buoyant or nonabsorbent items such as pillows or

comforters. Refer to owner's manual included with

washing machine. Failure to follow this caution can

result in leakage.

CAUTION

y Close the lid until it clicks before sliding the drawer

in to begin the cycle.

CAUTION

MFL68267007_E.indd 15 17. 1. 19. 오후 6:52

16

INSTALLATION INSTRUCTIONS

DETERGENT AND DISPENSER USE

A WORD ABOUT DETERGENTS

High-Efficiency (HE) detergents produce fewer

suds, dissolve more efficiently to improve wash-

ing and rinsing performance, and help to keep the

interior of your washer clean. Using detergent that

is not HE may cause oversudsing and unsatisfac-

tory performance which could result in error codes,

cycle failure, and machine damage.

This machine requires very little detergent. For

proper wash performance, always use the dispenser

and measuring device provided with the machine.

The dispenser holds a maximum of 2 teaspoons

(10g/10cc) of HE detergent. Most normal loads

require only 1 teaspoon (5g/5cc) of detergent, or

filling the dispenser to the halfway line.

Using too much detergent may cause oversudsing

and unsatisfactory performance. Reduce detergent

amount or add an extra rinse if detergent residue is

left on fabrics. To add an extra rinse, press the Extra

Rinse button.

DESIGNED TO USE ONLY

HIGH-EFFICIENCY (HE)

DETERGENT

IMPORTANT: Your washing machine is designed

for use with only High-Efficiency (HE) detergents.

HE detergents are formulated specifically for High-

Efficiency washers and contain suds-reducing

agents. Always look for the HE symbol when

purchasing detergent.

IMPORTANT: Not all detergents are the same. Pay

careful attention to the amount of detergent used

to avoid oversudsing, poor rinsing and detergent

buildup in clothing, and residue buildup that can

contribute to odors in the machine. The maximum

measure on the dispenser provided should only be

used for very large loads. Using too much detergent

can result in detergent buildup in the washer and in

your clothes.

Always measure the detergent amount. While HE

detergents are designed for this type of washing

machine, be careful when measuring the detergent.

For most normal loads, no more than 1 teaspoon or

half the provided dispenser/measuring device of HE

detergent should be used.

Max load

(2 tsp., 10 g)

Normal

(1 tsp., 5 g)

NOTE:

y Extra care must be exercised when using 2X and

3X concentrated detergents because even a little

bit extra can contribute to the problems mentioned

above.

y Detergents designated as HE compatible may not

provide optimal results.

USING THE DETERGENT

1. Slide the drawer open, open the lid, and add the

garments into the tub.

2. Measure the detergent with the detergent

dispenser and pour it into the tub.

3. Close the lid, slide the drawer closed, and press the

START/PAUSE button to start the cycle.

NOTE: Liquid chlorine bleach or powdered bleach

cannot be used in the pedestal washer. To use bleach,

use the full-size washer and follow instructions in the

owner's manual for that machine.

IMPORTANT: Do not place or store laundry products,

such as detergent, bleach, or liquid fabric softener,

on top of your washer or dryer. Wipe up any spills

immediately. These products can damage the finish

and controls.

USING BLEACH

Do not use liquid chlorine bleach or powdered

bleach in the pedestal washer. To bleach items, use

the full-size washer and follow the instructions in the

owner's manual included with that machine.

USING FABRIC SOFTENER

The pedestal washer chimes repeatedly before the

final rinse so liquid fabric softener can be added to

the load, if desired. Use 1/4 the amount of softener

recommended by the manufacturer for a normal load.

When the machine chimes, press Start/Pause to pause

the cycle.

1. Slide the drawer open, open the lid, and add the

liquid fabric softener to the detergent dispenser. The

softener can also be diluted with water and added

directly into the tub. Do not pour undiluted softener

directly onto clothing because it may stain fabrics.

2. Close the lid, slide the drawer closed, and press

Start/Pause to restart the cycle.

