Zebra MC33 Mode d'emploi

Marque: Zebra

Modèle: MC33

Taper: Mode d'emploi

Draft 3

3PTY-RFID-TC7X

Regulatory Guide

ZEBRA and the stylized Zebra head are

trademarks of Zebra Technologies Corp.,

registered in many jurisdictions worldwide. All

other trademarks are the property of their

Zebra Technologies | 3 Overlook Point |

Lincolnshire, IL 60069 USA

www.zebra.com

MN-004312-01EN— 10/21

Regulatory Information

This device is approved under Zebra

Technologies Corporation.

This guide applies to the following model

number: 3PTY-RFID-TC7X

All Zebra devices are designed to be

compliant with the rules and regulations

in the locations they are sold and will be

labeled as required.

Local language translation / Tradução do

idioma local / Übersetzung in die lokale

Sprache / Raduccion de idioma local /

Traduction en langue locale / Prijevod na

lokalni jezik / Traduzione in lingua locale

/ 現地語の翻訳 / 현지 언어 번역 /

Перевод на местный язык / 本地語言翻

譯 / 本地语言翻译 / Yerel dil çeviri

/Tłumaczenie na język lokalny :

zebra.com/support

Any changes or modifications to Zebra

equipment not expressly approved by

Zebra could void the user’s authority to

operate the equipment.

Declared maximum operating

temperature: 50°C

For use only with Zebra approved and

UL Listed mobile devices, Zebra

approved, and UL Listed/Recognized

battery packs.

Regulatory Markings

Regulatory markings subject to

certification are applied to the device

signifying the radio(s) is/are approved for

use. Refer to the Declaration of

Conformity (DoC) for details of other

country markings. The DOC is available

at: zebra.com/doc.

Safety in Hospitals and

Aircraft

NOTE: Wireless devices

transmit radio frequency energy

that may affect medical electrical

equipment and aircraft’s operation.

Wireless devices should be switched off

wherever you are requested to do so in

hospitals, clinics, healthcare facilities or

by airline staff. These requests are

designed to prevent possible

interference with sensitive equipments.

RF Exposure Guidelines

Safety Information

Reducing RF Exposure –

Use Properly

Only operate the device in accordance

with the instructions supplied.

The device complies with internationally

recognized standards covering human

exposure to electromagnetic fields. For

information on international human

exposure to electromagnetic fields, refer

to the Zebra Declaration of Conformity

(DoC) at zebra.com/doc.

Use only Zebra tested and approved

headset, belt-clips, holsters, and similar

accessories to ensure RF exposure

compliance. If applicable, follow the

instructions for use as detailed in the

accessory guide.

The use of third-party belt clips, holsters,

and similar accessories may not comply

with RF exposure compliance

requirements and should be avoided.

For further information on the safety of

RF energy from wireless devices, refer

to RF exposure and assessment

standards section at

zebra.com/responsibility.

Handheld or Body-Worn Devices

To satisfy RF exposure requirements,

this device must be hand-held only and,

where applicable, use only with Zebra

tested and approved accessories.

Marking and European

Economic Area (EEA)

Statement of Compliance

Zebra hereby declares that this radio

equipment is in compliance with

Directives 2014/53/EU and 2011/65/EU.

Any radio operation limitations within

EEA countries are identified in Appendix

A of EU Declaration of Conformity. The

full text of the EU Declaration of

Conformity is available at:

zebra.com/doc.

EU Importer: Zebra Technologies B.V

Address: Mercurius 12, 8448 GX

Heerenveen, Netherlands

Waste Electrical and Electronic

Equipment (WEEE)

For EU and UK Customers: For products

at the end of their life, please refer to

recycling/disposal advice at:

zebra.com/weee.

United States and Canada

Regulatory

Radio Frequency Interference

Notices

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) this device

may not cause harmful interference, and

(2) this device must accept any

interference received including

interference that may cause undesired

operation.

NOTE: This equipment has been

tested and found to comply with

the limits for a Class B digital

device, pursuant to Part 15 of the FCC

rules.These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the

user is encouraged to try to correct the

interference by one or more of the

following measures:

•Reorient or relocate the receiving

antenna.

•Increase the separation between the

equipment and receiver.

•Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

•Consult the dealer or an experienced

radio/TV technician for help.

Radio Frequency Interference

Requirements – Canada

Innovation, Science and Economic

Development Canada ICES-003

Compliance Label: CAN ICES-3

([B])/NMB-3([B])

This device complies with Innovation,

Science and Economic Development

Canada’s licence-exempt RSSs.

Operation is subject to the following two

conditions: (1) This device may not

cause interference; and (2) This device

must accept any interference, including

interference that may cause undesired

operation of the device.

L’émetteur/récepteur exempt de licence

contenu dans le présent appareil est

conforme aux CNR d’Innovation,

Sciences et Développement

économique Canada applicables aux

appareils radio exempts de licence.

L’exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne

doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter

tout brouillage radio électrique subi

même si le brouillage est susceptible

d'en compromettre le fonctionnement.

RF Exposure Requirements -

FCC and ISED

The FCC has granted an Equipment

Authorization for this device with all

reported SAR levels evaluated in

compliance with the FCC RF emission

guidelines. SAR information on this

device is on file with the FCC and can be

found under the Display Grant section of

fcc.gov/oet/ea/fccid.

Draft 3

Pour satisfaire aux exigences

d’exposition aux RF, cet appareil doit

être cheville utilisé manuellement

uniquement, le cas échéant, uniquement

utilisé avec les accessoires approuvés et

testés par Zebra.

中国

通过访问以下网址可下载当地语言支持的

产品说明书 zebra.com/support。

（一）符合 “ 微功率短距离无线电发射设

备目录和技术要求 ” 的具体条款和使用场

景，采用的天线类型和性能，控制、调整

及开关等使用方法；

（二）不得擅自改变使用场景或使用条

件、扩大发射频率范围、加大发射功率

（包括额外加装射频功率放大器），不

得擅自更改发射天线；

（三）不得对其他合法的无线电台（站）

产生有害干扰，也不得提出免受有害干扰

保护；

（四）应当承受辐射射频能量的工业、科

学及医疗（ISM）应用设备的干扰或其

他合法的无线电台（站）干扰；

（五）如对其他合法的无线电台（站）产

生有害干扰时，应立即停止使用，并采取

措施消除干扰后方可继续使用；

（六）在航空器内和依据法律法规、国家

有关规定、标准划设的射电天文台、气象

雷达站、卫星地球站（含测控、测距、

接收、导航站）等军民用无线电台

（站）、机场等的电磁环境保护区域内使

用微功率设备，应当遵守电磁环境保护及

Zebra MC33 Mode d'emploi

Marque: Zebra

Modèle: MC33

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Zebra MC33 User guide

Zebra MC33 Mode d'emploi

Zebra MC33 Mode d'emploi

dans d''autres langues

Documents connexes