HeatStar ER2STG125-LP Le manuel du propriétaire

— WHAT TO DO IF YOU SMELL GAS

• Open Windows

• DO NOT try to light any appliance.

• DO NOT use electrical switches.

• DO NOT use any telephone in your house. Immediately call your local gas supplier from a location remote from

the leak. Follow the gas supplier’s instructions.

• Do not touch any electrical switch; do not use any phone in your building.

• Installation and service must be performed by a qualified installer, service agency or the gas supplier.

• If you cannot reach your gas supplier, call the Fire Department.

FOR YOUR SAFETY:

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

WARNING: If the information in these instructions are not followed exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

ENERCO Group, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 866-447-2194

WARNING: Improper installation, adjustment, alteration, service or maintenance can cause

property damage, injury, or death. Read the installation, operating and maintenance instructions

thoroughly before installing or servicing this equipment

OPERATING INSTRUCTIONS

AND OWNER’S MANUAL

READ INSTRUCTIONS CAREFULLY: Read and follow all instructions.

Place instructions in a safe place for future reference. Do not allow anyone who has

not read these instructions to assemble, light, adjust or operate the heater.

Model #

2STG

ER

LANGUAGES INCLUDED

•ENGLISH

•FRENCH

•SPANISH

Heatstar ER2STG

Gas-Fired Low-Intensity Infrared Heaters Approved

For Commercial Applications

ER2STG 60-100

ER2STG 80-125

ER2STG 125-175

2

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

Installer Responsibility

All heaters and associated gas piping should be installed in

accordance with applicable specifications and this installation

made only by firms (or individuals) well qualified in this type of

work. Consult local building inspectors, Fire Marshals or your

local Enerco Group, Inc Factory Representative for guidance.

Heatstar ER2STG heaters are installed on the basis of

information given in a layout drawing, which together with the

cited codes and regulations, comprise the basic information

needed to complete the installation. The installer must

furnish all needed material that is not furnished as standard

equipment, and it is his responsibility to see that such materials,

as well as the installation methods he uses result in a job that is

workmanlike and in compliance with all applicable codes.

Enerco Group, Inc Factory Representatives have had training

and experience in the application of this equipment and can

be called on for suggestions about installation which can save

material and money.

WARNING:

FIRE, BURN, INHALATION, AND EXPLOSION HAZARD.

KEEP SOLID COMBUSTIBLES, SUCH AS BUILDING MATERI-

ALS, PAPER OR CARDBOARD, A SAFE DISTANCE AWAY

FROM THE HEATER AS RECOMMENDED BY THE INSTRUC-

TIONS. NEVER USE THE HEATER IN SPACES WHICH DO OR

MAY CONTAIN VOLATILE OR AIRBORNE COMBUSTIBLES,

OR PRODUCTS SUCH AS GASOLINE, SOLVENTS, PAINT

THINNER, DUST PARTICLES OR UNKNOWN CHEMICALS.

GENERAL HAZARD WARNING:

FAILURE TO COMPLY WITH THE PRECAUTIONS AND

INSTRUCTIONS PROVIDED WITH THIS HEATER, CAN

RESULT IN DEATH, SERIOUS BODILY INJURY AND

PROPERTY LOSS OR DAMAGE FROM HAZARDS OF

FIRE, EXPLOSION, BURN, ASPHYXIATION, CARBON

MONOXIDE POISONING, AND/OR ELECTRICAL SHOCK.

ONLY PERSONS WHO CAN UNDERSTAND AND FOL-

LOW THE INSTRUCTIONS SHOULD USE OR SERVICE

THIS HEATER.

IF YOU NEED ASSISTANCE OR HEATER INFORMATION

SUCH AS AN INSTRUCTIONS MANUAL, LABELS, ETC.

CONTACT THE MANUFACTURER.

WARNING:

YOUR SAFETY IS IMPORTANT TO YOU AND TO OTHERS,

SO PLEASE READ THESE INSTRUCTIONS BEFORE YOU

OPERATE THIS HEATER.

CONTENTS

Section 1 INTRODUCTION.........................................................2

Section 2 PLANNING.................................................................3

Section 3 INSTALLATION & ASSEMBLY.....................................6

Section 4 ENGINEERING SPECIFICATIONS ..............................12

Section 5 VENTING/DUCTING………………………………………… 13

Section 6 GAS PIPING..............................................................16

Section 7 WIRING....................................................................17

Section 8 OPERATION MAINTENANCE....................................18

Section 8 TROUBLESHOOTING................................................20

Section 9 REPLACEMENT PARTS..............................................23

WARRANTY INFORMATION....................................................24

WARNING:

THIS PRODUCT CAN EXPOSE YOU TO CHEMICALS INCLUDING

LEAD AND LEAD COMPOUNDS, WHICH ARE KNOWN TO THE

STATE OF CALIFORNIA TO CAUSE CANCER AND BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM. FOR MORE INFORMATION

VISIT WWW.P65WARNINGS.CA.GOV

SECTION 1:Introduction

Heatstar ER2STG models are low-cost, field assembled infrared

heaters that are easy to install and require only minimal

maintenance. They are designed to provide years of economical

operation and trouble-free service.

Checking Shipment

Check the shipment against the Bill of Lading for shortages.

Also, check for external damage to cartons. Note any

shortages, and/or external damage to cartons on the Bill of

Lading in the presence of the delivery trucker. The delivery

trucker should acknowledge any shortages or damage by

initializing this “noted” Bill of Lading. Immediately report any

claims for damaged material, or shortages that were not

evident at the time of shipment, to the carrier and your Enerco

Group, Inc Factory Representative.

WARNING:

Fuels used in liquefied propange gas appliances, and the products

of combustion of such fuel, can expose you to chemicals including

benzene, which is known to the state of California to cause can-

cer and cause birth defects or other reproductive harm, for more

information go to www.P65Warnings.ca.gov

3Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

SECTION 2: Planning

The following codes and instructions should be followed when

planning the installation of the Heatstar ER2STG heater. In

addition to these instructions, the warnings in (Section 1) must

be carefully adhered to since improper installation may lead to

property damage, injury, or death.

National Standards and Applicable

Codes

Gas Codes:

The type of gas appearing on the nameplate must be

the type of gas used. Installation must comply with local

codes and recommendations of the local gas company,

and the National Fuel Gas Code, ANSI Z223.1 – latest

revision, (same as NFPA Bulletin 54) or the Natural Gas

and Propane Installation Code, CSA B149.1.

• Clearance between the heater and its vent and adjacent

combustible material (which is part of the building or its

contents) shall be maintained to conform with the Stan-

dard for Installation of Gas Appliances and Gas Piping,

NFPA-54 /ANSI Z223.1 – latest revision, National Fuel

Gas Code or the Natural Gas and Propane Installation

Code, CSA B149.1.

Aircraft Hangers:

Installation in aircraft hangers must be in accordance

with the Standard for Aircraft Hangers, ANSI / NFPA-

409 – latest revision.

• Heaters in aircraft storage or service areas shall be in-

stalled at a height of 10 feet above the upper surface of

wings or engine enclosures of the highest aircraft which

may be housed in the hanger. (This should be measured

from the bottom of the heater to the wing or engine

enclosure, whichever is highest from the floor.)

• In other sections of aircraft hangers, such as shops or

offices, heaters must not be installed less than 8 feet

above the floor.

• Heaters installed in aircraft hangers shall be located

so as not to be subject to damage by aircraft, cranes,

moveable scaffolding or other objects.

Public Garages:

Installations in garages must be made in accordance

with the Standard for Parking Structures, NFPA-88A –

latest revision or the Standard for Repair Garages, NFPA-

88B – latest revision.

• Heaters must not be installed less than 8 feet above

the floor. Minimum clearances to combustibles must be

maintained from vehicles parked below the heater.

• When installed over hoists, minimum clearances to com-

bustibles must be maintained from the uppermost point

on the hoist.

Venting:

The venting must be installed in accordance to the latest

revision of ANSI Z223.1 or CSA 149.1. Partial informa-

tion with regard to this code is provided in (Section 5) of

this installation manual with regard to size and configu-

rations for venting arrangements.

• Any portion of flue pipe passing through a combus-

tible wall must be dual insulated or have an approved

thimble. Refer to to the latest revision of ANSI Z223.1 or

CSA 149.1

Hazardous Locations:

Where there is the possibility of exposure to combustible

airborne material or vapor, consult the local Fire

Marshal, the fire insurance carrier or other authorities

for approval of the proposed installation.

Critical Considerations

Heatstar ER2STG is a suspended heater. Therefore, its

stability, flexibility, and safety are very important. Before

starting installation, be sure the system can meet the

following requirements.

• For use in indoor or outdoor installation. Not for use in

residential dwellings.

• Maintain specified clearances to combustibles, and safe

distance from the heat-sensitive material, equipment

and work stations.

• The stated clearances to combustibles represent a sur-

face temperature of 90°F (30°C) above room

temperature. Building materials with low heat tolerance(

such as plastic, vinyl siding, canvas, etc.) may be subject

to degradation at lower temperatures. It is the install-

ers responsibility to assure that adjacent materials are

protected from degradation.

• Provide a suspension with vertical length of chain or

swinging rod which has at least 2 inches of horizontal

travel for each burner in a straight run. Be sure the sus-

pension system is sufficiently flexible to accommodate

thermal expansion which occurs as the system heats up

(see Figure 6 on page 11).

• Provide access to burners for servicing, preferable on

both sides, above and behind the burner for removal.

• Provide a minimum of 18 inches of clearance between

burners and building walls. (Always observe minimum

clearances to combustibles.)

• Be sure the heater has a downward pitch of one-half

inch per 20 feet away from the burner.

• Provide signs in storage areas to specify maximum stack-

ing height to maintain required clearances to combus-

tibles.

• Plan location supports (see Figure 2A-D on page 8).

Locate a support near all elbows.

• The installation must conform with local building codes

or in the absence of local codes, with the National Fuel

Gas Code, ANSI Z223.1/NFPA 54 or the Natural Gas

and Propane Installation Code, CSA B149.1.

• If an external electrical source is utilized, the heater,

when installed, must be electrically grounded in accor-

dance with the National Electical Code, ANSI/ NFPA 70

or current Canadian Electrical Code, CSA C22.1.

Available Venting Kits

F102848 Category I 4" Vertical Vent Kit

F102849 Category I 6" Vertical Vent Kit

F102860 Category III 4" Stainless Steel Horizontal Vent

Kit

4

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

TABLE 1: Minimum Clearances to Combustibles (Use Figure 1 on page 5 as a Guide)

Reflector Type Position ER2STG-100 ER2STG-125 ER2STG-175

Standard

Reflector

(Horizontal)

A

B

C

D

6”

36”

74”

36”

6”

36”

87”

36”

8”

36”

87”

36”

45° Reflector Tilt

A

B

C

E

F

18”

36”

74”

36”

60”

18”

36”

87”

36”

60”

18”

36”

87”

36”

60”

U-Tube Standard

(Horizontal)

A

B

C

D

18”

36”

74”

36”

18”

36”

87”

36”

18”

36”

87”

36”

U-Tube Opposite

45°

A

B

C

F

18”

36”

74”

60”

18”

36”

87”

60”

18”

36”

87”

60”

U-Tube Full 45°

A

B

C

E

F

18”

36”

74”

36”

60”

18”

36”

87”

36”

60”

18”

36”

87”

36”

60”

Unvented Above A 36” 36” 36”

WARNING:

FIRE OR EXPLOSION HAZARD

CAN CAUSE PROPERTY DAMAGE, SEVERE INJURY OR DEATH.

In all situations, clearances to combustibles must be maintained. Failure to observe clearances to combustibles may result in property

damage, severe injury, or death.

Minimum clearances must be maintained from vehicles parked below the heater. Signs should be posted in storage areas to specify

maximum stacking height to maintain required clearances to combustibles.

Caution should be used when running the system near combustible materials such as wood, paper, rubber, etc. Consideration should be

given to partitions, storage racks, hoists, building construction, etc.

TABLE 1 gives minimum acceptable clearances to combustibles. Clearances as shown in TABLE 1 are not for use in four-sided enclosures.

Clearances To Combustibles

5Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

D

A

C

STANDARD REFLECTOR

A

E

C

E

45 DEGREE REFLECTOR TILT

C

A

EF

U-TUBE OPPOSITE 45 DEGREE

A

CD

U-TUBE STANDARD

C

E

A

E

U-TUBE FULL 45

BE

FRONT AND BACK CLEARANCE

Clearances To Combustibles

Figure 1: Clearances To Combustibles (Refer to TABLE 1 on page 4)

A

C

EF

STANDARD REFLECTOR

D

A

C

A

C

D

“U”-Tube, Standard

A

C

D

F

“U”-Tube, Opposite 45°

F

C C

AA

E

A

F

“U”-Tube, Full 45°

C

AC

B

Front and Back Clearance

6

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

SECTION 3: Installation & Assembly

TUBE

KEY FOR TUBE COUPLING

(14616)

TUBE HANGER

(14585P)

HEAT EXCHANGER TUBE 10'

(06413)

TURBULATOR BAFFLE 5' (03447)

**NOT INCLUDED WITH ALL MODELS**

REFLECTOR 10'

(00418A)

VENT ADAPTER

(19021)

BURNER BOX

7Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

Vent Adapter

Used to attach the heat

exchanger tubing to vent pipe.

Installation Procedure

Take maximum advantage of the building upper structure, beams, joists, purlins, etc., from which to suspend the heater.

There is no unique sequence for installation of the tubing. On-site observation will usually reveal a logical sequence. Begin

the installation at the most critical dimension. This could save time. Watch for swinging doors, overhead cranes, car lifts etc.

Reflectors and tubing can be installed as you move along. Carefully adjust system pitch at each position to level the heater.

Pitch down one-half inch in 20 feet (away from burner).

DON’T Pressure test the gas line using high pressure (greater than ½ PSIG) without closing the high-pressure shutoff

cocks. Failure to do so will result in damage to the burners.

DO Familiarize yourself with local and national

codes.

Develop a planned procedure which will conserve material and labor on the job.

Check to see that all material and equipment is on the job before starting installation.

Allow for thermal expansion of the hot tube.

Install the gas connector only as shown in instructions (see Figure 14 on page 16).

Have slip joints where required between reflectors to keep them from buckling or coming apart.

Provide 1 sq. inch of free air opening to each 1,000 BTU/hr. of heater input (but not less than 100 sq. inches) in enclosed

spaces. One opening should be within 12 inches of the top and one within 12 inches of the bottom of the enclosure.

Burner Housing

Must always be

installed horizontally.

Tube and Reflector Hanger

Install immediately after first

coupling.

Turbulator

Enerco Group, Inc. normally ships Ener-Radiant heaters with

turbulators assembled into appropriate tubes.

Tube and Reflector Hanger

Suspend system from these hangers.

Minimum two (2) required per tube.

Reflectors

Alternate overlap as shown

on overview. Length of

reflector and amount of

overlap is indicated.

10' 2=1/2" ALUMINIZED

Heat Exchange Tubes

Supplied in 10 ft. lengths.

Tube Coupling Assembly

Coupling should be oriented with

slide bar on top, and all couplings

should “point” in the same direction.

Assemble the heater components as shown in Figures 2a, 2b, 2c, 2d, Optional reflector configurations are shown in (Figure 1). Install

appropriated suspension hardware, beam clamps, chain or rod at predetermined locations. Adjustment of chain length will provide uniform

FIGURE 2: Heatstar ER2STG Overview

8

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

FIGURE 2A: Heatstar Model ER2STG 60-100 Assembly Overview

30 ft. Exchanger length. 31 ft. - 4 in. Total Heater length. 6 Suspension points as indicated.

FIGURE 2B: Heatstar Model ER2STG 80-125 or ER2STG 60-100

40 ft. Exchanger length. 41 ft. - 4 in. Total Heater length. 8 Suspension points as indicated.

FIGURE 2C: Heatstar Model ER2STG 80-125 or ER2STG 125-175

50 ft. Exchanger length. 51 ft. - 4 in. Total Heater length. 10 Suspension points as indicated.

FIGURE 2D: Heatstar Model ER2STG 125-175

60 ft. Exchanger length. 61 ft. - 4 in. Total Heater length. 12 Suspension points as indicated.

ALUMINIZED ALUMINIZED ALUMINIZED ALUMINIZED

18”

Typ.

18” 18” 18”

10’ 2-1/2” 10’ 2-1/2” 10’ 2-1/2” 10’ 2-1/2”

10’ 2-1/2” 10’ 2-1/2” 10’ 2-1/2”

10’ 2-1/2”

18”

Typ.

ALUMINIZED ALUMINIZED ALUMINIZED ALUMINIZED ALUMINIZED

18” 18” 18” 18” 18” 18” 18” 18” 18”

10’ 2-1/2” 10’ 2-1/2” 10’ 2-1/2”

18”

Typ.

ALUMINIZED ALUMINIZED ALUMINIZED ALUMINIZED ALUMINIZEDALUMINIZED

18” 18” 18” 18” 18” 18” 18” 18” 18” 18” 18”

(1) TURBULATOR SECTION (5')

9Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

FIGURE 3: Heatstar ER2STG Dimensions & Suggested Mounting Heights

Turbulator

Heat Exchanger Tubing

Turbulator

Heat Exchanger Tubing

Minimum Total Length (see chart below)

Burner Side View

Burner Ratings and Heat Exchanger Lengths: (NG and LP) Suggested Mounting Heights

Model # Rate (BTU/Hr.)

Low-High

Heat Exchanger

Length Turbulator Minimum

Total Length

Suggested

Min. Space

Typical

Mounting

Height

ER2STG

60-100

60 - 100,000 30 ft. 5 ft. 31' - 4' 12’ - 15’ 12’ - 15’

60 - 100,000 40 ft. None 41' - 4' 15’ - 18’ 12" - 15'

ER2STG

80 - 125

80 -125,000 40 ft. None 41' - 4' 15’ - 20’ 14’ - 19'

80 - 125,000 50 ft. None 51' - 4' 15’ - 18’ 14’ - 19'

ER2STG

125-175

125 - 175,000 50 ft. None 51' - 4' 20’ - 23’ 15’ - 25'

125 - 175,000 60 ft. None 61' - 4' 20’ - 25’ 15’ - 25'

Burner Rear View

9.25"

(23.49cm)

9.25"(23.49cm)

17.75"(45.08)

( IF NECESSARY

10

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

Couplings: Tube and tube fittings are connected by wrap-

around couplings which clamp by means of

a tapered, hammer-driven lock member. The

starting ends of the coupling and lock member

are identified by 1/4” holes which are put

together when starting assembly. Be sure the

tube ends are in line and tube ends butt against

stop pin(s) inside coupling. The slide bar is to be

hammer-driven to a point of securing the coupling

snugly to the tubes. Over-driving will result in

distortion of the coupling or slide bar lip to a

point decreasing the holding the capability of the

coupling. (See Figure 4)

90° Elbow

Elbow Fitting Dimensions

FIGURE 5: Installation of Elbow & Coupling

Elbow Package: Stk. # F106415 Elbow Package includes:

(1) elbow, (1) coupling and (1) refelctor.

Install elbow into radiant tube sequence

where plans indicate a 90° bend

U-Tube Fitting Dimensions 180° U-Tube

Stk. # i ncludes:

F106414 U-Tube Package

(1)U -tube, (1) coupling and (2)

radiant tube sequence where plans

indicate a 180° bend

COUPLING ASSEMBLY

Coupling (Less Key) - 14612

Key for Coupling - 14616

Tighten

Loosen

Hole 1

Coupling

Assembly

Impact

Block

Hole 2

When assembling coupling note

the location of Hole 1 and Hole 2

Orient coupling so that

the impact block is above

tube centerline.

TUBE COUPLING

KEY for COUPLING

FIGURE 4:

(38.73 CM)

(15.24 CM)

18" (45cm)

10"

(25cm)

(10cm)

(43cm)

9" (22cm) Radius

11 Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

Chain kit - Stk. #17370

One chain kit will suspend one 10 ft. section of tube and one 10 ft.

section of reflector.

FIGURE 7A: Tube and Reflector Hanger

FIGURE 7B: Mounting Flange / Tube Detail

1) Insert tube 06413 into front casting to point (A).

2) Tighten set screws marked (B) until snug.

3) After all (3) set screws are snug, turn each

additional 1/4 turn to secure tube in place.

FIGURE 8: Burner Box / Transition Tube Detail

FIGURE 6: Typical Suspension Details

Screw Hook

I-Beam

Beam

S-Hook

Bar Joist

Truss

Concrete

Beam

Mounting Flange

Cap Screw

Stk. 98012

Split Lock Washer

Stk. #98527

Gasket

Stk. #12397

Burner Box

(flame observation

window facing down)

horizontal reflector position (standard)

side 45° reflector position (optional)

FIGURE 9: Reflector End Cap

Parts list

1 00419 Reflector End Cap (Qty 1)

2 09369 Spring Clip (Qty 4)

Flange Kit #06428XL

Kit Includes: Flange,Screws(4), Lock Washers(4), Gasket(1)

12

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

SECTION 4

Engineering Specifications

The total heating system supplied shall be design certified by CSA

under the latest revision of ANSI Z83.20 and CSA 2.34.

A. Burner & Burner Controls

1. Burners shall be capable of firing with one of the fuel options as

specified on the purchase documents: Natural Gas or LP.

2. Burners shall be supplied to fire at any one of the input rates as

specified.

ER2STG 60 - 100 60,000 - 100,000 BTU/Hr.

ER2STG 80 - 125 80,000 - 125,000 BTU/Hr.

ER2STG 125 -175 125,000 -175, 000 BTU/Hr.

3. Burner shall be equipped with a direct sense silicon-carbide hot

surface ignition control system with 100% shut-off ignition device.

Power supplied to each heater shall be 120V, 60Hz, single phase.

Burners shall be rated for 1.0 Amp (run) and 5.0 Amp (start.)

4. Burner shall be equipped with thermal overload motor protec-

tion, balanced air rotor, combustion air proving safety pressure

switch, and viewing window for flame observation.

5. When specified, in contaminated environments, the burner shall

be capable of supplying outside air to each burner for the sup-

port of combustion.

6. All burners shall be pre-wired with a grounded electrical

cord and plug.

7. Low voltage 2-stage thermostat required for correct 2-stage

burner operation.

B. Heat Exchanger

1. Radiant tubing shall be 4” diameter aluminized steel supplied in

10 ft. sections. Sections shall be joined with stainless steel wrap-

around couplings.

2. Reflector to be of aluminum material and designed to direct all

radiant output below horizontal center line of radiant tube.

3. Heaters shall be vented according to manufacturer’s

recommendations.

Gas INLET pressure:

Natural Gas: 4.6” W.C. Min

11.0” W.C. Max

LP Gas: 11.0” W.C. Min

14.0” W.C. Max

1/2” NPT Gas Connector Size

Electrical Rating: (All Models)

120V - 60Hz

1.0 AMP (Run) 5.0 AMP (Start)

Dimensions:

Flue Connection Size…………………4”

Outside Air Connection Size………4”

MANIFOLD PRESSURE

ER2STG 60-100

LOW FIRE

( MIN. RATE)

HIGH FIRE

(MAX RATE)

NATURAL GAS - INCHES

W.C.

1.3" 3.5"

PROPANE - INCHES W.C. 3.5" 10.5"

MANIFOLD PRESSURE

ER2STG 80-125

LOW FIRE

( MIN. RATE)

HIGH FIRE

(MAX RATE)

NATURAL GAS - INCHES

W.C.

1.7" 3.5"

PROPANE - INCHES W.C. 4.2" 10.5"

MANIFOLD PRESSURE

ER2STG 125-175

LOW FIRE

( MIN. RATE)

HIGH FIRE

(MAX RATE)

NATURAL GAS - INCHES

W.C.

2.2" 3.5"

PROPANE - INCHES W.C. 5.8" 10.5"

Gas pressure at MANIFOLD:

1/2” NPT Gas Connector Size

13 Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

SECTION 5

Venting / Ducting

General Requirements

This heater must be vented in accordance with the

specifications

contained in this manual and with the following national codes

and any state, provincial or local codes which may apply:

• Refer to National Fuel Gas Code NFPA 54/ANSI Z223.1- latest

revision.

• CANADA: Refer to Natural Gas and Propane Installation Code

CSA B149.1- latest revision.

The heater may be vented to the outdoors either vertically or

horizontally.

Optional outside air supply may be directed to the heater

horizontally or vertically.

Be sure that the method selected for venting heater complies

with all codes as required for each particular location

The use of single-wall vent pipe (26 gauge) is recommended. A

section of double-wall vent pipe is recommended when passing

through the roof or wall.

Exhaust end of heater will accept a 4'(10 cm) vent pipe using

the vent adapter. Install the vent adapter with the seam on

top, secure all vent joints with a minimum of 3 #8 x 3/8" sheet

metal screws and seal all joints using a high temperature

silicone sealant.

If condensation in the flue is a problem, the flue length should

be shortened or insulated.

Vent pipe must be sloped downward away from the burner

1/4"(.6 cm) for ever 10'(3m).

VENT LENGTHS:

• Maximum total vent length allowed in thirty (30’) feet.

• Maximum outside air supply duct allowed thirty (30’) feet.

• Maximum total vent length plus outside air supply length

shall not exceed fifty (50’) feet.

NOTE:

A total of two (2) elbows are allowed for vent and

outside air supply combination. Subtract 5' feet per additional

elbow from maximum length allowed if 3 or more elbows are

used.

Install a minimum 18" (30 cm) straight length of duct for air

intake or vent before any Tee or elbow.

Alternative Arrangements / Optional Equipment for Venting

Unvented Operation

a) Sufficient ventilation must be provided in the amount of 4

CFM per 1,000 BTU/hr. firing rate.

b) Refer to ANSI Z223.1 - latest revision, NFPA-54 and local

codes for additional information.

c) Use of optional outside combustion air is not recommended

with unvented heaters due to pressure considerations. Refer

to page 16

Horizontal Venting

This heater, when horizontally vented, must be installed

with approved venting system. For horizontal venting

installations these tube heaters are certified as a Category III

appliance

a) Four (4”) inch O.D. flue pipe is required. Thirty (30’) feet

maximum length is recommended.

b) All flue joints should be sealed using suitable product such

as General Electric RTV106 or Permatex Form-A-Gasket Red

High Temperature Silicone Adhesive Sealant.

c) Do not install any elbow or 45 fitting to bring vent lower

than the horizontal tube system.

d) Vent terminal should be installed at a height sufficient to

prevent blockage by snow.

1) Vent must exit building not less than seven (7’) feet

above grade when located adjacent to public walkways.

2) Vent must terminate at least three (3’) feet above any

forced air inlet located within ten feet (10’).

3) Vent must terminate at least four (4’) feet below, four

(4’) feet horizontally from, or one (1’) foot above any

door, window, or gravity inlet into any building.

4) Vent terminal shall be located at least twelve (12”)

inches from any opening through which vent gases

could enter the building.

5) Vent terminal must be beyond any combustible over

hang

Vertical Venting

This heater, when vertically vented, must be installed with

the approved venting system. For vertical vent installations,

ER2STG 60-100 model and ER2STG 80-125 model are category

I appliances. The ER2STG 125-175 model is only Category I

when vented vertically with 6" (15.25cm) diameter vent pipe.

a) Four (4”) inch O.D. flue pipe, maximum thirty (30’) feet

in length may be used as shown with approved vent cap.

(See General Requirements on this page for additional

information.)

b) An insulated thimble may be required to pass through

combustible structures (check local codes).

c) All flue joints should be sealed using suitable products (see

recommendation for horizontal venting.)

Common Venting

a) Horizontal run to vent must never exceed 75% of the

vertical height of the vent. Refer to ANSI Z223.1 - latest

revision, NFA-54 for proper vent sizes and installation.

b) Open area of common vent must equal the sum of the

open area of individual vents connected to it. (See chart

below and diagrams - page 14.)

c) Use double wall vent as required (check codes.)

d) All joints must be sealed using suitable products.

e) Connections to common stack must be positioned to avoid

direct opposition between streams of combustion gases.

COMMON VENTING - (2) Heaters (Horizontal and Vertical)

Model # H = 6 ft. H = 8 ft. H = 15 ft.

ER2STG 60-100 D = 8" D = 8" D = 7"

ER2STG 80-125 D = 10" D = 10" D = 8"

14

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

FIGURE 12: Common Roof Venting

Type "B" Vent required outdoors.

Vent Adapter Stk. #19021

Outside Wall

Secure all joints with 3 (minimum) #8 x 3/8"

sheet metal screws and seal all joints.

