Marvel MP36BF2LP Guide d'installation

Marque: Marvel

Modèle: MP36BF2LP

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Installation

Instructions

Built-In

Bottom-Freezer

Refrigerator

MP36BF2

Table of Contents

Warnings and Important Information _____________________________________________3

Professional Bottom-Freezer

Dimensions ______________________________________________________________ 6

Speciﬁ cations _____________________________________________________________ 7

Cutout Dimensions _________________________________________________________8

Anti-Tip Dimensions (36”) __________________________________________________ 9

Cabinet Information (Professional) _____________________________________________ 10

Cabinet Information (Professional with ﬂ ush mount trim) __________________________ 11

Custom Side Panel Dimensions (Professional) ___________________________________ 12

Custom Side Panel Dimensions (Professional with ﬂ ush mount trim) ________________ 13

General Information __________________________________________________________ 14

Unpacking & Moving _________________________________________________________ 16

Flush Mount Side Trim Installation _____________________________________________ 17

Installation __________________________________________________________________ 17

Hinge Adjustment ________________________________________________________ 18

Kickplate Installation ______________________________________________________ 21

Door Stop Adjustment ____________________________________________________ 21

System Speciﬁ cations and Data ____________________________________________ 22

Final Installation__________________________________________________________ 23

Performance Checklist ________________________________________________________ 24

Control Panels _______________________________________________________________ 25

Service & Registration ________________________________________________________ 26

IMPORTANT – Please Read and Follow!

• Make sure that incoming voltage is the

same as unit rating. An electric rating

plate specifying voltage, frequency,

wattage, amperage, and phase is attached

to the product.

• To reduce the risk of ﬁ re, electrical shock,

or injury to persons, installation work and

electrical wiring must be done by a

qualiﬁ ed technician in accordance with all

applicable codes and standards, including

ﬁ re-rated construction.

• The installer should leave these

instructions with the consumer who should

retain them for local inspector’s use and

for future reference.

DANGER

WARNING

You will be killed or seriously injured if

you don't follow instructions.

You can be killed or seriously injured if

you don't follow instructions.

All safety messages will identify the

hazard, tell you how to reduce the chance

of injury, and tell you what can happen if

the instructions are not followed.

Your safety and the safety of others is

very important.

We have provided many important safety

messages in this manual and on your

appliance. ALWAYS read and obey all

safety messages.

This is the safety alert symbol. This

symbol alerts you to hazards that

can kill or hurt you and others.

All safety messages will be preceded

by the safety alert symbol and the word

“DANGER” or “WARNING.” These

words mean:

IMPORTANT – Please Read and Follow!

A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local

laws, or local ordinances.

• The required use of a GFI is normally related to the location of a receptacle with respect to

any signiﬁ cant sources of water or moisture.

• AGA Marvel will NOT warranty any problems resulting from GFI outlets which are not

installed properly or do not meet the requirements below.

If the use of a GFI is required, it should be:

• Of the receptacle type (breaker type or portable type NOT recommended)

• Used with permanent wiring only (temporary or portable wiring NOT recommended)

• On a dedicated circuit (no other receptacles, switches or loads in the circuit)

• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT

recommended)

• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)

• In good condition and free from any loose-ﬁ tting gaskets (if applicable in outdoor situations)

• Protected from moisture (water, steam, high humidity) as much as reasonably possible

WARNING

TIP OVER HAZARD

Appliance is top heavy

and tips easily when not

completely installed. Keep

doors closed until appliance

is completely installed and secured per

installation instructions.

Use two or more people to move and

install appliance. Failure to do so can

result in death or serious injury.

WARNING

ELECTRICAL SHOCK

HAZARD

Disconnect power or turn

power disconnect switch to

OFF position before removing top grille.

Failure to do so can result in death or

electrical shock.

IMPORTANT – Please Read and Follow!

Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent

tipping. Use cardboard shipping material or plywood under unit until it is installed in the

operating position to protect ﬂ oor surface.

It is your responsibility to:

• comply with installation speciﬁ cations and dimensions.

• properly install unit.

• remove any moldings or decorative panels that prevent the unit from being serviced.

• make sure that you have these materials (not provided with your unit), which are necessary

for proper installation:

• 1/4” (6 mm) copper tubing with shutoff valve

• 6– #8 x 3” (7.6 cm) wood screws (longer screws may be required)

• 1– Saddle valve (do not use self-piercing feature of the valve)

• assure that ﬂ oor will support unit, door panels and contents (approximately

1200 pounds [540 kg]).

