Indesit BHWD 125 GCC Le manuel du propriétaire

Marque: Indesit

Modèle: BHWD 125 GCC

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

English,1

! This symbol reminds you to read this

booklet.

Contents

Installation, 2-3-4-5-6-7

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Instructions for the fitter

Care and maintenance, 8

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Precautions and tips, 9

General safety

Disposal

Description of the washer-dryer and

starting a wash cycle, 10-11

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 12

Table of wash cycles

Personalisation, 13

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 14

Detergent dispenser drawer

Bleach cycle

Preparing the laundry

Garments requiring special care

Load balancing system

Troubleshooting, 15

Service, 16

BHWD 125

Instructions for use

WASHER DRYER

, 33

Français,17

Installation

! This instruction manual should be kept in a safe

place for future reference. If the washer dryer is

sold, transferred or moved, make sure that the

instruction manual remains with the machine so

that the new owner is able to familiarise himself/

herself with its operation and features.

! Read these instructions carefully: they contain

vital information relating to the safe installation

and operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer dryer from its packaging.

2. Make sure that the washer dryer has not been

damaged during the transportation process. If it

has been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4 pro-

tective screws (used

during transportation)

and the rubber washer

with the corresponding

spacer, located on the

rear part of the applian-

ce (see figure).

4. Close off the holes using the plastic plugs

provided.

5. Keep all the parts in a safe place: you will

need them again if the washer dryer needs to

be moved to another location.

! Packaging materials should not be used as

toys for children.

Levelling

1. Install the washer dryer on a flat sturdy floor,

without resting it up against walls, furniture ca-

binets or anything else.

2. If the floor is not per-

fectly level, compensa-

te for any unevenness

by tightening or loo-

sening the adjustable

front feet (see figure);

the angle of inclination,

measured in relation to

the worktop, must not

exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive

noise and prevent it from shifting while it is ope-

rating. If it is placed on carpet or a rug, adjust

the feet in such a way as to allow a sufficient

ventilation space underneath the washer dryer.

Connecting the electricity and wa-

ter supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to

a cold water tab using

a ¾ gas threaded con-

nection (see figure).

Before performing the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the inlet

hose to the washer dr-

yer by screwing it onto

the corresponding wa-

ter inlet of the applian-

ce, which is situated on

the top right-hand side

of the rear part of the

appliance (see figure).

3. Make sure that the hose is not folded over

or bent.

! The water pressure at the tap must fall within

the values indicated in the Technical details table

(see next page).

! If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

! Never use second-hand hoses.

! Use the ones supplied with the machine.

65 - 100 cm

Connecting the drain hose

Connect the drain

hose, without bending

it, to a drainage duct or

a wall drain located at a

height between 65 and

100 cm from the floor;

alternatively, rest it on

the side of a washba-

sin or bathtub, faste-

ning the duct supplied

to the tap (see figure).

The free end of the

hose should not be

underwater.

! We advise against the use of hose extensions;

if it is absolutely necessary, the extension must

have the same diameter as the original hose and

must not exceed 150 cm in length.

Electrical connections

Before plugging the appliance into the mains

socket, make sure that:

• the socket is earthed and in compliance with

the applicable law;

• the socket is able to sustain the appliance’s

maximum power load indicated on the Tech-

nical Data Plate fixed on the machine;

• the supply voltage is included within the values

indica- ted on the Technical Data Plate

fixed on the machine.

• the socket is compatible with the washing

machine’s plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fu-

sed plug it can be plugged into a 13 amp socket

for immediate use. Before using the appliance

please read the instructions below.

WARNING - THIS APPLIANCE MUST BE EAR-

THED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be

used, and the fuse cover re-fitted. If the fuse

cover is lost, the plug must not be used until a

replacement is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be

of the correct colour as indicated by the colou-

red marking or the colour that is embossed in

words on the base of the plug. Replacements

can be obtained directly from your nearest

Service Depot.

Removing the plug:

If your appliance has a non-rewireable moul-

ded plug and you should wish to re-route the

mains cable through partitions, units etc.,

please ensure that either:

the plug is replaced by a fused 13 ampere

rewireable plug bearing the BSI mark of ap-

proval.

or:

the mains cable is wired directly into a 13

amp cable outlet, controlled by a switch, (in

compliance with BS 5733) which is accessible

without moving the appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself,

you make the pins unusable so that it cannot

be accidentally inserted into a socket.

Instructions for connecting cable to an alternati-

ve plug:

Important: the wires in the mains lead are co-

loured in accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not

correspond with the coloured markings iden-

tifying the terminals in your plug, proceed as

follows:

Connect Green & Yellow wire to terminal

marked E or or coloured Green or Green &

Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or

coloured Black.

If a 13 amp plug (BS 1363) is used it must be

fitted with a

13 amp fuse, either in the plug or adaptor or

at the distribution board.