H

Vent Cap

Wall Thimble

(If Applicable)

Burner Box

HORIZONTAL COMMON VENTING

VERTICAL COMMON VENTING

SIDE VIEW

TOP VIEW

Type "B" Vent required outdoors.

Vent Adapter Stk. #19021

At least 1/4" per foot rise or pitch

must be maintained on horizontal

runs from heater to vent.

Roof

Secure all joints with 3 (minimum) #8 x 3/8"

sheet metal screws and seal all joints.

H

Approved Vent Cap

Type "B" Vent required outdoors.

Vent Adapter Stk. #19021

Outside Wall

H

Vent Cap

Flashing

Wall Thimble

(If Applicable)

Burner Box Burner Box

Burner Box

D

Burner Box Burner Box

D

4” Aluminized steel Heat Exchange Tube

D

15 Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

FIGURE 10: Unvented Operation

36”

A

1. Ventilation equal to 4 CFM per 1,000 BTU/HR firing rate must

be provided in unvented heater installations

2. For dimensions A "unvented" refer to ( Figure 1- Minimum

Clearances to Combustibles.)

3. This heater requires ventilation in the building to dilute the

products of combustion and provide fresh air for efficient

combustion.

FIGURE 10b: Double Wall

Double wall vent run

Double wall terminal end

FIGURE 11: Vertical Venting

18"(45cm)

18" (45cm) Min. 3'-0" (91cm) Min.

8"(20cm) to 10"(25cm) Max.

6' (182cm) Min.

FIGURE 10A: Single Wall

Single wall vent run

Single wall terminal end

18" (45cm) Min. 3'-0" (91cm) Min.

6' (182cm) Min.

2"(5cm) Clearance thimble

required when u pipe

extends through

combustible materials

(91cm)

Vent Adapter

16

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

Outside Combustion Air Supply

The Heatstar ER2STG heater is approved for installation

with an outside air supply system. Some compounds such as

halogenated hydrocarbons or other corrosive chemicals in the

air can be drawn into the equipment and cause an accelerated

rate of corrosion of some of the heater components. The use

of such chemical compounds near the enclosure should be

avoided.

IMPORTANT: If the building has a slight negative

pressure or contaminants are present in the air, an

outside combustion air supply to the heaters is strongly

recommended.

For an outside air supply, a four (4”) inch O.D. single wall pipe

may be attached to the heater. The duct may be up to thirty

(30’) ft. maximum length or two (2’) ft. minimum length with

no more than two (2) elbows. (See General Requirements on

page 15 for additional information.)

The air supply duct may have to be insulated to prevent

condensation on the outer surface. The outside air terminal

should be securely fastened to the outside wall by drilling four

(4) 1/4” diameter holes in the outside flange; wood screws or

bolts and expansion sleeves may be used to fasten terminal.

PVC Pipe, “Dryer Hose”, or equivalent may be used instead of

standard vent pipe.

FIGURE 13: Non-Pressurized Outside Air Supply Duct

SECTION 6

Gas Piping

Read applicable warnings in (Section 1) before proceeding with

Gas Pipe installation. Improper installation may result in property

damage, severe injury, or death.

Meter and service must be large enough to handle all the burners

being installed plus any other connected load. The gas line which

feed the system must be large enough to supply the required gas

with a maximum pressure drop of 1/2” water column. When gas

piping is not included in the layout drawing, the local gas supplier

will usually help in planning the gas piping.

A 1/2” tapping at each burner location must be located and

oriented as shown in (Figure 14). To check system pressure, put a

plugged 1/8” NPT tapping in the gas line at the connection to the

burner farthest from the supply. Before connecting the burners to

the supply system, verify that all high pressure testing of the gas

piping has been completed. Do not high pressure test the gas piping

with the burners connected.

Follow these instructions to ensure a professional gas supply

installation:

• Support all gas piping with suitable pipe hanging

materials.

• Use wrought iron or wrought steel pipe and malleable

iron fitting. All pipe fittings should be new and free

from defects. Carefully ream the pipe and tubing ends

to remove obstructions and burrs.

• Use L.P. gas-resistant joint compound on all pipe

threads.

• Check the pipe and tubing ends for leaks before

placing heating equipment into service. When

checking for gas leaks, use soap and water solution:

NEVER USE AN OPEN FLAME.

Install the flex gas connector as shown. The flex gas connector

accommodates expansion of the heating system and allows for easy

installation and service of the burner.

FIGURE 14: Gas Line Connection with Stainless Steel Flex Gas

Connector

Shut-Off Valve must be parallel

to burner gas inlet. The 2”

displacement shown is for the cold

condition. This displacement may

reduce when the system is fired.

12"

1/2" Stainless Steel Flex Gas Connector

Stk. #16401

4" (10 cm)

Seal All Joints

Heater Movement

Outside Air

Terminal

Flex Pipe

6" (15 cm) to

12" (30 cm) Long

Flex Pipe

6" (15 cm) to

12" (30 cm) Long

Flex Pipe

6" (15 cm) to

12" (30 cm) Long

Outside Air

Terminal

NOTE:

Flue pipe requires additional

support. Flex pipe will not

support riser and outside

air terminal

Vertical Outside Air

Horizontal Outside Air

FIGURE 14A: Incorrect Gas Line Connection with Stainless

Steel Flex Gas Connector

17 Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

THERMOSTAT CONNECTION

24V

W1

W2

LOW HEAT

HIGH HEAT

R

W1

W2

TUBE BURNER CONNECTIONS INTERNAL THERMOSTAT WIRING

SECTION 7

Wiring

Heaters are normally controlled by thermostats. Heaters must be

electrically grounded in accordance with the National Electrical

Code, ANSI/NFPA 70 or current Canadian Electrical Code, CSA

C22.1.

• If any of the original wire as supplied with the appliance must

be replaced, it must be replaced with wiring material having a

temperature rating of at least 105 °C and rated for 600V

• Each burner must be electrically grounded in accordance with

the National Electric code ANSI/NFPA-70- latest version NOTE:

• Connecting the top two terminals of the bushing

located at the bottom left of the back of the

burner box will give you low fire

• Connect all three of the terminals for high heat

L1

N

Earth Ground

GV

M

T1

PCB1

S1/240

S1/120

N

L1

S2/FS

PSW

W

MV1

GRND

blk

wh

blk

grn

Pressure Switch

24 V

SW1

C1

blk

wh

grn

Primary

Secondary

FC+ FC-

LED

R

F2/IND

F1/120

red

To Thermostat

24V

W1 W2

grn

red

wh

grn

brn

wh

red

Flame Sense

Burner

HSI

wh

blk

wh

yellow

SW1 - Panel Interlock Switch

C1 - 1.5 ufd @ 450 volts

Wire is AWG18 Stranded @ 600 volts - 105 degrees C

Crimp Caps are # CE5 - 105 degrees C

(Neutral Connection Not Needed in this Configuration)

blue

24 VAC

blk

grn

WIRING DIAGRAM

BURNER BOX CONNECTION INTERNAL THERMOSTAT WIRING

FIGURE 18A

FIGURE 18B

18

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

Sequence of Operation

1. Turn the thermostat up. When the thermostat calls for heat,

blower motor will energize.

2. When the motor approaches nominal running RPM, the air

proving switch closes and activates the ignition module.

3. The ignition module then energizes the hot surface igniter

for a timed warm-up period (approximately 45 to 60

seconds.)

4. After the warm-up period, the gas valve is energized.

5. If a flame is detected, the gas valve remains open. When the

call for heat is satisfied, and the system control mechanism

de-energizes the burner line voltage supply, the gas valves

are turned off.

6. If no flame is detected on a three-trial module, the gas

valve is closed, and a purge period begins. After the purge,

the module acts to power the igniter for a second warm-

up period, and a second trial for ignition period. If flame is

still not established, a third and final purge, warm-up, and

trial cycle begins. After three trials, the module will lockout

until reset. Reset is accomplished by removing power from

the module for at least five (5) seconds (thermostat cycle

required.)

7. If flame is established and lost on the first or second trial,

the gas valve is turned off, a purge, warm-up, and trial for

ignition will occur on a three-trial module, only three trials

for ignition are allowed per thermostat cycle.

Maintenance

For best performance, the following maintenance procedures

should be performed before each heating season:

1. Be sure gas and electrical supply to heater are off before

performing any service or maintenance.

2. Check condition of blower scroll and motor. Dirt and dust may

be blown out with compressed air, or a vacuum cleaner may be

used. When using compressed air, do not exceed 30 psi in order

to not damage fragile hot surface igniter.

3. Check condition of burner. Carefully remove any dust or

debris from inside the burner box or burner cup.

4. Inspect the igniter. Replace igniter if there is excessive

carbon residue, erosion, breakage or other defects.

5. Check the inside of the firing tube with a flashlight. If carbon

or scale are present, scrape out the deposits with a wire

brush or rod, or metal plate attached to a wooden pole.

6. Check to see that the burner observation window is clean

and free of cracks or holes. Clean or replace as necessary.

7. Check the flue pipe for dirt. After cleaning as necessary, re-

attach the flue pipe to the heater.

8. Outside surfaces of heater may be cleaned by wiping with a

damp cloth.

9. A qualified service agency should be contacted for service

other than routine maintenance.

10. Check vent terminal and fresh air inlet to see that they have

not been blocked during the non-heating season. If either

pipe is restricted, the air switch won’t close, resulting in a no-

heat situation.

SECTION 8

Operation & Maintenance

Basic Operation of 2-Stage Tube Heater

• Unit fires at rates designated as Low and High

• Fire rate is determined by thermostat

Initial Start:

If thermostat is more than 2 degrees above the room/

space temperature, the heater will start and go into high fire

range. The unit will stay in the high range until the space air

temperature reaches the thermostat set-point. The heater will

shut off.

As the room/space air temperature decreases below the

thermostat set point (approximately 1 degree) the heater will

come on and fire until the thermostat set point is reached.

If the room/space air temperature experiences a rapid

decrease in air temperature (below 3 degrees from set point)

the heater will come on and fire at the high rate until the set

point is reached.

LADDER DIAGRAM

L

N

24V

M

C1

Panel Interlock

F2/IND

F1/120

(Control PCB)

HSI

L1 S1/120

(Control PCB)

PCB

L1

PCB

S2/FSL1

Burner

Flame Sense

T1

115V

PCB

R

PCB

PSW

Pressure Switch

W1

W2

T'Stat

W

MV1

(Control PCB)

Gas

Valve

Earth &

Chassis Ground

FIGURE 18C

HIGH ALTITUDE

Heaters may be fired at full input up to 2000 ft. (610m) above sea level. Above 2000 ft. (610m) a high altitude conversion kit may be required

to ensure proper burner performance, please consult the manufacturer. Be prepared to answer factory questions regarding: type of fuel for the

proposed appliance conversion, gas pressure available at site, and specific altitude at site. The conversion shall be carried out by a manufactur-

er's authorized representative, in accordance with the requirements of the manufacturer, provincial, or territorial authorities having jurisdiction

and in accordance with the requirements of the CSA B149.1 or CSA 149.2 installation codes.

19 Operating Instructions and Owner’s ManualEnerco | Heatstar ER2STG Tube Series Heater

Burner Does Not 1. Check ground wire continuity.

Stay Lit: 2. Check burner internal wiring for reversed

leads.

3. Check insulation on the igniter leads.

4. Clean or replace flame sensor.

5. Replace module if necessary.

IGNITION MODULE LED Status

The Heatstar ER2STG series Tube Heater is equipped with a Ignition

module. This ignition module has a built-in diagnostic program,

which will assist in troubleshooting in the event of a valve-related

problem. The LED or (Light Emitting Diode) is located on the ignition

module as shown in diagram below. The LED status indications are

listed below to help with the troubleshooting.

FIGURE 19:

Off No power to the control

ON Control Fault

1-Flashes Airflow Fault

2--Flashes Flame Sense Fault

3-Flashes Ignition Lockout.

Troubleshooting

CAUTION: Before opening the Heatstar

ER2STG burner door for any type of service, be

sure the gas supply has been shut off at the

heater and the electrical cord from the burner

box has been unplugged.

Blower Motor 1. Is the thermostat calling for heat? Is there

Fails to Run: 120V at the burner receptacle?

2. Check blower side door for seal. Check door

switch. Replace if necessary.

3. Check blower for obstructions. Replace

blower if necessary.

Igniter 1. Check igniter for damage. Replace if

Does Not Glow: necessary.

2. Check voltage and resistance at igniter.

(Voltage should be 120V. Resistance should be

40-75 ohms.)

3. Check for obstructions to the air inlet and

outlet.

4. Check wiring and hose connections to the

air switch. Replace if necessary.

5. Check voltages at transformer primary and

secondary. Replace transformer or module if

necessary.

Valve Does Not Gas pressure downstream of gas control can

Come On: be measure by using a manometer and

connecting to pressure tap on control/

1. Check to see if manual valve heater is ON.

2. Check to see if manual valve knob on heater

gas control in ON.

3. Supply gas pressure can be checked at

1/8” NPT pressure tapping on heater external

manual valve.

4. Check to see if gas control is opening: no

manifold pressure indicates valve is closed.

If the valve is closed, either the gas valve or

the ignition module is faulty.

WARNING: Do not disconnect ground leads

inside heater. Do not interchange grounded

and ungrounded leads on transformer or

ignition module.

Burner Does Not 1. Check to see if gas lines were properly

Light: purged of air.

2. Check inlet and outlet gas pressure during

ignition period.

Natural inlet pressure should be 4.6”

Natural outlet pressure should be set

according to chart on page 12.

LP inlet pressure should be 11.0”

LP outlet pressure should be set according to

chart on page 12.

3. Check for proper orifice and air plate.

IGNITION MODULE

LED

20

Enerco | Heatstar ER2STG Tube Series Heater Operating Instructions and Owner’s Manual

SECTION 8: Troubleshooting Guide. Heatstar ER2STG

START

Turn on thermostat

Does blower turn

on?

Yes

Does the igniter

warm up and glow

red?

Yes

No

Check Thermostat

and Wiring. Is the

power supply to unit

120V?

No

Find the source

of the electrical

problem

Check LED indicator on Ignition Control for

indication of fault. Refer to Ignition Module

testing on page 19 to determine problem.

No Is the air intake or

exhaust blocked?

Yes

Remove Obstruction

Check wiring and

connections

No Is the ignitor

damaged?

No

Check voltage at

ignitor. Is it 120V

during ignition

cycle?

Yes Is blower side door

in place?

No

Replace door

No

Check wiring and

hose connection to

air switch. Are they

OK?

Yes

Is the voltage at

the transformer

secondary 24V?

No

Is the voltage at the

transformer primary

120V

Replace ignitor.

Yes

No

Is the resistance

through igniter 40

to 75 ohms?

Remove door. Is

voltage at door

switch 120?

Yes

No

Check voltage at

Ignition Control

Replace wiring and/

or hose connection.

No

Jumper wires at

pressure switch.

Does the ignitor

glow red?

Yes

Replace transformerYes

Check wire

connections.

Yes

Depress switch.

Does blower come

on?

Yes Yes

No

Check voltage to

motor. Is it 120V?

Yes

Is the blower fan

obstructed?

No

Replace blower

motor.

Replace pressure

switch.

Yes

Replace Ignition

No

Check LED indicator on Ignition Module for

indication of fault. Refer to Ignition Control

testing on page 19 to determine problem.

Check door fit. If

damaged, replace

door.

Replace switch.

No

Remove obstruction

Yes

After ignitor warm-

up period, does the

valve click?

Yes

Does the burner

light?

Yes

Does the burner

stay on?

Yes

Does the burner

run until the call

for heat ends?

If a problem still exists, contact Enerco Group, Inc Technical Products

Customer Service 1-866-447-2194

No

The Ignition Module checks the status of the blower proving switch contacts must see a change in the

contact with every firing cycle. Placing a jumper at the switch out of sequence will result in a fault with

the LED indicator flashing two times.

Were the gas lines purged of air?

No No

Yes

Check inlet gas pressure. Is pressure correct?

Refer to page 12 for correct pressure for unit.

Yes

Check inlet gas shutoff. Adjust regulator.

Contact gas supplier

Is the continuity of

the ground wire

OK?

No

The switch on the gas valve must be in the on

position and the line purged of air.

No

Repair wiring.

No

Check the continuity of the ground wire.

Check the thermostat.

Check outlet gas pressure during ignition cycle.

Refer to page 12 for correct pressure

Yes

Adjust to proper pressure.

No

Are L1 and L2

reversed?

Yes

Repair wiring

Is the wiring at the

Ignition Module

No

Repair wiring

Is the insulation on

the sensor lead OK?

No

Repair wiring

No Yes Yes

Are the wires to

the Ignition Control

OK?

Yes

Replace Ignition

No Replace/repair wires.

Yes

Check for proper

burner orifice and

air plate.

Is the sensor

positioned

properly?

Yes

Is the sensor dirty?

No

Replace Sensor

No Repair/Replace

Yes

Clean sensor.

A fault indication of three flashes may indicate

that the flame sensing circuit is not functioning

properly. Perform the following series of checks

to correct the problem.

No

La page charge ...

HeatStar ER2STG125-LP Le manuel du propriétaire

HeatStar ER2STG125-LP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents