Arthur_Martin ASF5206LOW Manuel utilisateur

Marque: Arthur_Martin

Modèle: ASF5206LOW

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Ce manuel convient également à

ASF5206LOX

ASF5206LOW

ASF5206LOX

EN Dishwasher User Manual 2

FR Lave-vaisselle Notice d'utilisation 21

CONTENTS

Safety information 2

Safety instructions 3

Product description 5

Control panel 6

Programmes 6

Settings 8

Before first use 10

Daily use 11

Hints and tips 13

Care and cleaning 14

Troubleshooting 16

Technical information 20

Subject to change without notice.

SAFETY INFORMATION

Before the installation and use of the appliance, carefully

read the supplied instructions. The manufacturer is not

responsible for any injuries or damage that are the result of

incorrect installation or usage. Always keep the instructions

in a safe and accessible location for future reference.

Children and vulnerable people safety

• This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

the use of the appliance in a safe way and understand the

hazards involved.

• Children between 3 and 8 years of age and persons with

very extensive and complex disabilities shall be kept away

from the appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away

from the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the

door is open.

• Children shall not carry out cleaning and user maintenance

of the appliance without supervision.

General Safety

• This appliance is intended to be used in household and

similar applications such as:

– farm houses; staff kitchen areas in shops, offices and

other working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the specification of this appliance.

• The operating water pressure (minimum and maximum)

must be between 0.5 (0.05) / 8 (0.8) bar (MPa)

• Follow the maximum number of 13 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualified persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp ends

pointing down or put them in the cutlery drawer in a

horizontal position with the sharp edges down.

• Do not leave the appliance with the open door unattended

to avoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the

appliance and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to

clean the appliance.

• If the appliance has ventilation openings in the base, they

must not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains using

the new supplied hose-sets. Old hose sets must not be

reused.

SAFETY INSTRUCTIONS

Installation

WARNING! Only a qualified

person must install this

appliance.

• Remove all the packaging.

• Do not install or use a damaged

appliance.

• Follow the installation instructions

supplied with the appliance.

• Always take care when moving the

appliance as it is heavy. Always use

safety gloves and enclosed footwear.

• Do not install or use the appliance

where the temperature is less than

0 °C.

• Install the appliance in a safe and

suitable place that meets installation

requirements.

Electrical connection

WARNING! Risk of fire and

electric shock.

• The appliance must be earthed.

• Make sure that the parameters on the

rating plate are compatible with the

electrical ratings of the mains power

supply.

• Always use a correctly installed

shockproof socket.

• Do not use multi-plug adapters and

extension cables.

• Make sure not to cause damage to the

mains plug and to the mains cable.

Should the mains cable need to be

replaced, this must be carried out by

our Authorised Service Centre.

• Connect the mains plug to the mains

socket only at the end of the

installation. Make sure that there is

access to the mains plug after the

installation.

• Do not pull the mains cable to

disconnect the appliance. Always pull

the mains plug.

• This appliance is fitted with a 13 A

mains plug. If it is necessary to change

the mains plug fuse, use only a 13 A

ASTA (BS 1362) fuse (UK and Ireland

only).

Water connection

• Do not cause damage to the water

hoses.

• Before connection to new pipes, pipes

not used for a long time, where repair

work has been carried out or new

devices fitted (water meters, etc.), let

the water flow until it is clean and clear.

• Ensure that there are no visible water

leaks during and after the first use of

the appliance.

• If the water inlet hose is damaged,

immediately close the water tap and

disconnect the mains plug from the

mains socket. Contact the Authorised

Service Centre to replace the water

inlet hose.

Use

• Do not put flammable products or items

that are wet with flammable products

in, near or on the appliance.

• Dishwasher detergents are dangerous.

Follow the safety instructions on the

detergent packaging.

• Do not drink and play with the water in

the appliance.

• Do not remove the dishes from the

appliance until the programme is

complete. Some detergent may remain

on the dishes.

• Do not store items or apply pressure on

the open door of the appliance.

• The appliance can release hot steam if

you open the door while a programme

operates.

Internal lighting

WARNING! Risk of injury.

• Concerning the lamp(s) inside this

product and spare part lamps sold

separately: These lamps are intended

to withstand extreme physical

conditions in household appliances,

such as temperature, vibration,

humidity, or are intended to signal

information about the operational status

of the appliance. They are not intended

to be used in other applications and are

not suitable for household room

illumination.

• To replace the internal lighting, contact

the Authorised Service Centre.

Service

• To repair the appliance contact the

Authorised Service Centre. Use original

spare parts only.

• Please note that self-repair or non-

professional repair can have safety

consequences and might void the

guarantee.

Disposal

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the

mains supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent

children and pets to get closed in the

appliance.

PRODUCT DESCRIPTION

The graphics below is just a

general product overview. For

more detailed information, refer

to other chapters and/or

documents provided with the

appliance.

Worktop

Upper spray arm

Lower spray arm

Filters

Rating plate

Salt container

Air vent

Rinse aid dispenser

Detergent dispenser

Cutlery basket

Lower basket

Upper basket

CONTROL PANEL

1 2 3

456

On/off indicator

Programme marker

Indicators

Delay button

Start button

Programme knob

Indicators

Indicator Description

Washing phase. It comes on when the washing phase operates.

Drying phase. It comes on when the drying phase operates.

End indicator.

Rinse aid indicator. It is always off while the programme operates.

Salt indicator. It is always off while the programme operates.

PROGRAMMES

The order of the programmes in the table may not reflect their sequence on the control

panel.

Programme Degree of

soil

Type of

load

Programme

phases

Consumption values

1)2)

Dura‐

tion

(min)

Energy

(kWh)

Water

(l)

Normal soil

Crockery

and cutlery

• Prewash

• Wash 50 °C

• Rinses

• Dry

227 1.039 11

Heavy soil

Crockery,

cutlery, pots

and pans

• Prewash

• Wash 70 °C

• Rinses

• Dry

155 -

170

1.5 - 1.7 14 - 15

Normal soil

Crockery

and cutlery

• Prewash

• Wash 65 °C

• Rinses

• Dry

130 -

140

1.4 - 1.6 15 - 17

Fresh soil

Crockery

and cutlery

• Wash 60 °C

or 65 °C

• Rinses

30 0.8 10

All • Prewash 14 0.1 5

The pressure and the temperature of the water, the variations of the mains supply, the options, the quantity of

dishes and the degree of soil can change the values.

The values for programmes other than ECO are indicative only.

This programme offers the most efficient use of water and energy consumption for crockery and cutlery with

normal soil. This is the standard programme for test institutes.

This programme is suitable for washing a load or a half load with fresh soil. It gives good washing results in a

short time.

With this programme, you can quickly rinse off food remains from dishes and prevent odours forming in the

appliance. Do not use detergent with this programme.

Information for test institutes

To receive the necessary information for conducting performance tests (e.g. according

to EN60436), send an email to:

[email protected]

In your request, include the product number code (PNC) from the rating plate.

For any other questions regarding your dishwasher, refer to the service book provided

with your appliance.

SETTINGS

Programme selection mode and

user mode

When the appliance is in programme

selection mode it is possible to set a

programme and to enter the user mode.

Settings available in the user mode:

• The level of water softener according to

the water hardness.

• Activation or deactivation of AirDry.

As the appliance stores the saved

settings, there is no need to configure

it before every cycle.

How to set the programme

selection mode

The appliance is in programme selection

mode when the on/off indicator is on and

Départ indicator flashes.

After activation, the appliance is in

programme selection mode by default. If

not, set the programme selection mode

the following way:

Press and hold simultaneously Départ

and Départ Différé until the appliance is

in programme selection mode.

The water softener

The water softener removes minerals from

the water supply, which would have a

negative effect on the washing results and

on the appliance.

The higher the content of these minerals,

the harder your water is. Water hardness

is measured in equivalent scales.

The water softener should be adjusted

according to the hardness of the water in

your area. Your local water authority can

advise you on the hardness of the water in

your area. It is important to set the right

level of the water softener to assure good

washing results.

Softening hard water increases

the consumption of water and

energy as well as the

programme duration. The

higher the level of water

softener, the higher the

consumption and the longer the

duration.

Water hardness

German de‐

grees (°dH)

French de‐

grees (°fH)

mmol/l Clarke de‐

grees

Water softener

level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

German de‐

grees (°dH)

French de‐

grees (°fH)

mmol/l Clarke de‐

grees

Water softener

level

<4 <7 <0.7 < 5

Factory setting.

Do not use salt at this level.

Regardless of the type of detergent

used, set the proper water hardness

level to keep the salt refill indicator

active.

Multi-tabs containing salt are

not effective enough to soften

hard water.

How to set the water softener

level

The appliance must be in programme

selection mode.

1. Make sure that the programme marker

on the knob is in on/off position.

2. To enter the user mode, press and

hold Départ Différé. At the same time

turn the knob counterclockwise until

the programme marker indicates the

first programme. Release the Départ

Différé when the indicators Départ

and on/off start flashing.

• The intermittent flashing of

shows the current setting, e.g. 5

flashes + pause + 5 flashes = level

3. Press Départ Différé repeatedly to

change the setting. Each pressing of

Départ Différé increases the level

number. After reaching level 10, the

count starts again from level 1.

4. To confirm the setting, turn the

programme knob until the programme

marker is again in on/off position

AirDry

AirDry improves the drying results with

less energy consumption. During the

drying phase, the door opens

automatically and remains ajar.

CAUTION! Do not try to close

the appliance door within 2

minutes after automatic

opening. This can cause

damage to the appliance.

AirDry is automatically activated with all

programmes excluding (if applicable).

The duration of the drying phase and the

door opening time vary depending on the

selected programme and options.

CAUTION! If children have

access to the appliance, it is

advised to deactivate AirDry as

opening the door may pose a

danger.

How to deactivate AirDry

The appliance must be in programme

selection mode.

Make sure that the programme marker on

the knob is set to on/off position.

1. To enter the user mode, press and

hold Départ Différé. At the same time

turn the knob counterclockwise until

the programme marker indicates the

first programme. Release Départ

Différé when the indicators Départ

and on/off start flashing.

2. Turn the knob counterclockwise until

the programme marker indicates the

second programme.

• The indicator shows the current

setting: on = AirDry is activated.

3. Press Départ Différé to change the

setting.

• If the indicator is off = AirDry is

deactivated.

4. To confirm the setting, keep turning

the programme knob until the

programme marker is back in the

on/off position.

BEFORE FIRST USE

1. Make sure that the current level of

the water softener agrees with the

hardness of the water supply. If not,

adjust the level of the water

softener.

2. Fill the salt container.

3. Fill the rinse aid dispenser.

4. Open the water tap.

5. Start a programme to remove any

processing residuals that can still be

inside the appliance. Do not use

detergent and do not put dishes in the

baskets.

After starting the programme, the

appliance recharges the resin in the water

softener for up to 5 minutes. The washing

phase starts only after this procedure is

complete. The procedure is repeated

periodically.

The salt container

CAUTION! Use rough salt

designed for dishwashers only.

Fine salt increases the risk of

corrosion.

The salt is used to recharge the resin in

the water softener and to assure good

washing results in daily use.

How to fill the salt container

1. Turn the cap of the salt container

counterclockwise and remove it.

2. Put 1 litre of water in the salt container

(only for the first time).

3. Fill the salt container with 1 kg of salt

(until it is full).

4. Carefully shake the funnel by its

handle to get the last granules inside.

5. Remove the salt around the opening of

the salt container.

6. Turn the cap of the salt container

clockwise to close the salt container.

CAUTION! Water and salt can

come out of the salt container

when you fill it. After you fill the

salt container, immediately

start a programme to prevent

corrosion.

How to fill the rinse aid

dispenser

A B

CAUTION! The compartment

(A) is for rinse aid only. Do not

fill it with detergent.

CAUTION! Only use rinse aid

designed specifically for

dishwashers.

1. Press the release button (D) to open

the lid (C).

2. Pour the rinse aid in the dispenser (A)

until the liquid reaches the fill level

'max'.

3. Remove the spilled rinse aid with an

absorbent cloth to prevent excessive

foam formation.

4. Close the lid. Make sure that the

release button locks into position.

You can turn the selector of the

released quantity (B) between

position 1 (lowest quantity) and

position 4 or 6 (highest

quantity).

DAILY USE

1. Open the water tap.

2. Turn the knob until the programme

marker is aligned with the programme

you want to set. Set the correct

programme for the type of load and the

degree of soil.

• If the salt indicators is on, fill the

salt container.

• If the rinse aid indicator is on, fill the

rinse aid dispenser.

3. Load the baskets.

4. Add the detergent.

5. Start the programme.

Using the detergent

1. Press the release button (B) to open

the lid (C).

2. Put the detergent, in powder or tablets,

in the compartment (A).

3. If the programme has a prewash

phase, put a small quantity of

detergent on the inner part of the

appliance door.

4. Close the lid. Make sure that the

release button locks into position.

For information about the

detergent dosage, refer to the

manufacturer's instructions on

the packaging of the product.

Usually, 20 - 25 ml of gel

detergent is adequate for

washing a load with normal

soil.

Do not fill the compartment (A)

with more than 30 ml of gel

detergent.

Using the multi-tablets

When you use tablets, that contain salt

and rinse aid, do not fill the salt container

and the rinse aid dispenser.

1. Adjust the water softener to the lowest

level.

2. Set the rinse aid dispenser to the

lowest position.

Setting and starting a

programme

Starting a programme

1. Open the water tap.

2. Close the appliance door.

3. Turn the knob until the programme

marker is aligned with the programme

you want to set.

• On/off indicator comes on.

• Start indicator starts to flash.

4. Press Départ.

• The programme starts and the

indicator of the washing phase is

on.

• On/off indicator and start indicator

are on.

Starting a programme with

delay start

1. Set the programme.

2. Press Départ Différé to delay the start

of the programme of 3 hours.

The delay indicator comes on.

3. Press Départ.

Start indicator comes on.

When the countdown is completed, the

programme starts.

Opening the door while the

appliance operates

Opening the door while a programme is

running stops the appliance. It may affect

the energy consumption and the

programme duration. After closing the

door, the appliance continues from the

point of interruption.

If the door is opened for more

than 30 seconds during the

drying phase, the running

programme ends. It does not

happen if the door is opened by

AirDry function.

Do not try to close the

appliance door within 2 minutes

after AirDry automatically

opens it as this may cause

damage to the appliance.

If, afterwards, the door is

closed for at least 3 minutes,

the running programme ends.

Cancelling the delay start while

the countdown operates

1. Press and hold Départ and Départ

Différé until the start indicator starts to

flash.

2. Press Départ to start the programme.

Cancelling the programme

Press and hold Départ and Départ

Différé until the start indicator starts to

flash.

Make sure that there is detergent in the

detergent dispenser before you start a

new programme.

End of the programme

When the programme is completed the

indicator is on. After 5 minutes of non-

use, the appliance enters standby mode

and all the indicators are off. It decreases

energy consumption.

1. To deactivate the appliance, turn the

programme knob until the programme

marker is in on/off position.

2. Close the water tap.

HINTS AND TIPS

General

Follow the hints below to ensure optimal

cleaning and drying results in daily use

and to protect the environment.

• Washing dishes in the dishwasher as

instructed in the user manual usually

consumes less water and energy than

washing dishes by hand.

• Load the dishwasher to its full capacity

to save water and energy. For best

cleaning results, arrange items in the

baskets as instructed in the user

manual and do not overload the

baskets.

• Do not pre-rinse dishes by hand. It

increases the water and energy

consumption. When needed, select a

programme with a prewash phase.

• Remove larger residues of food from

the dishes and empty cups and glasses

before putting them inside the

appliance.

• Soak or slightly scour cookware with

firmly cooked-on or baked-on food

before washing it in the appliance.

• Make sure that items in the baskets do

not touch or cover each other. Only

then can the water completely reach

and wash the dishes.

• You can use dishwasher detergent,

rinse aid and salt separately or you can

use the multi-tablets (e.g. ''All in 1'').

Follow the instructions on the

packaging.

• Select a programme according to the

type of load and the degree of soil.

offers the most efficient use of

water and energy consumption.

• To prevent limescale buildup inside the

appliance:

– Refill the salt container whenever

necessary.

– Use the recommended dosage of

the detergent and rinse aid.

– Make sure that the current level of

the water softener agrees with the

hardness of the water supply.

– Follow the instructions in the

chapter "Care and cleaning".

Using salt, rinse aid and

detergent

• Only use salt, rinse aid and detergent

for dishwasher. Other products can

cause damage to the appliance.

• In areas with hard and very hard water

we recommend to use plain dishwasher

detergent (powder, gel, tablets

containing no additional agents), rinse

aid and salt separately for optimal

cleaning and drying results.

• At least once a month run the

appliance with the use of appliance

cleaner which is particularly suitable for

this purpose.

• Detergent tablets do not fully dissolve

with short programmes. To prevent

detergent residues on the tableware,

we recommend that you use the tablets

with long programmes.

• Always use the correct quantity of

detergent. Insufficient dosage of

detergent can result in poor cleaning

results and hard-water filming or

spotting on the items. Using too much

detergent with soft or softened water

results in detergent residues on the

dishes. Adjust the amount of detergent

based on the water hardness. Refer to

the instructions on the detergent

packaging.

• Always use the correct quantity of rinse

aid. Insufficient dosage of rinse aid

decreases the drying results. Using too

much rinse aid results in bluish layers

on the items.

• Make sure that the water softener level

is correct. If the level is too high, the

increased quantity of salt in the water

might result in rust on cutlery.

What to do if you want to stop

using multi-tablets

Before you start to use separately

detergent, salt and rinse aid do the

following procedure.

1. Set the highest level of the water

softener.

2. Make sure that the salt and rinse aid

containers are full.

3. Start the shortest programme with a

rinsing phase. Do not add detergent

and do not put dishes in the baskets.

4. When the programme is completed,

adjust the water softener according to

the water hardness in your area.

5. Adjust the released quantity of rinse

aid.

Loading the baskets

• Always use the whole space of the

baskets.

• Use the appliance to wash dishwasher-

safe items only.

• Do not wash in the appliance items

made of wood, horn, aluminium, pewter

and copper as they could crack, warp,

get discoloured or pitted.

• Do not wash in the appliance items that

can absorb water (sponges, household

cloths).

• Put hollow items (cups, glasses and

pans) with the opening facing

downwards.

• Make sure that glasses do not touch

each other.

• Put light items in the upper basket.

Make sure that the items do not move

freely.

• Put cutlery and small items in the

cutlery basket.

• Make sure that the spray arms can

move freely before you start a

programme.

Before starting a programme

Before you start the selected programme,

make sure that:

• The filters are clean and correctly

installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is enough salt and rinse aid

(unless you use multi-tablets).

• The arrangement of the items in the

baskets is correct.

• The programme is suitable to the type

of load and the degree of soil.

• The correct quantity of detergent is

used.

Unloading the baskets

1. Let the tableware cool down before

you remove it from the appliance. Hot

items can be easily damaged.

2. First remove items from the lower

basket, then from the upper basket.

After the programme is

completed, water can still

remain on the inside surfaces

of the appliance.

CARE AND CLEANING

WARNING! Before

maintenance, deactivate the

appliance and disconnect the

mains plug from the main

socket.

Dirty filters and clogged spray

arms decrease the washing

results. Make a check regularly

and, if necessary, clean them.

Cleaning the filters

The filter system is made of 3 parts.

1. Turn the filter (B) counterclockwise

and remove it.

2. Remove the filter (C) out of filter (B).

3. Remove the flat filter (A).

4. Wash the filters.

Make sure that there are no residues

of food or soil in or around the edge of

the sump.

6. Put back in place the flat filter (A).

Make sure that it is correctly positioned

under the 2 guides.

7. Reassemble the filters (B) and (C).

8. Put back the filter (B) in the flat filter

(A). Turn it clockwise until it locks.

CAUTION! An incorrect

position of the filters can cause

bad washing results and

damage to the appliance.

Cleaning the spray arms

Do not remove the spray arms. If the holes

in the spray arms are clogged, remove

remaining parts of soil with a thin pointed

object.

External cleaning

• Clean the appliance with a moist soft

cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive

cleaning pads or solvents.

Internal cleaning

• Carefully clean the appliance, including

the rubber gasket of the door, with a

soft damp cloth.

• If you regularly use short duration

programmes, these can leave deposits

of grease and limescale inside the

appliance. To prevent this, we

recommend to run long duration

programmes at least 2 times per

month.

• To maintain the performance of your

appliance at its best, we recommend to

use monthly a specific cleaning product

for dishwashers. Follow carefully the

instructions on the packaging of the

product.

TROUBLESHOOTING

WARNING! Improper repair of

the appliance may pose a

danger to the safety of the

user. Any repairs must be

performed by qualified

personnel.

The majority of problems that can

occur can be solved without the need

to contact an Authorised Service

Centre.

Refer to the below table for information on

possible problems.

With some problems, the dedicated

indicator flashes intermittently to indicate a

malfunction and the alarm code.

Problem and alarm code Possible cause and solution

You cannot activate the appliance. • Make sure that the mains plug is connected to

the mains socket.

• Make sure that there is no damaged fuse in the

fuse box.

The programme does not start. • Make sure that the appliance door is closed.

• Press the start button.

• If the delay start is set, cancel the setting or wait

for the end of the countdown.

• The appliance recharges the resin inside the

water softener. The duration of the procedure is

approximately 5 minutes.

Problem and alarm code Possible cause and solution

The appliance does not fill with water.

• The indicator flashes 1 time in‐

termittently.

• The light related to the start button

flashes continuously.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply

is not too low. For this information, contact your

local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the filter in the inlet hose is not

clogged.

• Make sure that the inlet hose has no kinks or

bends.

The appliance does not drain the wa‐

ter.

• The indicator flashes 2 times

intermittently.

• The light related to the start button

flashes continuously.

• Make sure that the sink spigot is not clogged.

• Make sure that the interior filter system is not

clogged.

• Make sure that the drain hose has no kinks or

bends.

The anti-flood device is on.

• The indicator flashes 3 times

intermittently.

• The light related to the start button

flashes continuously.

• Close the water tap.

• Make sure that the appliance is correctly instal‐

led.

• Make sure the baskets are loaded as instructed

in the user manual.

The appliance stops and starts more

times during operation.

• It is normal. It provides optimal cleaning results

and energy savings.

The programme lasts too long. • If the delayed start option is set, cancel the de‐

lay setting or wait for the end of the countdown.

• Refer to the consumption values table in the

chapter "Programmes".

Small leak from the appliance door. • The appliance is not levelled. Loosen or tighten

the adjustable feet (if applicable).

• The appliance door is not centred on the tub.

Adjust the rear foot (if applicable).

The appliance door is difficult to close. • The appliance is not levelled. Loosen or tighten

the adjustable feet (if applicable).

• Parts of the tableware are protruding from the

baskets.

The appliance door opens during the

wash cycle.

• The AirDry function is activated. You can deacti‐

vate the function. Refer to "Settings".

Rattling/knocking sounds from inside

the appliance.

• The tableware is not properly arranged in the

baskets. Refer to basket loading leaflet.

• Make sure that the spray arms can rotate freely.

Problem and alarm code Possible cause and solution

The appliance trips the circuit-beaker. • The amperage is insufficient to supply simulta‐

neously all the appliances in use. Check the

socket amperage and the capacity of the meter

or turn off one of the appliances in use.

• Internal electrical fault of the appliance. Contact

an Authorised Service Centre.

Refer to "Before first use",

"Daily use", or "Hints and

tips" for other possible causes.

Once you have checked the appliance,

press the start button. If the problem

occurs again, contact an Authorised

Service Centre.

For alarm codes not described in the

table, contact an Authorised Service

Centre.

WARNING! We do not

recommend using the

appliance until the problem has

been completely fixed. Unplug

the appliance and do not plug it

in again until you are certain

that it operates correctly.

The washing and drying results are not satisfactory

Problem Possible cause and solution

Poor washing results. • Refer to "Daily use", "Hints and tips" and basket load‐

ing leaflet.

• Use more intensive washing programmes.

• Clean spray arm jets and filter. Refer to "Care and

Cleaning".

Poor drying results. • Tableware has been left for too long inside a closed ap‐

pliance.

• There is no rinse aid or the dosage of rinse aid is not

enough. Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• For the best drying performance activate AirDry.

• We recommend to always use rinse aid, even in combi‐

nation with multi-tablets.

There are whitish streaks or

bluish layers on glasses and

dishes.

• The release quantity of rinse aid is too much. Adjust the

rinse aid level to a lower level.

• The quantity of detergent is too high.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufficient. Adjust

the rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

Problem Possible cause and solution

The dishes are wet. • For the best drying performance activate AirDry.

• The programme does not have a drying phase or has a

drying phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a

different brand or activate the rinse aid dispenser and

use rinse aid and multi-tablets together.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the

humidity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent designed specifically for dishwashers.

• Use a detergent from a different manufacturer.

• Do not pre-rinse dishes under running water before put‐

ting them in the appliance.

Traces of rust on cutlery. • There is too much salt in the water used for washing.

Refer to "The water softener".

• Silver and stainless steel cutlery were placed together.

Avoid to put silver and stainless steel items close togeth‐

er.

There are residues of deter‐

gent in the dispenser at the

end of the programme.

• The detergent tablet got stuck in the dispenser and

therefore was not completely washed away by water.

• Water cannot wash away the detergent from the dis‐

penser. Make sure that the spray arm is not blocked or

clogged.

• Make sure that items in the baskets do not impede the

lid of the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Limescale deposits on the ta‐

bleware, on the tub and on the

inside of the door.

• The level of salt is low, check the refill indicator.

• The cap of the salt container is loose.

• Your tap water is hard. Refer to "The water softener".

• Even using multi-functional tabs use salt and set regen‐

eration of the water softener. Refer to "The water soft‐

ener".

• If lime scale deposits still remain, clean the appliance

with appliance cleaners which are particularly suitable

for this purpose.

• Try different detergent.

• Contact the detergent manufacturer.

Dull, discoloured or chipped

tableware.

• Make sure that only dishwasher-safe items are washed

in the appliance.

• Load and unload the basket carefully. Refer to basket

loading leaflet.

• Place delicate items in the upper basket.

Refer to "Before first use",

"Daily use" or "Hints and

tips" for other possible causes.

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 600 / 850 / 625

Electrical connection

Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

max 60 °C

Capacity Place settings 13

Power consumption Left-on mode (W) 5.0

Off-mode (W) 0.50

Refer to the rating plate for other values.

If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to de‐

crease energy consumption.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put

the packaging in relevant containers to

recycle it. Help protect the environment

and human health by recycling waste of

electrical and electronic appliances. Do

not dispose of appliances marked with the

symbol with the household waste.

Return the product to your local recycling

facility or contact your municipal office.

La page charge ...

Arthur_Martin ASF5206LOW Manuel utilisateur

Marque: Arthur_Martin

Modèle: ASF5206LOW

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Ce manuel convient également à

ASF5206LOX

Télécharger le PDF

rapport

dans d''autres langues

English: Arthur_Martin ASF5206LOW User manual

Arthur_Martin ASF5206LOW Manuel utilisateur

Ce manuel convient également à

Arthur_Martin ASF5206LOW Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents