Samsung DW80K5050 Series Guide d'installation

Marque: Samsung

Modèle: DW80K5050 Series

Taper: Guide d'installation

Ce manuel convient également à

DW80K7050 Series

imagine the possibilities

Thank you for purchasing this Samsung product.

DW80K7050 Series

DW80K5050 Series

Dishwasher

installation guide

These installation instructions are intended

for use by qualiﬁ ed installers.

If you are having problems installing this dishwasher

Please call : 1-800-SAMSUNG (726-7864)

for assistance : www.samsung.com

STOP

Installation_DD81-02034B-00_EN.indd 1Installation_DD81-02034B-00_EN.indd 1 5/10/2016 10:55:54 AM5/10/2016 10:55:54 AM

2_ safety instructions

safety instructions

Throughout this manual, you’ll see Warning and Caution notes. These warnings,

cautions, and the important safety instructions that follow do not cover all

possible conditions and situations that may occur. It’s your responsibility to use

common sense, caution, and care when installing, maintaining, and operating the

dishwasher. Samsung is not liable for damages resulting from improper use.

IMPORTANT SAFETY INSTRUCTIONS

What the icons and signs in this installation guide mean:

WARNING

Hazards or unsafe practices that may result in severe personal injury or

death.

CAUTION

Hazards or unsafe practices that may result in personal injury or property

damage.

CAUTION

To reduce the risk of ﬁ re, explosion, electric shock, or personal injury when

using the dishwasher, follow these basic safety precautions:

Follow directions explicitly.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

These warning signs are here to prevent injury to you and others.

Please follow them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

Install and store the dishwasher inside, away from exposure to weather.

Do not install the dishwasher near electrical components. Keep the dishwasher away from

open ﬂ ames.

Do NOT install the dishwasher on a carpet as this is a ﬁ re hazard.

Do NOT install the dishwasher in a location where the water may freeze (where the

temperature falls below 32 ˚F (0 ˚C)). Frozen water in the hoses or pipes may damage the

dishwasher.

As with all equipment using electricity, water and moving parts, potential hazards exist. To

safely operate this appliance, become familiar with its operation and exercise care when

using it.

The dishwasher must be properly grounded. Never connect it to an ungrounded outlet.

Prior to removal of original dishwasher and the installation of your new unit, make sure to

switch o your circuit breaker. Do not connect the dishwasher until you have completed the

installation. Connecting the power cable is the last step when installing the dishwasher.

All wiring and grounding must be done in accordance with the electrical code applicable to

the region.

CAUTION

Installation_DD81-02034B-00_EN.indd Sec1:2Installation_DD81-02034B-00_EN.indd Sec1:2 5/10/2016 10:56:00 AM5/10/2016 10:56:00 AM

safety instructions _3

GROUNDING INSTRUCTIONS

For a permanently connected appliance:

This appliance must be connected to grounded metal, a permanent wiring system, or an

equipment-grounding conductor must be run with the circuit conductors and connected to

the equipment-grounding terminal or lead on the appliance.

The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or

more people are needed to move a dishwasher and avoid potential injuries.

If the power cable is damaged, it must be replaced by the manufacturer, a service agent or

similarly qualiﬁ ed person in order to avoid a hazard.

Do not touch the power cable with wet hands.

Do not connect another appliance to the same power outlet as the dishwasher.

Make sure to use a new water supply line. Old lines are susceptible to breakage because

they become hardened and may cause property damage due to a water leakage.

The dishwasher must be connected to a hot water supply with a temperature between 120

˚F (49 ˚C) ~ 149 °F (65 ˚C). This temperature range provides the best washing result and

shortest cycle time. Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to

dishes.

Ensure that the water supplied to the dishwasher does not freeze. Frozen water can

damage the hoses, valves, pump, or other components.

Certiﬁ ed residential dishwashers are not intended for licensed food establishments.

(NSF/ANSI Standard 184 for Residential Dishwashers)

For a full list of safety information, please refer to the User Manual.

BEFORE INSTALLING THE DISHWASHER

WARNING

Tip-Over Hazard

- Do not use the dishwasher until it is correctly installed.

- Do not push down on the door when it is open.

- Do not place excessive weight on the open door.

Electric Shock Hazard

Failure to follow these instructions can result in death, ﬁ re, or electric shock:

- Electrically ground the dishwasher

- Connect the ground wire to the green ground connector in the junction box.

- Do not use an extension cord.

To reduce the risk of electric shock, ﬁ re, or injury to persons, the installer must ensure that

the dishwasher is completely enclosed at the time of installation.

CAUTION

WARNING

Installation_DD81-02034B-00_EN.indd Sec1:3Installation_DD81-02034B-00_EN.indd Sec1:3 5/10/2016 10:56:00 AM5/10/2016 10:56:00 AM

4_ contents

contents

PREPARING THE DISHWASHER

ENCLOSURE

5 Product dimensions

5 Enclosure dimensions

INSTALLING THE DISHWASHER

6 STEP 1 Check the parts and tools

8 STEP 2 Select the best location for the

dishwasher

9 STEP 3 Check water supply requirements

and cautions

10 STEP 4 Check the electrical requirements

and cautions

11 STEP 5 Unpacking and inspecting the

dishwasher

13 STEP 6 Preparing the dishwasher

14 STEP 7 Placing the dishwasher and

connecting the hot water supply

line

15 STEP 8 Leveling the dishwasher

16 STEP 9 Securing the dishwasher

17 STEP 10 Connecting the drain hose

20 STEP 11 Wiring connections

21 STEP 12 Completing the installation

SPECIFICATIONS

Installation_DD81-02034B-00_EN.indd Sec2:4Installation_DD81-02034B-00_EN.indd Sec2:4 5/10/2016 10:56:00 AM5/10/2016 10:56:00 AM

preparing the dishwasher enclosure _5

01 PREPARING THE DISHWASHER

preparing the dishwasher

enclosure

PRODUCT DIMENSIONS

ENCLOSURE DIMENSIONS

This dishwasher is designed to be enclosed

on the top and on both sides by a standard

residential kitchen cabinet unit.

The installation enclosure must be clean and free

of any obstructions.

The enclosure must be at least 24 inches wide,

24 inches deep, and 34 1/8 inches high.

For the front door of the dishwasher to be ﬂ ush

with the leading edge of the counter top, the

counter top must be at least 25 inches deep.

Side view

DW80K7050 Series

Side view

DW80K5050 Series

Rear view

27” (686 mm)

20 ½ ” (520 mm)

24 ⅔” (627mm)

⁄

” (605 mm)

” (860 mm)

20 ½ ” (520 mm)

24 ⅔” (627 mm)

24 ½” (621.5 mm) - DW80J3020

5” (128 mm)

2 ⅓” (60 mm)

The water supply

line, power cable

and drain hose

should go through

this space behind

the dishwasher.

Then, the power

cable run in

channels under

the dishwasher to

connections in the

front.

24” (610 mm)

minimum

24” (610 mm)

minimum

34 ⅛” (867 mm)

minimum

Installation_DD81-02034B-00_EN.indd Sec5:5Installation_DD81-02034B-00_EN.indd Sec5:5 5/10/2016 10:56:00 AM5/10/2016 10:56:00 AM

6_ installing the dishwasher

installing the dishwasher

Be sure that you or your installer follow these instructions closely so that the new

dishwasher works properly and that you’re not at risk of injury when washing dishes.

STEP 1 CHECK THE PARTS AND TOOLS

Before starting on the installation, prepare all the necessary tools and parts required to install the

dishwasher. This will save installation time and simplify the installation process.

Parts required

Provided with the dishwasher. Check when you unbox the dishwasher in Step 5.

