VTech RM9751 Mode d'emploi

Catégorie
Moniteurs vidéo bébé
Taper
Mode d'emploi
Privacy Mode
Cable management
What’s in the box
Connect and Power On the Camera
x 2 x 2
Quick start guide
Your baby monitor package contains the following items. Save your sales receipt and original
packaging in the event warranty service is necessary.
Designed for extra peace of mind, turn on Privacy Mode for a moment of peace and quiet.
When the Privacy Mode is turned on, audio transmission and video monitoring will be disabled
so motion recording, motion detection, and sound detection will be temporarily unavailable.
Connect the power adapter to the camera and a power supply, then the camera powers on
automatically.
Overview
Camera
1Bee cover
2Light sensor
3Camera lens
4Microphone
5Night Light
6Speaker
7Status LED
8PAIR
Press and hold for three seconds to enter
pairing mode.
Reset the baby unit to factory default.
1. Press and hold PAIR key until you hear a
beep sound.
2. Release the PAIR key, and then press the
PAIR key again five times until you hear
another beep sound.
3. The baby unit will sound another beep
when the reset completes. Then, the
baby unit will reboot.
9Temperature sensor
10 Power jack
11 Wall mount slots
4
5
6
7
8
9
10
11
3
2
1
4
5
6
7
8
9
10
11
3
2
1
4
5
6
7
8
9
10
11
3
2
1
Use only the power adapter supplied with this product.
If the camera is connected to a switch controlled electric outlet, make sure the switch is on.
Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of the camera, so do not connect them to any ceiling, under-the-table, or
cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
To maintain compliance with the FCC’s RF exposure guidelines, place the camera at least 20cm from
nearby persons.
1 set for RM9751
Important safety instructions
After installing the MyVTech Baby Pro App...
Sign up for an account
Pair the camera with your mobile device
Monitor your baby using a wide range of features
Start monitoring from anywhere.
Download the free MyVTech Baby Pro mobile app and install it to a mobile device, then
use your mobile device and the mobile app to monitor your areas remotely.
Download app for mobile access
Pair the Camera with your Mobile Device
App Compatibility
AndroidTM 6.0 or later
iOS 12 or later.
On Baby Care App
Before you start...
Connect your mobile device to a 2.4GHz Wi-Fi network for a better connection and smoother video
streaming.
Enable the Location Service of your mobile device for the purpose of camera setup.
With a 2.4GHz Wi-Fi network and enabled Location Service...
You can start to pair the camera with your own mobile device following the instructions in the app.
Upon the successful pairing, you can hear and watch your baby via your mobile device.
Tips:
Move the camera and the Wi-Fi router closer to each other in order to strengthen the network signal.
It takes up around 1 minute to search the camera.
The applied nameplate is located at the bottom of the camera’s
base. When using your equipment, basic safety precautions
should always be followed to reduce the risk of fire, electric shock
and injury, including the following:
1. Follow all warnings and instructions marked on the product.
2. Adult setup is required.
3. CAUTION: Do not install the camera at a height above 2
meters.
4. This product is not a substitute for adult supervision of the
infant. Supervising the infant is the parent’s or caregiver’s
responsibility. This product could cease operating, and
therefore you should not assume it will continue working
properly for any given period of time. Further, this is not a
medical device and should not be used as such. This product
is intended to assist you in supervising your baby.
5. Do not use this product near water. For example, do not use
it next to a bath tub, wash bowl, kitchen sink, laundry tub or
swimming pool, or in a wet basement or shower.
6. Use only the adapters included with this product. Incorrect
adapter polarity or voltage can seriously damage the product.
Power adapters information:
Camera Output: 5V 1A;
VTech Telecommunications Ltd.;
Model: VT05EUS05100
7. The power adapters are intended to be correctly oriented in a
vertical or floor mount position. The prongs are not designed
to hold the plug in place if it is plugged into a ceiling, under-
the-table or cabinet outlet.
8. For pluggable equipment, the socket-outlet shall be installed
near the equipment and shall be easily accessible.
9. Unplug this product from the wall outlet before cleaning.
10. Do not use liquid or aerosol cleaners. Use a damp cloth for
cleaning. Do not cut off the power adapters to replace them
with other plugs, as this causes a hazardous situation.
11. Do not allow anything to rest on the power cords. Do not
install this product where the cords may be walked on or
crimped.
12. This product should be operated only from the type of power
source indicated on the marking label. If you are not sure of
the type of power supply in your home, consult your dealer or
local power company.
13. Do not overload wall outlets or use an extension cord.
14. Do not place this product on an unstable table, shelf, stand or
other unstable surfaces.
15. This product should not be placed in any area where proper
ventilation is not provided. Slots and openings in the back or
bottom of this product are provided for ventilation. To protect
them from overheating, these openings must not be blocked
by placing the product on a soft surface such as a bed, sofa
or rug. This product should never be placed near or over a
radiator or heat register.
16. Never push objects of any kind into this product through
the slots because they may touch dangerous voltage points
or create a short circuit. Never spill liquid of any kind on the
product.
17. To reduce the risk of electric shock, do not disassemble this
product, but take it to an authorized service facility. Opening
or removing parts of the product other than specified access
doors may expose you to dangerous voltages or other risks.
Incorrect reassembling can cause electric shock when the
product is subsequently used.
18. You should test the sound reception every time you turn on
the units or move one of the components.
19. Periodically examine all components for damage.
20. There is a very low risk of privacy loss when using certain
electronic devices, such as cameras, cordless telephones,
etc. To protect your privacy, make sure the product has never
been used before purchase, reset the camera periodically by
powering off and then powering on the units, and power off
the camera if you will not use it for some time.
21. Children should be supervised to ensure that they do not play
with the product.
22. The product is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
SAVE THESE INSTRUCTIONS
Cautions
1. Use and store the product at a temperature between 32oF
(0oC) and 104oF (40oC).
2. Do not expose the product to extreme cold, heat or direct
sunlight. Do not put the product close to a heating source.
3. Warning—Strangulation Hazard—Children
have STRANGLED in cords. Keep this cord out of
the reach of children (more than 3 ft (0.9m) away).
Do not remove this tag.
4. Never place the camera(s) inside the baby’s crib or playpen.
Never cover the camera(s) with anything such as a towel or a
blanket.
5. Other electronic products may cause interference with your
camera. Try installing your camera as far away from these
electronic devices as possible: wireless routers, radios, cellular
telephones, intercoms, room monitors, televisions, personal
computers, kitchen appliances and cordless telephones.
Precautions for users of implanted cardiac pacemakers
Cardiac pacemakers (applies only to digital cordless devices):
Wireless Technology Research, LLC (WTR), an independent
research entity, led a multidisciplinary evaluation of the
interference between portable wireless devices and implanted
cardiac pacemakers. Supported by the U.S. Food and Drug
Administration, WTR recommends to physicians that:
Pacemaker patients
Should keep wireless devices at least six inches from the
pacemaker.
Should NOT place wireless devices directly over the
pacemaker, such as in a breast pocket, when it is turned ON.
WTR’s evaluation did not identify any risk to bystanders with
pacemakers from other persons using wireless devices.
Electromagnetic fields (EMF)
This VTech product complies with all standards regarding
electromagnetic fields (EMF). If handled properly and according
to the instructions in this user’s manual, the product is safe to be
used based on scientific evidence available today.
Position the Camera
> 3ft (1m)
Tips:
You can find the wall mounting tutorial video and step-
by-step guide by visiting our Online Manual.It takes up
around 1 minute to search the camera.
Pan and Tilt your camera
RM9751
What does HD Video Monitor do?
Quick start guide
Wi-Fi 1080p Yellow Daisy Baby Camera allows you to stay close to your baby when you are
on the move or away. This monitor is Wi-Fi enabled, using your home wireless network to
stream live video and audio through the 1080p baby camera and mobile devices. It allows
you to maintain a constant connection to your baby. Wi-Fi 1080p Yellow Daisy Baby Camera
uses MyVTech Baby Pro app to let you instantly see and hear what’s happening with your
baby from anywhere in the world. The app can be downloaded from the App Store or the
Google PlayTM Store.
You can also monitor from your smartphone and mobile tablet. VTech 5” Smart Wi-Fi
1080p Video Monitor uses MyVTech Baby Pro app to let you instantly see and hear what’s
happening with your baby from anywhere in the world. The app can be downloaded from
the App Store or the Google PlayTM Store.
1 2 3
Wi-Fi 1080p
Yellow Daisy Baby Camera
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
latest VTech product news.
RM9751
For more support information:
S
m
Congratulations
on purchasing your new VTech product. Before using this HD video monitor, please read
Important safety instructions.
For support, shopping, and everything new at VTech, visit our website at
www.vtechphones.com. In Canada, visit www.vtechcanada.com.
VTech cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-
recommended best practices to help keep your wireless connection private and your devices protected
when online.
Ensure your wireless connection is secure
Before installing a device, ensure your router’s wireless signal is encrypted by selecting the “WPA2-PSK
with AES” setting in your router’s wireless security menu.
Change default settings
Change your wireless router’s default wireless network name (SSID) to something unique.
Change default passwords to unique, strong passwords. A strong password:
- Is at least 10 characters long.
- Does not contain dictionary words or personal information.
- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.
Keep your devices up to date
Download security patches from manufacturers as soon as they become available. This will ensure
you always have the latest security updates.
If the feature is available, enable automatic updates for future releases.
Disable Universal Plug and Play (UPnP) on your router
UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network
devices to open inbound ports without any intervention or approval from you. A virus or other
malware program could use this function to compromise security for the entire network.
For more information on wireless connections and protecting your data, please review the following
resources from industry experts:
1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips – www.fcc.
gov/consumers/guides/how-protect-yourself-online.
2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet – www.
us-cert.gov/ncas/tips/ST15-003.3.
3. Federal Trade Commission: Using IP Cameras Safely –
https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.
4. Wi-Fi Alliance: Discover Wi-Fi Security
http://www.wi-fi.org/discover-wi-fi/security.
Mount the Camera (Optional)
How the system works ?
Protect Your Privacy and Online Security Test the Location for the Camera
Your home Wi-Fi network provides Internet connection to your camera so that you can
monitor and control your camera whenever you are through the MyVTech Baby Pro App.
Your Wi-Fi router (not included) provides the Internet connectivity, which serves as a
communicating channel.
If you plan to install your camera to a designated location, and will use your home Wi-Fi network to
connect your mobile device, test whether your selected monitoring areas have good Wi-Fi signal
strength. Adjust the direction and distance between your camera, mobile device and Wi-Fi router until
you have identified a suitable location with good connection.
Note:
Depending on surroundings and obstructing factors, such as the effect distance and internal walls
have on signal strength, you may experience reduced Wi-Fi signal.
Disclaimer and Limitation of Liability Online Manual
Customer Support
Technical Specications
Warranty
FCC and IC regulations
Notes:
Check for reception strength and the camera viewing angle before drilling the holes.
The types of screws and anchors you need depend on the composition of the wall. You may need to
purchase the screws and anchors separately to mount your camera.
VTech and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook. VTech and its
suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this software. VTech
and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a result of malfunction, dead
battery, or repairs. Be sure to make backup copies of important data on other media to protect against data loss.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
CAN ICES-3 (B)/NMB-3(B)
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment.
Warranty: Please visit our website at vtechphones.com for full details of the warranty provided in your country.
Find the answer to your question on our knowledge-rich
Online Manual. Get assisted at your own pace and learn what
your monitor is capable of.
Scan the QR code to access the Online Manual or
visit help.vtechphones.com/rm9751
Mobile access
Wi-Fi connection
or
1. Place the wall mount
bracket on a wall and then
use a pencil to mark the
top and the bottom holes
as shown. Remove the
wall mount bracket and
drill two holes in the wall
(7/32 inch drill bit).
2. If you drill the holes into a
stud,go to step 3.
If you drill the holes into an
object other than a stud,
insert the wall anchors into
the holes. Tap gently on the
ends with a hammer until the
wall anchors are flush with
the wall.
4. Place the camera on the wall mount bracket. Insert the
mounting studs into the wall mount holes. Then, slide the
camera forwards until it locks securely. Align the holes on
the wall mount bracket with the screws on the wall, and
slide the wall mount bracket down until it locks into place.
3. Insert the
screwsinto the
holes and tighten
the screws until
only 1/4 inch of
the screws are
exposed.
5. You can maximize your camera viewing anglesby
tilting the wall mount bracket.
Hold the camera, and then rotate the knob in an
anti-clockwise direction. This will loosen the joint of
the wall mount bracket.
Tilt your camera up or down to adjust to your
preferred angle. Then, rotate the knob in a
clockwise direction to tighten the joint and secure
the angle.
1
2
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in
a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
WARNING: Changes or modifications to this equipment
not expressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
To ensure safety of users, the FCC has established criteria
for the amount of radio frequency energy that can be
safely absorbed by a user or bystander according to
the intended usage of the product. This product has
been tested and found to comply with the FCC criteria.
The camera shall be installed and used such that parts
of all persons’ body are maintained at a distance of
approximately 8 in (20 cm) or more.
This Class B digital apparatus complies with Canadian
requirement: CAN ICES-3 (B)/NMB-3(B)
Industry Canada
This device contains licence-exempt transmitter(s)/
receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1)
This device may not cause interference. (2) This device
must accept any interference, including interference that
may cause undesired operation of the device.
The term ‘’IC:‘’ before the certification/registration
number only signifies that the Industry Canada technical
specifications were met.
This product meets the applicable Innovation, Science
and Economic Development Canada technical
specifications.
RF radiation exposure statement
The product complies with FCC RF radiation exposure
limits set forth for an uncontrolled environment.
The camera should be installed and operated with a
minimum distance of 8 in (20 cm) between the camera
and all persons’ body. Use of other accessories may not
ensure compliance with FCC RF exposure guidelines. This
equipment complies also with Industry Canada RSS-102
with respect to Canada’s Health Code 6 for Exposure of
Humans to RF Fields.
Full Manual
Comprehensive help
articles on product set
up, operations, Wi-Fi and
settings
Video Tutorials
Walk-throughs on features
and installation such as
mounting the Camera on
the wall.
FAQs & Troubleshooting
Answers to the most
commonly asked questions,
including troubleshooting
solutions.
Visit our Consumer
Support website 24 hours
a day at
help.vtechphones.com/cs
Call our Customer Support
at 1-844-848-8324
(1-844-84-VTECH) [in US]
or 1-888-211-2005
[in Canada] for help.
Please visit our website at
help.vtechphones.com
for full details of the
warranty provided in your
country.
Technology
Channels
Internet Connection
Nominal effective
range
Power requirements
Wi-Fi 2.4GHz 802.11 b/g/n
1-11 (2412 - 2462 MHz)
Minimum Requirement: 1.5 Mbps @ 720p or 2.5 Mbps @ 1080p
upload bandwidth per camera
Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Camera unit power adapter: Output: 5V DC @ 1 A
Credits:
The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.
The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.
The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.
Specifications are subject to change without notice.
© 2022 VTech Communications, Inc.
All rights reserved. 04/22. RM9751HD_QSG_V2
UL STD.
62368-1
CERTIFIED TO
CSA STD.
C22.2 NO.62368-1
CONFORMS TO
What does this limited warranty cover?
The manufacturer of this VTech product, VTech
Communications, Inc. (“VTech”), warrants to the holder of a
valid proof of purchase (“Consumer” or “you”) that the Product
and all accessories provided by VTech in sales package
(“Product) are free from material defects in material and
workmanship, pursuant to the following terms and conditions,
when installed and used normally and in accordance with
operating instructions. This limited warranty extends only to
the Consumer for Products purchased and used in the United
States of America and Canada.
What will VTech do if the Product is not free from defects in
materials and workmanship during the limited warranty period
(“Materially Defective Product”)?
During the limited warranty period, VTech’s authorized service
representative will replace at VTech’s option, without charge,
a Materially Defective Product. If we choose to replace the
Product, we may replace it with a new or refurbished Product
of the same or similar design. VTech will return replacement
products to you in working condition. VTech will retain defective
parts, modules, or equipment. Replacement of the Product, at
VTech’s option, is your exclusive remedy. You should expect the
replacement to take approximately 30 days.
How long is the limited warranty period?
The limited warranty period for the product extends for
ONE (1) YEAR from date of purchase (90 days on products
purchased as Refurbished*). This limited warranty also applies
to replacement Products for a period of either (a) 90 days from
the date the replacement Product is shipped to you or (b)
the time remaining on the original one-year limited warranty
(90-day limited warranty on products that are purchased as
Refurbished*). Whichever is longer.
*Refurbished products purchased from our online store carry a
90-day replacement warranty.
What is not covered by this limited warranty?
This limited warranty does not cover:
1. Product that has been subjected to misuse, accident,
shipping or other physical damage, improper installation,
abnormal operation or handling, neglect, inundation, fire,
water or other liquid intrusion; or
2. Product that has been damaged due to repair, alteration or
modification by anyone other than an authorized service
representative of VTech; or
3. Product to the extent that the problem experienced is caused
by signal conditions, network reliability, or cable or antenna
systems; or
4. Product to the extent that the problem is caused by use with
non-VTech accessories; or
5. Product whose warranty/quality stickers, product serial
number plates or electronic serial numbers have been
removed, altered or rendered illegible; or
6. Product purchased, used, serviced, or shipped for repair
from outside the United States of America or Canada, or used
for commercial or institutional purposes (including but not
limited to Products used for rental purposes); or
7. Product returned without a valid proof of purchase (see item
2 below); or
8. Charges for installation or set up, adjustment of customer
controls, and installation or repair of systems outside the unit.
How do you get warranty service?
To obtain warranty service in the United States of America,
please visit our website at www.vtechphones.com or call
1 (800) 595-9511 for instructions regarding where to return the
Product.In Canada, go to phones.vtechcanada.com or dial 1
(800) 267-7377.
NOTE: Before calling for service, please review the user’s
manual - a check of the Product’s controls and features may
save you a service call.
Except as provided by applicable law, you assume the risk
of loss or damage during transit and transportation and are
responsible for delivery or handling charges incurred in the
transport of Product(s) to the service location. VTech will
return replaced product under this limited warranty to you,
transportation, delivery or handling charges prepaid. VTech
assumes no risk for damage or loss of the Product in transit.
What must you return with the Product to get warranty service?
1. Return the entire original package and contents including the
Product to the VTech service location along with a description
of the malfunction or difficulty; and
2. Include a “valid proof of purchase” (sales receipt) identifying
the Product purchased (Product model) and the date of
purchase or receipt; and
3. Provide your name, complete and correct mailing address,
and telephone number.
Other limitations
This warranty is the complete and exclusive agreement
between you and VTech. It supersedes all other written or
oral communications related to this product. VTech provides
no other warranties for this product. The warranty exclusively
describes all of VTech’s responsibilities regarding the product.
There are no other expressed warranties. No one is authorized
to make modifications to this warranty and you should not rely
on any such modification.
State Law Rights: This warranty gives you specific legal rights,
and you also have other rights which vary from state to state.
Limitations: Implied warranties, including those of fitness for
a particular purpose and merchantantability (an unwritten
warranty that the product is fit for ordinary use) are limited
to one year from date of purchase. Some states do not allow
limitations on how long an implied warranty lasts, so the above
limitation may not apply to you.
In no event shall VTech be liable for any indirect, special,
incidental, consequential, or similar damages (including, but not
limited to lost profits or revenue, inability to use the product, or
other associated equipment, the cost of substitute equipment,
and claims by third parties) resulting from the use of this
product. Some states do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitation or
exclusion may not apply to you.
Please retain your original sales receipt as proof of purchase.
For cETL compliance only
Limited warranty
Mesures de sécurité importantes
La plaque signalétique appliquée est située au bas du socle de l’unité
du bébé.
Lorsque vous utilisez votre appareil, vous devriez toujours suivre
certaines mesures de précaution de base afin de réduire les risques
d’incendie, d’électrocution et de blessures corporelles, dont ceux qui
suivent:
1. Observez toutes les instructions et mises en garde inscrites sur
l’appareil.
2. L’installation par un adulte est requise.
3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur
supérieure à 2 mètres.
4. Ce produit a été conçu pour être un dispositif d’appoint seulement.
Il n’est pas le remplacement d’une supervision responsable et
adéquate par un adulte et ne devrait pas être utilisé comme telle.
5. Ce produit n’est pas conçu pour être utilisé en tant que moniteur
médical.
6. N’utilisez pas cet appareil près de l’eau ni de toute autre source
d’humidité, par exemple, près d’une baignoire, cuve à lessive,
évier de cuisine, dans un sous-sol humide ni près d’une piscine,
dans un soussol humide ou une douche.
7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque
d’explosion pourrait survenir si un mauvais type de pile est utilisé
pour l’unité du parent. La pile ne peut pas être soumise à des
températures extrêmes élevées ou basses et à une faible pression
d’air à haute altitude pendant l’utilisation, l’entreposage ou le
transport. L’élimination de la pile dans le feu ou dans un four chaud,
ou l’écrasement ou le découpage mécanique de la pile peuvent
entraîner une explosion. Laisser la pile dans un environnement à
température extrêmement élevée peut entraîner une explosion
ou la fuite d’un liquide ou d’un gaz inflammable. Une pile soumise
à une pression d’air extrêmement basse peut provoquer une
explosion ou une fuite de liquide ou de gaz inflammable. Éliminer
la pile usagée conformément aux informations du Sceau RBRC.
8. N’utilisez que les adaptateurs inclus avec ce produit. L’utilisation
d’un adaptateur dont la polarité ou la tension serait inadéquate
risque d’endommager sérieusement le produit et mettre votre
sécurité en péril.
Informations sur les adaptateurs électriques :
Adaptateur de l’unité du bébé: Sortie : 5 V CC 1A.
VTech Telecommunications Ltd.
Mole : VT05EUS05100
9. Lorsqu’ils sont branchés dans une prise de courant, les adaptateurs
secteur ont été conçus pour être orientés correctement, soit à la
verticale ou au plancher. Les broches n’ont pas été conçues pour
supporter le poids du bloc d’alimentation et le maintenir en place
si celuici est branché dans une prise au plafond, sous une table ou
dans un meuble.
10. Pour les appareils raccordés, la prise de courant (de l’adaptateur
secteur) doit être installée près de l’équipement et doit être
facilement accessible.
11. Débranchez ce produit de la prise de courant avant de procéder
au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un
chiffon humide pour le nettoyer.
12. Ne coupez pas les cordons d’alimentation pour remplacer les
fiches, car ceci peut présenter un danger potentiel.
13. Ne laissez aucun objet reposer ni appuyer sur le cordon
d’alimentation. N’installez pas cet appareil dans un endroit où
l’on risque d’écraser le cordon d’alimentation ou de le piétiner.
14. Ne faites fonctionner cet appareil qu’avec le type d’alimentation
indiqué sur l’étiquette. Si vous ne connaissez pas le type
d’alimentation que vous possédez à votre domicile, consultez votre
marchand ou votre compagnie locale d’électricité.
15. L’équipement doit être fourni à partir d’un acquiescement gauche
identifié d’USB aux conditions de la source d’énergie limitée.
16. Ne surchargez pas les prises de courant murales ni les rallonges
électriques.
17. Ne placez pas cet appareil sur un chariot, meuble, trépied, support
de montage ni table chancelants.
18. Les trous et ouvertures du boîtier, situés à l’arrière de l’appareil
ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de
surchauffer, ne bloquez sous aucun prétexte ces ouvertures
et n’empêchez pas l’aération adéquate de l’appareil en le
plaçant sur un lit, divan, tapis ou toute autre surface similaire.
De même, ne le positionnez pas à proximité ni au-dessus d’une
source de chaleur ou d’un calorifère. De plus, ne placez pas
l’appareil dans un endroit avant de vous assurer qu’il y ait une
bonne circulation d’air.
19. N’enfoncez jamais d’objets à travers les ouvertures de cet appareil,
car ils pourraient entrer en contact avec des points de tension
dangereux ou causer des courts-circuits qui peuvent dégénérer
en incendies ou en risques d’électrocution. Ne renversez jamais
de liquide dans ce produit.
20. Afin de réduire les risques d’électrocution, ne démontez pas cet
appareil, mais apportez-le dans un centre de service autorisé.
L’ouverture du boîtier ou le retrait de toutes pièces que contient
cet appareil, à l’exception de l’accès autorisé à certaines portes
ou ouvertures, risque de vous exposer à des points de tension
dangereux ou d’autres dangers. Un remontage incorrect peut par
la suite présenter des risques d’électrocution.
21. Vous devriez tester la réception chaque fois que vous mettez
l’appareil en fonction.
22. Examinez les composantes afin de vérifier si celles-ci ne sont pas
endommagées.
23. Il existe un très faible risque de perte de confidentialité avec
certains appareils électroniques (autres écoute-bébés, téléphones
sans fils etc.). Pour l’éviter, s’assurer que le produit n’a jamais été
utilisé avant l’achat, réinitialiser l’unité de façon périodique, éteindre
l’écoute-bébé quand il n’est pas en cours d’utilisation.
24. Les enfants devraient être supervisés afin de vous assurer qu’ils ne
jouent pas avec l’appareil.
25. Les petites pièces de ce moniteur peuvent être avalées par les
bébés ou les petits enfants. Veuillez tenir ces pièces hors de
portée des enfants.
26. Le produit n’est pas conçu pour être utilisé par des personnes
(incluant des enfants) aux capacités physiques, sensorielles
ou mentales réduites ou qui manquent d’expérience et de
connaissances, à moins qu’on leur ait donné suffisamment de
supervision ou d’instructions relativement à l’utilisation de l’appareil
par une personne responsable de leur sécurité.
CONSERVEZ CES INSTRUCTIONS
Mises en garde
Utilisez et entreposez le produit à une température entre 0˚ C
(32˚F) et 40˚C (104˚ F).
Risque de brûlure, risque d’incendie, risque d’explosion associé à
une mauvaise manipulation de la batterie.
N’exposez pas cet appareil à des froids ou des chaleurs extrêmes,
ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une
source de chauffage.
Avertissement - Risque de strangulation - Les enfants se
sont ÉTRANGLÉS dans des cordons. Gardez ce cordon hors de
portée des enfants (à plus de 0,9 m). N’enlevez pas cette étiquette.
Ne jamais placer le moniteur à l’intérieur du berceau ou du parc
de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec
un article tel une serviette ou une couverture.
D’autres produits électroniques peuvent causer des interférences
auprès de votre caméra IP. Essayez d’installer votre
caméra IP le plus loin possible de ces dispositifs
électroniques : routeurs sans fil, radios, téléphones
cellulaires, interphones, moniteurs de pièces,
téléviseurs, ordinateurs personnels, appareils
électriques de cuisine et téléphones sans fil.
Stimulateurs cardiaques implantés dans l’organisme
Les simulateurs cardiaques (ne s’applique qu’aux dispositifs
numériques sans fil):
L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme
de recherche indépendante, a mené une évaluation pluridisciplinaire
des interférences entre les téléphones sans fil portatifs et les
stimulateurs cardiaques implantés dans l’organisme. Appuyée par
l’Administration des aliments et drogues (FDA) des États-Unis, la firme
WTR recommande aux médecins:
Avis aux détenteurs de stimulateurs cardiaques
Vous devriez maintenir les dispositifs sans fil à au moins six pouces
du simulateur cardiaque.
Ils ne doivent PAS placer le téléphone sans fil directement sur
le stimulateur cardiaque, tel que dans une poche de chemise,
lorsque celui-ci est en marche.
L’étude effectuée par l’organisme WRS n’a pas identifié de risque
pour les détenteurs de simulateurs cardiaques causés par les gens qui
utilisent dispositifs sans fil à proximité de ceux-ci.
Champs électromagnétiques (EMF)
Ce produit de VTech est conforme à toutes les normes se rapportant
aux champs électromagnétiques (EMF) standard. Si vous le manipulez
correctement en suivant les instructions de ce guide, son utilisation
sera sécuritaire pendant de nombreuses années, selon les meilleures
évidences scientifiques dont nous disposons aujourd’hui.
  • Page 1 1
  • Page 2 2

VTech RM9751 Mode d'emploi

Catégorie
Moniteurs vidéo bébé
Taper
Mode d'emploi

dans d''autres langues