• provide a properly grounded electrical outlet.

• assure that location will permit appliance doors to open 90º minimum.

Dimensions (Bottom-Freezer)

36” Bottom-Freezer

24”

(61.0 cm)

35”

(88.9 cm)

52”

(132.1 cm

)

23–1/16”

(58.5 cm

)

3–19/32”

(9.1 cm)

36”

(91.5 cm)

36”

(91.5 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

84–1/16”

(213.5 cm)

max.

0–3/4”

(52.7 cm)

22–3/16”

(56.4 cm)

1–1/2”

(3.8 cm)

26”

(66.0 cm)

24”

(61.0 cm)

35”

(88.9 cm)

52”

(132.1 cm

)

23–1/16”

(58.5 cm

)

3–19/32”

(9.1 cm)

36”

(91.5 cm)

36”

(91.5 cm)

9–5/32”

(23.3 cm)

82–3/4”

(210.2 cm)

min.

84–1/16”

(213.5 cm)

max.

0–3/4”

(52.7 cm)

23–3/8”

(59.4 cm)

1–1/2”

(3.8 cm)

26”

(66.0 cm)

Note: Flush Mount Trim (PBIRFTKSS) purchased separately.

36” Bottom-Freezer with

Flush Mount Trim

Speciﬁ cations (Bottom-Freezer)

36” Bottom Freezer

Description MP36BF2

Overall width 36” (91.5 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 22-3/16” (56.4 cm)

To front of top grille: 24” (61.0 cm)

To front of handle endcap: 26” (66.0 cm)

Cutout width 35-5/8” (90.5 cm) min. to 35-3/4” (90.8 cm) max.

Cutout height

82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Cutout depth 24” (61.0 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi;

maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

15.3 cu. ft. (434 liters)

5.1 cu. ft. (145 liters)

20.4 cu. ft. (579 liters)

Approximate shipping weight 565 lbs. (254.3 kg)

36” Bottom Freezer with Flush Mount Trim

Description MP36BF2 w/Flush Mount

Overall width 36” (91.5 cm)

Overall height (from bottom) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max.

Overall depth from rear To front edge of side trim: 23-3/8” (59.4 cm)

To front of top grille: 24” (61.0 cm)

To front of handle endcap: 26” (66.0 cm)

Cutout width 36” (91.5 cm)

Cutout height

82-7/8” (210.5 cm) min. to 84-1/16” (213.5 cm) max.

Cutout depth 24” (61.0 cm) min.

Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product

Maximum amp usage 9.9 amps

Inlet water requirements 1/4” copper tubing inlet waterline; minimum 20 psi;

maximum 120 psi

Overall interior dimensions

Refrigerator

Freezer

Total capacity

15.3 cu. ft. (434 liters)

5.1 cu. ft. (145 liters)

20.4 cu. ft. (579 liters)

Approximate shipping weight 565 lbs. (254.3 kg)

Cutout Dimensions (Bottom-Freezer)

9”

(22.9 cm)

73-3/8”

(186.4 cm)

82–7/8”

(210.5 cm) min.

anti-tip board &

opening height

84–1/16”

(213.5 cm) max.

anti-tip board &

opening height

35–5/8”

(90.5 cm) min.

35–3/4”

(90.8 cm) max.

36”

(91.5 cm)

PFlush Mount only

24”

(61.0 cm)

Electric Outlet Location

Water Line Entry Area

6–3/4”

(17.1 cm)

7–5/8”

(19.4 cm)

3”

(7.6 cm)

5/8”

(1.6 cm)

5/8”

(1.6 cm)

10–1/2”

(26.7 cm)

5/8”

(1.6 cm)

10–3/4”

(27.3 cm)

1”

(2.5 cm)

3–5/8”

(9.2 cm)

Optional floor

water line entry

35–5/8”

(90.5 cm)

36”

(91.5 cm)

Flush Mount only

See Anti-Tip board installation

6”

(15.2 cm)

9”

(22.9 cm)

36” Bottom-Freezer

Anti-Tip Dimensions (Bottom-Freezer)

36” Bottom-Freezer

Two 2”x 4” Mounting Boards

3” (7.6 cm) x 3-1/2” (8.9 cm)

NOTE: If unit is installed deeper than

24” (61.0 cm), then shim behind the mounting

boards by the difference.