2 Installation Brackets

2 Flat Head Screws

(For the installation

bracket)

2 Screws

(for the kick plate)

Kick Plate

Protective sticker

Not provided

Power cable

Twist on wire

connector

Strain relief

Electrical tape &

Standard duct tape

Hot water supply line

Tube ﬁ ttings

Teﬂ on

tape or sealing

compound

Hose clamp Air gap Rubber connector

Installation_DD81-02034B-00_EN.indd Sec3:6Installation_DD81-02034B-00_EN.indd Sec3:6 5/10/2016 10:56:00 AM5/10/2016 10:56:00 AM

(90° Fitting

¾”

)

For the hot water supply line – We strongly recommend using

” minimum O.D. copper tubing with a

compression ﬁ tting or a ﬂ exible stainless steel braided hot water supply line.

[Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside

the tube ﬁ tting.]

You also need a 90° elbow with

” N.P.T. external pipe threads on one end and a ﬁ tting sized to ﬁ t

your hot water supply line (copper tubing/compression ﬁ tting or braided hose) on the other.

For the power cable, we recommend a jacketed 12-2 cable with ground. Note that some local codes

may require the cable to have a BX style metal jacket.

installing the dishwasher _7

02 INSTALLING THE DISHWASHER

Tools required

Electric drill Safety glasses Gloves Flashlight

Adjustable wrench Wire stripper Pliers Nipper

Tape measure Pencil Phillips screwdriver Flat screwdriver

Tubing cutter Cutting knife Hole saw Level

Torx t20 Hex L-wrench

Installation_DD81-02034B-00_EN.indd Sec3:7Installation_DD81-02034B-00_EN.indd Sec3:7 5/10/2016 10:56:01 AM5/10/2016 10:56:01 AM

8_ installing the dishwasher

New installation

If the dishwasher is a new installation, most of the installation work must be done before the

dishwasher is moved into place.

Replacement

If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections

for compatibility with the new dishwasher. Repace the existing connections as necessary.

STEP 2 SELECT THE BEST LOCATION FOR THE DISHWASHER

The following criteria are important to ensure the best location for the dishwasher:

- The location must have a solid ﬂ oor that is able to support the weight of the dishwasher.

- The location must be near a sink with easy access to the water supply, drain, and electrical

outlet.

For the drain to operate properly, the dishwasher should be installed within 9.8 ft (3 m) of

the sink.

- The location must let you load your dishes into the dishwasher easily.

- The location must have su cient space for the dishwasher door to open easily and provide

enough space between the dishwasher and the cabinet sides (at least 0.1 in (2 mm)).

If the dishwasher is installed in a corner, ensure that the side of the dishwasher is more than

2 in. (50 mm) from the wall or cabinet to its right or left.

- The wall at the back must be free of obstructions.

If this is a new installation, follow these steps:

1. Using a 2 ½ inch hole saw, cut a hole into the side of the cabinet that holds the sink as

shown in Figure 1-1 below.

2. If the base inside the sink cabinet is raised above the kitchen ﬂ oor and is higher than the

connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet

side as shown in Figure 1-2.

Depending on where your electrical outlet is, you may need to cut a hole in the opposite

cabinet side.

The hole for the water supply line, drain hose and

power cables.

installing the dishwasher

Installation_DD81-02034B-00_EN.indd Sec3:8Installation_DD81-02034B-00_EN.indd Sec3:8 5/10/2016 10:56:02 AM5/10/2016 10:56:02 AM

installing the dishwasher _9

02 INSTALLING THE DISHWASHER

STEP 3 CHECK WATER SUPPLY REQUIREMENTS AND CAUTIONS

• The hot water supply line pressure must be between 20~120 psi (140~830 kPa).

• Adjust the water heater to deliver water between 120 ˚F (49 ˚C) ~ 149 ˚F (65 ˚C).

- The dishwasher must be connected to a hot water supply between 120 ˚F (49 ˚C) ~ 149 ˚F

(65 ˚C). This temperature range provides the best washing result and shortest cycle time.

Temperature should not exceed 149 ˚F (65 ˚C) to prevent damage to dishes.

- Ensure that the water supply valve is turned o before connecting the hot water supply line to

the dishwasher.

- Seal the hot water supply line connections using teﬂ on tape or sealing compound to stop any

water leakage.

- The drain hose connected to the dishwasher must be run through the hole in the side wall so

it can be connected to the drain outlet of the sink. When you install the dishwasher, ensure

there is nothing on the drain hose and be careful not to tear it during the installation process.

Hot Water

Supply Line

Dishwasher bottom

Power cable

5¹⁄

3~7¹⁄3 in.

(135 ~ 185mm)

Installation_DD81-02034B-00_EN.indd Sec3:9Installation_DD81-02034B-00_EN.indd Sec3:9 5/10/2016 10:56:02 AM5/10/2016 10:56:02 AM

10_ installing the dishwasher

STEP 4 CHECK THE ELECTRICAL REQUIREMENTS AND CAUTIONS

The electrical requirements for the dishwasher are as follows:

• In the United States, install in accordance with the National Electric Code/State and Municipal codes

and/or local codes.

• In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and

Municipal codes and/or local codes.

• For cable direct connections.

- Use ﬂ exible, armored or non-metallic sheathed, copper wire with a grounding wire that meets the

wiring requirements for your local codes and ordinances.

- Use the strain relief method provided with the wiring junction box or install a U.L.-listed/CSA-certiﬁ ed

clamp connector to the wiring junction box. If using conduit, use a U.L.-listed/CSA-certiﬁ ed conduit

connector.

• For power cord connections

- The power supply cord must plug into a mating three prong, grounded outlet, located in the cabinet

next to the dishwasher opening. The outlet must meet your local codes and ordinances. Use a U.L.-

listed/CSA-certiﬁ ed power cord kit.

- The dishwasher must be connected to an electrical supply that provides the voltage and

amperage marked on the rating plate of the unit: 15 amps, 120 volts, 60Hz AC.

- Ensure that the circuit breaker connected to the dishwasher is o .

- The power cable must not extend more than 4 ft (1.2 m) from the side of the dishwasher.

- Check with a qualiﬁ ed electrician or serviceman if you are unsure whether the dishwasher is

properly connected.

- Do not connect another appliance to the same power outlet as the dishwasher.

- Before connecting the power cable to the dishwasher, ensure that there are no electrical

hazards (which may result in ﬁ re, explosion, electric shock, or personal injury).

- The power cable must pass through the channel on the bottom of the dishwasher as shown

in Figure 3.

installing the dishwasher

Hot Water

Supply Line

Dishwasher bottom

Power cable

5¹⁄

3~7¹⁄3 in.

(135 ~ 185mm)

Installation_DD81-02034B-00_EN.indd Sec3:10Installation_DD81-02034B-00_EN.indd Sec3:10 5/10/2016 10:56:03 AM5/10/2016 10:56:03 AM

installing the dishwasher _11

02 INSTALLING THE DISHWASHER

STEP 5 UNPACKING AND INSPECTING THE DISHWASHER

Unbox the dishwasher in an open area free of obstruction both around the carton and overhead. We

recommend that you retain the carton and all of the packing materials until the dishwasher is fully installed

and operational to ensure you have removed all the product’s components from the carton prior to disposal.

Unboxing

1. Position the carton right-side-up with top arrows pointing upwards.

2. Unbuckle or cut the four straps securing the carton top.

3. Lift the top of the telescoping carton clear of the carton tray and the contents, and then turn

it over and place it on the ﬂ oor.

4. Put the straps and all of the packing materials from around the dishwasher inside the carton

top, inspecting them for any signs of damage.

5. Locate and set aside the dishwasher's kick plate. The Kick plate is attached to packing

material of the dishwasher.

6. Lift the dishwasher from the carton tray, and then place it on the ﬂ oor.

Put the tray into the carton top.

7. Remove the bag that protects the dishwasher during shipping.

ALWAYS LIFT THE Dishwasher TO MOVE IT. Sliding it over rough surfaces can damage the

dishwasher’s feet and sliding the feet over ﬁ nished surfaces can, in some cases, damage

that ﬁ nish or the underlying surface.

8. There is also packing inside the dishwasher that you may want to leave in place until the

dishwasher is installed.

9. DO NOT, under any circumstances, remove the sound-absorbent padding that surrounds

the exterior of the tub of the dishwasher.

Inspecting

Mechanical

1. Check the plastic base assembly to ensure that it is intact

2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level

and secure the dishwasher.

3. Check all the visible components on the bottom of the dishwasher to ensure they are intact

and secure.

4. Check the door latch, the operation of the hinges, and conﬁ rm the door is properly secured

to the dishwasher.

Kick plate

CAUTION

Installation_DD81-02034B-00_EN.indd Sec3:11Installation_DD81-02034B-00_EN.indd Sec3:11 5/10/2016 10:56:03 AM5/10/2016 10:56:03 AM

12_ installing the dishwasher

installing the dishwasher

Plumbing

1. Check the hot water connection on the front left-side of the base of the dishwasher.

The mounting plate should be secured to the front of the base, the threads inside the

connection should be smooth and shiny, and the area should be clean and free of any

debris.

2. Check the plastic Brake and Sensor cases to ensure these assemblies are not cracked and

that all connections are secure.

3. Check the drain hose for any holes or deformities that could allow a water leak during

draining.

Electrical

1. Conﬁ rm the junction box cover is secured to the junction box on the front right-side of the

base of the dishwasher.

2. Conﬁ rm the electrical box was not damaged during shipping and that it is secured to the

base of the dishwasher.

Appearance

1. Conﬁ rm there are no dents or scratches on the front of the dishwasher.

2. Check the edges of the doors for any roughness or cracking

3. Check the control panel to ensure it is clear and unscratched, and that all the control markers

are in their proper places.

Parts

1. Conﬁ rm you have all the parts listed in Step 1 on page 6.

STEP 6 PREPARING THE DISHWASHER

1. Install the Protective sticker

Attach the Protective sticker to the bottom of the counter top as shown in the picture.

Installation_DD81-02034B-00_EN.indd Sec3:12Installation_DD81-02034B-00_EN.indd Sec3:12 5/10/2016 10:56:03 AM5/10/2016 10:56:03 AM

installing the dishwasher _13

02 INSTALLING THE DISHWASHER

2. Ensure that the circuit breaker and water supply valve are turned o before proceeding with

the following steps.

Before you move or lay down the dishwasher for installation, make sure to adjust the height

of the legs so the legs are as short as possible. This prevents the legs from breaking.

Level the dishwasher by adjusting the height of the legs after you have the dishwasher in

place.

3. Make sure there are no kinks and that the hose is not bent at any extreme angles that could

constrict the ﬂ ow of water.

4. Remove the junction box cover located at the bottom front right of the dishwasher using a

screwdriver, and then Install the strain relief (Figure 4 - C). Make sure to keep the junction box

cover you removed. It is used in Step 11, Wiring Connections.

5. If the countertop is made of wood or a material that is not damaged by drilling, attach the

two (2) Installation brackets that were supplied with the dishwasher using the supplied

screws (Figure 4 - A). They will be used in Step 9, Securing the Dishwasher.

Junction box

Strain relief

CAUTION

Do not overtighten the 90˚ elbow.

(Below 280 lb·in (31.6 N·m))

Doing so may damage the water inlet valve

and cause a water leak.

Installation_DD81-02034B-00_EN.indd Sec3:13Installation_DD81-02034B-00_EN.indd Sec3:13 5/10/2016 10:56:03 AM5/10/2016 10:56:03 AM

14_ installing the dishwasher

STEP 7 PLACING THE DISHWASHER AND CONNECTING THE HOT

WATER SUPPLY LINE

1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height

of the cabinet opening from under the countertop to the ﬂ oor. (See Step 8, Leveling the

Dishwasher.)

2. Locate the hot water supply line and the power cable.

3. Place the dishwasher so that the power cable is in the right channel of the base of the

dishwasher. Use standard duct tape or cable ties to secure the electrical cable to their

adjacent channels in the base. This can prevent the electrical cable from being squeezed

when you push the the dishwasher into place.

4. Pull the drain hose through the hole in the sink cabinet side wall. Keep it free of kinks.

5. Make sure the hot water supply line is not twisted, and then connect the hot water supply

line to the elbow joint.

6. Slide the dishwasher carefully into the installation space. If possible, gently pull any excess

lengths of water supply line, drain hose, or power cable back as you move the dishwasher.

Get a second or third person to help you do this if necessary.

Do not place the dishwasher on the water supply line, drain hose, or power cable.

Also, make sure they are not folded or twisted.

CAUTION

Do not overtighten the 90˚ Fitting.

(Below 280 lb·in (31.6 N·m))

Doing so may damage the water inlet

valve and cause a water leak.

Hot Water Supply Line

Drain hose

Hot Water Supply Line

Elbow( 3/4" (9.5 mm))

Inlet valve

installing the dishwasher

CAUTION

Installation_DD81-02034B-00_EN.indd Sec3:14Installation_DD81-02034B-00_EN.indd Sec3:14 5/10/2016 10:56:03 AM5/10/2016 10:56:03 AM

installing the dishwasher _15

02 INSTALLING THE DISHWASHER

STEP 8 LEVELING THE DISHWASHER

1. Open the door and place the level against the top of the

tub on the inside and check if the the dishwasher is level.

If it is not level, rotate the leveling legs at the bottom front

of the dishwasher until the dishwasher is level.

See the ﬁ rst note below for instructions on adusting the

height of the front legs.

2. Use the level to check if the dishwasher is level front to

back, as shown in the ﬁ gure to the right.

If the dishwasher is not level front to back, adjust the

height of the rear leg until the dishwasher is level.

See the second note below for instructions on adusting

the the rear leg.

3. Open the door of the dishwasher and

check if both the tub and door clearances

are correct.

If not, rotate the leveling legs on the

bottom front of the dishwasher.

You can also check this by placing a level

against an inside front vertical surface of

the tub.

If the leveling legs are rotated to the right (counter

clockwise), they are loosened and the front of the

dishwasher is raised. If they are rotated to the left

(clockwise), they are tightened and the front of the

dishwasher is lowered.

To adjust the height of a rear leg, turn the Hexbolt (at

the front of the base) to the left to raise the back of the

dishwasher using the proper tool (Hex L-wrench or

similar tool).

Before you move the dishwasher for installation, make sure to adjust the height of the

legs so the legs are as short as possible. This prevents the legs from breaking. Level the

dishwasher by adjusting the height of the legs after you have the dishwasher in place.

The dishwasher can leak if it’s tilted by more than 1 degree.

CAUTION

Installation_DD81-02034B-00_EN.indd Sec3:15Installation_DD81-02034B-00_EN.indd Sec3:15 5/10/2016 10:56:04 AM5/10/2016 10:56:04 AM

16_ installing the dishwasher

STEP 9 SECURING THE DISHWASHER

You must ﬁ x the dishwasher to the countertop or cabinet side walls for additional stability and safety.

1. If the countertop is made of wood or the material will not be damaged by drilling, follow

the instructions in 2-1 below.

If the countertop is made of granite, marble, or any other material that can be damaged

by drilling, follow the instructions in 2-2 below.

2-1. If the installation brackets on the front of the dishwasher extend cut them down using a

nipper as shown in Figure 8 on the next page.

Put a large towel into the bottom of the dishwasher to prevent wood shavings or a

dropped screw from falling into the dishwasher.

Carefully drill screw holes into the counter top bottom by passing the drill bit through a

screw hole in each bracket, and then drilling into the counter top bottom beneath.

Make sure the hole you drill is smaller than the diameter of the screw.

Insert the provided screws into the brackets, and then tighten to secure the dishwasher to

the counter top.

2-2. Put a large towel into the bottom of the dishwasher to prevent wood shavings or a

dropped screw from falling into the dishwasher. Remove the tub spacer caps with the tip

of a screwdriver. The caps are just inside the tub near the top of the tub on both sides

(Figure 9 on the next page).

Drill a hole into the sides of the kitchen cabinet on both sides by carefully passing a drill

bit through the screw holes exposed by the removal of the spacer caps, and then drilling

into the cabinet side beneath.

Make sure the hole you drill is smaller than the diameter of the screw.

Also make sure the drill bit does not strike the sides of the spacer cap holes. Insert the

provided screws into the holes, and then tighten to secure the dishwasher to the cabinet.

Make sure the tub is not distorted by pressure from the screws.

If the tub is distorted, loosen the screws a little.

Replace the tub spacer caps.

• The screws or tub spacer cap may fall into the dishwasher while you are working

with the door open. Cover the interior of the dishwasher with a towel to prevent

any screws from falling into the dishwasher. If any foreign items such as a screw

get into the dishwasher, it may cause noise, an abnormal operation, damage, or a

malfunction.

• Use a magnetic screwdriver to help prevent screws from falling into the dishwasher.

• If a foreign item such as a screw gets into the dishwasher and you are unable to

remove it, the dishwasher needs to be disassembled. Contact a qualiﬁ ed service

technician for this.

installing the dishwasher

Installation_DD81-02034B-00_EN.indd Sec3:16Installation_DD81-02034B-00_EN.indd Sec3:16 5/10/2016 10:56:04 AM5/10/2016 10:56:04 AM

installing the dishwasher _17

02 INSTALLING THE DISHWASHER

STEP 10 CONNECTING THE DRAIN HOSE

1. Check the parts on the sink to which the drain hose will be connected.

2. There are several ways to insert the drain hose into the drain hose connector of the sink,

as shown in the following ﬁ gures. You must connect the drain hose in accordance with the

water pipe installation regulations in your region.

Case 1. Without disposal

Without disposal With an air gap/without disposal Without an air gap

Tub spacer cap

Screw to side wall

Screw to countertop

Air gap

Drain hose

Hose clamp

Installation_DD81-02034B-00_EN.indd Sec3:17Installation_DD81-02034B-00_EN.indd Sec3:17 5/10/2016 10:56:04 AM5/10/2016 10:56:04 AM

18_ installing the dishwasher

installing the dishwasher

Case 2. With disposal

With disposal Disposal with an air gap Without an air gap

3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end

ﬁ ts onto the sink connector (1" or 5/8" - as shown in Figure 11 below). If the end of the drain

hose does not ﬁ t onto the drain hose connector of the sink, use an adaptor purchasable at a

plumbing/hardware supply store.

4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink

connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp.

Note : You must use a hose clamp. Failure to do so may cause water leakage.

5. If there is no air gap, make sure to hang. the middle of the drain hose well above the sink

cabinet base to prevent backﬂ ow (see Figure 13 on the next page).

When drilling a hole for the drain hose on the cabinet wall, take caution not to damage the

drain hose by sharp edges of the hole. On wooden walls, use sand paper to soften the edges.

On metal walls, use insulation tape or duct tape to cover the sharp edges around the hole.

7. Take caution not the damage the drain hose when installing the dishwasher on the ﬂ oor, wall,

or cabinet.

To prevent leaks or drainage problems, make sure the drain hose is not damaged, kinked,

or twisted.

8. Do not cut the wrinkled area of the drain hose to ﬁ t the size. When arranging the drain hose,

take caution not to contact on sharp edges of the cabinet or under-sink.

• Be careful when cutting o the end of the drain hose as there is a risk of injury. Clean

around the sink’s drain connection so that it does not damage the hose. Check for

any foreign items in the drain hose and remove them.

• When arranging the drain hose, make sure the drain hose is not cut, torn, or broken

by any sharp edges of the ﬂ oor, the product itself, or the cabinet. A damaged drain

hose causes a leak.

CAUTION

Air gap

Hose clamp

Drain hose

Hose clamp

Installation_DD81-02034B-00_EN.indd Sec3:18Installation_DD81-02034B-00_EN.indd Sec3:18 5/10/2016 10:56:05 AM5/10/2016 10:56:05 AM

installing the dishwasher _19

02 INSTALLING THE DISHWASHER

Sink

Dishwasher

Drain hose

Min. 30 in.

(762 mm)

Min. 20 in.

(508 mm)

If necessary, cut o the

dotted line of the drain hose

to ﬁ t the size.

1 in.

(25 mm)

/8 in.

(16 mm)

Secure the drain hose to the sink wall using

cable ties or other fastening materials.

Otherwise, the drain hose may bend at the

end, causing a drainage problem or excessive

supply of water.

Installation_DD81-02034B-00_EN.indd Sec3:19Installation_DD81-02034B-00_EN.indd Sec3:19 5/10/2016 10:56:05 AM5/10/2016 10:56:05 AM

20_ installing the dishwasher

installing the dishwasher

STEP 11 WIRING CONNECTIONS

1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is o .

2. In the junction box located at the front bottom right of the dishwasher, ﬁ nd the three power

wires from the dishwasher including the grounding line.

3. Pass the power cable through the strain relief, and then into the junction box (Figure 14).

4. Connect the black wire of the dishwasher to the black wire of the power cable by insertng

both into a wire nut and then rotating the wire connector as shown in Figure 15.

Connect the white wire to the white wire and the green to the green in the same manner.

5. Recheck each wire to ensure it is connected correctly and securely.

Each colored wire should be connected to the corresponding wire of the same color.

White should be connected to white, black to black, and green to green.

6. Replace the junction box cover on the dishwasher.

Recheck each wire to ensure it is connected correctly and securely.

Each colored wire should be connected to the corresponding wire of the same color.

WARNING

Electrical Shock Hazard

To avoid electrical shock, do not work on an energized

circuit. Doing so could result in serious injury or death.

Only qualiﬁ ed electricians should perform electrical

work. Do not attempt any work on the dishwasher

electric supply circuit until you are certain the circuit is

de-energized.

WARNING

Fire Hazard

To avoid a ﬁ re hazard, make sure electrical work is

properly installed. Only qualiﬁ ed electricians should

perform electrical work.

Black to black

White to white

Green to green

(Ground to ground)

Power cable

Junction box

Strain relief

Installation_DD81-02034B-00_EN.indd Sec3:20Installation_DD81-02034B-00_EN.indd Sec3:20 5/10/2016 10:56:06 AM5/10/2016 10:56:06 AM

La page charge ...

Samsung DW80K5050 Series Guide d'installation

Marque: Samsung

Modèle: DW80K5050 Series

Taper: Guide d'installation

Ce manuel convient également à

DW80K7050 Series

Télécharger le PDF

rapport

dans d''autres langues

English: Samsung DW80K5050 Series Installation guide

Samsung DW80K5050 Series Guide d'installation

Ce manuel convient également à

Samsung DW80K5050 Series Guide d'installation

dans d''autres langues

Documents connexes

Autres documents