Gaggenau VG425211CA Guide d'installation

Marque: Gaggenau

Modèle: VG425211CA

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

*DJJHQDX

Installation instructions 2

Notice de montage 18

Instrucciones de instalación 34

VG491211CA

Gas cooktop

Table de cuisson gaz

Encimera a gas

en-us

Table of Contents

Installation instructions

Safety Definitions 2

IMPORTANT SAFETY INSTRUCTIONS 3

Appliance Handling Safety 4

Safety Codes and Standards 4

Electric Safety 5

Gas Safety 5

Propane Gas Installation 6

Related Equipment Safety 6

Before You Begin 7

Tools and parts needed 7

Parts included 7

Special accessories 7

Cabinet Requirements 8

Countertop Requirements 8

Technical Data 8

Prepare Installation Space 9

Cutting out countertop 9

Installation Procedure 10

Mounting Control Knobs 10

Install Appliance 11

Connect Gas Supply 12

Connect Electrical Supply 12

Burner Cap Placement 12

Check the Installation 13

Removing the appliance 13

Conversion to another type of gas 14

Customer Service 17

Additional information on products, accessories,

replacement parts and services can be found at

www.gaggenau.com and in the online shop

www.gaggenau.com/zz/store

Safety Definitions

9 WARNING

This indicates that death or serious injuries may

occur as a result of non-observance of this

warning.

9 CAUTION

This indicates that minor or moderate injuries may

occur as a result of non-observance of this

warning.

NOTICE

This indicates that damage to the appliance or property

may occur as a result of non-compliance with this

advisory.

Note: This alerts you to important information and/or

tips.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

'RQRWVWRUHRUXVHJDVROLQHRURWKHUIODPPDEOH

YDSRUVDQGOLTXLGVLQWKHYLFLQLW\RIWKLVRUDQ\

RWKHUDSSOLDQFH

:+$772'2,)<2860(//*$6



'RQRWWU\WROLJKWDQ\DSSOLDQFH



'RQRWWRXFKDQ\HOHFWULFDOVZLWFK



'RQRWXVHDQ\SKRQHLQ\RXUEXLOGLQJ



,PPHGLDWHO\FDOO\RXUJDVVXSSOLHUIURPD

QHLJKERU·VSKRQH)ROORZWKHJDVVXSSOLHU·V

LQVWUXFWLRQV



,I\RXFDQQRWUHDFK\RXUJDVVXSSOLHUFDOO

WKHILUHGHSDUWPHQW

,QVWDOODWLRQDQGVHUYLFHPXVWEHSHUIRUPHG

E\DTXDOLILHGLQVWDOOHUVHUYLFHDJHQF\RUWKH

JDVVXSSOLHU



:$51,1*,IWKHLQIRUPDWLRQLQWKHVHLQVWUXFWLRQV

LVQRWIROORZHGH[DFWO\DILUHRUH[SORVLRQPD\

UHVXOWFDXVLQJSURSHUW\GDPDJHSHUVRQDOLQMXU\

RUGHDWK

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT: THE APPLIANCE HAS TO

BE INSTALLED BY A QUALIFIED

INSTALLER.

INSTALLER: LEAVE THESE

INSTRUCTIONS WITH THE APPLIANCE

AFTER INSTALLATION IS COMPLETE.

IMPORTANT: SAVE FOR THE LOCAL

INSPECTOR’S USE.

9 WARNING

If the information in this manual is

not followed exactly, fire or shock

may result causing property damage

or personal injury.

9 WARNING

Do not repair, replace or remove any

part of the appliance unless

specifically recommended in the

manuals. Improper installation,

service or maintenance can cause

injury or property damage. Refer to

this manual for guidance. All other

servicing should be done by an

authorized servicer.

Improper installation is not covered by

the warranty.

Appliance Handling Safety

Hidden surfaces may have sharp edges.

Use caution when reaching behind or

under appliance.

Safety Codes and Standards

This appliance complies with one or more

of the following Standards:

▯ UL 858, The Standard for the Safety of

Household Electric Ranges

▯ UL 923, The Standard for the Safety of

Microwave Cooking Appliances

▯ UL 507, The Standard for the Safety of

Electric Fans

▯ ANSI Z21.1 / CSA 1.1 Household Cooking

Gas Appliances

▯ CAN/CSA-C22.2 No. 113-M1984 Fans and

Ventilators

▯ CAN/CSA-C22.2 No. 61-M89 Household

Cooking Ranges

It is the responsibility of the owner and

the installer to determine if additional

requirements and/or standards apply to

specific installations.

Installation must conform with local

codes or, in the absence of local codes,

with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54 or, in Canada, the

Natural Gas and Propane Installation

Code, CSA B149.1.

The appliance must be electrically

grounded in accordance with local codes

or, in the absence of local codes, with the

National Electrical Code, NFPA 70 latest

edition or, in Canada, the Canadian

Electric Code, CSA C22.1-02.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

Electric Safety

9 WARNING

Before you plug in an electrical cord

or turn on power supply, make sure

all controls are in the OFF position.

For appliances equipped with a cord and

plug, do not cut or remove the ground

prong. It must be plugged into a matching

grounding type receptacle to avoid

electrical shock. If there is any doubt as

to whether the wall receptacle is properly

grounded, the customer should have it

checked by a qualified electrician.

If required by the National Electrical

Code (or Canadian Electrical Code), this

appliance must be installed on a separate

branch circuit.

The circuit breaker should have a contact

separation of at least 3 mm on all poles.

Be sure your appliance is properly

installed and grounded by a qualified

technician. Installation, electrical

connections and grounding must comply

with all applicable codes.

Before installing, turn power OFF at the

service panel. Lock service panel to

prevent power from being turned ON

accidentally.

Installer – show the owner the location of

the circuit breaker or fuse. Mark it for

easy reference.

Gas Safety

Install a gas shutoff valve near the

appliance. It must be easily accessible in

an emergency.

Leak testing must be conducted by the

installer according to the instructions in

this manual.

The appliance and its individual shutoff

valve must be disconnected from the gas

supply piping system during any pressure

testing at pressures in excess of ½ psi

(3.5 kPa).

The appliance must be isolated from the

gas supply piping system by closing its

individual manual shutoff valve during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than ½ psi (3.5 kPa).

The minimum supply pressure must be 1"

water column above the manifold

pressure printed on the data plate.

The maximum supply pressure must not

exceed 14.0 inches water column

(34.9 Millibars).

State of California Proposition 65 Warnings

9 WARNING

This product can expose you to

chemicals including vinyl chloride,

which is known to the State of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to

www.P65Warnings.ca.gov.

9 IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY NOTICE: Burning

gas cooking fuel generates some by-

products which are on the list of

substances which are known by the State

of California to cause cancer or

reproductive harm. To minimize exposure

to these substances, always operate this

unit according to the instructions

contained in this booklet and provide

good ventilation.

Propane Gas Installation

The propane gas tank must be equipped

with its own high pressure regulator. In

addition, the regulator supplied with this

unit must also be used.

The appliance is shipped from the factory

for use with natural gas. It must be

converted for use with propane. A

qualified technician or installer must do

the conversion.

This appliance has been certified for safe

operation up to a height of 10,000 ft

without any modifications. Exception: For

use with propane the appliance must be

converted per the LP conversion

instructions.

For Massachusetts installations:

▯ Installation must be performed by a

qualified or licensed contractor,

plumber or gas fitter qualified or

licensed by the state, province or

region where this appliance is being

installed.

▯ Shut-off valve must be a “T” handle gas

cock.

▯ Flexible gas connector must not be

longer than 36 inches.

Installer - show the owner where the gas

shut-off valve is located.

Related Equipment Safety

The appliance should only be used if

installed by a qualified technician in

accordance with these installation

instructions. The manufacturer is not

responsible for any damage resulting

from incorrect installation.

Remove all tape and packaging before

using the appliance. Destroy the

packaging after unpacking the appliance.

Never allow children to play with

packaging material.

Never modify or alter the construction of

the appliance. For example, do not

remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

To eliminate the risk of burns or fire by

reaching over heated surface units,

cabinet storage space located above the

surface units should be avoided. If

cabinet storage is to be provided, the risk

can be reduced by installing a hood that

projects horizontally a minimum of 5

inches (127 mm) beyond the bottom of

the cabinet.

Verify that cabinets above the cooktop are

a maximum of 13" (330 mm) deep.

When installing a cooktop over a single

oven, be sure to follow both the oven’s

and cooktop’s installation manuals.

Before You Begin en-us

Ventilation Recommendations

We strongly recommend the installation of a

ventilation hood above this appliance. The

hood must be installed according to

instructions furnished with the hood.

9 CAUTION

The appliance should not be installed

with a ventilation system that blows air

downward toward the burners. This

type of ventilation system may cause

ignition and combustion problems with

the gas cooking appliance resulting in

personal injury or unintended

operation.

Before You Begin

Tools and parts needed

▯ Screwdriver Torx T20

▯ Pencil

▯ Drill with ¼" (6 mm) bit

▯ Jigsaw

▯ Tape Measure

Note: Additional materials may be necessary for

installation in solid surface countertops. Contact the

countertop manufacturer.

Parts included

Special accessories

You can order the following accessories from your

specialist dealer:

AA 414 010 Ventilation molding, for operation

next to the VL 414 downdraft

ventilation

VA 420 000 Connection strip for combination

with other Vario appliances in the

400 series for flush installation

VA 420 001 Connection strip for combination

with other Vario appliances in the

400 series for flush installation with

appliance cover/compensation strip

en-us Before You Begin

Use the accessories only as indicated. The manufacturer

assumes no liability for incorrect usage of the

accessories.

Cabinet Requirements

The minimum spaces that must be maintained when

installing the gas cooktop shall be:

Countertop Requirements

9 WARNING

To reduce the risk of ignition of surrounding

combustible materials, install at least 12" (300 mm)

from both sidewalls and at least 4" (102 mm) from

the rear wall.

The countertop must be level and horizontal. The stability

of the countertop must be maintained after the cut-out

has been made.

Solid surface countertops often require special

installations. For example, heat-reflective tape and

rounded corners may be necessary. Contact the

countertop manufacturer for instructions specific to your

countertop.

Technical Data

VA 420 010 Connection strip for combination

with other Vario appliances in the

400 series for surface-mounted

installation

VA 420 011 Connection strip for combination

with other Vario appliances in the

400 series for surface-mounted

installation with appliance cover/

compensation strip

VA 450 900 Appliance extension 90 cm for depth

compensation for several Vario

appliances

A minimum 12" (300 mm)

B minimum 12" (300 mm)

C minimum 30" (762 mm) clearance between

the top of the cooking surface and the

bottom of the ventilation hood

D minimum 4" (102 mm)

for non-combustible back-walls the

minimum distance can be reduced to 1

(40 mm)

E minimum 36" (914 mm)

F minimum 18" (457 mm)

G maximum 13" (330 mm)

)

(

Total connected load electric 25 VA

Total connected load gas

(natural gas)

59,800 BTU/h

(17.5 kW)

Total consumption

(natural gas)

1.6 m³/h

Total connected load gas

(propane gas)

58,000 BTU/h

(17.0 kW)

Total consumption

(propane gas)

1,210 g/h

Prepare Installation Space en-us

Prepare Installation Space

The kitchen unit must be heat-resistant to at least

200° F (90°C). The stability of the unit must be

maintained after producing the cut-out.

Produce the cut-out in the countertop for one or more

Vario appliances as shown in the installation sketch. The

angle between the cut surface and the countertop must

be 90°.

The cut edges at the sides must be flat to ensure a good

fit of the retaining springs on the appliance. In laminated

worktops, it may be necessary to fit strips at the sides of

the cut-out.

Remove shavings after cutting. Seal cut surfaces for

resistance to heat and so they are watertight.

Pay attention to a minimum gap of 3/8“ (10 mm) from the

underside of the appliance to kitchen units.

Use suitable base constructions to ensure load-carrying

capacity and stability, especially in the case of thin

countertops. Pay attention to the weight of the appliance,

including any payload. Reinforcement material used must

be resistant to heat and moisture.

Note: Wait until the appliance has been installed in the

installation opening before checking that it is level.

Cutting out countertop

Flush mounting: Flush mounting into a countertop is

possible.

Flush installation: The appliance can be installed in the

following temperature- and water-resistant countertops:

▯ Stone countertops

▯ Plastic countertops (such as Corian®)

▯ Solid wood countertops: Only in consultation with the

manufacturer of the countertop (seal cut-out edges)

▯ Installation in other countertops only in consultation

with the manufacturer of the countertop.

Installation in countertops made of particleboard is not

possible.

Note: Any cut-out work on the countertop must be

performed in a workshop according to the installation

diagram. The cut-out must be made cleanly and precisely

since the cut-out edge is visible on the surface. Clean

and degrease the cut-out edges with a suitable cleaning

agent (bear in mind silicone manufacturer's processing

instructions).











PLQ

PLQ

PLQ

PLQ



PLQ





















 PP

15/16

±1/16





















PLQ

U















PLQ

PLQ





15/16"

PLQ











































±1/16

15/16

 PP

±1/16



PLQ





en-us Installation Procedure

Combining several Vario devices: The connecting strip VA

420 000/001/010/011 is required for the combination of

several Vario appliances. This is available separately as a

special accessory. Consider additional space

requirement for the connecting strip between the

appliances when making the cut-out (see installation

instructions VA 420 000/001/010/011).

Appliances can also be installed in individual cut-outs,

bearing in mind a minimum distance between the devices

of 2" (51 mm).

When combining several appliances with or without

appliance cover, you can use the appliance extensions

VA 450 110/-401/-600/-800/-900 (depending on

appliance width) to balance out dimension differences.

Drilled Hole for Control Knob

Possible types of installation:

▯ Installation in the front of the base cabinet

▯ Installation in the countertop next to the appliance

▯ Installation in the countertop in front of the appliance

Note: Follow the installation instructions provided for the

control knobs.

Installation Procedure

Mounting Control Knobs

Note: Follow the installation instructions provided for the

control knobs.

1. Depending on the distance between the control

knobs, it may be necessary to break off the retaining

plate at the perforation. Hold the retaining plate in

place against the back of the control panel or the

bottom of the countertop, or secure it with the

enclosed screws.

2. When installing a single control knob or when the

retaining plate has been broken at the perforation, use

2 screws to hold each individual retaining plate in

place to prevent it from rotating (C).

For stone countertops, use temperature-resistant two-

component adhesive (for metal to stone) to adhere the

retaining plate.

3. Remove the protective film on the back of the

illuminated ring (A).

4. Insert the control knob into the drilled hole (B) and

screw the nut on the back with the enclosed

installation aid (D).

5. Connect all of the control knobs with the enclosed

shorter cables. The plugs must snap into the sockets

(E).

Note: The two cable connectors on the control knob

are identical.

9$

9$





 PP

Installation Procedure en-us

6. Connect the longer cable to the control cable for

connection to the appliance. The plug must snap into

the socket (F).

Note: The appliance can be connected to any control

knob.

7. After installing, check that all plug connections fit

correctly.

8. After installing all the cables, secure them to the

retaining plate by bending the tab down (E).

Install Appliance

9 WARNING

Before you plug in an electrical cord or turn on

power supply, make sure all controls are in the OFF

position.

1. Connect the connection cable to the control cable in

the socket on the bottom of the appliance. The plug

must snap into place.

2. Insert appliance evenly into the cutout. Push it down

firmly into the cutout.

Note: The appliance must be firmly fixed in the cutout

and must not be able to move around (e.g., during

cleaning). If the width of the cutout is at the upper

tolerance limit, fasten the ledges at the sides in the

cutout if necessary.

(

)

en-us Installation Procedure

3. Only for flush mount installation:

Note: Make sure that everything is working correctly

before grouting.

Grout the surrounding gap with a suitable

temperature-resistant silicone adhesive (e.g.,

OTTOSEAL

S 70). Smooth the joint seal with a

smoothing agent recommended by the manufacturer.

Heed the processing instructions for the silicone glue.

Only start up the appliance after the silicone glue is

completely dry (at least 24 hours, depending on the

room temperature).

NOTICE

Unsuitable silicone adhesive causes permanent

discoloration to natural stone countertops.

4. Connect the appliance to the mains and check that it

works correctly. If the appliance is turned off, air may

be present in the gas line. Turn control knob to 0 and

reignite. Repeat the process until the appliance

ignites.

Connect Gas Supply

The appliance is shipped from the factory for use with

natural gas. It must be converted for use with propane. A

qualified technician or installer must do the conversion.

Before connecting the appliance, please check whether

the local connection conditions such as gas type and gas

pressure match the appliance settings.

Make sure the gas supply is turned off at the manual shut-

off valve before connecting the appliance.

The gas connection must be in a location that permits

access to the manual shut-off valve and which, if

applicable, is visible after opening the door of the

cabinet.

SERVICER INFO ONLY

Connect the gas supply using the ½" U.S.A. elbow and

the fiber gasket supplied with the unit. The shorter,

nontapered thread fits into the threaded nut on the hob.

The longer, tapered U.S.A. thread is for the incoming gas

supply. Vent the gas line, check for leaks. The gas

pressure regulator is supplied with the unit and comes

set for natural gas. To convert regulator to LP (propane)

gas:

Make-Maxitrol Model RV 47 CL ½ PSIG

1. Remove the aluminum cap from the top of the

regulator.

2. Remove the yellow plastic shaft from the cap by

pushing it sideways until it pops out of the groove in

the cap.

3. Turn the shaft over and push back into the cutout in

the cap.

4. Replace the cap on the regulator.

Connect Electrical Supply

Before connecting supply cord to wall receptacle, make

certain that gas shutoff valve and all burner controls are

in OFF position.

Electrical connection (AC 110-127 V) is established by

means of a connecting cord with a grounding contact

plug connected to a grounded socket, which must also

be accessible after installation of the gas cooktop.

Burner Cap Placement

The burner parts must be properly placed for the cooktop

to function properly. If the burner parts are not properly

placed, one or more of the following problems may occur:

▯ Burner flames are too high.

▯ Flames shoot out of burners.

▯ Burners do not ignite.

▯ Burner flames light unevenly.

▯ Burner emits gas odor.

Placing Burner Parts

After electrical connection is complete, assemble the

burner parts correctly and evenly. When assembling the

burner parts, make sure that the burner head is placed on

the base in such a way that the prongs of the burner cap

fit snugly into the groove of the burner base.

Installation Procedure en-us

Checking Burner Cap Placement

Check to make sure that there is no gap between the

burner parts. You may gently try to move the burner parts

from side to side to check if they are properly placed.

Check the Installation

Check operation of electric igniters. Check flame

characteristics. Flame should be blue with no yellow tip.

Yellow Flames:

Further adjustment is required.

Yellow Tips on Outer Cones:

Normal for LPG Gas.

Soft Blue Flames:

Normal for Natural Gas.

If the flame is completely or mostly yellow, verify that the

regulator is set for the correct fuel. After adjustment,

retest.

Some yellow streaking is normal during the initial start-

up. Allow unit to operate 4-5 minutes and re-evaluate

before making adjustments.

Removing the appliance

Disconnect the appliance from the power supply. Close

the gas shut-off valve. Remove the silicone joint from

appliances installed flush. Push out the appliance from

below.

NOTICE

Appliance damage! Do not lever out the appliance at the

frame from above.

en-us Conversion to another type of gas

Conversion to another type of gas

This gas stovetop corresponds to the categories

specified on the rating plate. By changing nozzles, it is

possible to convert the appliance to any of the gases

listed on the plate. The conversion kit can be obtained

from our customer service. With some models, the

conversion kit is included in the scope of delivery.

Only a licensed specialist is authorized to switch the

appliance to another gas type.

Before carrying out the conversion, turn off the electricity

and gas supply.

Replacing the Main Control Nozzles: Wok Burner

1. Remove the pan supports and all burner parts.

2. Unscrew the fastening nuts from the cooktop (3 nuts –

WAF 7), and carefully lift up the cooktop to remove it.

3. Remove the securing clips from the burner pipes. Pull

out the burner pipes. Unscrew the screw in the air

regulating sleeve. Remove the nozzle retaining head.

4. Pull off the nozzle and O-ring for the inner burner ring

by hand. Unscrew the nozzle for the outer burner ring

(WAF 10).

5. Check that the O-ring fits correctly in the new main

control nozzle for the inner burner ring. Fit the nozzle

to the burner pipe. Screw the new main nozzle for the

outer burner ring as far as it will go into the nozzle

retaining head.

6. Attach the nozzle retaining head and burner pipes.

Attach the securing clips.

7. After loosening the screw, adjust the air regulating

sleeve to the correct setting (see nozzle table).

Retighten the screw.

F

Z

Z

D D

F

D

F

F

D

Z

1*$:&





3URSDQH:&



RSHQ



1*$:&





3URSDQH:&



RSHQ



1*$:&





3URSDQH:&

$



D

/

D

/

F

/

F

/

Z

éPP

PP

Ȣ¼ȭȬPP

ç¼ȭȬPP

Z

Z

/!

/

Conversion to another type of gas en-us

8. Put the cooktop in place and tighten the screws

evenly. Put the burner parts and pan supports in

place, and ensure that they are positioned correctly.

9. Set the pressure regulator to the correct gas

pressure.

Replacing the Main Control Nozzles: Normal and High

Output Burners

1. Remove the pan supports and all burner parts.

2. Unscrew the fastening nuts from the cooktop (3 nuts –

WAF 7), and carefully lift up the cooktop to remove it.

3. Remove the securing clips from the burner pipes. Pull

out the burner pipes. The electrode can remain

connected. Unscrew the burners (Torx T20) and pull

out the burner pipes.

4. Remove the nozzles from the burner pipes by hand,

pull off the O-ring.

5. Check that the O-ring fits correctly in the new main

control nozzle. Pull the nozzles off of the burner

pipes. Do not bend the burner pipes!

6. Attach the burner pipes to the burners. Attach the

securing clips. Screw the burners into place.

7. After loosening the screw, adjust the air regulating

sleeve for the external burner to the correct setting

(see nozzle table – L1). Retighten the screw.

8. Adjust the air regulating sleeve for the inner burner by

turning or sliding it to the correct setting (see nozzle

table – L2).

9. Put the cooktop in place and tighten the screws

evenly. Put the burner parts and pan supports in

place, and ensure that they are positioned correctly.

Setting the Gas Type

Set the gas type via any control knob:

1. Turn the control knob to 0 (A). Disconnect the

appliance from the power supply. Wait for at least

30 seconds (B).

2. Reconnect the appliance (C). The illuminated ring

around the control knob will turn green for a second

and then turn yellow (D). Wait until the illuminated ring

goes out.

3. Turn the control knob counterclockwise to position 12

(E).

/

23(1 PP PP

/

V

en-us Conversion to another type of gas

4. Turn the control knob clockwise to position 1 (F).

5. Turn the control knob counterclockwise to position 0

(G). Wait until the illuminated ring turns yellow (H).

6. Set the gas type on the control knob (I), the currently

selected position will turn green:

7. Keep the control knob at the desired setting for at

least 5 seconds. The illuminated ring around the

control knob will turn green (I).

8. To save the setting, it is necessary to exit the menu as

follows: Turn the control knob to position 0 (J). Then

turn the control knob counterclockwise to position 12

(K).

Turn the control knob clockwise to position 1 (L). Turn

the control knob counterclockwise to position 0 (M).

Wait until the illuminated ring goes out (N).

The setting is saved. The illuminated ring around the

control knob will turn yellow for a second. Wait until the

illuminated ring goes out.

Checking functions after the conversion:

The flames are adjusted correctly if no yellow tips are

visible. They must not go out when switching over swiftly

from the high to the low setting.

Note: Stick the adhesive label included with the nozzle

set over the rating plate of the appliance to document the

changeover to a different gas type.

Control knob position Gas Type

7 NG A 6" WC

9 Propane 10" WC

)

(

)

3URSDQH:&

1*$:&

V

Customer Service en-us

Customer Service

If your appliance needs repairs, our customer service is

there for you. We work hard to help solve problems

quickly and without unnecessary service calls, getting

your appliance back up and running correctly in the least

amount of time possible.

When you call, please indicate the product number

(E-Nr.) and serial number (FD-Nr.) so that we can support

you in a qualified manner. You will find the type plate with

these numbers on the bottom of the appliance. To avoid

having to search for a long time when you need it, you

can enter your appliance data and the customer support

telephone number here.

Please read the use and care instructions provided with

your appliance. Failure to do so may result in an error in

using the appliance. This could result in a service call

that instead of fixing a mechanical issue is only needed

for customer education. Such calls are not covered by the

appliance warranty.

Please find the contact data of all countries in the

enclosed customer service list.

To book an engineer visit and product advice

You can rely on the manufacturer’s expertise. Rest

assured that the repair will be handled by trained service

technicians who have the original replacement parts for

your appliance.

E-Nr. FD-Nr.

Customer Service O

USA 877 442 4436

toll-free

CANADA 877 442 4436

toll-free

fr-ca Customer Service

Table des matières

Notice de montage

Définitions de sécurité 18

CONSIGNES DE SÉCURITÉ IMPORTANTES 19

Sécurité de manutention des appareils 20

Codes et normes de sécurité 20

Sécurité électrique 21

Sécurité en matière de gaz 21

Installation au gaz propane 22

Équipement de sécurité 23

Avant de commencer 24

Outils et pièces nécessaires 24

Pièces comprises 24

Accessoires spéciaux 24

Exigences pour les placards 24

Exigences pour le plan de travail 25

Caractéristiques techniques 25

Préparation des meubles 25

Découper le plan de travail 25

Procédure d'installation 27

Monter les boutons de commande 27

Pose de l'appareil 28

Branchement du gaz 29

Brancher l'alimentation électrique 29

Montage des chapeaux de brûleur 29

Vérification de l'installation 30

Dépose de l'appareil 30

Changement de type de gaz 30

Service après-vente 33

Vous trouverez des informations supplémentaires

concernant les produits, accessoires, pièces de

rechange et services sur Internet sous :

www.gaggenau.com et la boutique en ligne :

www.gaggenau.com/zz/store

Définitions de sécurité

9 AVERTISSEMENT

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures graves,

voire la mort.

9 ATTENTION

Ceci indique que le non-respect de cet

avertissement peut entraîner des blessures légères

ou de gravité moyenne.

AVIS

Ceci indique que la non-conformité à cet avis de sécurité

peut entraîner des dégâts matériels ou endommager

l'appareil.

Remarque : Ceci vous signale des informations et/ou

indications importantes.

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

LIRE ET CONSERVER CES INSTRUCTIONSSé c u r i t é en mat i èr e de gaz

1HSDVFRQVHUYHURXXWLOLVHUGHOHVVHQFHRX

GDXWUHVOLTXLGHVRXYDSHXUVLQIODPPDEOHVj

SUR[LPLWpGHFHWDSSDUHLORXGHWRXWDXWUHDSSDUHLO

48()$,5(6,92863(5&(9(=81(2'(85'(*$=



1HSDVHVVD\HUGHPHWWUHXQDSSDUHLOVRXVWHQVLRQ



1HSDVWRXFKHUGLQWHUUXSWHXUGHFRXUDQWpOHFWULTXH



1HSDVXWLOLVHUGHWpOpSKRQHVGDQVOpGLILFH



&RPPXQLTXHULPPpGLDWHPHQWDYHFOHIRXUQLVVHXU

GHJD]GHSXLVODSSDUHLOWpOpSKRQLTXHGXQYRLVLQ

5HVSHFWHUOHVGLUHFWLYHVGXIRXUQLVVHXUGHJD]



6LOVDYqUHLPSRVVLEOHGHMRLQGUHOHIRXUQLVVHXUGH

JD]FRPPXQLTXHUDYHFOHVSRPSLHUV

8WLOLVHUOHVVHUYLFHVGXQLQVWDOODWHXURXGXQHDJHQFH

GHVHUYLFHVTXDOLILpVRXOHIRXUQLVVHXUGHJD]SRXU

SURFpGHUjOLQVWDOODWLRQHWDX[UpSDUDWLRQV



$9(57,66(0(176LOHVGLUHFWLYHVQHVRQWSDV

VXLYLHVjODOHWWUHLO\DXQULVTXHGLQFHQGLHRX

GH[SORVLRQSRXYDQWHQWUDvQHUGHVGRPPDJHV

PDWpULDX[GHVEOHVVXUHVRXXQGpFqV

9 CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE ET CONSERVER CES INSTRUCTIONS

IMPORTANT : IL FAUT FAIRE POSER

L'APPAREIL PAR UN INSTALLATEUR

QUALIFIÉ.

INSTALLATEUR : LAISSEZ CES

INSTRUCTIONS AVEC L'APPAREIL

APRÈS UNE FOIS L'INSTALLATION

TERMINÉE. IMPORTANT : À

CONSERVER POUR L'USAGE DE

L'INSPECTEUR LOCAL.

9 AVERTISSEMENT

Si l’information de ce guide n’est

pas suivie exactement, il peut en

résulter un incendie ou un choc

électrique causant des dommages à

la propriété, des blessures ou la

mort.

9 AVERTISSEMENT

Ne réparez, remplacez, ni ne retirez

aucune partie de l'appareil, excepté

si les manuels recommandent de le

faire. Une installation, un entretien

ou une inspection incorrects peuvent

occasionner des blessures ou des

dommages matériels. Reportez-vous

au présent manuel pour obtenir des

indications. Toute autre intervention

doit être effectuée par un technicien

agréé.

Une installation non conforme peut

entraîner la perte de la garantie.

Sécurité de manutention des

appareils

Certaines surfaces peuvent avoir des

bords tranchants. Faire attention en

étendant le bras derrière l’appareil ou en

dessous.

Codes et normes de sécurité

Cet appareil est conforme à une ou

plusieurs des normes suivantes :

▯ UL 858, la norme en matière de sécurité

pour les cuisinières électriques

domestiques

▯ UL 923, la norme en matière de sécurité

pour les fours à micro-ondes

▯ UL 507, la norme en matière de sécurité

pour les ventilateurs électriques

▯ ANSI Z21.1/CSA 1.1, Appareils

électroménagers pour la cuisson à gaz

▯ CSA-C22.2 no 113-M1984, Ventilateurs

▯ CSA-C22.2 no 61-M89, Cuisinières

domestiques

Il incombe au propriétaire et à

l’installateur de déterminer si des

exigences et/ou normes additionnelles

s’appliquent pour des installations

spécifiques.

L’installation doit être conforme aux

codes locaux ou, en l’absence de tels

codes, au National Fuel Gas Code

ANSI Z223.1/NFPA 54 ou, au Canada, au

code national CSA B149.1 d’installation

du gaz naturel et du propane.

La page charge ...

Gaggenau VG425211CA Guide d'installation

Marque: Gaggenau

Modèle: VG425211CA

Catégorie: Cuisinières

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Gaggenau VG425211CA Installation guide
español: Gaggenau VG425211CA Guía de instalación
português: Gaggenau VG425211CA Guia de instalação

Gaggenau VG425211CA Guide d'installation

Ce manuel convient également à

Gaggenau VG425211CA Guide d'installation

dans d''autres langues

Documents connexes

Autres documents