NOTE: If unit is installed deeper than

24” (61.0 cm), then shim behind the mounting

boar

ds by the difference.

One 2”x 4” Mounting Boar

3” (7.6 cm) x 3-1/2” (8.9 cm)

Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.

NOTE: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

Flush Mount Anti-Tip Location

79–3/8”

(201.6 cm) min.

to bottom of

anti-tip board

80–1/2”

(204.6 cm) max.

to bottom of

anti-tip board

29–1/2”

(74.9 cm)

3–1/2”

(8.9 cm)

3”

(7.6 cm)

29–1/2”

(74.9 cm)

3–1/2”

(8.9 cm)

1.5”

(3.8 cm)

Cabinet Information (Professional)

Door

Wall

1–13/16”

(4.6 cm)

Space if 24”

standard

cabinet

depth is

used

3/4”

(1.9 cm)

Full End

Panel

24”

(61.0 cm)

Standard

Cabinet

Depth

1–3/4”

(4.4 cm) Offset

5/16”

(0.8 cm)

Professional models ﬁ t “semi-ﬂ ush” in standard 24” (61.0 cm) deep cabinet openings. The door

face protrudes 1-3/4” (4.4 cm) from the cabinet face. The handle protrudes an additional

2-1/2” (6.4 cm) into the room.

Top View

1–13/16”

(4.6 cm)

Space if 24”

standard

cabinet

depth is

used

Door

24”

(61.0 cm)

Standard

Cabinet

Depth

Wall

3/4”

(1.9 cm)

Full End

Panel

1–3/4”

(4.4 cm) Offset

Countertop

Overhang

Cabinet Information (Professional with Flush Mount Trim)

Top View

Door

24”

(61.0 cm)

Standard

Cabinet

Depth

25”

(63.5 cm)

Countertop

Depth

Wall

3/4”

(1.9 cm)

Full End

Panel

Door

Wall

1”

(2.5 cm)

space if

25” (63.5 cm)

cabinet depth

is used

3/4”

(1.9 cm)

Full End

Panel

25”

(63.5 cm)

Flush

1”

(2.5 cm)

space if

25” (63.5 cm)

cabinet depth

is used

Flush

Professional models with ﬂ ush mount trim ﬁ t ﬂ ush in standard 24” (61.0 cm) deep cabinet

openings with no protrusion into the room except the handle protrudes 2-1/2” (6.4 cm) into the

room.

Custom Side Panel Dimensions

(Professional)

3/4”

(1.9 cm)

End panel

5/32”

(0.4 cm)

3/16”

(0.5 cm)

Back filler

panel

22-7/16”

(57.0 cm)

22-7/16”

(57.0 cm)

22-1/4”

(61.0 cm)

6”

(15.2 cm)

Optional kickplate

Notch, dimensions

determined by cabinets

82-7/8”

(210.5 cm) min.

84-1/16”

(213.5 cm) max.*

82-7/8”

(210.5 cm) min.

84-1/16”

(213.5 cm) max.*

6”

(15.2 cm)

22-1/4”

(61.0 cm)

* Depending on how high leveling feet are raised, and cabinet enclosure height.

Custom Side Panel Dimensions

( Professional with Flush Mount Trim)

* Depending on how high leveling feet are raised, and cabinet enclosure height.

3/4”

(1.9 cm)

End panel

1”

(2.5 cm)

1/4”

(0.6 cm)

Z-Bracket

21-3/4”

(55.2 cm)

21-3/4”

(55.2 cm)

24”

(61.0 cm)

Optional kickplate

Notch, dimensions

determined by cabinets

24”

(61.0 cm)

82-7/8”

(210.5 cm) min.

84-1/16”

(213.5 cm) max.*

82-7/8”

(210.5 cm) min.

84-1/16”

(213.5 cm) max.*

General Information

Area Requirements

Verify the following:

• Unit can ﬁ t into residence and can be

moved around corners and through

doorways.

• Floors can support unit’s weight plus

food weight (approximately 1200 pounds

[540 kg] per unit).

• Floors underneath refrigerator are level

with surrounding ﬁ nished ﬂ oor.

• Rear wall is solid and is able to support

two horizontally mounted 2 x 4s (included)

bolted to two wall studs. The 2 x 4 board

bolt heads must be ﬂ ush with 2 x 4 to

prevent obstruction.

• Remove anything attached to rear or side

walls that can obstruct unit installation.

• Cutout dimensions are accurate.

• Electrical outlet is in correct location.

• Water line is in correct location.

• DO NOT install a refrigeration unit near

a heat source, nor in a location where the

surrounding temperature will fall below

60º F (16º C).

Electrical Requirements

It is the customer’s responsibility to:

• Contact a qualiﬁ ed electrical installer.

• Assure that the electrical installation is

adequate and in conformance with

the National Electrical Code, ANSI/

NFPA 70-latest edition or Canadian

Electrical Code C22.1-1998 and C22.2

No. 0-M91 (or latest edition), and all local

codes and ordinances.

A 115 volt, 60-Hz, 15 amp, fused, electrical

supply is required. It is required that a

separate circuit serving only this appliance

be provided. This appliance is equipped

with a power supply cord having a 3-prong

grounding plug. To minimize possible

shock hazard, the cord must be plugged

into a mating 3-prong, grounding-type wall

receptacle. DO NOT use an extension cord.

If codes permit a separate grounding wire

to be used, it is recommended that a

qualiﬁ ed electrician determine that the

grounding path is adequate.

DO NOT ground to a gas line. Check with a

qualiﬁ ed electrician if you are not sure if the

appliance is properly grounded. DO NOT

have a fuse in the neutral or grounding

circuit.

Anti-Tip Requirements

The anti-tip boards should be fastened

into position prior to moving the unit into

the opening.

Note: Additional mounting boards may

be required if the unit does not touch

the back wall of the enclosure. To prevent

unit from tipping forward, it must be secured

in place with a solid sofﬁ t or wood block.

General Information

Water Supply Requirements

Use only 1/4” (6 mm) copper tubing for

water line. DO NOT install copper tubing

in area where temperatures drop below

35º F (1.7º C). Before attaching copper

tubing to the unit, ﬂ ush at least 2 quarts

(1.9 L) of water through the copper tubing

and into a bucket to remove any particles

in the water line.

• AGA Marvel is not responsible

for property damage due to improper

installation or water connection.

• Connect 1/4” (6 mm) ﬂ exible copper

tubing to household plumbing in

compliance with local codes and

ordinances.

• Length of copper tubing must reach from

water supply connection to the unit

connection with an additional length to

facilitate moving the unit out of enclosure

for cleaning or service. Tubing should be

soft instead of rigid and ends should be

free of burrs.

• Copper tubing route must be above 35º F

(1.7º C) to prevent water line from freezing.

• DO NOT use plastic water lines from

the household plumbing to the water

inlet valve connection on the

refrigeration unit.

• DO NOT use the self-piercing feature of

a saddle valve. The hole made by the

piercing lance is too small for the water

ﬂ ow rate required by the ice maker.

• If saddle valve is not used, place a

separate shut-off valve in an easily

accessible location between water supply

and the unit. DO NOT install shut-off valve

behind the unit.

• The installation of units with a reverse

osmosis system is acceptable as

long as the water pressure remains

within the allowable PSI as stated

below. It is important to note that with

many reverse osmosis systems, the

pressure starts off high, but then it

decreases as the water level of the reverse

osmosis storage area drops. This must

be considered when checking the water

pressure coming into the unit.

• Connect a vertical or horizontal 1/2”

(1.3 cm) to 1-1/4” (3.2 cm) COLD water

line near water area.

• Run water line through the ﬂ oor, back,

or side wall. Tubing should lay ﬂ at on ﬂ oor

underneath the unit. Clamp tubing to wall

or ﬂ oor.

• Water pressure must be greater than

20 psi and less than 120 psi on non-

dispensers and greater than 35 psi and

less than 120 psi on dispensers.

WARNING

To avoid serious illness or death, DO NOT use

unit where water is microbiologically unsafe

or of unknown quality, without adequate

disinfection before or after the system.

Systems certiﬁ ed for cyst reduction may be

used on disinfected water that may contain

ﬁ lterable cysts. The contaminants or other

substances removed or reduced by this water

treatment system are not necessarily

in your water.

CAUTION

Be sure to have a replacement cartridge

available when ﬁ lter change is required.

• If water ﬁ ltration system has been allowed to

freeze, replace ﬁ lter cartridge.

• If system has not been used in several

months, and water has an unpleasant

taste or odor, ﬂ ush system by dispensing

2-3 glasses of water. If unpleasant taste or

odor persists, change ﬁ lter cartridge.

General Information

Area Requirements

• Most of the unit’s weight is at the top.

Extra care is needed when moving the unit

to prevent tipping.

• DO NOT remove protective ﬁ lm until unit

is in operating position.

• All four leveling legs must contact the ﬂ oor

to support and stabilize the full weight.

• DO NOT drop unit.

• Remove exterior shipping materials prior

to moving unit into home, except door

latching device.

• Use two or more people to move and

install unit. Failure to follow this instruction

can result in back or other injury.

• To avoid personal injury, wear gloves when

performing any installation procedure and

wear eye protection when cutting metal

straps.

Tip Over Hazard

Appliance is top heavy and tips easily when

not completely installed. Keep doors closed

until appliance is completely installed and

secured per installation instructions. Use

two or more people to move and install

appliance. Failure to do so can result in

death or serious injury.

Unpacking Unit

1. Remove top and bottom strap.

2. Remove top cap.

3. Cut carton rear approximately 1/4”

(0.6 cm) to 1” (2.5 cm) from right corner

with a utility knife extended 1/4” (0.6 cm).

4. Remove carton and exterior packaging.

Save cardboard shipping material to

protect ﬂ oor surface when installing unit.

Remove anti-tip board and kickplate

from rear of unit.

Moving Unit

Remove shipping brackets from skid by removing four

bolts (two on each side) with a 1/2” (1.3 cm) deep-well

socket wench and a pair of pliers. Note: Tilting unit is

not required to remove shipping brackets.

Slip appliance dolly between unit and skid.

Remove unit from skid. Note: Use excess packaging

to protect decorative trim; also, verify that

leveling legs are up (0” adjustment).

Note: If the unit is to be installed ﬂ ush with

the cabinets, the ﬂ ush mount side trim must

be installed ﬁ rst. If not, skip to “Installation”.

Step 1 - Locate the necessary parts: Two (2)

ﬂ ush mount trim pieces and a hardware kit

with twenty-two (22) screws.

Step 2 - Remove the side trim on the

refrigerator and discard the trim and screws.

Step 3 - Align the top of the ﬂ ush mount

side trim with the top of the unit's machine

compartment. Using the screws included in

the hardware kit, attach the side trim to the

unit, only using the holes visible through

the side trim. Note: DO NOT use the screw

holes in the machine compartment.

Place unit in front of cutout. Pull the center grille louver up at an angle and pull out.

Using an 8” (20.3 cm) magnetic nut driver, remove

the two 1/4” (0.6 cm) screws.

Remove grille assembly.

Installation

Flush Mount Side Trim Installation

(Sold Separately)

Wall

2 x 4

Refrigerator

Front of unit

1 3

Replace unit top. Replace four side screws. Attach one 2 x 4 to wall stud (refer to dimensions page

for exact location).

Loosen the four hinge screws. Adjust door.

Retighten four hinge screws.

Remove four side screws and remove unit top.

Wall

2 x 4

Refrigerator

If needed, depending on cabinet and depth,

attach second 2 x 4 to ﬁ rst 2 x 4.

Plug in power cord to verify operation.

Note: Make sure power switch is in the “On” Position.

Hinge Adjustment

Pull supply tubing forward under unit.

Note: DO NOT use plastic water lines.

Flush water line by running two quarts of water

into a bucket. Turn water off.

Connect supply tube to water valve using

a 1/2” wrench. Note: DO NOT overtighten.

Turn on water supply and check for leaks.

10b

Place unit within 3” (7.6 cm) of being ﬂ ush with cabinets. Note: To

avoid cabinet damage, place cardboard between cabinets and unit.

When moving unit, DO NOT crimp, kink or crush water supply line.

Carefully move unit until semi ﬂ ush with cabinet

(depending on unit).

3”

10a

Hinge Adjustment (cont.)

Reinstall cabinet trim and screws.

Wall

2 x 4

Refrigerator

Screw

Lift unit off rollers to desired height and level unit using

a 5/16” head wrench. NOTE: DO NOT use an electric

device. Overtightening can cause damage.

Reinstall handle side door trim

and door trim screws.

Hinge Adjustment (cont.)

La page charge ...

Marvel MP36BF2LP Guide d'installation

Marque: Marvel

Modèle: MP36BF2LP

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MP36BF2LP Installation guide
español: Marvel MP36BF2LP Guía de instalación

Marvel MP36BF2LP Guide d'installation

Ce manuel convient également à

Marvel MP36BF2LP Guide d'installation

dans d''autres langues

Documents connexes

Autres documents