If you are in any doubt regarding the electrical

supply to your machine, consult a qualified

electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please re-

move the plug by cutting the mains cable as

close as possible to the plug body and dispo-

se of it as described on the previous page.

! The washing machine should not be installed

in an outdoor environment, not even where

the area is sheltered, because it may be very

dangerous to leave it exposed to damp, rain

and thunderstorms.

! When the washing machine is installed, the

mains socket must be within easy reach.

! Do not use extensions or multiple sockets.

! The power supply cable must never be bent

or dangerously compressed.

! The power supply cable must only be repla-

ced by an authorised serviceman.

Warning! The company denies all liability if and

when these norms are not respected.

The first wash cycle

Once the appliance has been installed, and

before you use it for the first time, run a wash

cycle with detergent and no laundry, using the

wash cycle 2.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Technical data

Model

BHWD 125

Dimensions

width 59,5 cm

height 81,5 cm

depth 54,5 cm

Capacity

from 1 to 7 kg for the wash

programme

from 1 to 5 kg for the drying

programme

Electrical

connections

please refer to the technical

data plate fixed to the ma-

chine

Water con-

nections

maximum pressure 1 MPa

(10 bar)

minimum pressure 0.05

MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per

minute

Energy ra-

ted

programmes

according to

regulation

EN 50229

Wash: programme 3; tem-

perature 60°C;

using a load of 7 kg.

Drying: Drying: the smaller

load must be dried by se-

lecting the

dryness level.

The load must consist of 2

sheets, 1 pillowcase and 1

hand towel;

the remainder of the load

must be dried by selecting

the dryness level.

This appliance conforms to

the following EC Directives:

- 2004/108/EC (Electromagne-

tic Compatibility)

- 2006/95/EC (Low Voltage)

- 2012/19/EU - WEEE

Tur seite

Instructions for the fitter

Mounting the wooden panel onto the door

and inserting the machine into cabinets:

In the case where the machine must be shipped

for final installation after the wooden panel has

been mounted, we suggest leaving it in its ori-

ginal packaging. The packaging was designed

to make it possible to mount the wooden panel

onto the machine without removing it completely

(see figures below).

The wooden panel that covers the face of

the machine must not be less than 18 mm in

thickness and can be hinged on either the right

or left. For the sake of practicality when using

the machine, we recommend that the panel be

hinged on the same side as the door for the

machine itself - the left.

Door Mounting Accessories (Fig. 1-2-3-4-5).

Fig. 1

N° 2 Hinges

N° 1 Magnet N° 1 Magnet plate

N° 1 Rubber plug

N° 2 Hinge Supports

N° 4 Spacers

Fig. 2

Fig. 3 Fig. 4

Fig. 5

Fig. 4/B

- No. 6 type A self-threading screws, l =13 mm.

- No. 2 type B metric, countersunk screws, l =25;

for fastening the magnet plate to the cabinet.

- No. 4 type C metric screws, l =15 mm; for

mounting the hinge supports to the cabinet.

- No. 4 type D metric screws, l =7 mm; for

mounting the hinges on the supports.

Mounting the Parts onto the Face of the

Machine.

- Fit the hinge supports to the appliance front

panel, positioning the hole marked with an arrow

in fig. 1 so that it is on the inner side of the front

panel. Fit a spacer (fig. 4/B) between the surfa-

ces using type C screws.

- Fit the magnet plate at the top of the opposite

side, using type B screws to fix two spacers (fig.

4/B) between the plate and the surface.

Using the Drilling Template.

- To trace the positions of the holes on the left-

hand side of the panel, align the drilling template

to the top left side of the panel using the lines

traced on the extremities as a reference.

- To trace the positions of the holes on the right-

hand side of the panel, align the drilling template

to the top right side of the panel.

- Use an appropriately sized router to mill the holes

for the two hinges, the rubber plug and the magnet.

Mounding the Parts onto the Wooden Panel

(Door).

- Insert the hinges into the holes (the movable part of

the hinge must be positioned facing away from the

panel) and fasten them with the 4 type A screws.

- Insert the magnet into the top hole on the op-

posite side of the hinges and fasten it with the

two type B screws.

- Insert the rubber plug into the bottom hole.

The panel is now ready to be mounted onto the

machine.

Mounting the Panel into the machine.

Insert the nib of the hinge (indicated by the arrow

in fig. 2) into the hole for the hinge and push the

panel towards the front of the machine. Fasten

the two hinges with the type D screws.

Fastening the plinth guide.

If the machine is installed at the end of a set of

modular cabinets, mount either one or both of

the guides for the base molding (as shown in fig.

8). Adjust them for depth based on the position

of the base molding, and, if necessary, fasten

the base to the guides (fig. 9).

This is how to assemble the plinth guide (fig. 8):

Fasten angle P using screw R, insert plinth guide

Q into the special slot and once it is in the desired

position, lock it in place using angle P and screw R.

Inserting the machine into the Cabinet.

- Push the machine into the opening, aligning it

with the cabinets (fig. 6).

- Regulate the adjustable feet to raise the ma-

chine to the appropriate height.

- To adjust the position of the wooden panel in

both the vertical and horizontal directions, use

the C and D screws, as shown in fig. 7.

Important: close the lower part of the appliance

front by ensuring that the plinth rests against the floor.

Fig. 8 Fig. 9

Accessories provided for the height

adjustment.

The following can be found inside the polystyrene

lid (fig. 10): 2 crossbars (G), 1 strip (M)

the following can be found

inside the appliance drum:

4 additional feet (H),

4 screws (I),

4 screws (R),

4 nuts (L),

2 plinth guides (Q)

Adjusting the appliance height.

The height of the appliance can be adjusted (from

815 mm to 835 mm), by turning the 4 feet.

Should you require the appliance to be placed

higher than the above height, you need to use the

following accessories to raise it to up to 870 mm:

The two crossbars (G); the 4 feet (H); the 4 screws (I); the

4 nuts (L) then perform the following operations (fig. 11):

remove the 4 original feet, place a crossbar G at

the front of the appliance, fastening it in place

using screws I (screwing them in where the ori-

ginal feet were) then insert the new feet H.

Repeat the same operation at the back of the appliance.

Now adjust feet H to raise or lower the appliance

from 835 mm to 870 mm.

Once you have reached the desired height, lock

nuts L onto crossbar G.

To adjust the appliance to a height between 870

mm and 900 mm, you need to mount strip M,

adjusting feet H to the required height.

Insert the strip as follows:

loosen the three screws N situated at the front of

the Top cover of the appliance, insert strip M as

shown in fig. 12, then fasten screws N.

570

min

815

540

595

820 ÷ 900

600 min

Fig. 6 Fig. 7

Fig. 11 Fig. 12

Fig. 10

Care and maintenance

Cutting off the water and electri-

city supplies

• Turn off the water tap after every wash cycle.

This will limit wear on the hydraulic system

inside the washer dryer and help to prevent

leaks.

• Unplug the washer dryer when cleaning it

and during all maintenance work.

Cleaning the washer dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth

soaked in lukewarm soapy water. Do not use

solvents or abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pul-

ling it out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of

your appliance

• Always leave the porthole door ajar in order

to prevent unpleasant odours from forming.

Cleaning the pump

The washer dryer is fitted with a self-cleaning

pump which does not require any maintenan-

ce. Sometimes, small items (such as coins or

buttons) may fall into the pre-chamber which

protects the pump, situated in its bottom part.

! Make sure the wash cycle has finished and

unplug the appliance.

To access the pre-chamber:

1. unscrew the lid

by rotating it anti-

clockwise (see figu-

re): a little water may

trickle out. This is

perfectly normal;

2. clean the inside thoroughly;

3. screw the lid back on;

Checking the water inlet hose

Check the inlet hose at least once a year. If

there are any cracks, it should be replaced

immediately: during the wash cycles, water

pressure is very strong and a cracked hose

could easily split open.

! Never use second-hand hoses.

Precautions and tips

! This washer dryer was designed and constructed in ac-

cordance with international safety regulations. The following

information is provided for safety reasons and must therefore

be read carefully.

General safety

• This appliance was designed for domestic use only.

• This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabi-

lities or lack of experience and knowledge if

they have been given supervision or instruction

concerning use of the appliance in a safe way

and understand the hazards involved. Children

shall not play with the appliance. Cleaning and

user maintenance shall not be made by children

without supervision.

– Do not dry unwashed items in the tumble dryer.

– Items that have been soiled with substan-

ces such as cooking oil, acetone, alcohol,

petrol, kerosene, spot removers, turpentine,

waxes and wax removers should be washed

in hot water with an extra amount of deter-

gent before being dried in the tumble dryer.

– Items such as foam rubber (latex foam),

shower caps, waterproof textiles, rubber

backed articles and clothes or pillows fitted

with foam rubber pads should not be dried in

the tumble dryer.

– Fabric softeners, or similar products,

should be used as specified by the fabric

softener instructions.

– The final part of a tumble dryer cycle occurs

without heat (cool down cycle) to ensure that

the items are left at a temperature that ensures

that the items will not be damaged.

WARNING: Never stop a tumble dryer before

the end of the drying cycle unless all items

are quickly removed and spread out so that

the heat is dissipated.

• Do not touch the machine when barefoot or with wet or

damp hands or feet.

• Do not pull on the power supply cable when unplugging

the appliance from the electricity socket. Hold the plug

and pull.

• Do not open the detergent dispenser drawer while the

machine is in operation.

• Do not touch the drained water as it may reach extreme-

ly high temperatures.

• Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

• If the appliance breaks down, do not under any circum-

stances access the internal mechanisms in an attempt

to repair it yourself.

• Always keep children well away from the appliance while

it is operating.

• The door can become quite hot during the wash cycle.

• If the appliance has to be moved, work in a group of two

or three people and handle it with the utmost care. Never

try to do this alone, because the appliance is very heavy.

• Before loading laundry into the washer-dryer, make sure

the drum is empty.

• During the drying phase, the door tends to get quite hot.

• Do not use the appliance to dry clothes that

have been washed with flammable solvents

(e.g. trichlorethylene).

• Do not use the appliance to dry foam rubber

or similar elastomers.

• Make sure that the water tap is turned on during

the drying cycles.

• Children of less than 3 years should be kept

away from the appliance unless continuou-

sly supervised.

• Remove all objects from pockets such as

lighters and matches.

Disposal

• Disposing of the packaging materials: observe local regu-

lations so that the packaging may be re-used.

• The European Directive 2012/19/EU - WEEE on Waste

Electrical and Electronic Equipment, requires that old hou-

sehold electrical appliances must not be disposed of in the

normal unsorted municipal waste stream. Old appliances

must be collected separately in order to optimise the recovery

and recycling of the materials they contain and reduce the

impact on human health and the environment. The crossed

out “wheeled bin” symbol on the product reminds you of

your obligation, that when you dispose of the appliance it

must be separately collected. Consumers should contact

their local authority or retailer for information concerning the

correct disposal of their old appliance.

Detergent dispenser drawer: used to dispense

detergents and washing additives (see “Detergents and

laundry”).

ON/OFF button: switches the washer-dryer on and off.

WASH CYCLE knob: programmes the wash cycles. Du-

ring the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to select the

available functions. The indicator light corresponding to the

selected function will remain lit.

TEMPERATURE knob: sets the temperature or the cold

wash cycle (see “Personalisation”).

DRYING knob: used to set the desired drying programme

(see “Personalisation”).

WASH CYCLE PROGRESS/DELAY TIMER

indicator

light

s: used to monitor the progress of the wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time remai-

ning until the wash cycle starts will be indicated (see next

page).

DOOR LOCKED indicator light: indicates whether the

door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or tem-

porarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash orange,

while the indicator light for the current wash cycle phase

will remain lit in a fixed manner. If the DOOR LOCKED

indicator light is switched off, the door may be opened

(wait approximately 3 minutes).

To start the wash cycle from the point at which it was inter-

rupted, press this button again.

Standby mode

This washing machine, in compliance with new energy sa-

ving regulations, is fitted with an automatic standby system

which is enabled after about 30 minutes if no activity is

detected. Press the ON-OFF button briefly and wait for the

machine to start up again.

Consumption in off-mode: 0,5 W

Consumption in Left-on: 8 W

Description of the washer-dryer

and starting a wash cycle

TEMPERATURE

knob

Detergent dispenser drawer

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

FUNCTION

buttons with

indicator lights

ON/OFF

button

DRYING

knob

DOOR

LOCKED

indicator light

START/PAUSE

button with indicator

light

Control panel

WASH CYCLE

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see “Per-

sonalisation”), after the wash cycle has been started the

indicator light corresponding to the selected delay period

will begin to flash:

As time passes, the remaining delay will be displayed and

the corresponding indicator light will flash:

Once the set delay has elapsed, the flashing indicator light

will switch off and the selected wash cycle will begin.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has be-

gun, the indicator lights switch on one by one to indicate which

phase of the cycle is currently in progress.

Note: during the “Drain” phase, the indicator light corre-

sponding to the “Spin” cycle phase will illuminate.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding indicator

light will illuminate.

If the selected function is not compatible with the program-

med wash cycle, the corresponding indicator light will flash

and the function will not be activated.

If a function which is incompatible with another function

selected previously, only the most recent selection will

remain active.

Door locked indicator light

If this indicator light is on, the appliance door is locked to

prevent it from being opened accidentally; to avoid any

damage, wait for the indicator light to switch off before you

open the appliance door (wait approximately 3 minutes).

N.B. If the DELAY TIMER function is activated, the door

cannot be opened; pause the machine by pressing the

START/PAUSE button if you wish to open it.

! If the START/PAUSE indicator light (orange) flashes

rapidly at the same time as the function indicator light, this

indicates a problem has occurred (see “Troubleshooting”).

Starting a wash cycle

1. Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then

only the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will

flash.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see “Personalisation”).

5. Set the drying cycle if necessary (see “Personalisation”).

6. Measure out the detergent and washing additives (see “Detergents and laundry”).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed

manner, in green. To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new

cycle.

9. At the end of the wash cycle the

indicator light will switch on. The DOOR LOCKED indicator light will switch off, indi-

cating that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries

completely (wait approximately 3 minutes). Switch the washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin

Dry

End of wash cycle

DOOR

LOCKED

indicator light

Note: as soon as a drying level

or time period has been set,

this indicator light illuminates

to indicate that the selected

wash cycle will be followed by a

drying phase.

Specials wash cycles

Mix 15’(wash cycle 8) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and

therefore saves both energy and time. By selecting this wash cycle (8 at 30°C), it is possible to wash different fabrics together

(except for wool and silk items), with a maximum load of 1.5 kg.

Daily 30’(wash cycle 9) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and

therefore saves both energy and time. By selecting this wash cycle (9 at 30°C), it is possible to wash different fabrics together

(except for wool and silk items), with a maximum load of 3 kg.

Wash cycles

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 3 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.

Table of wash cycles

Wash cycles

Description of the wash cycle

Max.

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max.

load

(kg)

Cycle

dura-

tion

Prewash Bleach Wash

Fabric

softener

Essentials

Cotton Prewash: extremely soiled whites. 90° 1200

 

7 170’

Cotton: Heavily soiled whites and resistant colours. 60° 1200



  

7 140’

Eco Cotton 60° (1): heavily soiled whites and resistant colours. 60° 1200



- -

 

7 180’

Eco Cotton 40° (2): lightly soiled whites and delicate colours. 40° 1200



- -

 

7 170’

Coloureds: Lightly soiled whites and delicate colours. 40° 1200



  

7 90’

Synthetics: lightly soiled resistant colours.

40°

(Max 60°)

1000



  

3 100’

Specials

6 Delicates

30° 0



- -

 

1 80’

Wool: For wool, cashmere, etc. 40° 800



- -

 

1,5 70’

Mix 15': To refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand).

30° 800 - - -

 

1,5 15’

Daily 30':To refresh lightly soiled garments quickly (not suitable

for wool, silk and clothes which require washing by hand).

30° 800 - - -

 

3 30’

10 Wash&Dry 45’

30° 1200



- -

 

1 45’

Drying

Drying Cottons - -



- - - - 5 -

Drying Synthetics - -



- - - - 3 -

Drying Wool - -



- - - - 1,5 -

Partials wash cycles

Rinse - 1200



- - -



7 36’

Spin - 1200



- - - - 7 10’

Pump Out - 0 - - - - - 7 3’

The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-

ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash (

The washer-dryer will automatically prevent you from selecting a temperature which is higher than the maximum value set for

each wash cycle.

! Exception: if the 5 programme is selected, the temperature can be increased up to a value of 60°C.

Setting the drying cycle

Turn the DRYING knob to set the desired drying type.

Two options are available:

A - Based on time: from 40 to 180 minutes.

B - Based on the how damp the clothes are once they have

been dried:

Iron

: slightly damp clothes, easy to iron.

Hanger : dry clothes to put away.

Cupboard : very dry clothes, recommended for towelling

and bathrobes.

If your laundry load to be washed and dried is much greater

than the maximum stated load (see adjacent table), perform

the wash cycle, and when the cycle is complete, divide the

garments into groups and put some of them back in the

drum. At this point, follow the instructions provided for a “Drying only” cycle. Repeat this procedure for the remainder of the

load.

N.B: When the drying is complete there is a cooling period, even though the DRYING knob is in the

position.

Drying only

Turn the WASH CYCLE knob to one of the drying settings (11-12-13) according to the type of fabric, then select the desired

drying duration using the DRYING knob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note:

- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and

the function will not be activated.

- If a function which is incompatible with another function selected previously, only the most recent selection will remain active.

1/2 Spin

By selecting this function, reduces the spin speed.

Super Wash

Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this

function offers a high-performance wash.

Extra rinse

By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly

useful for sensitive skin.

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours.

Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button

is pressed, the function will be disabled.

N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.

Personalisation

Table of Drying times (guideline values)

Fabric

type

Load type

Max.

load

(kg)

Cupboard

dry

Henger

dry

Iron

dry

Cotton

Clothing of different

sizes, Terry towels

5 250 210 190

Syn-

thetics

Sheets, Shirts, Py-

jamas, socks, etc.

3 180 130 115

Wool

Knitwear, Pullovers,

etc.

1,5 150 140 130

Detergents and laundry

Preparing the laundry

• Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from whites.

• Empty all garment pockets and check the buttons.

• Do not exceed the listed values, which refer to the

weight of the laundry when dry: see “Table of wash

cycles”.

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Delicates: use programme 6 to wash very delicate

garments. It is advisable to turn the garments inside out

before washing them. For best results, use liquid detergent

on delicate garments.

When selecting an exclusively time-based drying function, a

drying cycle is performed at the end of the wash cycle that is

particularly delicate, thanks to light handling and appropriate

temperature control of the water jet.

The recommended durations are:

1 kg of synthetic garments --> 150 min

1 kg of synthetic and cotton garments --> 180 min

1 kg of cotton garments --> 180 min

The degree of dryness depends on the load and fabric

composition.

Wool - Woolmark Apparel Care - Green:

the wool wash cycle of this machine has been approved

by The Woolmark Company for the washing of wool gar-

ments labelled as “hand wash” provided that the products

are washed according to the instructions on the garment

label and those issued by the manufacturer of this washing

machine (M1126)

Wash&Dry 45’ select programme

for washing and drying

lightly soiled garments (Cotton and Synthetic) in a short time.

This cycle may be used to wash and dry a laundry load of

up to 1 kg in just 45 minutes. To achieve optimum results,

use liquid detergent and pre-treat cuffs, collars and stains.

Load balancing system

Before every spin cycle, to avoid excessive vibrations and

to distribute the load in a uniform manner, the drum rotates

continuously at a speed which is slightly greater than the

washing rotation speed. If, after several attempts, the load is

not balanced correctly, the machine spins at a reduced spin

speed. If the load is excessively unbalanced, the washer-

dryer performs the distribution process instead of spinning.

To encourage improved load distribution and balance, we

recommend small and large garments are mixed in the load.

Detergent dispenser drawer

Good washing results also depend on the correct dose of

detergent: adding too much detergent will not necessa-

rily result in a more efficient wash, and may in fact cause

build up on the inside of your appliance and contribute to

environmental pollution.

!Use powder detergent for white cotton garments, for pre-

washing, and for washing at temperatures over 60°C.

!Follow the instructions given on the detergent packaging.

! Do not use hand washing detergents because these

create too much foam.

Open the detergent di-

spenser drawer and pour

in the detergent or washing

additive, as follows.

compartment 1: Pre-wash detergent (powder)

Before pouring in the detergent, make sure that extra com-

partment 4 has been removed.

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

extra compartment 4: Bleach

Bleach cycle

! Traditional bleach should be used on sturdy white fa-

brics, and delicate bleach for coloured fabrics, synthetics

and for wool.

This option is particularly

useful for the removal of

stubborn stains. Place extra

compartment 4 (supplied)

into compartment 1.

When pouring in the bleach,

be careful not to exceed

the “max” level marked

on the central pivot (see

figure). To run the bleach

cycle on its own, pour the bleach into extra compartment

4, set the “Rinse” programme and activate the “Super

Wash”

option. To bleach during a wash cycle, pour in

the detergent and any fabric softener you wish to use, set

the desired wash cycle and enable the “Super Wash”

option. The use of extra compartment 4 excludes the “Pre-

wash” option.

MAX

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that

the problem cannot be not solved easily using the following list.

Problem:

The washer-dryer does not switch

on.

The wash cycle does not start.

The washer-dryer does not take

in water (the indicator light for

the first wash cycle stage flashes

rapidly).

The washer-dryer continuously

takes in and drains water.

The washer-dryer does not drain or

spin.

The washer-dryer vibrates a lot

during the spin cycle.

The washer-dryer leaks.

The START/PAUSE indicator light

(orange) and the function indicator

lights flash rapidly.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

• The appliance is not plugged into the socket fully, or is not making contact.

• There is no power in the house.

• The washer-dryer door is not closed properly.

• The ON/OFF button has not been pressed.

• The START/PAUSE button has not been pressed.

• The water tap has not been opened.

• A delayed start has been set (see “Personalisation”).

• The water inlet hose is not connected to the tap.

• The hose is bent.

• The water tap has not been opened.

• There is no water supply in the house.

• The pressure is too low.

• The START/PAUSE button has not been pressed.

• The drain hose is not fitted at a height between 65 and 100 cm from the floor

(see “Installation”).

• The free end of the hose is under water (see “Installation”).

• The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to avoid this inconvenience.

• The wash cycle does not include draining: some wash cycles require the drain

phase to be started manually.

• The drain hose is bent (see “Installation”).

• The drainage duct is clogged.

• The drum was not unlocked correctly during installation (see “Installation”).

• The washer-dryer is not level (see “Installation”).

• The washer-dryer is trapped between cabinets and walls (see “Installation”).

• The water inlet hose is not screwed on properly (see “Installation”).

• The detergent dispenser drawer is blocked (for cleaning instructions, see “Care

and maintenance”).

• The drain hose is not fixed properly (see “Installation”).

• Switch off the machine and unplug it, wait for approximately 1 minute and then

switch it back on again.

If the problem persists, contact the Technical Assistance Service.

• The detergent is not suitable for machine washing (it should display the text

“for washer-dryers” or “hand and machine wash”, or the like).

• Too much detergent was used.

• The appliance is not plugged into the socket, or not enough to make contact.

• There has been a power failure.

• The appliance door is not shut properly.

• A delayed start has been set.

• The DRYING knob is on the setting.

Service

Before calling for Assistance:

• Check whether you can solve the problem alone (see “Troubleshooting”);

• Restart the programme to check whether the problem has been solved;

• If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the

guarantee certificate.

! Always request the assistance of authorised technicians.

Have the following information to hand:

• the type of problem;

• the appliance model (Mod.);

• the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be found on the front of

the appliance by opening the door.

Français

! Ce symbole vous rappelle de lire ce mode

d’emploi

Sommaire

Installation, 18-19-20-21-22-23

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Instructions pour l’installateur

Entretien et soin, 24

Coupure de l’arrivée d’eau et du courant

Nettoyage du lavante-séchante

Nettoyage du tiroir à produits lessiviels.

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau d’arrivée de l’eau

Précautions et conseils, 25

Sécurité générale

Mise au rebut

Description du lavante-séchante et dé-

marrage d’un programme, 26-27

Bandeau de commandes

Voyants

Démarrage d’un programme

Programmes, 28

Tableau des programmes

Personnalisations, 29

Sélection de la température

Sélectionner le séchage

Fonctions

Produits lessiviels et linge, 30

Tiroir à produits lessiviels

Cycle blanchissage

Triage du linge

Linge ou vêtements particuliers

Système d’équilibrage de la charge

Anomalies et remèdes, 31

Assistance, 32

BHWD 125

Mode d’emploi

LAVANTE-SÉCHANTE

Installation

! Conserver ce mode d’emploi pour pouvoir le con-

sulter à tout moment. En cas de vente, de cession ou

de déménagement, veiller à ce qu’il suive toujours le

lavante-séchante pour que son nouveau propriétaire

soit informé sur son mode de fonctionnement et

puisse profiter des conseils correspondants.

! Lire attentivement les instructions: elles fournis-

sent des conseils importants sur l’installation,

l’utilisation et la sécurité de l’appareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante n’a pas été

endommagé pendant le transport. S’il est abîmé,

ne pas le raccorder et contacter le vendeur.

3. Enlever les 4 vis

de protection servant

au transport, le ca-

outchouc et la cale,

placés dans la partie

arrière (voir figure).

4. Boucher les trous à l’aide des bouchons

plastique fournis.

5. Conserver toutes ces pièces: il faudra les re-

monter en cas de transport du lavante-séchante.

! Les pièces d’emballage ne sont pas des jouets

pour enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat

et rigide, sans l’appuyer contre des murs, des

meubles ou autre.

2. Si le sol n’est pas

parfaitement horizon-

tal, visser ou dévisser

les pieds de réglage

avant (voir figure) pour

niveler l’appareil; son

angle d’inclinaison,

mesuré sur le plan

de travail, ne doit pas

dépasser 2°.

Une bonne mise à niveau garantit la stabilité

de l’appareil et évite qu’il y ait des vibrations,

du bruit et des déplacements en cours de

fonctionnement. Si la machine est posée sur

de la moquette ou un tapis, régler les pieds de

manière à ce qu’il y ait suffisamment d’espace

pour assurer une bonne ventilation.

Raccordements eau et électricité

Raccordement du tuyau d’arrivée de l’eau

1. Reliez le tuyau d’ali-

mentation en le vissant

à un robinet d’eau froi-

de à embout fileté 3/4

gaz (voir figure).

Faire couler l’eau ju-

squ’à ce qu’elle soit

limpide et sans impure-

tés avant de raccorder.

2. Raccorder le tuyau

d’arrivée de l’eau au

lavante-séchante en le

vissant à la prise d’eau

prévue, dans la partie

arrière en haut à droite

(voir figure).

3. Attention à ce que le tuyau ne soit pas plié

ou écrasé.

! La pression de l’eau doit être comprise entre

les valeurs indiquées dans le tableau des Ca-

ractéristiques techniques (voir page ci-contre).

! Si la longueur du tuyau d’alimentation ne suffit

pas, s’adresser à un magasin spécialisé ou à un

technicien agréé.

! N’utiliser que des tuyaux neufs.

! Utiliser ceux qui sont fournis avec l’appareil.

65 - 100 cm

Raccordement du tuyau de vidange

Raccorder le tuyau

d’évacuation, sans

le plier, à un conduit

d’évacuation ou à une

évacuation murale pla-

cés à une distance du

sol comprise entre 65

et 100 cm;

ou bien l’accrocher à

un évier ou à une bai-

gnoire, dans ce cas,

fixer le support en pla-

stique fourni avec l’ap-

pareil au robinet (voir

figure). L’extrémité libre

du tuyau d’évacuation

ne doit pas être plon-

gée dans l’eau.

! L’utilisation d’un tuyau de rallonge est absolument

déconseillée mais si on ne peut faire autrement, il faut

absolument qu’il ait le même diamètre que le tuyau

original et sa longueur ne doit pas dépasser 150 cm.

Branchement électrique

Avant de brancher votre électroménager à la

prise de courant, contrôlez que:

• la prise est bien avec terre et conforme aux

réglementations applicables en la matière;

• la prise électrique est bien apte à supporter la

puissance maximum de l’électroménager figurant

sur la plaquette des caractéristiques;

• la tension d’alimentation est bien comprise

entre les valeurs figurant sur la plaquette des

caractéristiques;

• la prise est bien compatible avec la fiche du

lave-linge. Autrement, remplacez la prise ou la

fiche.

Votre électroménager dispose à présent d’une

fiche moulée 13 ampères qui peut être branchée

dans une prise compatible pour utilisation im-

médiate. Veuillez lire les instructions suivantes

avant d’utiliser votre électroménager.

ATTENTION - L’ELECTROMENAGER DOIT

ETRE RACCORDE A LA MASSE. LES OPERA-

TIONS DECRITES CI-APRES DOIVENT ETRE

EFFECTUEES PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible:

En cas de remplacement d’un fusible défec-

tueux, utilisez toujours des fusibles de 13 am-

pères ASTA conformes au standard BS1362 et

remontez le couvercle du fusible. Si vous avez

perdu le couvercle du fusible, n’utilisez pas la

fiche tant que la pièce manquante n’aura pas

été remplacée.

Couvercles des fusibles:

Si vous remplacez le couvercle du fusible, veil-

lez à ce que sa couleur soit bien celle qui est

indiquée par le code ou l’indication colorée à

la base de la fiche. Pour toute pièce détachée,

adressez-vous directement au centre d’assi-

stance technique le plus proche de chez vous.

Démontage de la fiche:

Si l’électroménager est équipé d’une fiche in-

corporée qui ne peut pas être câblée à nouveau

et s’il faut faire passer le câble à travers des

divisions, des unités, etc. contrôlez que:

la fiche est bien remplacée par une autre câbla-

ble à nouveau de 13 ampères portant la marque

BSI

ou bien:

que le câble est bien raccordé directement à la

prise de 13 ampères, contrôlée par un interrup-

teur (conforme BS 5733) accessible sans qu’il

faille déplacer l’électroménager.

Elimination de la fiche:

Avant d’éliminer la fiche, rendez les broches inu-

tilisables de manière à ce que la fiche ne puisse

pas être branchée accidentellement dans une

prise.

Instructions pour le raccordement du câble à

une fiche alternative:

Important: les couleurs des fils du câble de ré-

seau correspondent à la codification suivante:

Jaune/Vert Terre

Bleu Neutre

Marron Alimenté

Les couleurs des fils du câble pourraient ne

pas correspondre aux indications de couleur

qui identifient les broches de la fiche, procédez

comme suit:

raccordez le fil jaune/vert à la borne repérée par

la lettre E ou ou de couleur verte ou jaune/vert

raccordez le fil marron à la borne repérée par la

lettre L ou de couleur rouge

raccordez le fil bleu à la borne repérée par la

lettre N ou de couleur noire.

En cas d’utilisation d’une fiche de 13 ampères

(BS 1363), installez un fusible de 13 ampères

dans la fiche ou sur l’adaptateur ou sur la carte

de distribution.

En cas de doute sur l’alimentation électrique de

votre électroménager, faites appel à un électri-

cien qualifié avant de le mettre en service.

Raccordement d’une fiche alternative:

les couleurs des fils du câble de réseau corre-

spondent à la codification suivante:

BLEU NEUTRE (N)

MARRON ALIMENTE (L)

JAUNE/VERT TERRE (E)

Elimination de l’électroménager:

Lors de la mise au rebus de l’électroménager,

débarrassez-le de sa fiche en coupant le câble

d’alimentation le plus près possible de cette der-

nière et éliminez comme décrit précédemment.

! Votre lave-linge ne doit pas être installé dehors,

même à l’abri, car il est très dangereux de le

laisser exposé à la pluie et aux orages.

! Après installation du lave-linge, la prise de

courant doit être facilement accessible.

! N’utilisez ni rallonges ni prises multiples.

! Le câble ne doit être ni plié ni écrasé.

! Le câble d’alimentation ne doit être remplacé

que par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non respect des normes énumérées ci-dessus.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Premier cycle de lavage

Avant la première mise en service de l’appareil, ef-

fectuer un cycle de lavage avec un produit lessiviel

mais sans linge et sélectionner le programme 2.

La page charge ...

Indesit BHWD 125 GCC Le manuel du propriétaire

Marque: Indesit

Modèle: BHWD 125 GCC

Catégorie: Machines à laver

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit BHWD 125 GCC Owner's manual

Indesit BHWD 125 GCC Le manuel du propriétaire

Indesit BHWD 125 GCC Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents