Midmark 6214 Workstation Mode d'emploi

Style P

Mobile Workstations

For Models:

6211, 6212, 6213, 6214,

6215, 6217, 6218 , & 6219

User Guide

TP202 20-42-FO-00014 Rev A1 C2169

003-10179-99 Rev. AA2 (11/15/2018)

English - 2

003-10179-99 © Midmark Corporation 2018

Model / Serial Number:

Date of Purchase:

Midmark Authorized Service

Company:

Dealer:

Product Information

Model / Serial

Number Locations

English - 3

003-10179-99 © Midmark Corporation 2018

Table of Contents

Product Information ...............................................................................................................2

Important Information

Product Registration .............................................................................................................4

Transportation / Storage Conditions ...................................................................................4

Intended Use ..........................................................................................................................4

Disposal of Equipment .......................................................................................................... 4

Authorized Representatives ................................................................................................. 5

Safety Symbols ...........................................................................................................6

Operation

Cutting Zip Tie ........................................................................................................................7

Raise and Lower Workstation Top ......................................................................................8

Caster Break Pedal ............................................................................................................................9

Adjusting Monitor Tension ..................................................................................................10

Adjusting Monitor Float Tower Tension ............................................................................10

Removing Countertop .........................................................................................................11

Adjusting Extension Front Form Factor............................................................................11

Moving Mouse Tray .............................................................................................................12

Adjusting Mobile Printer Shelf ...........................................................................................12

Battery Indicator Display ....................................................................................................13

Changing Height of CPU Holder or Column Basket ....................................................... 13

Placing CPU in Holder ........................................................................................................14

Removing Extender Plate ..................................................................................................14

Maintenance

Calling for Service ...............................................................................................................15

Cleaning ...............................................................................................................................................15

Preventative Maintenance..................................................................................................15

Specications

Workstations ........................................................................................................................16

Accessory .............................................................................................................................16

Warranty

Midmark Workstation Limited Warranty ...........................................................................17

English - 4

003-10179-99 © Midmark Corporation 2018

Important Information

Product Registration

To register your product, go to www.midmark.com

Transportation / Storage Conditions

Ambient Temperature Range: ................................................................ 50°F to 120°F (+10°C to +48.9°C)

Relative Humidity.........................................................................................10% to 85% (non-condensing)

Intended Use

Provide a mobile and height adjustable workstation that provides support for multiple technology

form factors. The work surface is intended to provide ergonomic positioning of supported equipment

for users ranging from a seated 5th percentile female to a standing 95th percentile male.

Disposal of Equipment

At the end of product life, the workstation, accessories, and other consumable goods may

become contaminated from normal use. Consult local codes and ordinances for proper disposal

of equipment, accessories and other consumable goods.

Note:

The battery for the Midmark Mobile Workstation is a lithium ion battery and must be recycled or

disposed of properly according to national or local regulations.

Warning

Do not move workstation if there are obstructions in front of or under the caster. Failure to

remove obstructions may cause tipping hazard.

Warning

Use of this equipment with damaged or excessive wear on casters may result in a tipping

hazard.

Warning

Do not move workstation while extension cord or other cords are plugged in or not secured into

proper storage bins or management systems.

Warning

Cylinder force and option selections are specific to their configuration. Please contact Midmark

Technical Service before making any modifications to the cart.

English - 5

003-10179-99 © Midmark Corporation 2018

Authorized Representatives

Customers in the US and Canada should direct all questions, incidents, complaints, and service requests to

Midmark’s Corporate directly.

1-800-MIDMARK (1-800-643-6275)

8:00 am until 5:00 pm Monday - Friday (EST)

www.midmark.com

Customers in the EU should direct all questions, incidents, and complaints to Midmark’s Authorized

Representative listed below.

Promotal Srl.

Via Lenin 79/A

Quattro Castella (RE), 42020, Italy

Phone: +39.0522.875.166

Fax: +39.0522.243.096

Customers in India should direct all questions, incidents, and complaints to Midmark’s Authorized

Representative listed below.

Midmark India

Kalpataru Point, Unit No. 12, 1st Floor Kamani road, Sion (E)

Mumbai, 400022

Tel:+91 22 4915 3000

Fax:+91 22 4915 3100

Customers in Saudi Arabia should direct all questions, incidents, and complaints to Midmark’s Authorized

Representative listed below.

Attieh Medico Ltd

Abdullah M. Al Khali Street

Al Nakheel Dist. II

P.O. Box 116105

Jeddah (East)

21391

Saudi Arabia

Tel: + 966 2 286 4707

Fax: + 966 2 286 4744

Customers in the United Arab Emirates should direct all questions, incidents, and complaints to Midmark’s

Authorized Representative listed below.

GULF DRUG LLC.

Al Barsha,

Dubai, UAE

Phone: +971 4 501 4000

Fax: +971 4 501 4100

English - 6

003-10179-99 © Midmark Corporation 2018

Catalogue Number

Manufacturer

Serial Number

WARNING

Indicates a potentially hazardous situation which could result in serious injury.

Important Information - Safety Symbols

Caution

Indicates a potentially hazardous situation which may result in minor or moderate injury. It

may also be used to alert against unsafe practices

Equipment Alert

Indicates a potentially hazardous situation which could result in equipment damage.

Proper shipping orientation

Fragile

Refer to manual

Keep dry

Note

Amplifies a procedure, practice, or condition.

Symbol Glossary

Pressure Limit

140 F

60 C

-22 F

-30 C

Temperature Limit

English - 7

003-10179-99 © Midmark Corporation 2018

Cutting Zip Tie

WARNING

Pressurized gas cylinder assembled in this workstation. Assemble and attach all work surface

mounted options prior to cutting cable tie around brake handle and raising the workstation. To

avoid injury, keep your head and body parts away from the work surface.

English - 8

003-10179-99 © Midmark Corporation 2018

Raise and Lower Workstation Top

Hold workstation top with both hands while pressing handle to move workstation top up or down.

WARNING

Pressurized gas cylinder assembled in this workstation. Assemble and attach all work surface

mounted options prior to cutting cable tie around brake handle and raising the workstation. To

avoid injury, keep your head and body parts away from the work surface.

English - 9

003-10179-99 © Midmark Corporation 2018

Caster Break Pedal

Pressing down on break pedal prevents both wheel and caster from rotating.

Caster Release Pedal

Pressing down on release pedal allows both wheel and caster to rotate.

English - 10

003-10179-99 © Midmark Corporation 2018

Adjusting Monitor Tension (6212, 6213, 6218, & 6219)

Increase or decrease tension on monitor pivot with Allen Wrench on monitor mount.

Increase

Decrease

Adjusting Monitor Float Tower Tension

A. Use the 3/16” Allen wrench to remove screws (2) from plastic top cap of float tower.

B. Remove and install pins as necessary per the label on tower. Keep unused pins.

C. Replace plastic cap and secure with screws (2).

English - 11

003-10179-99 © Midmark Corporation 2018

Removing Countertop (6211, 6213, 6217 & 6219)

Turn key to unlock countertop, slide to right and lift to remove from worksurface.

Adjusting Extension Front Form Factor (6213 & 6219)

Remove countertop from worksurface. Loosen screws (3) and adjust extension front form factor

to desired position and tighten screws (3)

Screws

Extension Front

Form Factor

English - 12

003-10179-99 © Midmark Corporation 2018

Adjusting Mobile Printer Shelf

Loosen screws (2) on bottom of mobile printer shelf so teeth as loosened and slide printer tray

out or in aligning teeth and re-tighten screws (2).

Moving Mouse Tray (6217, 6218, & 6219)

Pull mouse tray out from under countertop either side as shown.

English - 13

003-10179-99 © Midmark Corporation 2018

Battery Indicator Display

A. Power button allows user to turn on and off.

B. Battery life indicator allows user to know how much battery life is left for use.

C. Sound button allows user to turn lower battery indicator sound off and on.

C

B

A

Changing Height of CPU Holder or Column Basket

Loosen screws (4) on both sides of clamps or basket to adjust up or down then retighten screws.

English - 14

003-10179-99 © Midmark Corporation 2018

Placing CPU in Holder

Loosen knobs, adjust holder as needed, install CPU and retighten knobs.

Removing Extender Plate

Remove knobs (4), bolts (4) and outer shield of CPU Holder. Install outer shield onto inner shield

loosely with bolts (2) and knobs (2), adjust knobs (2) for CPU width and tighten knobs (2)

English - 15

003-10179-99 © Midmark Corporation 2018

Maintenance

Calling for Service

If service is required, contact your authorized Midmark dealer. (See Authorized Representatives)

Cleaning

Spot cleaning Wash workstation weekly with a mild soap and water rinse with clear water

and dry completely to remove disinfection cleaner build-up.

Difcult stains Wash workstation with a mild solvent.

Disinfecting Disinfect workstation with a solution of standard bleach and water mixed 1 in 10

(10%) or chlorine based cleaners. Follow this with a clear water rinse and

thorough drying of material. See current CDC Guideline for Disinfection &

Sterilization in Healthcare Facilities.

Detailed care and maintenance instructions are included with your product. This information is also available

on www.midmark.com in the Technical library under the User Information tab for your product.

Painted Metal / Plastic Surfaces

Clean the painted metal and plastic surfaces weekly using a clean soft cloth, and mild cleaner.

Preventative Maintenance

Periodically inspect the following areas:

• Power cord(s) should be free of cuts or other visible damage.

• All fasteners should be in place and tightened securely.

• All mechanical functions should operate properly.

Note

Model / serial number information is required when calling for service.

