Barco HDX wi-fi module Manuel utilisateur

Taper
Manuel utilisateur
ENABLING BRIGHT OUTCOMES
Safety Manual
For Pulse Input & Communication Unit
WiFi & GSM Modules
Barco NV
Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Registered office: Barco NV
President Kennedypark 35, 8500 Kortrijk, Belgium
www.barco.com/en/support
www.barco.com
Changes
Barco provides this manual 'as is' without warranty of any kind, either expressed or implied, including but not limited to the implied
warranties or merchantability and fitness for a particular purpose. Barco may make improvements and/or changes to the product(s) and/or
the program(s) described in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to the information in this
publication; these changes are incorporated in new editions of this publication.
The latest edition of Barco manuals can be downloaded from the Barco web site www. barco.com or from the secured Barco web site
https://www.barco.com/en/signin.
Disposal Information
Waste Electrical and Electronic Equipment
This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and
electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to
the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle
them responsibly to promote the sustainable reuse of material resources.
For more information about recycling of this product, please contact your local city office or your municipal waste disposal service.
For details, please visit the Barco website at: http://www.barco.com/AboutBarco/weee
Copyright ©
All rights reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise be recorded, transmitted or
stored in a retrieval system without the prior written consent of Barco.
Guarantee and Compensation
Barco provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms of guarantee. On receipt, the
purchaser must immediately inspect all delivered goods for damage incurred during transport, as well as for material and manufacturing
faults Barco must be informed immediately in writing of any complaints.
The period of guarantee begins on the date of transfer of risks, in the case of special systems and software on the date of commissioning,
at latest 30 days after the transfer of risks. In the event of justified notice of complaint, Barco can repair the fault or provide a replacement
at its own discretion within an appropriate period. If this measure proves to be impossible or unsuccessful, the purchaser can demand a
reduction in the purchase price or cancellation of the contract. All other claims, in particular those relating to compensation for direct or
indirect damage, and also damage attributed to the operation of software as well as to other services provided by Barco, being a
component of the system or independent service, will be deemed invalid provided the damage is not proven to be attributed to the
absence of properties guaranteed in writing or due to the intent or gross negligence or part of Barco.
If the purchaser or a third party carries out modifications or repairs on goods delivered by Barco, or if the goods are handled incorrectly, in
particular if the systems are operated incorrectly or if, after the transfer of risks, the goods are subject to influences not agreed upon in the
contract, all guarantee claims of the purchaser will be rendered invalid. Not included in the guarantee coverage are system failures which
are attributed to programs or special electronic circuitry provided by the purchaser, e. g. interfaces. Normal wear as well as normal
maintenance are not subject to the guarantee provided by Barco either.
The environmental conditions as well as the servicing and maintenance regulations specified in this manual must be complied with by the
customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights of their respective holders.
All brand and product names mentioned in this manual serve as comments or examples and are not to be understood as advertising for
the products or their manufacturers.
R5906162 /00 WiFi & GSM Modules 5
1 Safety
About this document
Read this document attentively. It contains important information on the WiFi & GSM module kits for the Pulse Input & Communication
unit. This document does not contain installation information. The latest edition of the installation manuals can be downloaded from the
Barco website.
1.1 Compliance FCC
Federal Communication Commission Interference Statement
You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user's
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation of the device.
FCC RF Radiation Exposure Statement:
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
1.2 Compliance IC
Radio Frequency (RF) exposure information
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Industry Canada statement
This device complies with Industry Canada's license-exempt RSSs
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.
Operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite
systems. For the frequency 5600-5650 MHz, no operation is permitted".
Industry Canada class A emission compliance statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Canadian ICES-003.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Informations concernant lexposition aux fréquences radio (RF)
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.
Avis dindustrie Canada
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1. l'appareil ne doit pas produire de brouillage, et
2. l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Safety
R5906162 /00 WiFi & GSM Modules6
La bande 5 150-5 250 MHz est réservés uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable
aux systèmes de satellites mobiles utilisant les mêmes canaux.
Pour la fréquence 5600-5650 MHz, aucune opération est autorisée
Avis de conformité a la réglementation d'Industrie Canada
Cet appareil numérique de la classe A est conforme a la norme NMB-003 du Canada.
1.3 CE Certification
CE Certification
Pulse Input & Communication unit is fit for use in all European Union countries, Norway and Switzerland.
Image 1-1
The Pulse Input & Communication unit are restricted to indoor use only when operating in the 5150 to 5250 Mhz frequency
range.
Hereby, Barco NV declares that the Pulse Input & Communication unit are in compliance with the Directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet address: (Correct link to be provided).
WiFi & GSM module
For WLAN:
Frequency: 2402 MHz - 2482 Mhz
Max EIRP: 19 dBm
Frequency: 5150 5350 MHz / 5470 5725 Mhz
Max EIRP: 23 dBm
For GSM:
E-GSM:
- Frequency: 900 MHz
- Max EIRP: 33.5 dBm
EDGE:
- Frequency: 900 MHz
- Max EIRP: 28 dBm
DCS:
- Frequency: 1800 MHz
- Max EIRP: 30.5 dBm
EDGE:
- Frequency: 1800 MHz
- Max EIRP: 27 dBm
For UMTS:
Band 1:
- Frequency: 2100 MHz
- Max EIRP: 24 dBm
Band 8:
- Frequency: 900 MHz
- Max EIRP: 24 dBm
Safety
R5906162 /00 WiFi & GSM Modules 7
Safety
Registered office: Barco NV | President Kennedypark 35, 8500 Kortrijk, Belgium
Barco NV | Beneluxpark 21, 8500 Kortrijk, Belgium
www.barco.com
R5906162 /00 | 2018-09-16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Barco HDX wi-fi module Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues