Modern Forms PD-52708 Marimba Mode d'emploi
- Taper
- Mode d'emploi
1
INSTALLATION INSTRUCTIONS
527 –LED Pendant
PD-52708
-Read all instructions before installing.
-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC)
and local regulations.
-When handling the fixture, do not apply pressure to the LEDs. Hold the fixture by the base only.
-Retain installation instructions for future maintenance reference.
-Lisez toutes les instructions avant l’installation.
-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et
également aux règlements locaux.
-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
HARDWARE
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Wire Connector
Qty: 3pcs+1Extra
Mounting Screw
Qty: 1Extra
AB
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE
CIRCUIT BREAKER BEFORE BEGINNING.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour
être utilisé seulement avec les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms.
Remplacer des pièces ou accessoires non conçus pour ce produit Modern Forms pourrait causer des dommages
corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez contacter un revendeur autorisé
ou le fabricant si des pièces manquent ou sont endommagées.
NOTE D’ENTRETIEN: Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire.
Nous recommendons aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du
luminaire une fois toutes les deux semaines avec un chiffon humide.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the
supplied parts and/or accessories designated for use by Modern Forms. Substitution of parts or accessories not
designated for use with this product by Modern Forms could result in personal injury or property damage, and will void
the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.
MAINTENANCE NOTE: Coastal conditions may cause mineral and residue build-up on the fixture. We recommend that
customers in coastal areas clean all external surfaces of the fixture once every two weeks with a wet cloth.
MISE EN GARDE: Pour éviter tout choc électrique, assurez-vous que le disjoncteur soit mis hors tension avant de
commencer.
2
INSTALLATION INSTRUCTIONS
527 –LED Pendant
PD-52708
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 2 Wiring
FIG. 1
1. Shut off the power at the circuit breaker and
remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all
the parts on a clear area. Be careful not to lose
any small parts necessary for installation.
8. Secure the canopy over the mounting plate using the mounting screw (B).
9. Twist lock the glass diffuser into the shade.
PREPARATION
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Secure the mounting plate to the junction box using
the screws provided with the junction box.
NOTE: The side of the mounting plate marked “GND” must face out.
5. Adjust the fixture wire length by pushing the cable-gripper on the canopy
and pulling the wire as desired. Make sure the wires are the same length.
a. Retract the wires to a desirable length within the canopy before
securing the fixture into place.
NOTE: Using the cable-gripper to adjust more than 18" of wire is
not recommended.
WARNING: Shortening cables without professional help or electronic
background is not advisable. Any modifications to the fixture will
result in voiding the warranty of the product.
6. Re-set the strain relief nearing the wiring holes.
CONNECTING THE WIRES (Fig. 2)
7. Connect the transformer’s input wires to junction box wires as shown
(Fig. 2). Make sure that all wire connectors (A) are secure. If your outlet box
has a green or bare copper ground wire, connect the fixture’s ground wire to
it. Otherwise, connect the fixture’s ground wire directly to the back plate
using the green screw provided. After wires are connected, tuck them
carefully inside the junction box.
COMPLETING THE INSTALLATION
Mounting Plate Dimensions
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Jan 2019
ANUARY, 2017
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Cable-gripper
Junction Box
Supply wire
Wire Connector
Junction Box Screw
Transformer
(Output)
Ground Wire
Ground Wire Screw
Mounting Screw
Input
Mounting Plate
Strain Relief
Canopy
A
B
∅4-3/4"
1 3/8"
1 3/4"
-
1
-
2
Modern Forms PD-52708 Marimba Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
Modern Forms BL-54307 Nexus Mode d'emploi
-
-
-
-
-
-
-
WAC Lighting FM-W47205-40-BK Mode d'emploi
-
-