3. To disable or enable the fabric softener alert, press

and hold the Warm Water and Extra Rinse buttons at

the same time for three seconds.

If you miss the softener add point:

1. Press the Power button to interrupt the cycle.

2. Select the Rinse+Spin cycle and press the Start

button to start the cycle.

3. Add the fabric softener at the chimes following

instructions above.

MFL68267007_E.indd 16 17. 1. 19. 오후 6:52

17

ENGLISH

HOW TO USE

CONTROL PANEL FEATURES

A

POWER (ON/OFF) BUTTON

Press to turn the washer ON. Press again to

turn the washer OFF. Pressing the POWER

button during a cycle will cancel that cycle

and any load settings will be lost. The drawer

will unlock after a brief pause.

NOTE:

• When the Power button is pressed, the

Normal cycle is selected by default. To

modify the default options or choose

another cycle, press the cycle selector (v)

button to illuminate the display.

B

CYCLE SELECTOR BUTTON

Press this button to select the desired cycle.

Once the desired cycle has been selected,

the standard presets will appear in the

display. These settings can be adjusted

using the cycle setting buttons any time

before starting the cycle.

NOTE: To protect your clothing, not all

settings are available on all cycle selections.

C

START/PAUSE BUTTON

Press this button to start the selected cycle.

If the washer is running, use this button to

pause the cycle without losing the current

settings.

NOTE: If you do not press the START/

PAUSE button within 4 minutes of selecting

a cycle, the washer automatically turns OFF

and all cycle settings are lost.

D

OPTION BUTTONS

Use these buttons to adjust the settings for

the selected cycle. The setting lights above

the buttons illuminate to show the current

selection.

E

TIME AND STATUS DISPLAY

The display shows the cycle status and

estimated time remaining.

F

REMOTE CONTROL SENSOR

Use the remote to set the controls without

bending down to reach the control panel.

HOW TO USE

A B C

DE F

MFL68267007_E.indd 17 17. 1. 19. 오후 6:52

18

HOW TO USE

TIME AND STATUS DISPLAY

The time and status display shows the estimated time remaining and cycle progress.

A

DRAWER LOCK INDICATOR

The DRAWER LOCK indicator will illumi-

nate once a cycle has started. The indi-

cator light will stay on until the cycle is

paused, stopped or has finished.

B

CHILD LOCK

When the Child Lock function is ac-

tivated, the LED lights up. When the

Child Lock function is set, except for the

POWER button, the other functions are

disabled. Once the Child Lock function is

disabled, the LED will turn off.

C

CYCLE STATUS INDICATOR

These LEDs will illuminate when a cycle

is selected to indicate which stages will

run. When a cycle is running, the LED for

the active stage will blink, and the LEDs

for the remaining stages will remain

steady. Once a stage is complete, the

LED will turn off. If a cycle is paused, the

active stage LED will stop blinking.

D

ESTIMATED TIME REMAINING

When a cycle is selected, the default

time for that cycle is displayed. This time

will change as modifiers or options are

selected.

NOTE: The time shown is only an esti-

mate. This time is based on normal oper-

ating conditions. Several external factors

(load size, room temperature, incoming

water temperature, water pressure, etc.)

can affect the actual time.

CD

A B

MFL68267007_E.indd 18 17. 1. 19. 오후 6:52

19

ENGLISH

HOW TO USE

OPERATING THE WASHER

y

To reduce the risk of fire, electric shock, or injury to persons,

read the IMPORTANT SAFETY

INSTRUCTIONS before operating this appliance.

WARNING

Softener

Bleach

Detergent

Softener

Bleach

Detergent

1

SORT LAUNDRY AND LOAD THE WASHER

Sort laundry by fabric type, soil level, color

and load size, as needed. Open the lid and

load items into the washer.

2

CLEANING PRODUCTS

Measure High-Efficiency (HE) detergent with

the dispenser and pour it into the washer.

