FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
1
INTRODUCTION 2
CREATING A HARDCOVER BOOK 3
CUSTOMIZING OPTIONS 6
ADDING HEADBANDS 7
ABOUT FOILFAST® TITLE SHEETS 8
FOILFAST® TITLE SHEET TIPS 9
SPINE TITLING 10
TROUBLESHOOTING 11
GLOSSARY 12
COPYRIGHT & WARRANTY 14
ÍNDICE 15
TABLE DES MATIÈRES 29
CONTENTS
ÍNDICE
TABLE DES MATIÈRES
This manual was bound
with a Fastback® binder
PN: L5648
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
2
INTRODUCTION
The Fastback Hardcover™ Binding System
is a revolutionary new system for creating
professional hard cover books on-demand.
There is no set-up and you can make a book
within a minute. The key to the system is the
Fastback Hardcover Guide. The Guide performs
the following functions:
• It specifies the correct cover spine width.
• It positions and assists the assembly of
your printed pages into the hard cover.
• It positions and assists the application of
Foilfast Title Sheets.
Whether you are looking for a cost-effective
way to produce books for resale, or you want
to create memory books for your children and
friends, the Fastback Hardcover product line is
the perfect solution.
Spacer
Spacer Storage Slot
Rear Paper Stop
Rear Cover Stop
Spacer
Instruction Card
Base
Base Notch
Clamp Lever
Side Paper Stop
Side Cover Stop
Book Thickness Indicator
Slider
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
3
CREATING A HARDCOVER BOOK
Fastback Hardcovers™ are currently available in
many popular sizes, from 8” to A4. You may
select from Suede and premium Composition
covers as well as Library and Art cloths, with a
great choice of colors and materials. Check with
your dealer for more information.
Before binding your pages, place folded
Fastback® endleaves at the front and the back of
your printed pages (Fig. 1). The folds should be
at the spine side of your pages.
Insert this book block (with the endleaves folded
end down) into the binding cavity of the Fastback
binder (Fig. 2) Bind the book block using a
Hardcover Linen strip. This strip was specially
designed for binding hard cover books. They are
more flexible than other strips so there is less
stiffness when turning the pages, plus they give an
enhanced look to your book.
For a traditional finishing touch, add headbands to
the top and bottom of the spine after binding the
book block. Refer to page 7.
The correct cover spine width is determined by
the thickness of the bound book block. After your
book block has cooled, place it between the right
purple cover stop and the slider handle at the
front right corner of the Guide. Slide the handle
against the book block (Fig. 3). The horizontal line
points to the letter size of which cover width
to use. Covers are available in six sizes, A-F.
When using wider covers (sizes C to F), it is
necessary to use the plastic spacers provided with
the Guide. Without these spacers, the book block
may skew, resulting in an imperfect bind.
The spacers are stored in slots at the rear left
corner of the Guide. We have provided three
spacers, although you only use two at a time.
The third one is an spare. To use the spacers,
push them into the lettered slots on the cover
stops as indicated by corresponding width (Fig. 4).
For example, for an E width book, the spacers
should be inserted in the slots marked ‘E’.
F I G U R E 2
F I G U R E 3
F I G U R E 4
F I G U R E 1
E
H
G
F
E
D
C
u
FOLDED
ENDLEAVES
PRINTED
PAGES
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
4
Slide the Instruction Card to the upper right
corner of the base (Fig. 5). The white tab fits
under the clamp and the front left angle fits
behind the base notch. For thicker covers,
this card should be removed.
Place your Fastback Hardcover™ on the Guide
with the release papers facing up, (the back
cover of the book should be to the right).
Slide the cover to the right rear corner of the
base (Fig.6–Step 1). The right and top edges of
the cover should contact the right and rear steps
of the base, with the cover under
the paper
stops (step 1 arrows). Flip the lever to the right
to clamp the cover in place (step 2 arrows).
Remove the strip of narrow release paper to the
right of the spine (Fig. 7).
With the front of your book block facing up,
push the page edges against the top and side
green paper stops (and spacers if required —
see page 3, Fig. 4). With the page edges held
against the edges of the paper stops and spacers,
push the spine edge of the book block down
firmly onto the exposed narrow adhesive strip
(Fig. 8).
CREATING A HARDCOVER BOOK
(cont.)
F I G U R E 7
F I G U R E 8
F I G U R E 5
F I G U R E 6
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
5
CREATING A HARDCOVER BOOK
(cont.)
With the spine edge attached, carefully rotate
the book block to the left. Remove the wide
release paper on the right side (Fig. 9). Roll the
book block back to the right onto the exposed
adhesive, securing the back endleaf.
Remove both the narrow and wide release
papers on the left hand side of the cover (Fig. 10).
Lift the front cover over the top of the book
block (Fig. 11). The cover edges must contact the
rear and side purple cover stops (Fig. 11 detail
arrow). Then press the cover down onto the
book block.
Flip the lever up to release your book.
Open front and back covers to smooth down the
inside endleaves (Fig. 12).
Your Fastback® Hardcover™ book is done!
F I G U R E 10
F I G U R E 11
F I G U R E 12
F I G U R E 9
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
6
CUSTOMIZING OPTIONS
To get the best results, take advantage of the
customizing features that are offered as part of
the Fastback
®
Hardcover™ product line.
Headbands
Headbands are narrow strips of cloth fastened
between the book block and the spine at the
top and bottom of a book. Although they were
once an integral part of the binding process,
most headbands today are used as attractive
decorative touches. Fastback Headbands
come in a variety of solid and checkered color
combinations (Fig. 13).
Foilfast® Title Sheets
& Spine Titling
Using Powis Parker’s Foilfast® printer, you can
title and decorate your covers with up to seven
colors of foil (Fig 14). Foilfast Title Sheets are
made of the same materials as the Fastback
Hardcovers, so you are ensured of a perfect
match. They may also be used to create spine
titles for you books (Fig. 15).
Traditional Techniques
Fastback Hardcovers are real hard cover cases.
They can be foil stamped, or embossed the
same as any traditional cover. Contact your
dealer for suggestions.
Headbands
Spine Titling
F I G U R E 13
F I G U R E 15
Foilfast®Title Sheets
F I G U R E 14
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
7
Peel the release paper backward exposing the
adhesive backing (Fig. 16).
Align the edge of the headband with the spine-
edge of the book block (Fig. 17).
Cut the headband strip to the same width as the
book block (Fig. 18).
ADDING HEADBANDS
F I G U R E 16
F I G U R E 17
F I G U R E 18
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
8
ABOUT FOILFAST® TITLE SHEETS
Foilfast® Title Sheets (FTS) are adhesive sheets
that match the Suede and Comp covers.
They are designed to work with the Foilfast®
printer to let you add printing to your covers in
seven colors of foil.
Insert the Foilfast® Title Sheet (FTS) into the
Foilfast printer so that the narrow release paper
is on the left side and facing away from you
(Fig 19).
CAUTION: Failure to insert the sheet in
the prescribed manner can result in printing
problems or machine damage.
Compose your design with any software.
When you are finished choose File>Print.
Click on the “Properties” button in the Print
window to open the Properties dialog box.
Choose the “Upside Down” option (Fig. 20).
Put your cover in the Fastback Hardcover Guide
with the exterior of the hard cover face up.
Make sure that the front cover is pushed all
the way into the corners of the Guide recess,
beneath
the green stops (Fig. 21—step 1
arrows).
Lock the cover in place by depressing the lever
to the right (Fig 21—step 2 arrow).
Remove the narrow release paper from the FTS.
Align the top and right sides of the FTS against
the edge
of the green paper stops (Fig. 22
detail). Then, press the exposed adhesive area
onto the cover.
Gently lift the right end of the FTS and remove
the large release paper (Fig. 23). Lay down the
FTS onto your cover. Smooth down the FTS to
complete your custom printed cover.
1
2
F I G U R E 19
F I G U R E 20
F I G U R E 23
F I G U R E 22
F I G U R E 21
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
9
Design Considerations
Foilfast®Title Sheets are slightly smaller than their
corresponding covers. For instance, the FTS for
the letter-size Fastback® Hardcover™ is 8-1/8”
rather than 8-1/2” wide. Artwork that you want
to center on the book covers should have its
center 4” from the left edge of the sheet.
Print Quality Considerations
Using the multiple-color ink setting on artwork
that appears in only one color sometimes
produces better results. Using the Clear Cover
setting also produces sharper results with certain
types of artwork.
Some colors, most notably white, will not print
on the suede material unless you use Foil Primer
undercoat.
The Clear Cover setting produces an attractive
and unique effect when gold foil is used on the
suede material.
Image files that print correctly in one format may
appear bitmapped when printed in a different
format, even though nothing other than the file
format is changed. This is also true with certain
programs. A PDF file that prints correctly in
Adobe Illustrator, for instance, may appear
bitmapped when printed with Adobe Acrobat.
TIPS (FOILFAST TITLE SHEET)
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
10
Spine titling is a desirable addition to any bound
document—the titles look professional and make
documents easier to identify when they are lined
up on a bookshelf.
It is an easy process to create your own
spine titles. We have created Microsoft Word
templates for book widths A through F.
You can download the templates from our
website at www.powis.com/dlrpowis/frontpages/
frontpage_nov2103/dlrtopnews2.asp. Small dots
or periods placed at the trim points of the spines
make it easier to trim the spines from the sheet.
Create your own spines using the
following guidelines:
Book Size Spine Width
A .375”
B .500”
C .750”
D 1.000”
E 1.250”
F 1.500”
SPINE TITLING
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
11
TROUBLESHOOTING
Tighting the Clamp Assembly
In case the purple cover stops become loose they
can be easily retightened using the following method.
Insert a standard screwdriver into the small slot
under the hood of the cover stop, and gently turn
the screwdriver sideways. The hood will pop off
(Fig. 23).
Inside the cover stop, you will see two screws.
With a Phillips screwdriver tighten the screws
carefully (Fig. 24).
CAUTION: Over-tightening the screws may damage
the Guide. Do not apply more pressure than is
necessary.
H
G
F
E
D
C
B
A
F I G U R E 23
F I G U R E 24
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
12
GLOSSARY
Like most professions, case binding (hard cover
binding) has its own terminology. Here is a
glossary of terms.
Book cloth
A specially treated woven cloth that is used to
make book covers. It is very rugged and durable.
Fastback Hardcovers come in two styles of cloth
covers: Library Cloth covers, which are designed
for durability in high-use environments, and
Art Cloth covers, which are designed for art and
photography books. The Library Cloth covers
feature more muted colors than Art Cloth
covers.
Book block
This is the interior section of the book,
comprised of the printed pages of the book and
the endleaves. It is important to note that the
size specification of a Hardcover is based on the
size the book block. A 6” × 9” Hardcover,
for instance, indicates that the book block is
6” × 9”, not that the cover is 6” × 9”.
Case
The term used in the binding industry for hard
covers.
Case Binding
This is the traditional method of making a
hard cover book.
Endleaf
A thick sheet of paper that is folded in half, and
used to attach the book block to the cover.
Two endleaves are used to make each book.
A BOOK BLOCK
B ENDLEAVES
C LINEN STRIP
D HEADBAND
E CASE (HARD COVER)
B
A
E
C
D
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
13
Headband
A narrow strip of cloth located where the book
block meets the spine at the top and bottom of
a book. Although it was once an integral part of
the binding process, most headbands today are
purely decorative. Headbands are usually either
checkered or solid colors.
Linen Strip
The linen strip is the latest Fastback binding strip.
It is a cloth strip designed specifically for use with
the Fastback Hardcover Binding System. It is a
very strong and especially flexible strip specially
designed for hard cover binding.
GLOSSARY (cont.)
FASTBACK HARDCOVER GUIDE USER’S MANUAL, REV.:C 06/09/05
14
COPYRIGHT INFORMATION
This document contains proprietary and confidential information of Powis Parker Incorporated (PPI).
No part of this document may be photocopied, reproduced in any form, or translated into another
language without prior written consent of PPI, except as allowed under the copyright laws.
Copyright© Powis Parker Incorporated 2004
All Rights Reserved.
WARRANTY
The information contained in this document is subject to change without notice.
PPI makes no warranty of any kind with respect to this information. PPI specifically disclaims the
implied warranty of merchantability and fitness for a particular purpose.
PPI shall not be liable for any direct, indirect, incidental, consequential, or other damage alleged in
connection with the furnishing or use of this information.
NOTICE
Changes are periodically made to this document. Revisions, changes, any technical inaccuracies,
and typographical errors will be corrected in any subsequent editions.
MANUAL DE INSTRUCCIONES DE LA GUÍA FASTBACK HARDCOVER, REV.:C 09/06/05
15
INTRODUCCIÓN 16
CREAR UN LIBRO DE TAPAS DURAS 17
OPCIONES DE PERSONALIZACIÓN 20
AÑADIR CABEZADAS 21
INFORMACIÓN SOBRE LAS HOJAS
DE TÍTULOS FOILFAST® 22
CONSEJOS DE LA HOJA DE
TÍTULOS FOILFAST® 23
TÍTULOS DE LOMOS 24
SOLUCIÓN DE PROBLEMAS 25
GLOSARIO 26
DERECHOS DE AUTOR Y GARANTÍA 28
ÍNDICE
Este manual ha sido encuadernado
con un encuadernador Fastback®
PN: L5648
MANUAL DE INSTRUCCIONES DE LA GUÍA FASTBACK HARDCOVER, REV.:C 09/06/05
16
INTRODUCCIÓN
El sistema de encuadernación Fastback
Hardcover™ es un nuevo sistema
revolucionario para la creación profesional
de libros de tapas duras por encargo.
No es necesaria ninguna preparación
y puede encuadernarse un libro en un
minuto. La clave del sistema es la guía
Fastback Hardcover. La guía realiza las
siguientes funciones:
• Especifica el ancho correcto del lomo de
las tapas.
• Orienta y ayuda en el montaje de sus
páginas impresas dentro de las tapas.
• Orienta y ayuda en la aplicación de las
hojas de títulos Foilfast.
Si busca un modo rentable de fabricar libros
para revender o, si desea encuadernar libros
de recuerdos para sus hijos y amigos,
la solución perfecta es la línea de productos
Fastback Hardcover.
MANUAL DE INSTRUCCIONES DE LA GUÍA FASTBACK HARDCOVER, REV.:C 09/06/05
17
CREAR UN LIBRO DE TAPAS DURAS
Actualmente, hay disponibles tapas duras de Fastback
en muchas medidas habituales, desde tamaño CD a
27,94 cm (11 pulg.), pasando por 21,59 cm (8,5 pulg.).
Puede elegir entre materiales de napa y composición
de calidad superior, y telas artísticas y de biblioteca,
con una gran selección de colores y materiales. Para
obtener más información, consulte a su distribuidor.
Antes de encuadernar sus hojas, coloque las hojas
primera y última de Fastback dobladas en la parte
delantera y trasera de sus páginas impresas (Fig. 1).
Los dobleces deben estar en el lado del lomo de sus
páginas.
Inserte el bloque del libro (con las hojas primera
y última dobladas hacia abajo) en la cavidad de
encuadernación del encuadernador Fastback (Fig. 2).
Encuaderne el libro utilizando una tira Hardcover
Linen. Esta tira ha sido diseñada especialmente para
encuadernar libros de tapa dura. Son más flexibles
que otras tiras de modo que hay una rigidez menor
cuando se pasan las páginas, y además mejoran el
aspecto de su libro.
Puede darse un último toque tradicional añadiendo
una cabezada en la parte superior e inferior del lomo
después de encuadernar el libro. Consulte la página 21.
El ancho correcto de la tapa del lomo queda
determinado por el grosor del bloque del libro
encuadernado. Cuando el bloque de su libro ya
se haya enfriado, colóquelo entre el bloqueo de la
portada derecho morado y el mango del control
deslizante de la esquina derecha delantera de la guía.
Deslice el mango contra el bloque del libro (Fig. 3).
La línea horizontal señala el tamaño de letra del ancho
de portada que debe utilizar. Hay disponibles seis
tamaños de portadas, de la A a la F.
Cuando utilice las portadas más anchas (medidas C
a F), es necesario utilizar los separadores de plástico
que se suministran con la guía. Sin estos separadores,
el bloque del libro podría ladearse, dando como
resultado una encuadernación imperfecta. Los
separadores se guardan en ranuras en la esquina
izquierda trasera de la guía. Suministramos tres
separadores, aunque sólo utilizará dos cada vez.
El tercero es de repuesto. Para utilizar los separadores,
empújelos en las ranuras con letras en los bloqueos
de la tapa según lo indique el ancho correspondiente
(Fig. 4). Por ejemplo, para un libro con ancho E,
los separadores se deberían insertar en las ranuras
marcadas con una “E”.
F I G U R A 2
F I G U R A 3
F I G U R A 4
F I G U R A 1
E
H
G
F
E
D
C
u
MANUAL DE INSTRUCCIONES DE LA GUÍA FASTBACK HARDCOVER, REV.:C 09/06/05
18
Deslice la tarjeta de instrucciones hasta la esquina
derecha superior de la base (Fig. 5). La pestaña
blanca se acopla debajo de la sujeción y el ángulo
izquierdo delantero se acopla en la muesca de
la base. Para tapas más gruesas, se debe
retirar esta tarjeta.
Coloque su Fastback Hardcover™en la guía
con los papeles desprendibles hacia arriba (la
tapa trasera del libro debería estar situada a la
derecha). Deslice la tapa hasta la esquina derecha
trasera de la base (Fig. 6 – Paso 1). Los extremos
derecho y superior de la tapa deberían estar en
contacto con los pasos derecho y trasero de
la base, con la tapa debajo
de los bloqueos del
papel (flechas paso 1). Levante la palanca hacia
la derecha para sujetar en su sitio la tapa dura
(flechas paso 2).
Retire la tira estrecha de papel desprendible a la
derecha del lomo (Fig. 7).
Con la parte delantera de su bloque de libro
hacia arriba, empuje los cantos de las páginas
contra la parte superior y lateral verde de los
bloqueos del papel (y los separadores, si fuese
necesario; consulte la página 17, Fig. 4). Con los
cantos de las páginas sujetos contra los cantos
de los bloqueos del papel y separadores, empuje
con firmeza el canto del lomo del bloque del
libro hacia abajo sobre la tira adhesiva estrecha
descubierta (Fig. 8).
CREAR UN LIBRO DE TAPAS DURAS
(cont.)
F I G U R A 7
F I G U R A 8
F I G U R A 5
F I G U R A 6
MANUAL DE INSTRUCCIONES DE LA GUÍA FASTBACK HARDCOVER, REV.:C 09/06/05
19
CREAR UN LIBRO DE TAPAS DURAS
(cont.)
Con el canto del lomo fijado, gire con cuidado
el bloque del libro a la izquierda. Desprenda el
papel desprendible ancho situado a la derecha
(Fig. 9). Gire la parte trasera del bloque del libro
sobre el adhesivo descubierto, asegurando la
página final trasera.
Desprenda los papeles desprendibles situados a
la izquierda de la tapa, tanto el ancho como el
estrecho (Fig. 10).
Levante la tapa delantera y colóquela sobre la
parte superior del bloque del libro (Fig. 11).
Los cantos de la tapa deben estar en contacto
con los bloqueos de la tapa morados posterior
y lateral (detalle flecha Fig. 11). Después presione
la tapa hacia abajo sobre el bloque del libro.
Levante la palanca hacia arriba para soltar su libro.
Abra cada tapa para alisar las páginas interiores
primera y última (Fig. 12).
¡Ya está hecho su libro Fastback®Hardcover™!
F I G U R A 10
F I G U R A 11
F I G U R A 12
F I G U R A 9
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
MyBinding Powis Fastback Hardcover Manuel utilisateur
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
Autres documents
-
Powis Parker Fastback 20 Manuel utilisateur
-
Powis Parker FASTBACK 15 Manuel utilisateur
-
Powis Parker FastBack 11 Manuel utilisateur
-
Revell Chi-Town Hustler '69 DODGE CHARGER NHRA FUNNY CAR Manuel utilisateur
-
-
Blaupunkt GTW 1200 Le manuel du propriétaire
-
-
ClosetMaid Book Shelf Kit Guide d'installation