English - 16

003-10179-99 © Midmark Corporation 2018

Specications

Workstation Specications Chart

Models: Worksurface Dimensions

Width x Depth

Worksurface Shelf

Dimensions (W x D)

Range of Motion Height

from Worksurface Top

6211 Secure Laptop

Workstation:

26” x 23” 20.5” x 11”

Min 23”

+

1”

Max 49”

+

1”

6212 Flat Panel PC

Workstation:

26” x 23” N/A

Min 23”

+

1”

Max 49”

+

1”

6213 Flat Panel Secure

PC Workstation:

26” x 23” 20.5” x 11”

Min 23”

+

1”

Max 49”

+

1”

6214 Procedure

Workstation:

26” x 21” N/A

Min 23”

+

1”

Max 49”

+

1”

6215 Compact

Workstation:

26” x 21” N/A

Min 23”

+

1”

Max 49”

+

1”

6217 Secure Laptop

Workstation w/Mouse Tray:

22” x 23” 20.5” x 11”

Min 23”

+

1”

Max 49”

+

1”

6218 Flat Panel PC

Workstation w/Mouse Tray:

22” x 23” N/A

Min 23”

+

1”

Max 49”

+

1”

6219 Flat Panel Secure

PC Workstation

w/Mouse Tray:

22” x 23” 20.5” x 11”

Min 23”

+

1”

Max 49”

+

1”

Accessory Specications Chart

Dimensions (H x L x W) Weight capacity

Drawer Assembly (9A646001 / 9A647001): 5.25” x 10” 14” 3 lbs

Mobile Printer Shelf (9A648001): 3” x 8.75” x 8” 5 lbs

VOIP Shelf (9A649001 / 9A649002): 1.5” x 8.75” x 15” 5 lbs

Rear Basket (9A650001): 4” x 6.5” x 16.5” 2 lbs

Equipment Pole (9A651001): 22.5” x 4” x 19” 3 lbs

Single Column Basket (9A652001): 4” x 12” x 17.5” 2 lbs

Double Column Basket (9A653001): 4” x 15.75” x 17.5” 4 lbs

Scale Holder (9A654001): 12.75” x 12.25” x 14.5” 8 lbs

Power Mount (9A655001 / 9A655002): 11.5” x 17.25” x 16.5” N/A

Utility Shelf (9A656001): 8.25” x 12.5” x 17.75” 30 lbs

Blood Pressure Cuff Holder (9A658001): 8.75” x 3” x 3” 2 lbs

Bar Code Holder (9A659001): 3” x 4.25” x 3” 2 lbs

CPU Holder (9A663001) 7.25” x 12.5” x 10” 20 lbs

English - 17

Midmark Workstation Limited Warranty

Extension of Warranty

Midmark™ Corporation (“Midmark”) warrants to the original purchaser its Workstation, manufactured by

Midmark, to be free from defects in material and workmanship under normal interior use and service.

Midmark’s obligation under this warranty is limited to the repair or replacement, at Midmark’s option, of the

parts or the products the defects of which are reported to Midmark within the applicable warranty period

and which upon examination by Midmark prove to be defective.

Applicable Warranty Period

The applicable warranty period, measured from the date of delivery to the original user, shall be as follows:

(a) Five (5) years for all products and components including worksurfaces and drawer fronts, casters

and slides, except for the item in (b).

(b) One (1) years for electrical components such as, cords, controls and accessories..

Exclusions

Midmark’s warranty does not cover sinks, faucets, and plumbing accessories. Any warranties on these

items are extended directly by the manufacturer of these items to the original purchaser. Information on

these manufacturers’ warranties will be enclosed with the applicable products. Also, Midmark will furnish

copies of any of the warranties extended by any such manufacturers upon request.

This warranty does not cover and Midmark shall not be liable for: (1) repairs and replacements required

because of misuse, abuse, negligence, alteration, accident, freight damage, or tampering; (2) matching of

color, grain, or texture except to commercially acceptable standards; (3) changes in color caused by

natural or articial light; (4) products which are not installed, used, and properly cleaned as required in

Midmark’s written Installation Manual; (5) specially manufactured products; (6) products considered to be

of consumable nature such as light lamps and surge suppression product; (7) accessories or parts not

manufactured by Midmark; (8) charges by anyone (including Midmark’s authorized Midmark Dental Case-

work dealers) for adjustments, repairs, replacement parts, installation, or other work performed upon or in

connection with such products which is not expressly authorized in writing in advance by Midmark.

Exclusive Remedy

Midmark’s only obligation under this warranty is the repair or replacement of defective parts. Midmark shall

not be liable for any direct, special, indirect, incidental, exemplary, or consequential damages or delay.

No Authorization

No person or rm is authorized to create for Midmark any other obligation or liability in connection with the

products.

THIS WARRANTY IS MIDMARK’S ONLY WARRANTY AND IS IN LIEU OF ALL OTHER WARRANTIES,

EXPRESS OR IMPLIED. MIDMARK MAKES NO IMPLIED WARRANTIES OF ANY KIND INCLUDING

ANY WARRANTIES OF MERCHANT-ABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. THIS

WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT OF DEFECTIVE PARTS.

English - 18

Notes:

English - 19

Notes:

Midmark Corporation

60 Vista Drive

Versailles, OH 45380 USA

1-800-643-6275

1-937-526-3662

TP202 20-42-FO-00014 Rev A1 C2169

www.midmark.com

La page charge ...

Midmark 6214 Workstation Mode d'emploi

Ce manuel convient également à

Midmark 6214 Workstation Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents