Fisher & Paykel HP36ILTX2 Mode d'emploi

INTEGRATED INSERT

VENTILATION HOOD

HP24ILTX2 and HP36ILTX2 models

HOTTE DE VENTILATION

ENCASTRABLE

Modéls HP24ILTX2 et HP36ILTX2

INSTALLATION GUIDE / USER GUIDE

GUIDE D’INSTALLATION / GUIDE D’UTILISATION

US CA

English Page 1 – 21

Français

Page 23 – 43

1

CONTENTS

Introduction 3

Safety and warnings 4

Installation instructions 7

Operating instructions 15

Cleaning and maintenance 16

Parts and accessories 18

Limited Warranty 19

Registration

To register your product visit our website: fisherpaykel.com/register

EN

3

INTRODUCTION

Thank you for purchasing a Fisher & Paykel product.

Thousands of hours go into the design, engineering, testing and perfecting of each

Fisher & Paykel appliance. The care and attention given to creating these beautiful

products doesn’t stop once it has found its home with you.

This use and care manual will answer most of your questions about the set-up, use

and on-going maintenance of your Fisher & Paykel product; however if you require

further information about your product and its use please consult our website for

solutions and further contact information to discuss with a service representative.

To ensure you receive all relevant product updates and the best service possible,

please register your Fisher & Paykel products through our website.

EN

4

SAFETY AND WARNINGS

!WARNING!

Weight Hazard

The ventilation hood is heavy. Please ensure adequate care is taken

wheninstalling the ventilation hood to prevent personal injury.

The ventilation hood must be installed onto a solid wall, stud, beam

ortruss.

Product weight: 16lbs (7.1kg) HP24 / 20lbs (9.1kg) HP36.

!WARNING!

Electric Shock Hazard

Always disconnect the appliance from the mains power supply before

carrying out any maintenance or repairs.

Installation work and electrical wiring must be done by qualified

person(s) in accordance with all applicable codes and standards,

including fire-rated construction.

Failure to do so can result in death, electric shock, fire or injury to

persons.

5

SAFETY AND WARNINGS

IMPORTANT SAFETY INSTRUCTIONS

READ THE ENTIRE SET OF INSTRUCTIONS BEFORE INSTALLING OR USING

THIS APPLIANCE. Manuals can also be found on our website www.fisherpaykel.com.

 CAUTION: For general ventilating use only. Do not use to exhaust hazardous

or explosive materials and vapors.

 WARNING! To reduce the risk of fire, electric shock, or injury to persons, observe

thefollowing:

– Use this unit only in the manner intended by the manufacturer. If you have

questions, contact the manufacturer. For residential use only.

– Before servicing or cleaning unit, switch power off at service panel and lock

the service disconnecting means to prevent power from being switched on

accidentally. When the service disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to the service panel.

– Installation work and electrical wiring must be done by qualified person(s)

in accordance with all applicable codes and standards, including fire-rated

construction.

– Sufficient air is needed for proper combustion and exhausting of gases through

the flue (chimney) of fuel burning equipment to prevent back drafting. Follow

the heating equipment manufacturer’s guideline and safety standards such as

those published by the National Fire Protection Association (NFPA), and the

American Society for Heating, Refrigeration and Air Conditioning Engineers

(ASHRAE), and the local code authorities.

– When cutting or drilling into wall or ceiling, do not damage electrical wiring

and other hidden utilities.

– Ducted fans must always be vented to the outdoors.

– This unit must be grounded.

 CAUTION: To reduce risk of fire and to properly exhaust air, be sure to duct air

outside – Do not vent exhaust air into spaces within walls or ceilings or into attics,

crawl spaces, or garages.

 WARNING: To reduce the risk of fire, use only metal ductwork.

 WARNING: To reduce the risk of fire or electric shock, do not use this fan with

any solid-state speed control device.

 WARNING: To reduce the risk of a range top grease fire:

– Never leave surface units unattended at high settings. Boilovers cause smoking

and greasy spillovers that may ignite. Heat oils slowly on low or medium

settings.

– Always turn hood ON when cooking at high heat or when flambéing food (ie

Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé)

– Clean ventilating fans frequently. Grease should not be allowed to accumulate

on fan or filter.

– Use proper pan size. Always use cookware appropriate for the size of the

surface element.

EN

6

SAFETY AND WARNINGS

 WARNING: To reduce the risk of injury to persons in the event of a range top

grease fire, observe the following*:

– SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then

turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go

out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

– NEVER PICK UP A FLAMING PAN – You may be burned.

– DO NOT USE WATER, including wet dishcloths or towels – a violent steam

explosion will result.

– Use an extinguisher ONLY if:

– You know you have a Class ABC extinguisher, and you already know

how to operate it.

– The fire is small and contained in the area where it started.

– The fire department is being called.

– You can fight the fire with your back to an exit.

 WARNING: Unplug or disconnect the appliance from the power supply before

servicing or cleaning.

READ AND SAVE THESE INSTRUCTIONS

*Based on “Kitchen Firesafety Tips” published by NFPA.

7

IINSTRUCTIONS D’INSTALLATION

Contents of packaging

Installation instructions

User guide manual

(1)

Ventilation hood

(1)

3/8” (10mm)

Self tapping screw

(4)

Power connection box

(1)

6” (152mm) diameter

Ducting adapter with

back draft damper

(1)

US CA

INSTALLATION INSTRUCTIONS

USER GUIDE

INSTRUCTIONS D’INSTALLATION

GUIDE D’UTILISATION

HP24ILTX1 and HP36ILTX1 models

Modèles HP24ILTX1 et HP36ILTX1

Integrated Perimeter Insert Ventilation Hood

Hotte de Ventilation Périmétrique Encastrable

EN

8

INSTALLATION INSTRUCTIONS

Product and cabinetry cutout dimensions

K

L

ØM

A

E

B

G

D

P

F

C

I

J

H

O

N

UL power

connection box

Ducting adapter

9

INSTALLATION INSTRUCTIONS

EN

HP24 HP36

PRODUCT DIMENSIONS inches (mm) inches (mm)

AOverall height of product 133/4” (350) 13 3/4” (350)

BOverall height of product (with

power connection box)

181/4” (463) 181/4” (463)

COverall width of product 207/8” (530) 3211/16” (830)

DOverall depth of product 11” (280) 11” (280)

EThickness of flange 1/16” (2) 1/16” (2)

FWidth of chassis 193/8” (492) 313/16” (792)

GDepth of chassis 101/16” (255) 101/16” (255)

HHeight of side of chassis 711/16” (195) 711/16” (195)

IWidth of top surface of chassis 113/4” (298) 113/4” (298)

JLength of angled surface of chassis 67/8” (175) 11” (280)

KDistance from center of ducting

outlet to back of chassis

31/8“ (80) 31/8” (80)

LDistance from center of ducting

outlet to side of chassis

95/8” (245) 159/16” (395)

MDiameter of ducting outlet 6” (152) 6” (152)

NDistance between center of lights 143/4” (375) 269/16” (675)

ODistance from center of light to

front of product

19/16” (40) 1 9/16” (40)

CABINETRY CUTOUT DIMENSIONS

Overall width of cutout 1911/16” (500) 311/2” (800)

Overall depth of cutout 101/4” (260) 101/4” (260)

PBase of brackets/clips to bottom of

chassis

min. 9/16” – max. 19/16”

(min. 15 – max. 40)

min. 9/16” – max. 19/16”

(min. 15 – max. 40)

IMPORTANT!

Actual product dimensions may vary by ± 1/16”(2mm).

Please read the entire instructions before installing the ventilation hood.

10

INSTALLATION INSTRUCTIONS

Height of ventilation hood

MINIMUM CLEARANCES inches (mm)

QHeight top of cooktop to base

of product

min. 26” – max. 30” (min 660 – max. 762)

This ventilation hood must be installed no lower than the minimum height indicated

in the table above. Minimum installation height may be greater if required by the

cooktop manufacturer or safety and warning section of this user guide. Installation

at the minimum height will improve the efficiency of capturing cooking odors, grease

and smoke. Installation at the maximum height improves user ergonomics by offering

increased head room.

Q

11

INSTALLATION INSTRUCTIONS

WARNING!

To reduce the risk of fire, use only metal ductwork. Do not use flexible plastic ducting

CAUTION!

To reduce risk of fire and to properly exhaust air, be sure to duct air outside – do not

vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or

garages.

Venting options

Attention should be given to ensure that any applicable regulations concerning the

discharge of exhaust air are fulfilled.

The ventilation hood can be installed to operate with the exhaust air ducted

externally from the kitchen.

Ducted

For ducted installation it is recommended that 6” (152mm) diameter, rigid or semi-rigid

ducting is used. This will require a 65/16” (160mm) (min) round hole in the ceiling or

wall. Care should be taken to position the hole correctly.

For optimal efficiency use the shortest and straightest duct route possible and use rigid

or semi-rigid ducting for reduced noise and increased airflow. Flexible metal ducting

should only be used as a last resort (ie in difficult installations) and if used ensure that it

is straight and smooth and extended as much as possible.

EN

12

INSTALLATION INSTRUCTIONS

WARNING!

 This appliance is heavy and requires two persons for unpacking and installation

 Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards.

 Failure to install the screws or fixing device in accordance with these instructions

mayresult in electrical hazards

IMPORTANT!

Wear gloves to protect against sharp edges.

The manufacturer is not liable for any damage caused by not following these instructions.

Installation

1 Prepare for installation.

Before installing your ventilation hood:

 Please read the instructions carefully.

 Unpack the ventilation hood and check that all

functions are working.

 Ensure that the voltage (V) and the frequency (Hz)

indicated on the serial plate match the voltage and

frequency at the installation site.

 The stainless steel surfaces of the ventilation

hood are very easily damaged during installation

if grazed or knocked by tools. Please take care to

protect the surfaces during installation.

 Protect the cooktop surface below with cardboard,

or the like, to prevent damage occurring whilst the

ventilation hood is being installed above.

2 Attach ducting adapter and power connection box to

the ventilation hood

 Place the ducting adapter onto the ventilation

hood and screw it in place using 3/8” (10mm)

screws.

 Place the power connection box onto the

ventilation hood and screw it in place using 3/8”

(10mm) screws.

 Follow wiring instructions described in the

‘Electrical connection’ section page14.

3 Provide an opening on the underside of the cupboard

(see product and cabinetry cutout dimensions).

It is also recommended that the cupboard has a door

or service panel that can be easily opened to access

the power connection box

width

depth

13

INSTALLATION INSTRUCTIONS

EN

1

2

4 Remove the filters and face plate of the ventilation hood.

5 Lift the ventilation hood and fit through the opening of the cupboard till the spring

loaded brackets / clips hold the product in place.

x4

6 Secure ventilation hood while tightening the 4 brackets / clips.

Images are for representation only, models may vary.

14

INSTALLATION INSTRUCTIONS

WARNING!

Electrical wiring must be done by qualified person(s) in accordance with all applicable

codes and standards and the unit must be grounded.

7 Electrical connection

 Run three wires, two for the power supply and one for the ground wire, from the

power connection box on the ventilation hood to a power connection point near

the installation.

 Open the power connection box on the ventilation hood and secure the power

conductor with a cULus listed strain relief (not included).

 Connect the power conductors to the conductors for the ventilation hood, black to

black and white to white.

 Connect the grounding wire (green or bare) to the ground conductor (green) of the

ventilation hood power connection box.

 Secure all the connections with cULus listed wire nuts.

 Replace the power connection box cover.

EN

Gray 4 speed

Black 3 speed

Red 2 speed

Blue 1 speed

Brown (neutral)

15

OPERATING INSTRUCTIONS

Touch control panel

CONTROL PANEL FEATURES

Light Turn the lights on or off.

Power ON/OFF Turn the ventilation hood on or off. The fan

automatically turns on to operate at level 1.

Reduce fan speed Adjust the fan speed levels from 1 – 3 with 1 being

the lowest.

Fan speed indicator The fan speed level icon illuminates red with the

current fan speed.

Increase fan speed Adjust the fan speed levels from 1 – 3 with 3 being

the highest.

Max Turn the fan on directly onto maximum fan speed.

Timer Turn the timer on. The fan speed light blinks and the

fan will operate for 5 minutes at the current speed

and each decreasing speed before turning off (the

fan will stop and the light will go out).

To cancel the timer press the timer button once.

Note: for optimal performance it is recommended that the ventilation hood is

turned on before cooking is started.

IMPORTANT!

The ventilation hood may stop working during an electrostatic discharge

(eg lightning). Switch off the electricity supply to the ventilation hood and

reconnect after one minute.

16

CLEANING AND MAINTENANCE EN

WARNING!

 Unplug or disconnect the appliance from the power supply before servicing

orcleaning.

 When replacing the bulb, let the bulb cool, and assure that power to the ventilation

hood has been turned off. Use new bulbs according to that indicated on the

ventilation hood nameplate.

IMPORTANT!

 Never use abrasive or oil based cleaners

 Wear gloves to protect against sharp edges

Maintenance

The ventilation hood should be cleaned regularly

using a mild, liquid detergent and a clean soft cloth

to avoid a build-up of grease occurring. Avoid

the use of corrosive chemicals, abrasive cleaning

products, hard brushes and steel wool pads. Grease

deposits are corrosive which can cause damage to

your ventilation hood.

Note: in areas of high humidity or coastal

environments, cleaning should be carried out more

frequently.

Aluminium filters

 Depending on use, and at least once a month, the aluminium grease filters should be

removed and cleaned with hot soapy water or in a dishwasher.

 If washed in a dishwasher, the filters should be placed in an upright position to prevent

food from falling on them.

 After rinsing and drying, replace the filters.

Note: some discoloration of the frames may occur.

Removing the aluminium filters:

1 Open the stainless steel panel.

2 Pull the relative filter catch, tilting it downwards until it disengages from the supports.

3 Reverse these instructions when refitting the filters.

17

WARNING!

When replacing the bulb, let the bulb cool, and assure that power to the ventilation

hood has been turned off. Use new bulbs according to that indicated on the

ventilation hood nameplate.

Light bulb replacement

Note: replacement bulbs are not covered by warranty.

1 Open the stainless steel panel.

2 Remove the aluminum filters.

3 Unscrew the light bulb.

4 Insert the replacement bulb into the lamp socket.

5 Replace the aluminium filters.

6 Close the stainless steel panel.

CLEANING AND MAINTENANCE

Bulb replacement

18

PARTS AND ACCESSORIES

ITEM REFERENCE NUMBER

LED bulb 792966

Aluminum filter 792429

EN

La page charge ...

Fisher & Paykel HP36ILTX2 Mode d'emploi

Ce manuel convient également à

Fisher & Paykel HP36ILTX2 Mode d'emploi

dans d''autres langues

Documents connexes