Renishaw IMP Inductive module probe Guide d'installation
- Taper
- Guide d'installation
© 1996 Renishaw plc Printed in England Ref. IG IMP (E) 1m 03.01 Part No. H-2000-4037-01-C
IMP
Inductive module probe
Part No A-2028-7574 + derivatives
H-2000-4037-01-C
WARRANTY
Equipment requiring attention under warranty
must be returned to your supplier. No claims will
be considered where Renishaw equipment has
been misused, or repairs or adjustments have
been attempted by unauthorised persons.
CHANGES TO EQUIPMENT
Renishaw reserves the right to change
specifications without notice.
IP RATING IP67
ENVIRONMENT
Temperature
The IMP is specified for storage over
–10° to 70°C (14 to 158°F) and operation
over 5° to 60°C (41° to 140°F) ambient
temperature range.
GARANZIA
Apparecchiature che richiedano interventi durante
il periodo di garanzia, devono essere inviate al
Vostro fornitore.
La garanzia non sarà considerata valida qualora
l'apparecchiatura Renishaw sia stata maltrattata,
o sia stata riparata o regolata da personale non
autorizzato.
MODIFICHE ALLE APPARECCHIATURE
La Renishaw si riserva il diritto di apportare
modifiche alle apparecchiature senza preavviso.
CLASSIFICAZIONE IP IP 67
AMBIENTE
Temperatura
La temperatura ambiente di deposito specificata
per è compresa tra –10° e 70°C, e la temperatur
a d'esercizio è compresa tra 5° e 60 °C.
GARANTIE
L'équipement à réparer sous garantie doit
être renvoyé à votre fournisseur.
Aucune réclamation concernant l'équipement
Renishaw ne sera étudiée en cas d'utilisation
impropre, de réparations ou de réglages effectués
par toute personne non autorisée.
MODIFICATION DE L'EQUIPEMENT
Renishaw se réserve le droit de modifier les
spécifications de l'équipement sans préavis.
CONFORMITE IP IP67
ENVIRONNEMENT
Température
Le IMP est conçu pour une conservation
à température ambiante comprise entre
–10° et +70°C et une exploitation à température
ambiante comprise entre 5° et 60°C.
GARANTIE
Teile, die während der Garantiezeit Mängel
aufweisen, müssen an den Lieferanten
zurückgesandt werden.
Die Garantieansprüche verfallen bei
Fehlbedienung oder unsachgemäßem Eingriff.
Technische Änderungen
Technische Änderungen vorbehalten.
Dichtheit IP67
Umgebungsbedingung
Temperatur
Arbeitstemperatur –10° – 70°C
Lagertemperatur 5° – 60°C
This product conforms to the following European standards:
BS EN 50081-2 and BS EN 50082-2.
It complies with the relevant essential health and safety and protection
requirements of the following EC Directives:
89/336/EEC as amended (EMC), and 93/68/EEC (CE MARKING).
Important
All relevant safety information, including that incorporated in the installation
instructions, user instructions and maintenance instructions must be observed.
Ce produit est conforme aux normes Européennes suivantes :
BS EN 50081–2 et BS EN 50082–2.
Il se conforme aux prescriptions de santé et sécurité et aux
recommandations de protection des directives suivantes de l'UE:
89/336/EEC modifiée (CEM) et 93/68/EEC (MARQUAGE CE).
Important
Toutes les consignes de sécurité pertinentes, y compris celles figurant aux
paragraphes concernant l'installation, l'utilisation et la maintenance du bloc
d'alimentation doivent être suivies.
Dieses Produkt entspricht den folgenden europäischen Normen
BS EN 50081-2 und BS EN 50082-2.
Dies beinhaltet auch alle für das Produkt zutreffende Gesundheits-,
Sicherheits- und Schutzvorschriften gemäß den EG-Richtlinien:
89/336/EEC und 93/68/EEC (CE Kennzeichnung).
Wichtig
Alle Sicherheitshinweise im Handbuch, in den Kapiteln Installation,
Bedienung und Wartung, müssen beachtet werden.
Questo prodotto é conforme ai seguenti standard Europei:
BS EN 50081–2 e BS EN 50082–2.
L'apparecchiatura è conforme ai requisiti di protezione e di antinfortunistica della
normativa EEC: 89/336/EEC ed emendamenti (CORRENTE ELETTROMAGNETICA)
e 93/68/EEC (MARCHIO CE).
Avvertenza
E' essenziale osservare le informazioni di antinfortunistica, comprese quelle contenute
nelle sezioni relative all'installazione, al funzionamento ed alla manutenzione.
FCC Section 15.19
This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
1. This device may not cause harmfull interference.
2. This device must accept any interference received, including interference that
may cause undesired operation.
FCC Section 15.105
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference,
in which case you will be required to correct the interference at your own expense.
FCC Section 15.21
The user is cautioned that any changes or modifications not expressly approved by
Renishaw plc, or authorised representative could void the user's authority to operate
the equipment.
FCC Section 15.27
The user is also cautioned that any peripheral device installed with this equipment
such as a computer, must be connected with a high quality shielded cable to insure
compliance with FCC limits.
FCC DECLARATION (USA)
Installation Guide
Renishaw plc, New Mills, Wotton-under-Edge,
Gloucestershire GL12 8JR, United Kingdom.
International Tel +44 1453 524524 National Tel 01453 524524 [07000 RENISHAW]
International Fax +44 1453 524901 National Fax 01453 524901
Internet http://www.renishaw.com email [email protected]
Telex 437120 RENMET G
La page charge ...
-
1
-
2
Renishaw IMP Inductive module probe Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Renishaw IMM Inductive module machine Mode d'emploi
-
-
-
-
-
-
-
Renishaw NCi-4 Installation & User's Guide
-
-