Modern Forms WS-W20118 Reflect Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
201-Outdoor Sconce
WS-W20118
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Aug. 2020
CAUTION: To prevent electrical shock, ensure electricity has been turned off at the circuit breaker before beginning.
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
• Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern
Forms could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any
parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that customers in coastal
areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de commencer.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus
pour ce produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la
garantie. Veuillez contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chiffon humide.
Wire Connector
Qty:3+1Extra
A
B
Mounting Screw
Qty:1Extra
E
Allen Wrench
Qty:1pc
C
Silicone Gasket
Qty:1Extra
D
Hexagon Socket Screw
Qty:4+1Extra
2
INSTALLATION INSTRUCTIONS
201-Outdoor Sconce
WS-W20118
FIG. 1
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Aug. 2020
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
PREPARATION
1. Shut off the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area.
Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) and
Silicone Gasket (C)
from the xture.
4. Secure the mounting back plate to the junction box using standard junction box
screws that comes with the junction box.
Note: (i) Using any other non-original-manufacturer provided junction box screw
may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
5. Lay the front side of the xture on a clear area, insert the top and bottom
glass into the xture, the screw hole face up. Secure the glass to the xture
with hexagon socket screws (D) using the allen wrench (E) provided.
CONNECTING THE WIRES (Fig. 2)
6. Connect the xture’s input wires to junction box wires as shown in Fig. 2, make
sure that all wire connectors (A) are secured. If your outlet box has a green or
bare copper ground wire, connect the xture’s ground wire to it. Otherwise,
connect the xture’s ground wire directly to the back plate using the screw
provided. After wires are connected, tuck them carefully inside the junction box.
7. Secure the xture to the mounting back plate using the mounting screw (B) and silicone gesket (C) .
8. To prevent moisture from entering the outlet box and causing a short, use clear caulking(i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets the wall. Leave a space at the bottom to allow the moisture to escape (Fig. 3).
B
A
Mounting Screw
Mounting BackPlate
Wire Connector
Junction Box
Ground Wire
Junction Box Screw
Allen Wrench
Silicone Gasket
Hexagon Socket Screw
Bottom Glass
Top Glass
(RPL-GLA-20118-02)
(RPL-GLA-20118-01)
E
C
D
Mounting Backplate Dimension
41
2"
41
8"
Ø23
4"
Ø31
2"
Caulking
Junction Box
Fig.3 Sealing
-
1
-
2
Modern Forms WS-W20118 Reflect Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms WS-W54016 Mist Mode d'emploi
-
-
-
-
-
-
-
-
-