Snom M10 KLE Quick Installation Guide

Catégorie
Téléphones
Taper
Quick Installation Guide
M10 KLE
SIP DECT 4-Line Handset
Quick Installa� on Guide
Taihoon Kim | 24. Jan. 2019 | Revision 1.0AW | M10-Handset (US version)
illustration scale 100%
Silkscreen on the Rear
Pantone 8001C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Top
Pantone 200C
Silkscreen on the Rear
Transluscent
Pantone Cool Gray 3C
2
Important Safety Information
This symbol is to alert you to important operating or servicing
instructions that may appear on the product or in this user’s manual.
Always follow basic safety precautions when using this product to
reduce the risk of injury, re, or electric shock.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always be
followed to reduce the risk of re, electric shock and injury, including the following:
1. This product should be installed by a qualied technician.
2. This product should only be connected to the host equipment and never
directly to the network such as Public Switch Telephone Network (PSTN) or
Plain Old Telephone Services (POTS).
3. Read and understand all instructions.
4. Follow all warnings and instructions marked on the product.
5. Unplug this product from the wall outlet before cleaning. Do not use liquid or
aerosol cleaners. Use a damp cloth for cleaning.
6. Do not use this product near water such as near a bath tub, wash bowl,
kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.
7. Do not place this product on an unstable table, shelf, stand or other unstable
surfaces.
8. Slots and openings in the back or bottom of the handset are provided for
ventilation. To protect them from overheating, these openings must not be
blocked by placing the product on a soft surface such as a bed, sofa or rug.
This product should never be placed near or over a radiator or heat register.
This product should not be placed in any area where proper ventilation is not
provided.
9. This product should be operated only from the type of power source indicated
on the marking label. If you are not sure of the type of power supplied at the
premises, consult your dealer or local power company.
10. Do not allow anything to rest on the power cord. Do not install this product
where the cord may be walked on.
11. Never push objects of any kind into this product through the slots in the
handset because they may touch dangerous voltage points or create a short
circuit. Never spill liquid of any kind on the product.
12. To reduce the risk of electric shock, do not disassemble this product, but take
it to an authorized service facility. Opening or removing parts of the handset
other than specied access doors may expose you to dangerous voltages or
other risks. Incorrect reassembling can cause electric shock when the product
is subsequently used.
3
13. Do not overload wall outlets and extension cords.
14. Unplug this product from the wall outlet and refer servicing to an authorized
service facility under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled onto the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operation instructions. Improper adjustment of other controls may
result in damage and often requires extensive work by an authorized
technician to restore the product to normal operation.
E. If the product has been dropped and the telephone base and/or
handset has been damaged.
F. If the product exhibits a distinct change in performance.
15. Avoid using a telephone (other than cordless) during an electrical storm.
There is a remote risk of electric shock from lightning.
16. Do not use the telephone to report a gas leak in the vicinity of the leak. Under
certain circumstances, a spark may be created when the adapter is plugged
into the power outlet, or when the handset is replaced in its cradle. This is a
common event associated with the closing of any electrical circuit. The user
should not plug the phone into a power outlet, and should not put a charged
handset into the cradle, if the phone is located in an environment containing
concentrations of ammable or ame-supporting gases, unless there is
adequate ventilation. A spark in such an environment could create a re or
explosion. Such environments might include: medical use of oxygen without
adequate ventilation; industrial gases (cleaning solvents; gasoline vapors;
etc.); a leak of natural gas; etc.
17. Only put the handset of your telephone next to your ear when it is in normal
talk mode.
18. The power adapters are intended to be correctly oriented in a vertical or oor
mount position. The prongs are not designed to hold the plug in place if it is
plugged into a ceiling, under-the-table or cabinet outlet.
19. Use only the power cord indicated in this manual.
20. For pluggable equipment, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
21. In wall mounting position, make sure to mount the telephone base on the wall
by aligning the eyelets with the mounting studs of the wall plate. Then slide
the telephone base down on both mounting studs until it locks into place.
Refer to the full installation instructions in the User Manual.
4
22. CAUTION: Keep small metallic objects such as pins and staples away from
the handset receiver.
SAVE THESE INSTRUCTIONS
For cUL compliance only
Mesures de sécurité importantes
Ce symbole vous alertera d’informations importantes ou d’instructions
d’entretien pouvant apparaître dans ce guide d’utilisation. Respectez
toujours les mesures de sécurité et de sécurité de base lorsque vous
utilisez ce produit, an de réduire les risques de blessures, d’incendie,
ou d’électrocution.
