IKEA DW60 Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur
RENLIG
DW60
GB
DE
FR
IT
ENGLISH 4
DEUTSCH 24
FRANÇAIS 46
ITALIANO 68
Contents
Safety information 4
Product description 5
Control panel 6
Washing programmes 8
Use of the appliance 9
Setting the water softener 9
Use of dishwasher salt 10
Use of rinse aid 11
Loading cutlery and dishes 12
Use of detergent 13
Setting and starting a washing programme
14
Care and cleaning 15
What to do if… 17
Technical data 18
Installation 19
Water connection 19
Electrical connection 20
Environment concerns 21
IKEA GUARANTEE 21
Subject to change without notice
Safety information
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep these
instructions with the appliance even if you
move or sell it. Users must fully know the oper-
ation and safety features of the appliance.
Correct use
The appliance is designed exclusively for
domestic use.
Only use the appliance to clean household
utensils that are applicable for dishwashers.
Do not put solvents in the appliance. Risk of
explosion.
Put the knives and all items with sharp points
in the cutlery basket with their points down.
If not, put in a horizontal position in the up-
per basket.
Use only branded products for dishwashers
(detergent, salt, rinse aid).
If you open the door while the appliance is
in operation, hot steam can escape. Risk of
skin burns.
Do not remove dishes from the dishwasher
before the end of the washing programme.
When the washing programme is comple-
ted, disconnect the mains plug from the
mains socket and close the water tap.
Only an authorised service engineer can re-
pair this appliance. Use only original spare
parts.
Do not do repairs yourself to prevent injury
and damage to the appliance. Always con-
tact your local After Sales Service.
General safety
Persons (including children) with reduced
physical sensory, mental capabilities or lack
of experience and knowledge must not use
the appliance. They must have supervision
or instruction for the operation of the appli-
ance by a person responsible for their safe-
ty.
Obey the safety instructions from the man-
ufacturer of the dishwasher detergent to
prevent burns to eyes, mouth and throat.
Do not drink the water from the dishwasher.
Detergent residues can stay in your appli-
ance.
Always close the door when you do not use
the appliance to prevent injury and not to
stumble over the open door.
Do not sit or stand on the open door.
Child safety
Only adults can use this appliance. Children
must get supervision to make sure that they
do not play with the appliance.
Keep all the packaging away from children.
There is a risk of suffocation.
Keep all detergents in a safe area. Do not
let children touch the detergents.
Keep children away from the appliance
when the door is open.
ENGLISH 4
Installation
Make sure that the appliance is not dam-
aged because of transport. Do not connect
a damaged appliance. If necessary, contact
the supplier.
Remove all packaging before first use.
A qualified and competent person must do
the electrical installation.
A qualified and competent person must do
the plumbing installation.
Do not change the specifications or modify
this product. Risk of injury and damage to
the appliance.
Do not use the appliance:
– if the mains cable or water hoses are
damaged,
if the control panel, worktop or plinth area
are damaged, that you can get access to
the inner side of the appliance.
If you have any doubts, please contact your
After Sales Service. Refer to the list of the
After Sales Services at the end of user man-
ual.
Do not drill into the sides of the appliance to
prevent damage to hydraulic and electrical
components.
Warning! Carefully obey the instructions
for electrical and water connections.
Product description
1
2
3
4
5
6
7
8
9
1 Upper basket
2 Water hardness dial
3 Salt container
4 Detergent dispenser
5 Rinse aid dispenser
6 Rating plate
7 Filters
8 Lower spray arm
9 Upper spray arm
ENGLISH 5
Control panel
1 2 3
5 4
A B
1 On/off button
2 Half-load button
3 Programme selection/cancel button (SELECT/CANCEL)
4 Indicator lights
5 Programme indicator lights
Indicator lights
The indicator light comes on when the washing
programme is completed. Auxiliary functions:
Level of the water softener.
Activation/deactivation the audible signals.
An alarm if the appliance has a malfunction.
1)
The indicator light comes on when it is neces-
sary to fill the rinse aid. Refer to the chapter
'Use of rinse aid'.
1)
The indicator light comes on when it is neces-
sary to fill the salt container. Refer to the chap-
ter 'Use of dishwasher salt'.
The salt indicator light can stay on for some
hours, but it does not have an unwanted effect
on the operation of the appliance.
1) The indicator light is off while a washing programme operates.
ENGLISH 6
Programme selection/cancel button
Use the programme selection/cancel button
for these operations:
To set the washing programme. Refer to the
chapter 'Setting and starting a washing pro-
gramme'.
To set the water softener. Refer to the chap-
ter 'Setting the water softener'.
To deactivate/activate the audible signals.
Refer to the section 'Audible signals'.
To cancel a washing programme in pro-
gress. Refer to the chapter 'Setting and start-
ing a washing programme'.
Half-load button
The half-load option is not available for all
washing programmes. Refer to the chapter
'Washing programmes'.
Load dishes in the upper and lower basket.
Decrease the detergent dosage when you
use the half-load option.
Press the half-load button to set the option.
The half-load indicator light comes on,
when the half-load option is selectable.
With the half-load button pressed the
time duration and the consumption of wa-
ter and energy are reduced.
Setting mode
The appliance is in setting mode when all the
programme indicator lights are off and the end
indicator light flashes.
The appliance must be in setting mode for
these operations:
To set a washing programme.
To set the water softener level.
To deactivate/activate the audible signals.
If a programme indicator light is on, cancel the
programme to go back to the setting mode.
Refer to the chapter "Setting and starting a
washing programme".
Programme indicator lights A and B
Apart the selection of the corresponding wash-
ing programme, these lights have an auxiliary
functions:
The adjustment of the water softener level.
Deactivation/activation of the audible sig-
nals.
Audible signals
You can hear an audible signal:
At the end of the washing programme.
When the appliance has a malfunction.
The activation of the audible signals is set at
the factory.
Do these steps to deactivate the audible sig-
nals:
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press and hold the programme selection/
cancel button until programme indicator
light A flashes and programme indicator
light B comes on.
4. Press the programme selection/cancel
button again.
Programme indicator light A comes on.
– Programme indicator light B starts to
flash.
5. Wait until programme indicator light A
goes off.
Programme indicator light B continues to
flash.
The end indicator light comes on.
The audible signals are activated.
6. Press the programme selection/cancel
button again.
The end indicator light goes off.
The audible signals are deactivated.
7. Switch off the appliance to save the oper-
ation.
Do these steps to activate the audible signals:
1. Do the above procedure until the end in-
dicator light comes on.
ENGLISH 7
Washing programmes
Washing programmes
Programme
Degree of
soil
Type of load Programme description
Half-load op-
tion
Intensive
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
yes
Normal
Normal soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
yes
Quick
1)
Normal or
light soil
Crockery
and cutlery
Main wash up to 60°C
Final rinse
no
Eco
2)
Normal soil
Crockery
and cutlery
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
yes
Rinse &
Hold
Any
Partial load
(to be com-
pleted later
in the day)
1 cold rinse (to prevent food
scraps to bond).
Detergent is not necessary
with this programme.
no
1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want
to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes. This is the economy washing programme. Please refer to separate leaflet
supplied, for test data. Available only in 3 languages (English, French, German) just for test institutes
purpose.
Consumption values (for full washing cycle)
Programme Programme duration
(minutes)
Energy consumption
(kWh)
Water consumption
(litres)
120-130 1,8-2,0 22-24
105-115 1,5-1,7 23-25
30 0,9 9
1)
130-140 1,0-1,2 14-16
ENGLISH 8
Programme Programme duration
(minutes)
Energy consumption
(kWh)
Water consumption
(litres)
12 0,1 5
1) The duration of this washing programme is prefixed (longer) than the others due to a prolonged drying
and washing phases.
The pressure and temperature of the wa-
ter, the variations of power supply and
the quantity of dishes can change these values.
Use of the appliance
Refer to the following instructions for each step
of procedure:
1. Make a check if the water softener level is
correct for the water hardness in your area.
If necessary set the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dishwash-
er.
5. Set the correct washing programme for the
type of load and soil.
6. Fill the detergent dispenser with the correct
quantity of detergent.
7. Start the washing programme.
If you use detergent tablets, refer to the
chapter 'Use of detergent'.
Setting the water softener
The water softener removes minerals and salts
from the water supply. Minerals and salts can
have bad effect on the operation of the appli-
ance.
Water hardness is measured in equivalent
scales:
German degrees (dH°).
French degrees (°TH).
mmol/l (millimol per litre - international unit
for the hardness of water).
•Clarke.
Adjust the water softener to the water hard-
ness in your area. If necessary, contact your
local water authority.
Water hardness Water hardness setting
°dH °TH mmol/l Clarke manually electronically
51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10
43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9
37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8
29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7
23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6
19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5
15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4
ENGLISH 9
Water hardness Water hardness setting
°dH °TH mmol/l Clarke manually electronically
11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3
4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2
< 4 < 7 < 0,7 < 5
1
1)
1
1)
1) No use of salt required.
You must set the water softener manually
and electronically.
Manual adjustment
The appliance is set at the factory at position
2.
1
2
Set switch to position
1 or 2.
Electronic adjustment
The water softener is set at the factory at
level 5.
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press and hold the programme selection/
cancel button.
4. Release the programme selection/cancel
button when programme indicator light A
starts to flash and programme indicator
light B comes on.
5. Wait until programme indicator light B
goes off.
– Programme indicator light A starts to
flash.
The end indicator light starts to flash.
6. Press the programme selection/cancel
button one time.
– Programme indicator light A starts to
flash.
The setting function of the water softener
is activated.
The end indicator light flashes to show
the level of the water softener.
Example: 5 flashes, pause, 5 flashes,
pause, etc... = level 5.
7. Press the programme selection/cancel
button one time to increase the water soft-
ener level by one step.
8. Press the on/off button to save the opera-
tion.
Use of dishwasher salt
Caution! Only use dishwashers salt.
Types of salt that are not applicable for
dishwashers cause damage to the water
softener.
1 2
ENGLISH 10
3
Fill the salt container
with 1 litre of water
(only the first opera-
tion).
4
Fill the salt container
with 1,5-2,0 kg of
salt. Use the salt fun-
nel supplied.
5
Make sure that there
is no grain of salt out-
er of the salt com-
partment.
6
It is normal that water overflows from the
salt container when you fill it with salt.
Use of rinse aid
Caution! Only use branded rinse aid for
dishwashers.
Do these steps to fill the rinse aid dispenser:
1
2
3
+
-
M
A
X
4
Caution! Do not fill the rinse aid dis-
penser with other products (e.g. dish-
washer cleaning agent, liquid detergent).
There is a risk of damage to the appliance.
ENGLISH 11
Adjusting the dosage of rinse aid
The rinse aid dial is
set at the factory at
position 3.
To increase or de-
crease the dosage
refer to 'What to do
if...'
Loading cutlery and dishes
Helpful hints and tips
Caution! Only use the appliance for
household utensils that are applicable for
dishwashers.
Do not use the appliance to clean objects that
can absorb water (sponges, household cloths,
etc.).
Before you load cutlery and dishes, do these
steps:
Remove all food remainings and debris.
Make burnt, remaining food in pans soft.
While you load cutlery and dishes, do these
steps:
Load hollow items (e.g. cups, glasses and
pans) with the opening down.
Make sure that water does not collect in
the container or in a deep base.
Make sure that cutlery and dishes do not
lie inside one another.
Make sure that cutlery and dishes do not
cover other cutlery and dishes.
Make sure that glasses do not touch other
glasses.
Put small objects in the cutlery basket.
Plastic items and pans with non-stick coat-
ings can keep water droplets. Plastic items
do not dry as well as porcelain and steel
items.
Put light items in the upper basket. Make
sure that the items do not move.
Caution! Make sure that the spray arms
can move freely before you start a
washing programme.
Warning! Always close the door after
you load or unload the appliance. An
open door can be dangerous.
Arrange service
dishes and large lids
around the edge of
the lower basket.
Use the cutlery grid. If the dimensions of
the cutlery prevent use of the cutlery grid,
remove it.
ENGLISH 12
Arrange the items to let water touch all sur-
faces (left). For longer items fold the cup
racks up (right).
Put plates in the rear part of the upper
basket. Tilt them forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first
move the upper basket to a upper position.
Warning! Adjust the height before you
load the upper basket.
Maximum height of the dishes in :
Upper basket.
Upper position: 20 cm.
Lower position: 24 cm.
•Lower basket.
Upper position: 31 cm.
Lower position: 27 cm.
A
A
Do these steps to move the upper basket to the
upper or lower position:
1. Move the front runner stops (A) out.
2. Pull the basket out.
3. Put the basket in the upper or lower posi-
tion.
4. Replace the front runner stops (A) in their
initial position.
Caution! If the basket is in the upper
position, do not put cups on the cup racks.
Use of detergent
Only use detergents (powder, liquid or
tablet) that are applicable for dishwash-
ers.
Follow the data on the packaging:
Dosage recommended by the manufactur-
er.
Storage recommendations.
Do not use more than the correct quantity of
detergent to save an environment.
1 2
ENGLISH 13
3
A
Fill the detergent dis-
penser (A) with de-
tergent.
4
B
If you use a washing
programme with
prewash phase, put
more detergent in
the prewash deter-
gent compartment
(B).
5
A
6
Use of detergent tablets
Put the detergent tablet in the detergent dis-
penser (A).
Detergent tablets contain:
•detergent
•rinse aid
other cleaning agents.
Do these steps to use detergent tablets:
1. Make sure that the detergent tablets are
applicable for your water hardness. Refer
to the instructions from the manufacturer.
2. Set the lowest levels of water hardness and
rinse aid dosage.
It is not necessary to fill the salt container
and the rinse aid dispenser.
Do these steps when the drying results are
not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
Do these steps to use the detergent powder
again:
1. Fill the salt container and the rinse aid dis-
penser.
2. Set the water softener to the highest level.
3. Do a washing programme without dishes.
4. Adjust the water softener. Refer to the
chapter 'Setting the water softener'.
5. Adjust the rinse aid dosage.
Different brands of detergent dissolve in
different times. Some detergent tablets
do not have the best cleaning results during
short washing programmes. Use long washing
programmes when you use detergent tablets
to fully remove the detergent.
Setting and starting a washing programme
Set the washing programme with the
door ajar. The washing programme only
starts after you close the door. Until then it is
possible to modify the settings.
Do these steps to set and start a washing pro-
gramme:
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press the programme selection/cancel
button again and again to set the washing
programme. Refer to the chapter 'Washing
programmes'.
– The programme indicator light comes
on.
4. Close the door.
The washing programme starts auto-
matically.
When the washing programme operates,
you cannot change the programme. Can-
cel the washing programme.
ENGLISH 14
Warning! Only interrupt or cancel a
washing programme if necessary.
Caution! Open the door carefully. Hot
steam can come free.
Cancelling a washing programme
1. Press and hold the programme selection/
cancel button for approximately 3 seconds.
The programme indicator light goes off.
The end indicator light starts to flash.
2. Release the programme selection/cancel
button to cancel the washing programme.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with detergent be-
fore you set a new washing programme.
Interrupting a washing programme
Open the door.
The programme stops.
Close the door.
The programme continues from the point of
interruption.
End of the washing programme
Switch off the appliance in these conditions:
The appliance stops automatically.
The audible signals for the end of the pro-
gramme operate.
1. Open the door.
The end indicator light comes on.
The programme indicator light stays on.
2. Press the on/off button.
3. For better drying results, keep the door
ajar for some minutes before you remove
the dishes.
Let the dishes cool down before you remove
them from the appliance. Hot dishes are easily
damaged.
Removing the load
First remove items from the lower basket,
then from the upper basket.
There can be water on the sides and door
of the appliance. Stainless steel becomes
cool more quickly than the dishes.
Care and cleaning
Warning! Switch the appliance off before
you clean the filters.
Cleaning the filters
Important! Do not use the appliance without
the filters. Make sure that the installation of the
filters is correct. Incorrect installation will cause
unsatisfactory washing results and damage to
the appliance.
1 2
A
C
B
Fully clean the filters
A, B and C below run-
ning water.
ENGLISH 15
3
1
2
To remove filters B
and C, turn the han-
dle approximately
1/4 anticlockwise.
4
A
Remove the flat filter
A from the bottom of
the appliance.
5
A
D
Put the flat filter A in
the bottom of the ap-
pliance. Install the
flat filter correctly un-
der the two guides D.
6
2
1
Put the filter system in
position. To lock the
filter system, turn the
handle clockwise un-
til it locks in position.
Important! Do not remove the spray arms.
If the holes in the spray arms become clogged,
remove remaining parts of soil with a cocktail
stick.
Long periods of non-operation
Do these steps when you do not use the ap-
pliance for a long period:
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Keep the door open to prevent unpleasant
smells.
4. Keep the inner side of the appliance clean
(filters especially).
External cleaning
Clean the external surfaces of the appliance
and control panel with a damp soft cloth. Only
use neutral detergents. Do not use abrasive
products, scouring pads or solvents (acetone,
trichloroethylene etc...).
Frost precautions
Caution! Do not install the appliance
where the temperature is below 0 °C. The
manufacturer is not responsible for damage
because of frost.
If not possible, empty the appliance and close
the door. Disconnect the water inlet hose and
remove water from the water inlet hose.
ENGLISH 16
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution
to the problem yourself, contact your dealer or the After Sales Service.
Problem Possible cause Solution
Continuous flash
of the light of the
running pro-
gramme.
Intermittent audi-
ble signal.
1 flash of the end
indicator light.
Malfunction:
The dishwasher
does not fill with wa-
ter.
The water tap is blocked or furred
with limescale.
Clean the water tap.
The water tap is closed. Open the water tap.
The filter in the water inlet hose is
blocked.
Clean the filter.
The connection of the water inlet
hose is not correct. The hose can be
kinked or squashed.
Make sure that the connection is
correct.
Continuous flash
of the light of the
running pro-
gramme.
Intermittent audi-
ble signal.
2 flashes of the
end indicator
light.
Malfunction:
The dishwasher will
not drain.
There is a blockage in the sink spi-
got.
Clean the sink spigot.
The connection of the water drain
hose is not correct. The hose can be
kinked or squashed.
Make sure that the connection is
correct.
Continuous flash
of the light of the
running pro-
gramme.
Intermittent audi-
ble signal.
3 flashes of the
end indicator
light.
Malfunction:
The anti-flood de-
vice operates.
Close the water tap and Contact your local After Sales Service.
Malfunction:
The programme
does not start.
The appliance door is not closed. Close the door.
Mains plug is not connected in. Put in the mains.
ENGLISH 17
Problem Possible cause Solution
The fuse has blown out in the
household fuse box.
Replace the fuse.
After the check, switch on the appliance. The programme continues from the point of interrup-
tion. If the malfunction shows again, contact your After Sales Service.
When the cleaning results are not satisfactory:
Problem Possible cause Solution
The dishes are
not clean
The selected washing programme is
not applicable for the type of load
and soil.
Set different washing programme.
The baskets are loaded incorrectly so
that water cannot reach all surfaces.
Load the baskets correctly.
Spray arms do not turn freely because
of incorrect arrangement of the load.
Make sure that the cutlery and dishes
do not block the spray arms.
The filters are dirty or not correctly in-
stalled.
Make sure that the filters are clean
and installed correctly.
The quantity of detergent is too little
or missing.
Make sure that the quantity of deter-
gent in detergent dispenser is correct.
Limescales
particles on the
dishes
The salt container is empty. Fill the salt container with salt.
The water softener is adjusted on a
wrong level.
Set the water softener.
The salt container cap is not closed
correctly.
Make sure that the salt container is
closed correctly.
The dishes are
wet and dull
No rinse aid has been used. Set the rinse aid dosage.
The rinse aid dispenser is empty. Fill the rinse aid dispenser.
There are
streaks, milky
spots or a blu-
ish coating on
glasses and
dishes
Wrong dosage of rinse aid. Decrease the rinse aid dosage.
Dry water drop
signs on
glasses and
dishes
Wrong dosage of rinse aid. Increase rinse aid dosage.
The detergent can be the cause. Use different type of detergent.
Technical data
Dimensions Width (cm) 59,6
Height (cm) 81,8-87,8
ENGLISH 18
Depth (cm) 55,5
Water supply pressure
1)
Minimum
Maximum
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
Capacity (place settings) 12
Energy class A
Washing class A
Drying class A
Noise (dB(A)) 49
Average annual energy con-
sumption (kWh)
2)
231
Average annual water con-
sumption (litres)
2)
3520
1) If the pressure in your area is lower or higher, please contact your After Sales Service.
2) The data is based on the washing programme for test institutes assuming 220 cycles per a year.
Information on the electrical connection, voltage and overall power is given on the rating
plate on the inner edge of the dishwasher door.
Installation
Caution! Refer to the assembly
instructions, in order to proceed with the
installation.
Warning! Make sure that mains plug is
disconnected from the mains socket
during installation.
Place the appliance on the floor and install it
under a counter (kitchen worktop or sink).
If a repair is necessary, the appliance must be
easily accessible for the engineer.
Put the appliance adjacent to a water tap and
a drain.
For the venting of the dishwasher only water
fill, water drain and power supply cable open-
ings are necessary.
Water connection
This appliance has a special inlet hose for
water stop later defined as aqualock.
Water inlet hose
Connected the appliance to a hot (max. 60°)
or cold water supply.
If the hot water comes from alternative sources
of energy that are more environmentally
friendly (e.g. solar or photovoltaic panels and
aeolian), use a hot water supply to decrease
energy consumption.
Connect the inlet hose to a water tap with an
external thread of 3/4".
Caution! Do not use connection hoses
from an old appliance.
Caution! If you connect the appliance to
new pipes or pipes that are not used for
a long time, we recommend to run the water
for some minutes before you connect the inlet
hose.
ENGLISH 19
Aqualock inlet hose
The inlet hose is a high pressure resistant. It can
hold pressure at maximum 6 MPa. From ex-
ternal the inlet hose has a sheathing against
eventual damages. If the inner hose breaks,
the water that is in the hose will became dark.
You can see it across the special transparent
sheathing. Turn off the water tap immediately
and contact the After Sales Service.
A
B
The aqualock inlet
hose is installed with
a safety device to
prevent accidental
loosening. To discon-
nect the hose:
Press the lever ( B ).
Turn the retaining
ring ( A ) anticlock-
wise.
Turn the inlet hose to
the left or the right to
suit the installation.
Tight the locknut cor-
rectly to prevent wa-
ter leaks.
If you use a inlet
hose extension
the total reached
length must be no
longer than 4 metres.
Drain hose
A
If you connect the
water drain hose to a
water trap under the
sink, remove the
plastic membrane
(A). If you do not re-
move the membrane,
remaining food can
cause a blockage in
the drain hose spigot.
Caution! Make
sure that the
water couplings are
tight to prevent wa-
ter leakage.
Electrical connection
Warning! The manufacturer is not
responsible if you do not follow these
safety precautions.
Ground the appliance according to safety pre-
cautions.
Make sure that the rated voltage and type of
power on the rating plate agree with the volt-
age and the power of the local power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-way plugs, connectors and
extension cables. There is a risk of fire.
Do not replace the mains cable yourself. Con-
tact the After Sales Service.
Make sure that the mains plug is accessible
after installation.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
This appliance complies with the E.E.C. Direc-
tives.
ENGLISH 20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

IKEA DW60 Manuel utilisateur

Catégorie
Lave-vaisselle
Taper
Manuel utilisateur

dans d''autres langues