Ashly CA Series Amplifiers Manuel utilisateur
- Catégorie
- Amplificateurs audio
- Taper
- Manuel utilisateur
Ce manuel convient également à
2
CA Amplifier • Operating Manual
2
CA Amplifier • Operating Manual
Important Safety Instructions •
Consignes de sécurité à lire attentivement
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation point
within an equilateral triangle is intended to alert
the user to the presence of important operating
and maintenance instructions in the literature
accompanying the device.
Le symbole de la flèche dans un triangle équilateral
symbolisant la foudre est prévu pour sensibiliser
l’utilisateur à la présence de tension de voltage
non isolée à l’intérieur de l’appareil. Elle pourrait
constituer un danger de risque de décharge élec-
trique pour les utilisateurs. Le point d’excl mation
dans le triangle équilatérale alerte l’utilisateur de la
présence de consignes qu’il doit d’abord consulter
avant d’utiliser l’appareil.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. To reduce the risk of fire or
electric shock, do not expose
this apparatus to rain or
moisture.
6. Do not use this apparatus near
water.
7. Clean only with dry cloth.
8. Do not block any ventilation
openings. Install in accordance
with the manufacturer’s
instructions.
9. Do not install near any heat
sources such as radiators,
heat registers, stoves, or other
apparatus.
10. Do not defeat the safety
purpose of the polarized or
groundingtype plug. A polarized
plug has two blades with
one wider than the other. A
grounding type plug has two
blades and a third grounding
prong. The wide blade or the
third prong are provided for your
safety. If the provided plug does
not fit into your outlet, consult
an electrician for replacement
of the obsolete outlet.
11. Protect the power cord
from being walked on or
pinched particularly at plugs,
convenience receptacles, and
the point where they exit from
the apparatus.
12. Only use attachments/
accessories specified by the
manufacturer.
13. Use only with the cart, stand,
tripod, bracket, or table
specified by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to avoid
injury from tip-over.
14. Unplug this apparatus during
lightning storms or when
unused for long periods of time.
15. Refer all servicing to qualified
service personnel. Servicing is
required when the apparatus
has been damaged in any way,
such as power-supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
16. This equipment is not suitable
for use in locations where
children are likely to be present.
1. Lisez ces instructions.
2. Conservez ces instructions.
3. Observez les avertissements.
4. Suivez ces instructions.
5. Pour réduire le risque de feu
ou la décharge électrique, ne
pas exposer cet appareil pour
pleuvoir ou l’humidité.
6. Ne pas utiliser l’appareil près de
l’eau.
7. Le nettoyer à l’aide d’un tissus
sec.
8. Ne pas bloquer les ouvertures
de ventilation, installer selon les
consignes du fabricant.
9. Eloigner des sources de chaleur
tel: radiateurs, fourneaux ou
autres appareils qui produisent
de la chaleur.
10. Ne pas modifier ou amputer
le système de la mise à terre.
Une prise avec mise à terre
comprend deux lames dont
une plus large ainsi qu’une mise
à terre: ne pas la couper ou
la modifier. Si la prise murale
n’accepte pas la fiche, consulter
un électricien pour qu’il
remplace la prise désuète.
11. Protéger le cordon de secteur
contre tous bris ou pincement
qui pourraient l’endommager,
soit à la fiche murale ou à
l’appareil.
12. N’employer que les accessoires
recommandés par le fabricant.
13. N’utiliser qu’avec les systèmes
de fixation,chariots, trépied
ou autres, approuvés par le
fabricant ou vendus avec
l’appareil.
14. Débrancher l’appareil lors des
orages électriques ou si inutilisé
pendant une longue période de
temps.
15. Un entretient effectué par un
centre de service accrédité
est exigé si l’appareil a été
endommagé de quelque façon:
si il a été exposé à la pluie,,
l’humidité ou s’il ne fonctionne
pas normalement ou qu’il a été
échappé.
16. Cet équipement ne convient
pas pour une utilisation dans
des endroits où des enfants sont
susceptibles d'être présents.
WARNING: THIS APPARATUS MUST BE GROUNDED (EARTHED)
3
CA Amplifier • Operating Manual
FCC Compliance
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
■This device may not cause harmful
interference
■This device must accept any
interference received, including
interference that may cause undesired
operation
Note: This equipment has been tested
and found to comply with the limits for a
Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed
to provide reasonable protection against
harmful interference in both a commercial
and residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed and
used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no
guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user
is encouraged to try to correct the interference
by one or more of the following measures:
■Reorient or relocate the receiving
antenna.
■Increase the separation between the
equipment and receiver.
■Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
■Consult the dealer or an experienced
radio/TV technician for help.
Unpacking
As a part of our system of quality control,
every Ashly product is carefully inspected
before leaving the factory to ensure flawless
appearance.
After unpacking, please inspect for any
physical damage. Save the shipping carton
and all packing materials, as they were
carefully designed to reduce to a minimum the
possibility of transportation damage should the
unit again require packing and shipping. In the
event that damage has occurred, immediately
notify your dealer so that a written claim to
cover the damages can be initiated.
The right to any claim against a public
carrier can be forfeited if the carrier is not
notified promptly and if the shipping carton
and packing materials are not available for
inspection by the carrier. Save all packing
materials until the claim has been settled.
About Ashly
Ashly Audio was founded in 1974 by a
group of recording engineers, concert sound
professionals, and electronics designers. The
first products were elaborate custom consoles
for friends and associates, but business quickly
spread to new clients and the business grew.
The philosophy we established from the
very beginning holds true today: to offer only
the highest quality audio tools at an affordable
cost to the professional user − ensuring
reliability and long life. Years later, Ashly
remains committed to these principles.
Ashly’s exclusive five-year, worry-free
warranty remains one of the most generous
policies available on any commercial- grade
product. The warranty covers every product
with the Ashly brand name, and is offered at no
extra cost to you.
Please read this entire manual to fully
understand the features and capabilities of this
product.
1 Introduction
Thank you for your purchase of this Ashly CA
power amplifier. This product uses state of the
art, light weight, high power, high efficiency
switching technology developed through
years of design and testing. CA amplifiers are
available in three power levels, designed to
meet the most demanding live sound and fixed
installation sound systems in stadiums, arenas,
performance venues, worship spaces and
convention centers.
1.2 Features
• Two or four channel models
• 500W, 1,000W, or 1,500W per channel
models
• Active power factor correction (PFC)
• Low impedance output (to 2 Ohm)
• Direct 70V or 100V output
• Extremely efficient and lightweight
• Neutrik® Combo XLR - 1/4" jack and
Euroblock input connectors
• Euroblock speaker output connectors
• Front panel soft-power switch, defeatable
• Front panel level controls, fully off = mute,
defeatable
• Front panel LEDs for clip/mute, signal,
current, temperature, bridge mode, protect,
and front panel disable
• 80Hz 2nd order hi-pass filter per channel
(on/off)
• Clip limiter per channel (on/off)
• Input gain settings per channel: 26dB,
32dB, 38dB, or 1.4V
• Remote DC level control per channel
• Remote standby contact closure, with
polarity setting
• Universal 100-240VAC operation, 50-60Hz,
detachable AC connector
• Continuously variable cooling fan(s)
• Protection: Inrush current limitation, over-
temperature, output short-circuit/over-
power, output DC, mains fuse
• Safety/Compliance: cTUVus, CE, FCC Class
B, RoHS
• Ashly five year warranty
2 Requirements
Before connecting to AC mains power, make
sure that the mechanical installation, cooling
requirements, wiring, and controls are all set to
the configuration needed for your application.
Failure to do so could result in damage to the
unit or to other components in the system.
2.1 AC Mains
This amplifier uses a universal Switch Mode
Power Supply (SMPS) with active Power Factor
Correction (PFC). The power supply will auto-
detect nominal AC mains voltage from 100 to
240VAC, 50-60Hz.
Use only the provided AC cord to connect to AC
mains.
4
CA Amplifier • Operating Manual
Table of Contents
1 Introduction .................. 4
2 Requirements ................ 4
2.1 AC mains ....................... 4
2.2 Input wiring .................... 5
2.3 Speaker wire ...................5
2.4 Remote control wire ....... 5
2.5 Mechanical .................... 5
2.6 Cooling .......................... 6
3 Amplifier Protection ....... 6
4 Front Panel Features ...... 7
4.1 Air vents ......................... 7
4.2 Channel LED indicators .. 7
4.3 Protect LED .................... 7
4.4 Disable LED .................... 7
4.5 Channel attenuators ...... 7
4.6 Bridge LED ...................... 7
4.7 Power switch/LED .......... 7
4.8 Model number ................ 7
4.9 Mounting holes .............. 7
5 Rear Panel Features ....... 8
5.1 Standby connector ........ 8
5.2a Standby polarity ............ 8
5.2b Front panel disable ........ 8
5.3a DIP switch (HPF) .............8
5.3b DIP switch (limiter) .......... 8
5.3c DIP switch (gain) .............8
5.4 Euroblock input jack ........8
5.5 Remote DC level control ..8
5.6 Bridge mode switch ......... 8
5.7 Combo input jacks ...........9
5.8 Speaker outputs ..............9
5.9 AC mains .........................9
6 Troubleshooting ............ 9
7 Specifications ....... 10-11
8 Warranty .................... 12
All CA models have a fixed, non-defeatable
warm-up delay of two seconds to protect
against excessive in-rush current when first
powered up. The model number and power
consumption are indicated on the back panel
label placed near the AC inlet. To reduce the
risk of ground loop hum, all sound system
ground references should originate at the
same AC power distribution point. Do not lift or
remove the amplifier power cord ground pin.
2.2 Input Signal Wire
Use shielded wiring for balanced or unbalanced
audio signals. Shielding which is properly
grounded will protect the signal from outside
electrical interference such as RF, fluorescent
lighting, and computer/display emissions.
Unbalanced or single-ended (tip-sleeve) lines
of less than 10 feet are generally ok, but for
greater distance or noisy field environments,
use balanced input signal wiring.
Each channel's Euroblock, 1/4" phone jack,
and XLR inputs are wired in parallel, with
XLR pin 2 (+) and pin 3 (-). When using an
unbalanced input, wire the signal to the input
(+) Euroblock pin, phone jack tip, or XLR pin 2,
and also be sure to wire the input (-) pin, phone
jack ring, or XLR pin 3 to ground. Do not leave
the (-) input unconnected. Avoid running low
level signal wires in close proximity or parallel
to long speaker cables, AC power cables, or
power transformers, as they can induce hum or
oscillation.
2.3 Speaker Wire
Note: The sound system installer is responsible
for using loudspeaker wiring that is in
compliance with local electrical code. The
following recommendations for speaker wiring
are based on UL 60065 section 5.2-d and the
US National Electrical Code Article 725. These
are only guidelines, consult your local code for
specific up to date requirements.
• Class 2 wiring is typically used when the
maximum measured open-circuit speaker
output voltage is less than 120V rms.
• Class 3 wiring is typically used if the
measured open circuit output voltage
exceeds 120V rms, such as when
amplifiers are used in bridged mode.
See the specifications for specific model
configurations that may require Class 3
speaker wiring.
Speaker wire gauge: CA amplifiers are capable
of delivering high levels of output current, so
the wire gauge used for speaker outputs is
important. Inadequate wire gauge, especially
over long distance, adds significant resistance
to the speaker’s own impedance, reducing
the power which is actually delivered to the
speaker. It could also result in a decreased
damping factor and potential fire hazard. Since
power at the speaker load is of primary concern
in system design, refer to the table below to
best determine appropriate wire gauge for your
application.
The following table lists the resistance per 100
feet of common copper wire gauges, and also
lists the percentage of the speaker load power
which would be lost as heat in an arbitrary
100 ft run of different gauges of 2-conductor
copper speaker wire.
This table expresses the power loss as a
percentage of the load’s power rather than
the total amplifier output power in order to
accurately determine power loss at other cable
lengths. For example, if you plan to deliver 150
watts to an 8 Ohm load through 50 ft of 14 ga.
cable, the power loss in the cable would be
half that of a 100 ft run of #14 wire as shown
in the table, or 1.6% of 150W, which is an
insignificant 2.4 watts. However, if you were
to run 200 ft of 18 ga. cable to a 2 Ohm load,
the loss would be twice that of the 100 ft run
shown in the table, or 65.2% of 250W, which is
163 watts lost as heat. Always be sure to use
adequate gauge speaker wire.
Wire
Gauge
Ohms
/100ft
8Ω
load
4Ω
load
2Ω
load
#8 0.0605Ω 0.8% 1.5% 3%
#10 0.1018Ω 1.3% 2.5% 5%
#12 0.1619Ω 2.0% 4.0% 8%
#14 0.2575Ω 3.2% 6.4% 12.8%
#16 0.4094Ω 5.1% 10.2% 20.4%
#18 0.6510Ω 8.1% 16.3% 32.6%
5
CA Amplifier • Operating Manual
2.4 Remote Control Wire
• Remote DC level control - Bell or telephone
wire is sufficient for DC level control, as well as
CAT5 cable. The V+ and Ground pins from one
amplifier channel can be shared with other
remote DC level controls wired to the same
amplifier, however do not connect remote
control ground to any external grounds.
• Remote Standby - This is a logic level
signal, use low gauge wire, shielding is
unnecessary.
2.5 Mechanical
Each amplifier model is 2RU and is designed to
fit into a 19-inch equipment rack with minimum
depth of 16.1" (409mm). Use four screws
when mounting the amplifier to the front rack
rails. Rear support is recommended for mobile
or touring use. In some installations where the
sound system is exposed to a high level of RF
noise or system-induced oscillation, it may be
necessary to ground the amplifier’s chassis
to the rack enclosure. This is accomplished
using star type lockwashers on the four
rack mounting screws, placed between the
amplifier chassis and the rack rails. These star
washers will penetrate through the amplifier
and rack rail finish to adequately ground the
chassis to the rack.
2.6 Cooling
Air vents on the amplifier front and side
panels must have access to free flowing room
temperature air. Cool air is drawn in through the
front panel and blown out through the sides.
It is not necessary to leave empty rack spaces
above or below the amplifier. See specifications
for amplifier thermal output characteristics in
BTU/hr.
3 Amplifier Protection
Power-On Delay: All models have a two second
turn-on delay to prevent excessive in-rush
current when first powered on.
Thermal Protection: Cooling fans are
continuously variable, reaching their maximum
speed when an amplifier channel reaches 80%
of it's safe operating temperature. Temp LEDs
turn on when signal limiting countermeasures
are being applied to that channel due to over
temperature conditions.
Overpower Protection: To protect internal
components against overpower conditions,
a protection scheme in each output stage
reduces audio output power until the fault
condition is no longer present.
Output DC and Rail Fault Protection: Output
DC on any channel will trigger the Protect LED
and mute that channel.
AC Mains: If the AC Mains line voltage exceeds
or falls below the specified operating range,
the amplifier will temporarily shut down. It will
automatically restart as soon as the AC line
voltage returns to the specified range.
For details on these and other amplifier
protection schemes, plus their LED codes, refer
to the troubleshooting section.
6
CA Amplifier • Operating Manual
4 Front Panel Features CA-1.54 shown
The exception to this is when the amp shuts
down due to the AC mains voltage being out
of range, in which case the amp automatically
restarts as soon as the AC mains line voltage
returns to the specified operating range.
4.4 Disable LED
This yellow LED lights when the power switch
and level controls have been disabled using the
back panel DIP switch (sec. 5.2b).
4.5 Channel Attenuators
These control the level of the amplifier, and work
in combination with the remote DC level controls.
When an input attenuator is turned fully off, the
red Clip/Mute LED for that channel turns on to
indicate mute status. Front panel attenuators and
the power switch can be disabled using the back
panel DIP switch (sec. 5.2b).
4.6 Bridge LED
This green LED indicates when a channel pair
is set to BRIDGE mode from the back panel
switch (sec. 5.6). In bridge mode, only the
odd numbered input and level control for that
channel pair is used.
4.7 Power Switch/LED
This switch is used for powering the amplifier
on or off. Its white LED lights solid when the
amplifier is on and flashes at 1Hz when in
standby mode. The power switch can be
disabled using the back panel DIP switch. The
three possible power switch LED conditions are:
• Fully lit: The amplifier is powered up, even
if the power switch has been disabled, in
which case the disable LED will be on.
• Flashing: The amplifier is in standby mode.
• Fully off: The amplifier is completely off.
4.8 Model Number
The first two numbers of model number express
the power rating per channel of the amplifier.
For example, "1.5" mean 1,500W per channel,
"1.0" means 1,000W per channel, and "50"
means 500 W per channel. The last number is
the channel count.
4.9 Mounting Holes
For mounting to a 19" equipment rack.
4.1 Air Vents
Cool air enters in through the amplifier front
panel and is vented out the sides.
4.2 Channel LED Indicators
•
CLIP/MUTE (red):
CLIPPING is indicated when the speaker
output reaches 95% (-0.5dB) of maximum
power.
MUTE is indicated when front panel level or DC
level controls are fully attenuated.
The Clip/Mute LED is also used with the Protect
LED to indicate output DC fault. See the
troubleshooting section for LED fault codes.
• SIGNAL (green) is indicated when amplifier
output voltage reaches 25% (-12dB) of
maximum.
• CURRENT (green) indicates when output
current delivered to the speaker load is 2
Amp or greater.
• TEMP (yellow) indicates that automatic
counter-measures are being applied due to
an excessive internal temperature .
4.3 Protect LED
The red protect LED initially turns on to indicate
that real-time countermeasures are being applied
to overpower, over-temperature, or rail voltage
fault conditions while the amp is still running.
If the countermeasures are unsuccessful and
the amplifier protects itself by shutting down,
the protect LED remains on and the amplifier's
power must be cycled before resuming normal
operation.
7
CA Amplifier • Operating Manual
5 Rear Panel Features CA-1.54 shown
5.3b Limiter
The clip limiter is used to prevent the amplifier
channel from sending clipped audio to the
speaker. When the clip limiter is enabled,
input signal level is automatically turned down
whenever full output power is exceeded.
5.3c Gain
The Amplifier Gain settings are used to set the
overall voltage gain of the amplifier in dB. This
is useful when matching an amplifier to input
signal strength. Using the maximum expected
input signal level, set amplifier gain to the
highest setting possible without risk of the
amplifier going into clipping. The Gain setting
of 1.4V means a 1.4V input signal will drive the
amp to full output.
5.4 Euroblock Input Jack
Used for wiring a balanced input. Euroblock
connectors and 1/4" TRS/XLR combo jacks are
internally wired in parallel. If using an unbalanced
signal source on the Euroblock connector, wire its
input signal to the (+) pin, shield to (G), and also
wire the (-) input pin to ground.
5.5 Remote DC Level Control
Each channel has a
potentiometer circuit available
on a Euroblock connector for
remote DC level control of that
channel. The illustration to
the right shows proper wiring.
There is no limit to wire length.
Do not use any other ground source. If multiple
remote DC level controls are used for different
channels, the same ground and V+ sources can
be shared.
5.6 Bridge Mode Switch
This switch, when pressed in, places the
adjacent channel pair into bridge mode,
combining two amplifier outputs for more power
to a single speaker load. Bridge mode uses
only the odd numbered input and level control,
disabling the even numbered input and level
control for that channel pair. Speaker outputs
in bridge mode must be wired differently, as
shown on the back of the amplifier. A bridge
mode switch button can be removed for added
security by pulling it straight off.
5.1 Standby Connector
This Euroblock connector is used for remote
contact closure control of amplifier standby
status, which places the amplifier into a low
power consumption state. A DIP switch sets
standby circuit polarity.
5.2 Standby Polarity & Front Panel
Disable DIP Switch
5.2a Standby Polarity
The Standby Polarity
DIP switch sets the
polarity requirement
for placing the
amplifier into standby.
When standby polarity
is set High, the amp
goes into standby
whenever the circuit is open. When standby
polarity is set Low, the amp goes into standby
whenever the circuit is closed.
5.2b Front Panel Disable
The Front Panel Disable DIP switch de-
activates all front panel controls.
5.3 DIP Switch Channel Settings
Each channel has its own DIP switch for
independently
setting 80Hz Hi-
Pass Filter, Clip
Limiter, and Gain as
described below:
5.3a High Pass Filter
An 80Hz 2nd order hipass filter is used to reduce
low frequency content going to a speaker.
8
CA Amplifier • Operating Manual
(rear panel features continued)
5.7 Combo Input Jack
The combination 1/4" TRS and XLR jack (pin 2
hot) is wired in parallel to the Euroblock input.
Do not float the TRS ring or XLR pin 3, connect
it to (-) signal or to ground (if unbalanced).
5.8 Speaker Output Connectors
7.62mm Euroblock connectors are used for
convenient and secure wiring to speaker
loads. Bridge mode uses the center two pins as
indicated on the amplifier back panel.
5.9 AC Mains Connector
Always use the AC cord provided by Ashly for
connecting to mains power. The amplifier auto-
detects nominal mains voltage from 100VAC to
240VAC. WARNING: Do not remove or lift the
mains connector ground.
5.10 Serial Number Sticker
This sticker identifies the product model
number, serial number, and AC mains current/
power rating.
6 Troubleshooting
No AC Power
• Is the detachable AC power cord properly
installed? Is it plugged into a known live
outlet?
• Has the power switch been disabled?
No Amplifier Output
• Is the amplifier in Standby Mode?
• Is there signal getting to the amplifier?
• Is the input signal properly wired?
• Are output connectors properly wired?
• Are front panel or remote control attenuators
turned down?
• Is the Amplifier in Protect Mode? (see table
below)
Attenuators Don't Work
• Have the front panel controls been disabled
using the rear panel DIP switch?
Still Not Working?
• Contact Ashly technical support at 1-800-
872-0010 x124, or email service@ashly.com
Protect Mode - Front Panel LED Error Codes:
Protect Mode Fault Description Power Protect Clip/Mute Signal Temp Current
>9dB Continuous Power Limiting On
Amp Power Module Channel Protect On
†Thermal Protect On
††Power Supply Out Of Range On
*Amp Channel DC Protect On
*Amp Channel Over-Temperature On
*Power Transformer Over-Temperature
On
*Power Supply Rails Too High On
*Micro-Controller Over-Temperature On
†Thermal Protect Standby
††
Power Supply Out Of Range
Standby
*Amp Channel DC Protect Standby
*Amp Channel Over-Temperature Standby
*Power Transformer Over-Temperature
Standby
*Power Supply Rails Too High Standby
*Micro-Controller Over-Temperature Standby
† Amp still passes audio, automatic recovery
†† Amp mutes until fault clears, automatic recovery
* Non-recoverable fault, must reset Amp by cycling AC power
9
CA Amplifier • Operating Manual
7 Specifications
General Power Amplifier Specifications (0dBu = 0.775V rms)
Amplifier Model CA1.54 CA1.52 CA1.04 CA1.02 CA504 CA502
Maximum Output Power - in Watts
CEA-2006/490A, 20ms 1kHz 1%THD+N, 480ms 1kHz -20dB, 120VAC, all channels driven at rated load
Low Z output, per channel
2 Ohm 1500 1500 1000 1000 500 500
4 Ohm 1500 1500 1000 1000 500 500
8 Ohm 750 750 500 500 250 250
Low Z output, per bridged channel pair*
4 Ohm 3000* 3000* 2000* 2000* 1000* 1000*
8 Ohm 3000* 3000* 2000* 2000* 1000* 1000*
70V/100V* output
70V 1500 (direct) 1500 (direct) 1000 (direct) 1000 (direct) 1000* (bridged) 1000* (bridged)
100V 3000* (bridged) 3000* (bridged) 2000* (bridged) 2000* (bridged) 1000* (bridged) 1000* (bridged)
*May require Class 3 speaker wiring, all others use Class 2 wiring. See section 2.3
Total Power Draw - in Watts, all channels driven, 1/8 power sinewave
Standby 22 13 19 10 17 8
Idle (no signal) 100 31 70 40 34 17
1/8 max power 975 485 675 335 345 172
Total Current Draw - in Amps, all channels driven, 1/8 power sinewave, 120VAC (divide by 2 for 240VAC)
Standby mode 0.39 0.24 0.37 0.21 0.35 0.2
Idle (no signal) 0.68 0.36 0.64 0.34 0.5 0.27
1/8 max power 8.9 4.2 6 3 3 1.5
Total Thermal Dissipation - in BTU/hour with typical input, all channels driven, 120VAC
Standby mode 76 44 65 32 57 28
Idle (no signal) 209 105 184 96 115 57
1/8 max power, 4 Ohm 648 314 474 229 266 120
1/8 max power, 2 Ohm 754 355 576 269 304 148
Input Sensitivity - in Volts(rms) and dBu, per back panel DIP Switch gain settings
@26dB gain 3.87V
(+14.0dBu)
3.87V
(+14.0dBu)
3.16V
(+12.2dBu)
3.16V
(+12.2dBu)
2.24V
(+9.2dBu)
2.24V
(+9.2dBu)
@32dB gain 1.94V
(+8.0dBu)
1.94V
(+8.0dBu)
1.58V
(+6.2dBu)
1.58V
(+6.2dBu)
1.12V
(+3.2dBu)
1.12V
(+3.2dBu)
@38dB gain 0.97V
(+2.0dBu)
0.97V
(+2.0dBu)
0.79V
(+0.2dBu)
0.79V
(+0.2dBu)
0.56V
(-2.8dBu)
0.56V
(-2.8dBu)
@1.4V gain 1.4V
(+5.1dBu)
1.4V
(+5.1dBu)
1.4V
(+5.1dBu)
1.4V
(+5.1dBu)
1.4V
(+5.1dBu)
1.4V
(+5.1dBu)
10
CA Amplifier • Operating Manual
Distortion (SMPTE, typical) <0.5%
Distortion (THD-N, typical, 8 Ohm,
10dB below rated power, 20Hz-20kHz
<0.5%
Signal to Noise, 26dB input sensitivity,
20Hz-20kHz, unweighted
>98dB (50x models),
>101dB (1.0x models),
>103dB (1.5x models)
Frequency Response 20Hz-20kHz, +/-0.05dB
Channel Separation
(dB from full output, 1kHz)
-75dB
Damping Factor (8 Ohm load, <1kHz) >250
Balanced Input Connector (per channel) Euroblock (3.5mm),
1/4" TRS and XLR Combo jack
Input Impedance 10k Ohm
Maximum Input Level +21dBu
Bridge Mode Switch
(per channel pair)
In for bridged mode,
Out for stereo
Remote DC Level Control
(G, CV, V+ per channel)
Euroblock (3.5mm), V+ is fully
on, G is fully attenuated
DIP Switch settings (per channel)
Switches 1-2: Input Gain 26dB, 32dB, 38dB, 1.4V
Switch 3: Output Clip Limiter On, Off
Switch 4: Input High Pass Filter 80Hz 2nd order HPF - On, Off
DIP Switch settings (global)
Switch 5: Front Panel Disable On, Off
Switch 6: Standby Polarity High (standby when open), Low
(standby when closed)
Standby Contact Closure Euroblock (3.5mm)
Speaker Output Connector Euroblock (7.62mm)
Front Panel Indicators
Power Switch LED (white) On, Off, Standby (flashing)
Clip/Mute LED (red) On at 95% max output
(0.5dB below max), Mute
Signal LED (green) On at 25% max output voltage
(-12dB)
Current LED (green) On at >2 Amps to speaker load
Temp LED (yellow) On when thermal counter-
measures are being applied
Bridge LED (green) Per Channel Pair - On, Off
Protect LED (red) -see troubleshooting
section for protect LED error codes
On for fault condition counter-
measures or shut-down, Off
Disable LED (yellow) On when front panel controls are
disabled, Off
Attenuators Per channel: front panel,
Fully off = Mute
Remote Control Options WR-1, WR-1.1 DC level control
Amplifier Protection In-rush current, over-
temperature, output DC, output
over-power, AC mains voltage,
mains fuses
Cooling Continuously variable
temperature controlled fan(s)
Power Requirements (50-60Hz)
Nominal Voltage Input 100-240VAC
Operating Range 70-270VAC
Minimum Power-up 70VAC
Power Supply Type SMPS with active PFC
(Power Factor Correction)
AC Mains Line Cord Connector Detachable Nema 5-15 for USA
(may vary for export)
Environmental 32°F-120°F, (0°C-49°C)
noncondensing
Unit Dimensions (all models) 19”W x 3.5”H x 16.1”D
(483 x 89 x 409mm)
Unit Weight by Model CA-502: 15lbs (6.81kg)
CA-504 17.5lbs (7.95kg)
CA-1.02 15.5lbs (7.04kg)
CA-1.04 19.5lbs (8.85kg)
CA-1.52 16lbs (7.26kg)
CA-1.54 20lbs (9.08kg)
Shipping Dimensions (all models) 21.9"W x 5.43"H x 19.3"D
(556mm x 13.8mm x 489mm)
Shipping Weight by Model CA-502 18.5lbs (8.4kg)
CA-504 21.5lbs (9.76kg)
CA-1.02 19.5lbs (8.85kg)
CA-1.04 24.0lbs (10.9kg)
CA-1.52 20.0lbs (9.08kg)
CA-1.54 24lbs (10.9kg)
Safety/Compliance cTUVus, CE, FCC Class B, RoHS
Specifications (continued)
11
CA Amplifier • Operating Manual
CA 4 0823
LIMITED WARRANTY (USA ONLY)
(Other countries please contact your respective
distributor or dealer.)
For units purchased in the USA, warranty service
for this unit shall be provided by ASHLY AUDIO. in
accordance with the following warranty statement.
ASHLY AUDIO, an exertis|JAM business, warrants
to the owner of this product that it will be free from
defects in workmanship and materials for a period
of FIVE years from the original-date-of-purchase,
with the exception of touch-screen displays and
motorized faders which are warrantied for THREE
years from the original-date-of-purchase.
ASHLY AUDIO will without charge, repair or
replace at its discretion, any defective product
or component parts upon prepaid delivery of
the product to the ASHLY AUDIO factory service
department, accompanied with a proof of original-
date-of-purchase in the form of a valid sales receipt.
This warranty gives you specific legal rights, and you
may also have other rights, which vary from state to
state.
EXCLUSIONS: This warranty does not apply in
the event of misuse, neglect, or as a result of
unauthorized alterations or repairs made to the
product. This warranty is void if the serial number
is altered, defaced, or removed. ASHLY AUDIO
reserves the right to make changes in design, or
make additions to, or improvements upon, this
product without any obligation to install the same on
products previously manufactured.
Any implied warranties, which may arise under the
operation of state law, shall be effective only for
FIVE years (THREE years for touch-screen displays
and motorized faders) from the original-date-of-
purchase of the product. ASHLY AUDIO shall be
obligated to only correct defects in the product
itself. ASHLY AUDIO is not liable for any damage or
injury, which may result from, or be incidental to, or
a consequence of, such defects. Some states do not
allow limitations on how long an implied warranty
lasts, or the exclusion, or limitation of incidental or
consequential damages, so the above limitations or
exclusions may not apply to you.
OBTAINING WARRANTY SERVICE:
For warranty service in the United States, please
follow this procedure:
1) Return the product to ASHLY AUDIO, freight
prepaid, with a written statement describing the
defect and application that the product is used in.
ASHLY AUDIO will examine the product and perform
any necessary service, including replacement of
defective parts, at no further cost to you.
2) Ship your product to:
ASHLY AUDIO
Attention: Service Department
847 Holt Road
Webster, NY 14580-9103
ASHLY AUDIO 847 Holt Road Webster, NY 14580-9103, USA
Phone: (585) 872-0010 Fax: (585) 872-0739
Toll Free (800) 828-6308 www.ashly.com
©2020 Ashly Audio. All rights reserved worldwide.
All features, specifications, and graphical representations are subject to change or improvement without notice.
12
CA Amplifier • Operating Manual
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ashly CA Series Amplifiers Manuel utilisateur
- Catégorie
- Amplificateurs audio
- Taper
- Manuel utilisateur
- Ce manuel convient également à