Mesures de sécurité importantes
An de réduire les risques d’incendie, de blessures corporelles ou d’électrocution,
suivez toujours ces mesures préventives de base lorsque vous utilisez votre
téléphone
1. Cet appareil doit être installé par un technicien qualié.
2. Cet appareil doit être branché à un équipement hôte et jamais branché à un
réseau, tel qu’un réseau PSTN publique ou un réseau téléphonique standard
(POTS).
3. Lisez et comprenez bien toutes les instructions.
4. Observez toutes les instructions et mises en garde inscrites sur l’appareil.
5. Débranchez ce téléphone de la prise murale avant de le nettoyer. N’utilisez
pas de nettoyeurs liquides ni en aérosol. N’utilisez qu’un chiffon doux et
légèrement humecté.
6. N’utilisez pas ce produit près de l’eau, tel que près d’un bain, d’un lavabo,
d’un évier de cuisine, d’un bac de lavage ou d’une piscine, ou dans un sous-
sol humide ou sous la douche.
7. Ne déposez pas ce téléphone sur un chariot, support ou table chancelants.
L’appareil pourrait tomber et être sérieusement endommagé.
8. Le boîtier de l’appareil est doté de fentes et d’ouvertures d’aération situées
à l’arrière ou en dessous. An d’empêcher la surchauffe, ces ouvertures ne
doivent pas être obstruées en plaçant l’appareil sur un lit, divan, tapis ou
autre surface similaires. Ne placez pas cet appareil à proximité d’un élément
de chauffage ni d’une plinthe électrique. De plus, ne l’installez pas dans une
unité murale ou un cabinet fermé qui ne possède pas d’aération adéquate.
9. Ne faites fonctionner cet appareil qu’avec le type d’alimentation indiqué sur
les étiquettes de l’appareil. Si vous ne connaissez pas le voltage de votre
5
maison, consultez votre marchand ou votre fournisseur d’électricité.
10. Ne déposez rien sur le cordon d’alimentation. Installez cet appareil dans
un endroit sécuritaire, là où personne ne pourra trébucher sur la ligne
d’alimentation ni le cordon téléphonique modulaire.
11. N’insérez jamais d’objets à travers les fentes et ouvertures de cet appareil,
car ils pourraient toucher à des points de tension dangereux ou court-circuiter
des pièces, ce qui constituerait un risque d’incendie ou d’électrocution.
N’échappez pas de liquides dans l’appareil.
12. An de réduire les risques d’électrocution, ne démontez pas l’appareil, mais
apportez-le plutôt à un centre de service qualié s’il doit être réparé. En
enlevant le couvercle, vous vous exposez à des tensions dangereuses ou
autres dangers similaires. Un remontage inadéquat peut être à l’origine d’une
électrocution lors d’une utilisation ultérieure de l’appareil.
13. Ne surchargez pas les prises de courant ni les rallonges électriques, car ceci
peut constituer un risque d’incendie ou d’électrocution.
14. Débranchez cet appareil de la prise de courant et communiquez avec le
département de service à la clientèle de Snom dans les cas suivants:
A. Lorsque le cordon d’alimentation est endommagé ou écorché.
B. Si du liquide a été échappé dans l’appareil.
C. Si l’appareil a été exposé à une source d’humidité telle que la pluie ou
l’eau.
D. Si l’appareil ne fonctionne pas normalement en suivant les directives du
guide. N’ajustez que les commandes couvertes dans le guide d’utilisation,
car un mauvais réglage de celles-ci peut être à l’origine de dommages, ce
qui nécessiterait des réparations considérables pour remettre l’appareil à
son état de fonctionnement normal.
E. Si l’appareil a été échappé ou son boîtier, endommagé.
F. Si le produit afche une nette diminution de sa performance.
15. Évitez d’utiliser un téléphone (autre qu’un sans l) pendant un orage. Les
éclairs peuvent être à l’origine d’une électrocution.
16. N’utilisez pas le téléphone pour rapporter une fuite de gaz à proximité de
celle-ci. Sous certaines circonstances, une inteincelle pourrait survenir
lorsque l’adaptateur est branché à une prise de courant, ou lorsque le
combiné est déposé sur le combiné. Ceci est un événement commun associé
avec la fermeture d’un circuit électrique. L’utilisateur ne devrait pas brancher
le téléphone dans une prise de courant, et ne devrait pas déposer le combiné
chargé sur le socle, si le téléphone se trouve dans un environnement ou la
concentration de gaz inammables, sans ventilation adéquate. Une étincelle
dans ces endroits pourrait provoquer un incendie ou une explosion. Ces
environnements pourraient être l’utilisation médicale de l’oxygène sans
6
ventilation adéquate; le gaz industriel (dissolvants, vapeurs d’essence, etc.);
une fuite de gaz naturel, etc.
17. Placez uniquement le combiné de votre appareil près de votre oreille lorsqu’il
est en mode de conversation normal.
18. Les adaptateurs sont conçus pour être orientés en position verticale ou en
position horizontale sur le plancher.
19. N’utilisez que cordon d’alimentation et les piles indiquées dans ce guide
d’utilisation.
20. Pour les PRODUITS À BRANCHER À UNE PRISE DE COURANT, la prise
de courant doit être installée près du produit, an d’assurer une accessibilité
sécuritaire à la prise de courant.
21. En position de montage mural, assurez-vous de monter le socle du téléphone
sur le mur en alignant les oeillets avec les goujons de xation de la plaque
murale. Ensuite, faites glisser le socle vers le bas sur les deux goujons de
xation jusqu’à ce qu’il se verrouille en place. Reportez-vous aux instructions
complètes dans la section Installation dans ce guide d’utilisation.
22. MISE EN GARDE : Éloignez les petits objets métalliques tels que les broches
de l’écouteur du combiné.
CONSERVEZ CES INSTRUCTIONS
7
Compliance
FCC part 15
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at the
user’s expense.
Privacy of communications may not be ensured when using this phone.
Warning: Changes or modications to this equipment not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
Caution: To maintain the compliance with the FCC’s RF exposure guideline, place
the base unit at least 20 cm from nearby persons.
For body-worn operation, this handset has been tested and meets the FCC RF
exposure guidelines when used with the accessories supplied or designated for
this product. Use of other accessories may not ensure compliance with FCC RF
exposure guidelines.
Industry Canada
This Class A digital apparatus complies with Canadian requirements:
CAN ICES-3 (A)/NMB-3(A). Cet appareil numérique de la classe A est conforme à la
norme CAN ICES-3 (A)/NMB-3(A) du Canada.
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Privacy of communications may not be ensured when using this telephone.
The term ‘’IC:‘’ before the certication/registration number only signies that the
Industry Canada technical specications were met.
This product meets the applicable Innovation, Science and Economic Development
Canada technical specications.
8
Parts Checklist
Your telephone package contains the following items. Save your sales receipt and
original packaging in the event warranty service is necessary.
About this Guide
This quick installation guide provides a reference for the external features of the
M10 KLE SIP DECT 4-Line Handset and installation instructions.
The M10 KLE SIP DECT 4-Line Handset is for use with the M100 KLE SIP DECT
4-Line Base Station or a compatible SIP deskset. Please refer to the M10 KLE SIP
DECT 4-Line Handset User Manual for complete operation instructions with the
base station.
For customer service or product information, visit our website at
www.snomamericas.com .
Quick Installation
Guide
Handset charger
DC adapter
Handset charger
Handset battery and
battery compartment
cover
Quick start guide
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING:DO NOT BURN OR
PUNCTURE BATTERIES
MADE IN CHINA CR1733
M10 KLE
Taihoon Kim | 24. Jan. 2019 | Revision 1.0AW | M10 Charger (US version)
Silkscreen on the Top
Pantone 8001C
illustration scale 100%
Taihoon Kim | 24. Jan. 2019 | Revision 1.0AW | M10-Handset (US version)
illustration scale 100%
Silkscreen on the Rear
Pantone 8001C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Top
Pantone 200C
Silkscreen on the Rear
Transluscent
Pantone Cool Gray 3C
Handset
9
Taihoon Kim | 24. Jan. 2019 | Revision 1.0AW | M10-Handset (US version)
illustration scale 100%
Silkscreen on the Rear
Pantone 8001C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Top
Pantone 200C
Silkscreen on the Rear
Transluscent
Pantone Cool Gray 3C
Taihoon Kim | 24. Jan. 2019 | Revision 1.0AW | M10-Handset (US version)
illustration scale 100%
Silkscreen on the Rear
Pantone 8001C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Rear
Pantone Cool Gray 3C
Silkscreen on the Top
Pantone 200C
Silkscreen on the Rear
Transluscent
Pantone Cool Gray 3C
Quick Reference Guide
Cordless handset external features
HEADSET JACK
2.5 mm jack for
connecting a corded
headset.
MESSAGES LED
Flashes when a line has
a new voice message.
MENU/SELECT
Press to display the main
menu.
Press to select a menu item.
OFF/CANCEL
Press to end a call.
Press to cancel an operation
and leave a menu.
On back:
BELT CLIP
SPEAKER
HOLD
Press to put a call on hold.
CID q
While in menus, press q
to scroll down the menu.
Press to display the Call
history.
DIR p
While in menus, press p
to scroll up the menu.
Press to display the
Directory.
Dial pad and audio controls
DIAL PAD
MUTE/DELETE
During a call, press to prevent
your voice from being heard.
While entering numbers
or letters, press to delete
previous character.
HANDSET LOCK
Press and hold to lock
handset keys and prevent
accidental key presses.
SPEAKER
Press to use the handset
speakerphone.
REDIAL/PAUSE
Press to redial a number
or enter a pause when
programming a phone number.
SOFT KEYS
Perform the actions
indicated by the on-
screen labels.
L1 - L4
Programmable
feature keys,
preprogrammed
as line keys for
accessing shared
calls.
– VOLUME +
During a call: increase or
decrease listening volume.
When idle: increase or
decrease ringer volume.
INT
Press to make an internal
(intercom) call to another
handset/deskset.
10
Handset Installation
This section assumes that your network infrastructure is established and that your
IP PBX phone service has been ordered and congured for your location.
Installation involves both the the handset and the handset charger. The handset
charger is powered using the supplied power adapter. The charger can be placed on a
at surface or mounted on a wall.
Avoid placing the handset and charger too close to:
Communication devices such as television sets, DVD players, or other cordless
telephones
Excessive heat sources
Noise sources such as a window with trafc outside, motors, microwave ovens,
refrigerators, or uorescent lighting
Excessive dust sources such as a workshop or garage
Excessive moisture
Extremely low temperature
Mechanical vibration or shock such as on top of a washing machine or work
bench
Installing the charger
Install the charger as shown below.
Plug the power adapter into an electrical outlet not controlled by a wall switch.
11
IMPORTANT INFORMATION
1. Use only the power adapter supplied with this product. To order a replacement
power adapter, visit our website at www.snomamericas.com .
2. The power adapter is intended to be correctly oriented in a vertical or oor mount
position. The prongs are not designed to hold the plug in place if it is plugged
into a ceiling, under-the-table or cabinet outlet.
Battery installation and charging
Install the battery as shown on the following page. Once you have installed the
battery, the screen indicates the battery status (see the table below). If necessary,
place the handset in the charger to charge the battery. For best performance, keep
the handset in the charger when not in use. The battery is fully charged after 11
hours of continuous charging.
If the screen is blank, you need to charge the handset without interruption for at least
30 minutes to give the handset enough charge to use the telephone for a short time.
When the battery is low, the handset shows Low battery and a ashing .
Battery indicators Battery Status Action
The screen is blank or
shows Place in charger
and ashes.
The battery has no or
little charge. The handset
cannot be used.
Charge without interruption
(at least 30 minutes).
The screen shows Low
battery and ashes.
Battery has enough
charge to be used for a
short time.
Charge without interruption
(at least 30 minutes).
Full battery icon ( )
appears.
Battery is charged. To keep the battery
charged, place it in the
charger when not in use.
12
To install the handset battery:
1. Plug the battery connector securely into the socket inside the handset battery
compartment. Insert the supplied battery with the label THIS SIDE UP facing up
as indicated.
2. Align the cover at against the battery compartment, then slide it upwards until it
clicks into place.
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING:DO NOT BURN OR
PUNCTURE BATTERIES
MADE IN CHINA CR1733
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING:DO NOT BURN OR
PUNCTURE BATTERIES
MADE IN CHINA CR1733
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING:DO NOT BURN OR
PUNCTURE BATTERIES
MADE IN CHINA CR1733
GP1250
3. Charge the handset by placing it face forward in the charger. The battery icon
indicates the charge status as the battery charges.
IMPORTANT INFORMATION
Use only the supplied rechargeable battery or replacement battery
(model BT264392). To order a replacement battery, visit our website at
www.snomamericas.com .
If you do not use the handset for a long time, disconnect and remove the battery
to prevent possible leakage.
Very low battery charging
less than 30 minutes.
Charging 30 to 80 minutes.
Charging 80 minutes
to 7 hours.
Charging more than 7 hours.
Fully charged at 11 hours.
13
Wall mounting the charger
The charger is ready for tabletop use. If you want to mount the charger on a wall,
use two 10 mm (3/8 inch) screws and wall anchors to hold the charger in place.
Screws and wall anchors are not provided, but are available for purchase at
hardware retailers. You might need a professional to install the charger.
To mount the charger on the wall:
1. Use a pencil to mark the desired positions of the two holes on the wall. Make
sure the space between the two holes is 30 mm (1 3/16 inches). Drill two holes
in the wall according to the marks.
2. If you drill the holes into a stud, go to step 3.
-OR-
If you drill the holes into an object other than a
stud, insert the wall anchors into the holes and tap
gently on the ends with a hammer until the wall
anchors are ush with the wall.
3. Insert the screws into the holes and tighten them
until only 6 mm (1/4 inch) of the screws are
exposed.
4. Align the holes at the back of the charger with the
screws on the wall and slide the charger down until
it locks into place.
Screw spacing 30 mm
(1 3/16 inches)
14
Adding a corded headset
You can use this handset hands-free when you install any industry-standard 2.5 mm
corded telephone headset (purchased separately).
Plug a 2.5 mm headset into
the HEADSET jack on the
side of the handset.
15
Handset Registration
Registering the handset to the base station
The handset must be registered to the base station in order to make and receive
calls.
To register the handset:
1. Make sure the handset has a charged battery before proceeding.
Make sure the base station is connected to power.
2. If the handset is displaying go to step 6.
3. If the handset is displaying go to step 7.
4. If the handset is displaying go to step 8.
5. If the handset is displaying go to step 7.
6. Press
CANCEL
.
The handset displays the following message:
16
7. Press
YES
.
The handset displays the following message:
8. On the base station, press the HANDSET LOCATOR button for at least four
seconds, then release the button. Both LEDs on the base station begin to ash.
9. Press the # key on the handset to begin registration.
The screen displays “Registering Please wait”.
The process takes up to 10 seconds to complete. When registration is complete,
the handset beeps and displays “Handset Registered”.
If the handset fails to register, place it in the charger again for a few seconds,
remove it and repeat the registration procedure.
Deregistering the handset
Before using the handset with a different base station, you must deregister the
handset from the base station to which it is currently registered.
To deregister the handset:
1. Press MENU on the handset. The Main Menu appears.
2. Press q to scroll to User settings and press SELECT.
3. Press q to scroll to Registration and press SELECT.
4. Press q to highlight Deregistration and press SELECT.
The handset screen displays a list of devices registered to the base station.
5. Press q to highlight the name of the handset you want to deregister, and then
press
SELECT
.
6. Enter the PIN, and then press SELECT to begin deregistration.
The default PIN is 1592.
Deregistration takes up to 10 seconds to complete. When the handset deregisters, it
beeps and the screen displays “Handset is deregistered.”
17
Note: The handset enters an energy-saving charging mode after being deregistered.
All cordless telephone functions except handset-battery charging are disabled.
Energy-saving charging mode is deactivated after the handset registers to the base
station.
Maintenance
Taking care of your telephone
Your base station and cordless handset contain sophisticated electronic parts,
so you must treat them with care.
Avoid rough treatment.
Place the handset down gently.
Save the original packing materials to protect your products if you ever need to
ship them.
Avoid water
You can damage your cordless telephone if it gets wet. Do not use the handset
in the rain, or handle it with wet hands. Do not install the base station and
handset near a sink, bathtub or shower.
Electrical storms
Electrical storms can sometimes cause power surges harmful to electronic
equipment. For your own safety, take caution when using electric appliances
during storms.
Cleaning your telephone
Your products have a durable plastic casing that should retain its luster for many
years. Clean it only with a soft cloth slightly dampened with water or a mild soap.
Do not use excess water or cleaning solvents of any kind.
Remember that electrical appliances can cause serious injury if used when you
are wet or standing in water. If the telephone base should fall into water, DO NOT
RETRIEVE IT UNTIL YOU UNPLUG THE POWER CORD FROM THE WALL, then
pull the unit out by the unplugged cord.
18
Technical Specications
RF frequency band 1921.536–1928.448 MHz
Channels 5
Operating temperature 32–104 °F (0–40 °C)
Power requirements Handset charger: 6.0Vdc 100mA
Handset: 2.4V 550mAh, Ni-MH battery pack
19
VTECH COMMUNICATIONS, INC.
Tigard, Oregon 97223, USA.
Copyright © 2019 Snom Technology GmbH. All Rights Reserved.
v2019002 Version 2, 06/19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20

Snom M10 KLE Quick Installation Guide

Catégorie
Téléphones
Taper
Quick Installation Guide

dans d''autres langues