3

TURN ON THE WASHER

Press the POWER button to turn ON the

washer. The cycle lights illuminate and a

chime sounds.

4

SELECT A CYCLE

Press the cycle selector button to select the

desired cycle. When you press Power the

Normal cycle is selected by default. To modify

the options, press the cycle selector button

to activate the display. The optional remote

control can also be used to select the desired

cycle.

5

ADJUST SETTINGS

Default settings for the selected cycle can

now be changed, if desired, using the option

buttons.

NOTE: Not all options are available on all cycles.

A different chime will sound and the light will

not turn on if the selection is not allowed.

6

BEGIN CYCLE

Press down gently on the lid handle until

it clicks and slide the drawer closed. Press

START/PAUSE to begin the cycle. The

drawer locks, and the washer starts the

cycle. If the START/PAUSE button is not

pressed within 4 minutes, the washer shuts

off and all settings are lost.

7

ADD FABRIC SOFTENER

A repeated chime sounds before the final

rinse. When the chime sounds, pause the

machine and add liquid fabric softener within

three minutes, if desired.

8

END OF CYCLE

When the cycle is finished, a melody will

sound. Immediately remove the clothing

from the washer to reduce wrinkling.

MFL68267007_E.indd 19 17. 1. 19. 오후 6:52

20

HOW TO USE

CYCLE GUIDE

The cycle guide below shows the default settings, available options

and recommended fabric types for each cycle. Allowable modifier

adjustments are shown below the default setting for each cycle.

Cycle Cycle Use

Est. Time

Wash Temp. Extra Rinse Child Lock

Normal

Lightly soiled cotton, t-shirts, towels, jeans,

mixed loads.

39 ~ 116

Warm

 

Cold

Intimates

Lingerie, underwear, pajamas, delicates,

etc.

47 ~ 103

Warm

 

Cold

Hand Wash

Sweaters, knits, items labeled

hand-washable, etc.

47 ~ 103

Warm

 

Cold

Active Wear

Specially designed/treated performance

clothing.

43 ~ 103

Warm

 

Cold

Rinse + Spin

Pre-treats stains, or rinses off soap and

drains tub

8 ~ 90

 

Tub Clean Cleans tub and removes mildewy odor. 58

Warm



Cold

Active Wear

Use this cycle to wash performance garments that

are specially designed and treated for sports.

Rinse + Spin

Select this option to rinse and spin a load separately

from a regular cycle. This can be helpful in preventing

fresh stains from setting in fabrics.

Spin Only Cycle

To activate a spin only cycle, select the Rinse+Spin

cycle. Then press the Extra Rinse button six times

or until the display shows 8 and the Rinse icon is no

longer illuminated on the panel.

Tub Clean

Use this cycle to clean the tub of the washing

machine.

WASH CYCLES

Wash cycles are designed for the best wash

performance for each type of load. Select the cycle

that best matches the load contents for maximum

wash performance and fabric care. Press the

cycle selector button to select the desired cycle.

When you select a wash cycle, the light for the

corresponding wash cycle will turn on. See page

19,

OPERATING THE WASHER

, for more details on

operating methods.

Normal

Use this cycle to wash lightly soiled normal items,

except delicate fabrics such as wool or silk.

NOTE:

Pressing the START/PAUSE button without

selecting a cycle will cause the NORMAL cycle to

begin immediately using the default settings.

Intimates

Use this cycle to wash delicate items such as

lingerie or sheer and lacy clothes which could easily

be damaged in a normal cycle. This cycle is not for

silk items.

Hand Wash

Use this cycle to wash shrinkable woolen or hand-

washable items requiring delicate care. Only wash

woolen items that are labeled machine wash or hand

wash.

Key

Default



Available option

MFL68267007_E.indd 20 17. 1. 19. 오후 6:52

La page charge ...

LG WD100CV Le manuel du propriétaire

Ce manuel convient également à

LG WD100CV Le manuel du propriétaire

dans d''autres langues

Documents connexes